LED One LOC-4FTT8AB T8 LED Tube Installation guide

Brand
LED One
Model
LOC-4FTT8AB T8 LED Tube
Type
Installation guide

LED One LOC-4FTT8AB T8 LED Tube is a versatile and energy-efficient lighting solution suitable for various indoor applications. With its wide voltage range of 120-277VAC, this tube can be used in both residential and commercial settings. It operates at a frequency of 50/60Hz, providing stable and flicker-free illumination.

The LOC-4FTT8AB consumes only 12W of power, making it an eco-friendly and cost-effective alternative to traditional fluorescent tubes. It emits a bright light output of 189mA, ensuring ample illumination for tasks and general lighting needs. The tube has a length of 4 feet, making it suitable for standard fluorescent tube fixtures.

LED One LOC-4FTT8AB T8 LED Tube is a versatile and energy-efficient lighting solution suitable for various indoor applications. With its wide voltage range of 120-277VAC, this tube can be used in both residential and commercial settings. It operates at a frequency of 50/60Hz, providing stable and flicker-free illumination.

The LOC-4FTT8AB consumes only 12W of power, making it an eco-friendly and cost-effective alternative to traditional fluorescent tubes. It emits a bright light output of 189mA, ensuring ample illumination for tasks and general lighting needs. The tube has a length of 4 feet, making it suitable for standard fluorescent tube fixtures.

Phone: (844) LEDONE6 | Fax: 1-510-217-9461 | Web: www.ledonecorp.com
LOC-4FTT8AB Installation Guide
ELECTRICAL RATINGS: INPUT RATINGS
• Voltage: 120-277VAC
• Frequency: 50/60Hz
• Current: 134mA / 189mA
• Wattage: 12W / 17W
• Tube Length: 4 foot
ENVIRONMENTAL CONDITIONS:
The T8 LED tube cannot be installed in rain, wet areas, dusty areas, flammable areas or combustible environments. Please confirm
the light fixture meets the level of protection requirements if necessary.
INSTALLATION REQUIREMENTS:
The installation should be done by a licensed electrician. If the tube is Type B, please take the ballast and starter out of the light
before installing. The operating temperature is -20 ° C~ + 40 ° C.
INSTALLATION INSTRUCTIONS:
The T8 tube can only work with the matched voltage.
Type A (ballast compatible): Please check the connection instruction image as follows. You MUST check the ballast compatible
listing before installing Type A with a ballast.
• Step 1: Turn off the power before installing.
• Step 2: Take down the fluorescent lamp.
• Step 3: Install the LED tube.
Type B (ballast by-pass) (single end): To replace the traditional fluorescent tube, please reconnect the electric circuit. Please
check the connection instruction image as follows:
• Step 1: Turn off the power before installing.
• Step 2: Take down the fluorescent lamp, cut off the power line that is connected with the ballast and starter.
o Note: Ballast and starter must be retained in place.
Phone: (844) LEDONE6 | Fax: 1-510-217-9461 | Web: www.ledonecorp.com
LOC-4FTT8AB Installation Guide
• Step 3: Install the LED tube and make the electrical connection.
More than one set installation image:
• Step 4: Affix the field applied label to the light fixture and install the tube. The tube has single end wiring connection. There
are descriptions of connections for the source of electrical supply to the lamp pins. Please make sure no wiring connection
on the other end.
OR
OR
Phone: (844) LEDONE6 | Fax: 1-510-217-9461 | Web: www.ledonecorp.com
Type B (ballast by-pass) (double ended): To replace the traditional fluorescent tube, please reconnect the electric circuit. Please
check the connection instruction image as follows:
• Step 1: Turn off the power before installing.
• Step 2: Take down the fluorescent lamp, cut off the power line that is connected with the ballast and starter.
o Note: Ballast and starter must be retained in place.
• Step 3: Install the LED tube and make the electrical connection.
More than one set installation image:
Phone: (844) LEDONE6 | Fax: 1-510-217-9461 | Web: www.ledonecorp.com
• Step 4: Affix the field applied label to the light fixture and install the tube. The tube has double ended wiring connection.
WARNINGS:
• Check if the product is in good condition before installation.
• You MUST check the ballast compatible listing before installing Type A with a ballast.
• The LED tube should not be knocked down or replace with a driver randomly.
• Product should not be placed in wet areas, high temperatures, flammable or combustible environments. They should be in
a cool, dry environment.
• Risk of fire or electric shock WARNING: The electrical rating of this products is 120-277Vac. The installer must determine
whether they have 120-277V at the luminaire before installation.
• Risk of fire or electric shock WARNING: Installation requires knowledge of luminaries’ electrical systems. If you are not a
qualified electrician, do not attempt installation. Contact a qualified electrician.
• Risk of fire or electric shock WARNING: Install this product only in the luminaires that have the construction features and
dimensions shown in the photographs/drawings.
• Do NOT make or alter any open holes in the enclosure of wiring or electrical components during installation.
• NOT suitable for enclosed fixtures.
• To prevent wiring damage or abrasion, do NOT expose wiring to edges of sheet metal or other sharp objects.
• To avoid potential fire or shock hazard, do NOT use the retrofit kit in luminaires employing shunted bi-pin lamp holders.
o Note: Shunted lamp holders are found only in fluorescent luminaires with instant-start ballasts. Instant start
ballasts can be identified by the words “Instant Start” or “I.S.” marked on the ballast. This designation may be in
the form of a statement pertaining to the ballast itself or may be combined with the marking for the lamps with
which the ballast is intended to be used. For example, F40T12/IS. For more information, contact the LED luminaires
retrofit kit manufacturer.
• Installers should not disconnect existing wires from the lamp holder terminals to make new connections at lamp holder
terminals. Instead, installers should cut the existing lamp holder leads away from the lamp holder and make new electrical
connections to the lamp holder lead wires by employing applicable connectors.
LOC-4FTT8AB Installation Guide
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

LED One LOC-4FTT8AB T8 LED Tube Installation guide

Brand
LED One
Model
LOC-4FTT8AB T8 LED Tube
Type
Installation guide

LED One LOC-4FTT8AB T8 LED Tube is a versatile and energy-efficient lighting solution suitable for various indoor applications. With its wide voltage range of 120-277VAC, this tube can be used in both residential and commercial settings. It operates at a frequency of 50/60Hz, providing stable and flicker-free illumination.

The LOC-4FTT8AB consumes only 12W of power, making it an eco-friendly and cost-effective alternative to traditional fluorescent tubes. It emits a bright light output of 189mA, ensuring ample illumination for tasks and general lighting needs. The tube has a length of 4 feet, making it suitable for standard fluorescent tube fixtures.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents