2. Transmitter
  3. iGAZEREKIT-UL
iGAZEREKIT-UL

Transmitter iGAZEREKIT-UL Product information

  • Hello! I've reviewed the Safety Device Wiring Manual for the NICE 1050 US Board, including its safety features for IN1, IN2, and UL/EDGE connections. I understand the programming steps for Pulse Safety and Entrapment, along with the requirements for monitored devices and the handling of obstructions. I'm ready to answer any questions you have about this product and its setup.
  • What is the minimum firmware version to use Pulse Safety and Pulse Entrap options?
    How many monitored devices can I connect per input at In1 or In2?
    What will happen if no monitored device is connected to the 1050 US board?
    What happens when an obstruction is detected during the close operation using Pulse Safety?
Safety Device Wiring Manual
NICE® 1050 US BOARD
Entrapment and Safety Protection
NOTE:
In1 LED glows red
when aligned
Programming for IN1 (terminal # 16)
1. Press "Functions"
2. Scroll down to "3. Auxiliary IO"
3. Press "OK"
4. "In Aux1" is now visible
5. Press "OK"
6. Scroll up to either "Pulse Safety" or
"Pulse Entrap"
7. Press "OK"
8. Connect 300Hz Pulse Monitored
Safety Device
Programming for IN2 (terminal # 18)
1. Press "Functions"
2. Scroll down to "3. Auxiliary IO"
3. Press "OK"
4. Scroll up to "In Aux2"
5. Press "OK"
6. Scroll up to either "Pulse Safety" or
"Pulse Entrap"
7. Press "OK"
8. Connect 300Hz Pulse Monitored
Safety Device
Programming for UL/EDGE (terminal #28)
1. Press "Functions"
2. Scroll down to "9. Advanced Settings"
3. Press "OK"
4. Scroll down to "UL Input"
5. Press "OK"
6. Scroll to either "Analog" or "Digital" setting
(depending on edge type)
- Analog (8.2kΩ) - Digital (NC/NO)
7. Press "OK"
8. To exit the configuration menu press “Display”, then press “OK”
IN1
IN2
EDGE
NOTES:
• "Pulse Safety" and "Pulse Entrap"
options are only available on 1050US
boards. (FW: 01.06.00 or higher)
• Only one monitored (Pulse) device may
be connected per input at In1 or In2.
• At least one monitored device must be
connected properly to 1050 US boards. A
"BlueBus Error" will result if this require-
ment is not met.
Used with permission of NICE®. All graphics, language and layouts are copyright protected by NICE®. NICE® assumes no responsibility for the
accuracy of the information provided by Transmitter Solutions. The Transmitter Solutions products listed have not been treated nor listed by NICE® as
being UL Compliant for their system. All testing has been conducted by Transmitter Solutions.
PULSE SAFETY:
When an obstruction is detected during the close opera-
tion of the gate, the gate will reverse fully open and will
re-close when the auto-timer has timed out.
ANALOG (UL/EDGE):
When an obstruction is detected during either the open or
close operation of the gate, the gate will reverse for 2 seconds
and enter a soft shutdown until an open or close command is
given.
If a second obstruction is detected during the same open/close
cycle, the gate will enter a hard shutdown and enter alarm
mode.
PULSE ENTRAPMENT:
When an obstruction is detected during either the open
or close operation of the gate, the gate will reverse for 2
seconds and enter a soft shutdown until an open or
close command is given.
If a second obstruction is detected during the same
open/close cycle, the gate will enter a hard shutdown
and enter alarm mode.
470Ω Resistor
PULSE SAFETY - IN1
(Terminal #16)
IGAZEREKIT-UL
TRANSMITTER SOLUTIONS
PHOTO EYE
TRANSMITTER SOLUTIONS
iGAZE RE UL 10kΩ KIT
+
C1
12/24
NC1
NO1
C2
NC2
NO2
Test 1
Test 2
Test C
−
iGAZER23-2WC or
iGAZER50-2WC
Nice 1050 Board UL-325
IN 1
GND
IN 2
GND
24 V
GND
16 17 18 19 20 21
470Ω Resistor
PULSE ENTRAPMENT - IN2
(Terminal #18) TRANSMITTER SOLUTIONS
PHOTO EYE
iGAZER23-2WC or
iGAZER50-2WC
Nice 1050 Board UL-325
IN 1
GND
IN 2
GND
24 V
GND
16 17 18 19 20 21
ANALOG (8.2k)
UL/EDGE
(Terminal #28)
Nice 1050 Board UL-325
EDGE/UL
GND
EXIT
GND
FIRE
GND
28 29 30 31 32 33
OPEN
STOP
CLOSE
GND
12 V
OPEN
34 35 36 37 38 39
CLOSE
GND
40 41
/