SaMASZ K2BF 210 is a front drum mower designed for mowing standing grass in meadows and stone-free fields. It has a working width of 2.10 m and is equipped with 8 knives. The mower is powered by a tractor's PTO and has a cutting speed of 90.8 m/s. It can be used to mow grass with a height of up to 10 cm and can achieve a working capacity of ~2.4 ha/h. The mower is also equipped with a safety guard and curtain to protect the operator from debris.
SaMASZ K2BF 210 is a front drum mower designed for mowing standing grass in meadows and stone-free fields. It has a working width of 2.10 m and is equipped with 8 knives. The mower is powered by a tractor's PTO and has a cutting speed of 90.8 m/s. It can be used to mow grass with a height of up to 10 cm and can achieve a working capacity of ~2.4 ha/h. The mower is also equipped with a safety guard and curtain to protect the operator from debris.
SaMASZ Sp. z o.o.
Poland, 15-161 Białystok, ul. Trawiasta 15
Rok założenia – 1984
NIP 966-159-29-76
tel. (+48) (85) 664-70-31
fax (+48) (85) 664-70-41
e-mail: samasz@samasz.pl
www.samasz.pl
OPERATOR’S MANUAL
FRONT DRUM MOWERS
K2BF 210 - 2,10 m - 2 Drums
K4BF 265 - 2,65 m - 4 Drums
K4BF 300 - 3,00 m - 4 Drums
IN033EN006
2011.09.13
EDITION NO 6
DANGER
MOWER HAS TO BE SET HORIZONTALLY
TO THE GROUND (GRASS)
DANGER
OPERATING WHEN ANY PERSON
REMAINS IN THE DANGER AREA OF 50 m
Operator’s manual
Front drum mower
K2BF 210; K4BF 265; K4BF 300
- 1 -
Contents page
1.
INTRODUCTION ............................................................................................... 2
2.
TECHNICAL DATA ........................................................................................... 2
2.1.
Specifications ........................................................................................................................... 2
2.2.
Design and working principle .................................................................................................. 4
2.3.
Proper use ................................................................................................................................. 4
2.4.
Standard equipment and spare parts: ........................................................................................ 5
3.
SAFETY ADVICE ............................................................................................... 6
3.1.
Warning decals. ........................................................................................................................ 7
4.
TRANSPORT AND WORKING POSITIONS ................................................ 8
4.1.
Mounting the mower on tractor’s triangle cat. II ..................................................................... 8
4.2.
Adjusting the clearance between triangle’s hook and lock ...................................................... 9
4.3.
Adjusting the length of support chains ..................................................................................... 9
4.4.
Preparing the mower for transport ............................................................................................ 9
4.5.
Mounting PTO shaft ............................................................................................................... 10
4.6.
PTO shaft’s length adjustment ............................................................................................... 11
5.
MOUNTING AND ADJUSTMENTS .............................................................. 12
5.1.
Mounting and timing of the knives ........................................................................................ 12
5.2.
Adjusting the cutting height ................................................................................................... 12
5.3.
Maintenance and service ........................................................................................................ 13
6.
LUBRICATION INSTRUCTION ................................................................... 14
6.1.
Main frame. ............................................................................................................................ 14
6.2.
Intersecting axis gear. ............................................................................................................. 14
7.
DEFECTS AND THEIR REPAIRS ................................................................ 15
7.1.
Disassembly ............................................................................................................................ 15
7.2.
Scrapping ................................................................................................................................ 15
8.
DISASSEMBLY AND WITHDRAWAL FROM USE .................................. 15
9.
WARRANTY CARD ......................................................................................... 16
10.
WARRANTY TERMS. ..................................................................................... 16
10.1.
Warranty terms procedures ..................................................................................................... 16
10.2.
Warranty repairs record .......................................................................................................... 17
Operator’s manual
Front drum mower
K2BF 210; K4BF 265; K4BF 300
- 2 -
1. INTRODUCTION
Operator’s manual is attached to every machine in order that the operator can familiarize
himself with design, working principles, service and adjustment of the mower. The user of
the mower should be familiar with common safety rules and procedures.
The mower is manufactured according to international safety rules.
Compliance with the warnings in this operator’s manual will ensure safe operation.
