Astria Fireplaces Mission Instruction Sheet

Brand: Astria Fireplaces

Model: Mission

Type: Instruction Sheet

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

KIT CONTENTS

• (1) ea. High Density Foam Roller

• (1) ea. Roller Handle

• (1) ea. Paint Tray

• (1) 32-oz. Can Firebrick Stain

REQUIRED TOOLS

• Paint Lid Opener or Flat Screwdriver

• Wire Brush (pictured at right)

• Broom or Vacuum

• Clean Rags and Water

• Chemical-resistant Gloves

• Safety Glasses

ADDITIONAL REQUIRED TOOLS IF STAINING

PREVIOUSLY INSTALLED FIREBRICK OR GROUT:

• Bristle Paint Brush

• Wedge-shaped, High-density Foam Brush

ADDITIONAL RECOMMENDED TOOLS

IF REMOVING OLD PAINT OR STAIN:

• NIOSH-approved Respirator

• HEPA Vacuum

HEARTH PRODUCTS

KITS AND ACCESSORIES

P/N 506019-65, Rev. A

01/2017 REFRACTORY FIREBRICK STAIN KIT

APPLICATION INSTRUCTIONS FOR REFRACTORY FIREBRICK STAIN

FOR USE ON ALL IHP WHITE REFRACTORY BRICK LINER PANELS

APPLICATION INSTRUCTIONS

NOTICE:

• READ ALL THE STEPS BEFORE STARTING THE APPLICATION.

• THESE INSTRUCTIONS MUST BE LEFT WITH THE APPLIANCE.

• ALL WARNINGS, PRECAUTIONS, AND INSTRUCTIONS IN THE

INSTALLATION INSTRUCTIONS AND CARE AND OPERATION

MANUALS PROVIDED WITH THE APPLIANCE ALSO APPLY TO

THESE INSTRUCTIONS.

• IF YOU ENCOUNTER ANY PROBLEMS, NEED CLARIFICATION OF

THESE INSTRUCTIONS, OR ARE NOT QUALIFIED TO PROPERLY

INSTALL THIS KIT, CONTACT YOUR LOCAL DISTRIBUTOR OR DEALER.

Step 1. Prepare masonry surfaces.

NOTE: Firebrick and mortar must be COMPLETELY DRY before

applying stain. Any moisture could affect stain adhesion after curing.

If you scrape, sand, or remove old paint from any surface, you may

release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN

CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY

IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE.

Wear a NIOSH-approved respirator to control lead exposure. Carefully

clean up with a wet mop or HEPA vacuum. Before you start, ﬁ nd out

how to protect yourself and your family by contacting the National

Lead Information Hotline at 1-800-424-LEAD or www.epa.gov.

WARNING

LIFTING HAZARD.

SINGLE-PERSON LIFT COULD

CAUSE INJURY. USE ASSISTANCE

WHEN MOVING OR LIFTING.

Wedge-shaped Foam Brush

(not included)

GENERAL INFORMATION

This permanent, high-temperature refractory ﬁ rebrick stain is designed

and approved for use on all Innovative Hearth Products (IHP) refractory

brick liner panels and all new and previously used masonry ﬁ replaces.

Using this product in any other application is NOT approved.

Refractory ﬁ rebrick stain can be used to give a ﬁ replace a unique

look, showcase a large or decorative ﬁ replace, or change an existing

ﬁ rebrick color to enhance a room’s color scheme.

This kit includes enough stain to cover four (4) IHP refractory brick

liner panels with at least two (2) coats of stain.

This kit also includes sufﬁ cient tools for staining semi-smooth,

uninstalled refractory ﬁ rebrick. Staining grout lines, rough or uneven

masonry, or installed ﬁ rebrick requires the use of additional tools,

such as a wedge-shaped, high-density foam brush and/or a bristle

paint brush (pictured above; not included).

NOTE: Results are not guaranteed and will vary depending on

individual application methods, type and condition of ﬁ rebrick

and mortar, and environmental conditions.

Bristle Paint Brush

(not included)

Wire Brush (not included):

Brush all surfaces with

a wire brush, and then

sweep or vacuum dust.

Included in Kit

This product contains chemicals known to the State of California

to cause cancer and birth defects or other reproductive harm.

Figure 1

1.1. [FOR UNINSTALLED REFRACTORY PANELS]: Using at least two

people, lay refractory panels face up on a clean, level surface that

has been covered to protect it from possible drips or spills.

