Lit. No. 85299, Rev. 00 1 January 15, 2017
PARTS LIST
85264 Rubber Defl ector Kit
Item Part Qty Description Item Part Qty Description
1852621Rubber Defl ector 3 84541 2 Retainer Bar – Outside
2 84542 1 Retainer Bar – Center ns 84673 1 Bolt Bag
84673 Bolt Bag
4 12 5/16-18 x 1-1/4 Hex Cap Screw G5 6 12 5/16-18 Hex Locknut GB
5 12 5/16 Flat Washer
ns = not shown G = Grade
85264 – 7'-2" & 6'-8"
Straight Blades
RUBBER DEFLECTOR KIT
Parts List & Installation Instructions
A DIVISION OF DOUGLAS DYNAMICS, LLC
Western Products
PO Box 245038
Milwaukee, WI 53224-9538
www.westernplows.com
1
2
3
3
4
5
6
85264 RUBBER DEFLECTOR KIT
Lit. No. 85299, Rev. 00 2 January 15, 2017
2. Align the defl ector on the blade, matching up
the holes in the defl ector with the holes in the
moldboard.
3. On 6' 8" blades, the defl ector extends beyond the
ends of the blade. Trim excess length from both
ends of defl ector and retainer bars as shown.
4. Attach the retainer bars and defl ectors to the
blade using the supplied 5/16" x 1-1/4" cap screws,
washers, and locknuts. Tighten fasteners until the
retainer bars are tight against the defl ector.
5. Touch up the paint on the ends of the retainer
bars, using WESTERN Black Enamel touch-up
paint (not included).
5/16" x 1-1/4"
Cap Screw
5/16"
Flat Washer
5/16"
Locknut
Copyright © 2017 Douglas Dynamics, LLC. All rights reserved. This material may not be reproduced or copied, in whole or in part, in any
printed, mechanical, electronic, fi lm or other distribution and storage media, without the written consent of Western Products. Authorization to
photocopy items for internal or personal use by Western Products outlets or snowplow owner is granted.
Western Products reserves the right under its product improvement policy to change construction or design details and furnish equipment when
so altered without reference to illustrations or specifi cations used. Western Products or the vehicle manufacturer may require or recommend
optional equipment for snow removal. Do not exceed vehicle ratings with a snowplow. Western Products offers a limited warranty for all
snowplows and accessories. See separately printed page for this important information. The following are registered (®) or unregistered (™)
trademarks of Douglas Dynamics, LLC: UltraMount® 2, WESTERN®.
Printed in U.S.A.
INSTALLATION INSTRUCTIONS
1. Park the vehicle on a smooth, level, hard surface,
such as concrete. Lower the blade to the ground,
and turn the control OFF. Turn the vehicle ignition
to the "OFF" position and remove the key.
CAUTION
Use standard methods and practices
when attaching snowplow and installing
accessories, including proper personal
protective safety equipment.
CAUTION
Read this document before installing the
rubber defl ector kit.
WARNING
Do not exceed GVWR or GAWR, including
blade and ballast. The rating label is found on
the driver-side vehicle door cornerpost.
CAUTION
See your WESTERN® outlet/website for
specifi c vehicle application recommendations
before installation. The Quick Match selection
system has specifi c vehicle and snowplow
requirements.
Trim excess length.
-
1
-
2
Western Rubber Deflector Kit #85264 Parts list
- Type
- Parts list
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Western ProPlow Blade 60381/60390/60308/60655/62400/62450; AQ&L 63568; Hydraulics 56365;Headlamp 61540/61550 Installation guide
-
-
Western POLY PRO-PLOW Series 2 Installation Instructions Manual
-
-
-
-
-
-
-