Please contact your dealer if you have any queries relating to the operation and service of
the mower.
Operator’s manual remains part of mower’s equipment.
GENERAL WARNING
When operating the mower please comply with the warnings and safety
regulations shown throughout this manual by this safety alert symbol.
CAUTION:
Operation of the mower before reading the operator’s manual carefully
as well as operating by the unauthorized staff, especially by children, is
strictly forbidden.
2. TECHNICAL DATA
2.1. Specifications
Front drum mowers manufactured by SaMASZ
®
have the following technical data:
Tab. 1. Technical data
Model K2BF 210 K4BF 26 K4BF 300
Working width
2.10 m 2.65 m 3.00 m
Number of drums
2 4 4
Number of knives 8 (2x4) 12 (4x3) 18 (2x5 + 2x4)
Tractor PTO rpm. 1000 rpm 1000 rpm 1000 rpm
Tractor power required about 55 kW about 65 kW about 74 kW
Working capacity ~2.4 ha/h ~2.8 ha/h ~3.5ha/h
Swath width 0.8 m 1.2
÷
1.6 m 1.2
÷
1.6 m
Transport lenght 1650 mm 1500 mm 1600 mm
Transport width 2300 mm 2700 mm 2950 mm
Operation width 2650 mm 3250 mm 3660 mm
Weight 520 kg 800 kg 870kg
PTO tractor-mower* 540 Nm 540Nm 540 Nm
Cutting speed of the knife 90.8 m/s 90.8 m/s
∅
775mm
91 m/s
∅
613m
90.7 m/s
Drum rpm. 1620.5 rpm. 2531 rpm.
∅
775mm –
2070 rpm.
∅
613mm –
2587.5 rpm.
Tractor class 1.4 1.4 2.0
* with overrunning friction clutch
**concerns approximate power demand of the tractor on III gear. On II gear the demand is
decreased about 20%.
Operator’s manual
Front drum mower
K2BF 210; K4BF 265; K4BF 300
- 3 -
Fig. 1. Data plate
Fig. 2.
The components of the mower
1 – Main frame
2 - Cutting unit
3 - Intersecting axis gear
4 - Drum
5 - Suspension frame
6 - PTO shaft
7 - Swath disc (K4BF 265, K4BF 300)
8 - Safety guard
9 - Data plate
10 - Safety curtain
1 2
3
4
56
7
8
9
2
35
8
8
4
1 2
593
2
8
35
6
10
10
8
10
8
35
6
8
72 10
102
3
9
5
8
1
4
Kosiarka czterobębnowa Z 010/7
Kosiarka dwubębnowa Z 010/8
Kosiarka czterobębnowa Z 007
K4BF 265
K2BF 210
K4BF 300
Operator’s manual
Front drum mower
K2BF 210; K4BF 265; K4BF 300
- 4 -
Fig. 2. Cutting unit
2.2. Design and working principle
(description of fig. 2)
The drive on the mowing saucers is transmitted from tractor’s PTO through PTO shaft
(pos. 6), intersecting axis gear (pos. 3) and the gearbox set mounted inside the main frame (pos. 1).
The cutting unit (pos. 2) (shown on fig. 3) consists of drums (pos. 4) with mowing saucers
and knives. These parts are connected to the suspension frame (pos. 5) with mower’s triangle,
which is used to mount the mower on the tractor’s triangle, connected to tractor’s front 3-point
linkage.
For transport the mower is lifted by the tractor’s linkage.
On the mower’s main frame (pos. 1) there are swath discs (pos. 7) which are used to adjust
the swath width (1,2 – 1,6 m).
Over the cutting unit, there is a safety guard (pos. 8) with safety curtain, fastened to the main
frame.
2.3. Proper use
SaMASZ front drum mower is designed for mowing standing grass in meadows and in stone
free fields. It is a machine for hay and green fodder production.
CAUTION:
Use of the mower for other purposes than the above mentioned is
forbidden.
Well-proven design with thousands of machines in regular use in many countries and quality
materials ensure high durability and reliability of SaMASZ mowers.