1.2. [FOR ALL APPLICATIONS]: Brush all ﬁ rebrick (and any other

masonry or mortar to be stained) with a wire brush to remove all

soot and debris and prepare surfaces for stain (Figure 1, below).

1.3. Sweep or vacuum all surfaces to remove excess dust.

Obtain and read Material Safety Data Sheet before using.

See web links listed on reverse side.

WARNING

DO NOT TRANSFER STAIN TO UNLABELED CONTAINER.

KEEP OUT OF REACH OF CHILDREN.

WARNING

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

FIRST AID

• In case of EYE contact, immediately wash with plenty of water for

at least 15 minutes, and get immediate medical attention.

• For SKIN, wash thoroughly with soap and water.

• If affected by INHALATION of vapor or spray mist, get fresh air.

• If SWALLOWED, get immediate medical attention.

For additional information, obtain the MSDS (MATERIAL SAFETY

DATA SHEET) from the web site listed below.

IHP • REFRACTORY FIREBRICK STAIN • APPLICATION INSTRUCTIONS

Step 3. Apply stain.

3.1. Dip the roller into the stain, and then roll it over the upper part of

the paint tray several times to remove excess stain. To prevent

dripping, do not overload roller with stain.

3.2. Using very little pressure, start rolling a VERY THIN coat of stain

(Figure 2, below). Wipe any drips with a clean rag and water

before stain dries.

3.3. Repeat Steps 3.1 and 3.2 until the entire refractory panel is

covered with a THIN, EVEN COAT of stain.

3.4. If applying another coat of stain to the same panel, let stain dry

for at least 30 minutes between coats.

3.5. Repeat these steps for each refractory panel.

3.6. When all stain has been applied, allow stain to dry for at least

24 hours before installing refractory panels or building a ﬁ re.

Wait at least 30 minutes between coats and at least

24 hours before installing refractories or building a ﬁ re.

Masonry with different porosities may require heavier

application or longer drying times.

P/N 506019-65 REV. A 01/2017

IHP reserves the right to make changes at any time, without notice, in design, materials,

speciﬁ cations, and prices, and also to discontinue colors, styles, and products. Consult

your local distributor for ﬁ replace code information.

1508 Elm Hill Pike, Suite 108, Nashville, TN 37210

Step 2. Prepare materials.

2.1. Attach the foam roller to the handle.

2.2. Vigorously shake the stain can for 30 seconds.

2.3. Using a paint lid remover or ﬂ at screwdriver, remove the lid from

the stain can, and pour a small amount of stain into the tray.

2.4. Have a clean rag and water available to wipe any drips.

2.5. Before applying stain, read "APPLICATION TIPS," below.

APPLICATION TIPS

• The wet color of the stain is not indicative of the end result

color. The stain will dry darker or more opaque than it

appears when ﬁ rst rolling it on; therefore, it is best to apply

ONE THIN COAT and wait for it to dry completely before

deciding whether to apply additional stain.

• For a semi-transparent ﬁ nish, apply one (1) THIN coat of stain.

• For a darker or more opaque ﬁ nish, apply two (2) or more

coats. Some colors may require up to four (4) coats to obtain

a completely opaque look. Be sure to wait at least 30 minutes

between coats.

• For a high-contrast look, paint just the brick surfaces.

For a monochromatic look, paint brick surfaces and grout lines.

• Do not mix stain with wet mortar.

Figure 2

MATERIAL SAFETY DATA SHEETS

To obtain a Material Safety Data Sheet:

1. Go to http://www.alsey.com.

2. Click the Fireplace Products tab.

3. In the lower left corner of the window, click the MSDS & Product Data Sheets button.

4. In the lower portion of the window, click the link for the applicable stain color next to Alsey Firebrick Stain and Color Enhancer.

CAUTION

• Stain may contain PM ACETATE and/or TITANIUM DIOXIDE. May

cause skin or respiratory irritation. Avoid prolonged exposure.

Avoid contact with eyes. Wash thoroughly after handling.

• Close container after each use. In case of spillage, absorb with

inert material, and dispose of in accordance with applicable

regulations.

Astria Fireplaces Mission Instruction Sheet

Astria Fireplaces Mission Instruction Sheet

Astria Fireplaces Mission Instruction Sheet

Related papers

Other documents