Talerz roboczy
Nóż
Talerz ślizgowy
Pierścień dystansowy
58 mm
Śruby mocujące M10x25
Talerz oporowy
Trzymak nożowy
Rama główna
Zespół pionu
Bęben
Main frame
Suport saucer
Knife holder
Drum
Mowing saucer
Bolt M10x25
Distance ring
Sliding saucer
Knife
Vertical team
Operator’s manual
Front drum mower
K2BF 210; K4BF 265; K4BF 300
- 5 -
2.4. Standard equipment and spare parts:
The mowers are sold with the following standard equipment:
warranty card,
operator’s manual with spare parts list,
cutting knives: additional set,
mounting lever for quick knife changing,
holders for warning plate and lights.
PTO shaft with friction and overrunning clutch (in the order give the type of PTO shaft
according to fig. 5) (extra payment),
Optional extra equipment:
warning plates with combined lights and reflectors,
warning triangle,
tractor’s triangle.
Tab. 2. PTO shafts for SaMASZ front drum mowers. Manufacturer - Bondioli & Pavesi
Mower PTO shaft
Symbol Moment Power L
nom
Notes
K4BF – 2.65 m 8G4N086CE007001 540 Nm 41 kM
(30 kW) 1195 [mm]
OET
K2BF
– 2.10 m
8G4N086CE007002 WET
K4BF – 3.00 m
OET - Eastern European Tractors, WET - Western European Tractors
Fig. 4. PTO shaft. PTO shaft lubrication points
The PTO shaft must be purchased along with the mower, because using PTO shaft without
friction and overrunning clutch makes the warranty invalid.
WET
OET
Symbol PTO:
8G4N086CE007002
Symbol PTO:
8G4N086CE007001
Fig. 5. Choosing PTO shaft according to tractor’s PTO rpm direction (Tab. 1)
turn right
overload clutch
mounted to
a tractor
unidirectional
clutch
mounted to
a mower
Operator’s manual
Front drum mower
K2BF 210; K4BF 265; K4BF 300
- 6 -
Use PTO shaft with overrunning friction clutch. Putting the mower into its nominal rpm
should be slow.
Too frequent overloading (audible sound) of friction clutch may cause its permanent damage
(visible burnt paint on clutch’s surface)
The mower can be adjusted according to tractor’s PTO rpm direction. Generally, the mower is
adjusted to work with WET tractors with right PTO rpm direction (looking from the operator). To
adjust the mower to work with left PTO direction (OET tractors), please do the following:
Mower K4BF 210; K4BF 265; K4BF 300:
- remove intersecting axis gear (Tab. 1 pos. 14 – mower K2BF 210; tab 1 pos. 16 – mower
K4BF 265; tab. 1 pos. 17 – mower K4BF 300) rotate it a 180
o
,
- remove holders (Tab. 3 pos. 1,2 – mower K2BF 210; K4BF 265; K4BF 300) and rotate
them a 180
o
,
- remove the safety guards and (Tab. 5 – mower K4BF 265; K4BF 300) rotate them 180
o
,
- remove left and right guard of the main frame (Tab. 1 pos. 2,3 – mower K4BF 265;
K4BF 300) rotate them a 180
o
and switch their places ,
- remove the swath discs and attach them on the other side of the main frame (Tab. 4 – mower
K4BF 265; K4BF 300).
Well-proven design with thousands of machines in regular use in many countries and quality
materials ensure high durability and reliability of SaMASZ mowers.
3. SAFETY ADVICE
Operation without safety guards as well as with the damaged or raised guards is not allowed
(danger of the stones, etc. being thrown out).
Start mowing only when the tractor’s PTO reaches its normal 1000 rpm.
Nobody is allowed to remain within the danger area of at least 50 m. Particular caution is
necessary when operating near roads and in stoney areas.
The areas to be mowed should be cleared of any hard objects (stones, etc). Large stones should
be removed and small ones rolled in during the spring.
Any maintenance and adjustment work should only be done after the drive has been
disconnected and when the cutting saucers have come to a complete standstill.
Always check mower before starting work, in particular for damaged, missing and/or worn
knives and knife holders. Damaged or worn parts must be replaced.
When driving on public roads always comply with local traffic regulations, especially
concerning warning lights.
When the mower is lifted for repair on the 3-point-hydraulic lift, it should be secured against
falling by a mechanical support or by chain.
Never lift the mower on tractor lift when the drive is on and the cutting saucers are rotating.
The bolts and other fasteners have to be periodically checked and, if necessary, tightened or
replaced. DO NOT work with damaged or worn fasteners.
No passengers or loads are allowed on the machine and tractor during operation and transport.
During transport (even on short distances) the mower should be in its transport position.
During operation of the mower the Regulation of the Farm Ministry and Food Economy
(Rozporządzenie Ministra Rolnictwa i Gospodarki Żywnościowej) from 12-01-1998 dealing
with safety and hygiene during the operation of tractors, machinery, tools andequipment used
for farming (Dz. U. Nr 12/98 poz. 51), should be observed,
Operator’s manual
Front drum mower
K2BF 210; K4BF 265; K4BF 300
- 7 -
CAUTION:
All service and repair operations must be done only after the tractor
engine has been stopped, all rotating parts have come to the complete
standstill and the sliding saucers are on the ground
.
3.1. Warning decals.
CAUTION:
a) all warning decals should be clean and legible,
b) lost or damaged decals must be replaced,
c) please order new decals from your dealer or supplier.
1. N-3
Caution – read the operator’s
manual before putting the mower
into operation!
2. N-4
Caution – while making repairs the
machine must be stopped!
3. N-7
Operating is forbidden when any
person is within the danger area of
50 m!
4. N-1
Be extremely careful when PTO
shaft is rotating!
5. N-2
Caution – cutting knives.
Approach during operation is
forbidden!
6. N-6
Caution – rotating parts
7. N-28 8. P-2
CAUTION:
Mower’s nominal rpm: +5 ÷ -10% tj. 1050 ÷ 900 rpm.
Operator’s manual
Front drum mower
K2BF 210; K4BF 265; K4BF 300
- 8 -
4. TRANSPORT AND WORKING POSITIONS
4.1. Mounting the mower on tractor’s triangle cat. II
CAUTION:
The manufacturer is not responsible for mower‘s damage, if it is
caused by improper mounting.
Unmounting of the mower may cause the following damages:
- bending of mower’s guards by the tractor,
- damage of PTO shaft,
- damage of the gear and other parts of the mower.
During operation check mounting of the mower.
The mower is mounted on the triangle which is connected to the tractor’s front 3-point
linkage (the triangle cat. II is NOT a part of standard equipment – it can be ordered from SaMASZ
as optional extra equipment).
When the triangle is connected to the tractor’s 3-point linkage, adjust it (by means of upper
link) in parallel to the mower’s triangle, lift the 3-point linkage until it locks in, check the space
between (1) triangle’s hook and pawl (2) (fig. 6a), block the hook (1) with cotter pin ∅4 (2)
(fig. 6b), adjust the space between the frame suspension and a rubber safety bumper to about 120
mm (fig. 6), regulate and mount support chains, block them with cotter pins according to 6.3.
Fig. 6. Proper mounting of the mower on tractor’s triangle cat. II
CAUTION:
Different mounting of the PTO shaft in emergency situations (e.g. if
the mower is improperly mounted and secured) may damage PTO
shaft, intersecting axis gear etc.
~ 120 mm
W
b)
3
1 1
2 2
View „W”
A
11
2 2
a)
A-A
A
Adjust the mower in parallel
to the ground by means of
upper link.
Block the hook with cotter
pin. Adjust the space between
the frame suspension and
rubber safety bumper to
about 120 mm
Regulate, mount and block the
support chain. Block the pin.
block
Shafts end with
friction clutch. Shafts end with
overrunning clutch.
Chain
regulating
holes
Operator’s manual
Front drum mower
K2BF 210; K4BF 265; K4BF 300
- 9 -
4.2. Adjusting the clearance between triangle’s hook and lock
After the mower has been mounted and lifted and the clearance between triangle’s hook and
lock has more than 1 mm (fig. 6a), please do the following:
Element A
Fig. 7. Adjusting the lock
loosen the lock nut (1),
by means of the bolt (2) adjust the clearance between triangle’s hook and lock (element A
fig. 7),
block the bolt 2 with a nut 1.
4.3. Adjusting the length of support chains
To adjust the length of support chains properly, please do the following:
lift the mower on the tractor’s lift until the space between the frame suspension and a rubber
safety bumper reaches about 12 cm (fig. 6),
tighten the chains and check where to block them,
lift the mower higher and block the chains with pins,
lower the mower until the chains tighten,
check the space between the frame suspension and a rubber safety bumper. If the space is lower
or higher than 12 cm, correct it (fig. 6 and fig. 7).
4.4. Preparing the mower for transport
To put the mower into the transport position, please do the following:
lift the mower with tractor hydraulic lift,
lift the side safety guards (fig. 8),
to meet safety precautions concerning transport on the public roads in Poland the mower should
be equipped with the following devices – portable warning-light plates, to be mounted on both
sides of mower side guards in their holders (fig. 8),
when driving on public roads always comply with local traffic regulations, especially
concerning warning lights,
when maneuvering pay particular attention to the space around the tractor-mower set.
a
Równoległość
3
1
2
Lock
regulation
Chain
regulating
holes
Trójkąt Mower’s
triangle
Tractor’s triangle
A
Operator’s manual
Front drum mower
K2BF 210; K4BF 265; K4BF 300
- 10 -
Fig. 8. Front drum mower in its transport position
4.5. Mounting PTO shaft
When connecting PTO shaft between tractor and mower make sure, that external guard tube
of the shaft is on the tractor’s side.
The PTO shaft plastic guards have to be secured by fastening their small chains to immovable
parts of tractor and mower.
WARNING:
Before operation, please comply with PTO shaft’s operator’s manual.
In case of any PTO shaft’s damage when using the shaft not according
to its manual company SaMASZ does not bear the responsibility for
warranty claim’s refusal by shaft’s manufacturer. It is forbidden to
work a long time with overloaded shaft – max. 10 seconds.
WARNING:
Check the minimum and maximum length of the PTO shaft.
Overlapping of the tubes must be at
1
/
3
of the length of the tubes during
operation. If the attached PTO shaft does not meet these conditions, ask
SaMASZ to replace it. If the PTO shaft is damaged due to inappropriate
length the warranty will be lost.
WARNING:
Operate machinery only with the articulated telescopic shafts
designated for use with that machinery. Before starting work check if
all the covers (tractor, machinery and shaft) are in place and
functioning. Damage or lost elements must be replaced with original
spares. Check weather the articulated telescopic shaft is properly
installed. Never get close to rotating parts it could result in injury or
death. During servicing of the shaft or the machine the engine and
the power take-off of the tractor must be turned off. Before operating
any machinery carefully read the operating manuals of the shaft and
the machine.
Operator’s manual
Front drum mower
K2BF 210; K4BF 265; K4BF 300
- 11 -
WARNING:
PTO shaft’s end with friction clutch should be mounted to the tractor
and with overrunning clutch to the mower.
4.6. PTO shaft’s length adjustment
In case there is a necessity to shorten PTO shaft, please make it according to the drawings 9a
and 9b. Plastic cover of the shaft is shortened the same way.
Fig. 9a) Shorten the same length of inner and outer tube Fig. 9b) Shorten the same length of inner
and outer plastic cover (the same length as
tubes)
4.6.1. Preparing the mower for work
Before the work begins, please carry out the procedures included in the previous chapters and
after that the mower is considered to be ready for work, and then:
lower the mower until the sliding saucers come into contact with the ground (fig. 10),
slowly engage the PTO clutch and wait until the cutting unit reaches its rated speed,
engage tractor gear and drive slowly into the grass-field.
Support chain holds up tractor’s hydraulic cylinders and maintains mower’s level. It causes
lower tear of sliding saucer hub.
CAUTION:
If the mower is improperly adjusted to the ground (fig. 10), it leads to
faster wear of the sliding saucer hub and knives.
incorrect correct incorrect
Fig. 10. Adjust the drums level with the drum
ADJUSTING THE MOWER FOR MOWING
Operator’s manual
Front drum mower
K2BF 210; K4BF 265; K4BF 300
- 12 -
Klucz specjalny
Trzymak nożowy
Nożyk
Talerz ślizgowy
Talerz roboczy
5. MOUNTING AND ADJUSTMENTS
5.1. Mounting and timing of the knives
Fig. 11. Timing of the knives on the mowing saucers
Fig. 11. Mounting blades
CAUTION:
The cutting edges of the new knives should be directed towards ground.
5.2. Adjusting the cutting height
The mower has a factory-set cutting height of 58 mm. The cutting height can be adjusted by
removing a distance ring (spacer) as show in Fig. 13. After removing a new cutting height of
50 mm is achieved. By putting one additional spacer over the support saucer a cutting height of
66 mm is obtained. Additional spacers are available (optional extras).
Mounting lever
Knife
Knife holder
Mowing saucer
Sliding saucer
Kosiarka czterobębnowa Z 007
K4BF 300
K4BF 265
Kosiarka dwub
ębnowa Z 010/8
K2BF 210
Operator’s manual
Front drum mower
K2BF 210; K4BF 265; K4BF 300
- 13 -
Fig. 13. Adjusting the cutting height by fitting or removing the distance ring
CAUTION:
When mounting additional distance rings longer bolts - M10x35 must
be used and tightened to a torque of 55 Nm.
5.3. Maintenance and service
Checking the knives and knife holders
All knives should have the same lengths and weights. Always check mower before starting
work for damaged, missing and/or worn knives. Replace knives, if necessary, only in sets. Make
sure all knives in a set are of the same length and weight.
The knife holders must not be damaged or deformed and the knife holder pin, on which
the knife is pivoting, shouldn’t be worn down by more than 50 % of its cross-section (Fig. 14).If
the knife holder pin is worn too much and/or the knife holder is worn or deformed on the outside
edges, please replace the knife holder immediately. The riveting of the pin in the knife holder must
be checked for safety and quality too. If the riveting is loose, replace the knife holder.
Fig. 14. Permissible wear of knife holders
CAUTION!
Operation with worn and/or damaged knife holder is forbidden. It may
lead to throwing out of the knife.
5.3.1. Daily maintenance
Everyday after work please carry out the following maintenance:
remove grass and mud,
clean the mower each day after working, especially between discs and the cutterbar, because
grass with mud may damage bearings in the disc module,
check all visible units and parts and their connections; tighten all loose bolts and nuts and
replace all damaged and/or worn parts with new genuine ones,
grease PTO shaft tubes with STP grease,
if necessary, lubricate the parts and units according to lubrication instruction.
Knife holder pin
Sliding saucer
Support saucer
Fastening bolts
Distance ring
58 mm
50 mm
Standard version Reduced version
Operator’s manual
Front drum mower
K2BF 210; K4BF 265; K4BF 300
- 14 -
5.3.2. After-season maintenance
At the end of the season the mower should be cleaned, washed and dried. Carefully grease
unpainted surfaces and 3-point linkage pins.
After that the following work should be carried out:
remove any traces of rust and paint the area affected.
check lubrication of intersecting axis gear – fig. 15.
if leaks occur and the plastic cap of air-escape valve is damaged, replacement of the sealing
under gear trough cover and of the valve cup are recommended. If water is discovered in
the oil, it must be changed, otherwise the gears, bearings and shafts could be damaged. Put
the replacement sealing carefully into place and tighten cover screws uniformly.
6. LUBRICATION INSTRUCTION
Lubrication scheme shown in Figure mower:
Symbol Oil type
Oil Transol 680 - 1000
Gear oil Transol or Hipol
Fig. 15. Lubrication points
6.1. Main frame.
The oil level is to be checked periodically through the air-escape valve. The oil level should
be 15 to 20 mm (about ¾ inch) above the bottom. Oil capacity in the gearbox for all types of
the mowers is 5 l. If the checked oil level is low, please check and eliminate any leaks and fill up to
the oil level required.
6.2. Intersecting axis gear.
Everyday before starting work please check the oil level and if needed please refill after
having removed the vent on the top of the gear. The oil level can be checked through the check
opening on the side of the gear. Please refill the oil until it is visible in the check opening. The oil
level: about 1 l.
CAUTION:
The above instructions should be strictly followed. If the mowing
saucers rotate loosely, do not worry about the high intersecting axis
gear temperature; after long working time it may reach even 60 - 80
o
C.
Operator’s manual
Front drum mower
K2BF 210; K4BF 265; K4BF 300
- 15 -
7. DEFECTS AND THEIR REPAIRS
CAUTION:
Before disassembly the mower should be disconnected from the tractor
.
7.1. Disassembly
Before starting any repair or service the mower should be cleaned and any grass or dirt
removed. Carefully check nuts and bolts for correct tension and the pins for wear. Replace as
necessary.
7.2. Scrapping
If the mower cannot be repaired anymore, it should be withdrawn from use.
For this purpose oil from gear trough should be drained and delivered to a proper waste
treatment company. Clean the mower parts, dismantle and dispose properly of all plastic parts.
After that, the mower could be sold to breaker’s yard.
8. DISASSEMBLY AND WITHDRAWAL FROM USE
Defect Reason Repair
Mower stops mowing
Rpm too low Speed up the rpm
Worn knives Replace knives
Dirt between knife holder and the
mowing saucer – mud, grass
leftovers etc. – knife hidden
Remove dirt-
-pull out the knife
Tractor’s PTO rpm is too low,
even though there is high engine
rpm
Check the PTO tractor service
Knives are missing Knife holder damaged (bent). Replace knife holder
Mower leaves uncut grass
stripes between the
mowing saucers
Too high PTO rpm Reduce PTO rpm
Too low PTO rpm Speed up the rpm
Operator’s manual
Front drum mower
K2BF 210; K4BF 265; K4BF 300
- 16 -
9. WARRANTY CARD
FRONT DRUM MOWERS:
The product quality has been checked and meets the required standards and regulations. The mower
is permitted for use
CAUTION:
A warranty card without the required information or with corrected or
illegible information – is invalid.
10. WARRANTY TERMS.
10.1. Warranty terms procedures
1. The manufacturer guarantees its products againts faults in materials or production.
2. The warranty period is for a two years from the date of sale to the purchaser, stated above.
3. Any faults or malfunctions of the mower become apparent within a 12 month period of the date
of purchase will be corrected free of chargé at the buyer’s residence.
4. Claims for replacement a defective product by the new one are proceeded by the manufacturer
within 14 days.
5. The following cases are not covered by warranty:
a) use for any other purpose than those described in the operator’s manual,
b) accidental damage,
c) wearing parts, e.g. mowing saucer, sliding saucer, knife holders, intersecting axis
gears and parts inside the gearboxes, bushings and sliding elements, joints, knives,
bearings, lower hubs, rubber-metal fenders, safety curtains, connective elements,
etc. Those repairs can be done only at the buyer’s expense.
6. The purchaser bears the costs of technical estimation – when the manufacturer finds that
a claimed product is free of defects and a technical report will confirm that.
7. The manufacturer has the right to cancel a warranty in the following cases:
a) interference of the interior of the mower, changes of its mechanical design or
intentional damages,
b) damage caused by accidents or other events, for which the warrantor is not
responsible,
Serial number
Date of manufacture
Manufacturer’s stamp
QC signature
Date of purchase
Dealer’s stamp
Dealer’s signature
Operator’s manual
Front drum mower
K2BF 210; K4BF 265; K4BF 300
- 17 -
c) lack of required inscriptions or arbitrary inscriptions in the warranty card,
d) use of the mower not in accordance with operator’s manual or for incorrect purpose,
CAUTION:
Please ask your dealer to fill the warranty card with proper dates,
stamps and signature when purchasing. Lack of this important
information may cause cancel of warranty.
CAUTION:
Every after-warranty repair can be done against payment by the repair
shops authorised by the dealer. Authorisation is a duty of your dealer.
CAUTION:
The manufacturer reserves the right to alter technical design and
specification without prior notice and without liability.
10.2. Warranty repairs record
Repair description and changed spare parts:
Date, stamp and signature of repair shop.
Date, stamp and signature of repair shop.
Date, stamp and signature of repair shop.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
SaMASZ K2BF 210 is a front drum mower designed for mowing standing grass in meadows and stone-free fields. It has a working width of 2.10 m and is equipped with 8 knives. The mower is powered by a tractor's PTO and has a cutting speed of 90.8 m/s. It can be used to mow grass with a height of up to 10 cm and can achieve a working capacity of ~2.4 ha/h. The mower is also equipped with a safety guard and curtain to protect the operator from debris.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
