Package Contents
Pleasegoto forproductcleaningtips.Gotothe selection.
Integrated35WLED
www.quoizel.com Care+Maintenance
LightSource:
ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
EstimatedAssemblyTime:
Preparation:
45-60minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
1of2
Assembly Instruction Sheet #IS-CMA1405
For Styles CMA1405WT and CMA1405BN
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
CAUTION: To reduce the risk of fire, electrical shock, or personal injury, do not touch or remove the spot light on the rail when the light
is on. Instead, turn off the electrical power. Unscrew the caps and to remove the spot light from the rail. Then reinstall them back onto
the desired positions of the rail.
F
Wall
Anchor
x5
G
Self-tapping
Screw
x5
STEP 2 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Twist
connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires into the Outlet Box.
White wire
from supply
White wire
from fixture
Black wire from
supply (or Red)
Black wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 2
2016 QuoizelInc.
B
Ceiling
Canopy
x1
E
Spot Light
x5
C
Rail Support
x5
D
Rail
x1
STEP 1 Attach Crossbar to
Outlet Box
-
A. Attach the Crossbar (A) to Outlet
Box and secure by threading
Outlet Box Screws (not supplied)
into the Mounting Holes on the
Outlet Box. Tighten until snug.
A
Figure 1
Outlet
Box
Outlet Box
Screw
STEP 3 - Attach Ceiling
Canopy to Crossbar
A. Line up the holes on the
side of the Ceiling
Canopy (B) to the
mounting holes on the
Crossbar (A). Secure
them with Mounting
Screws (H). Tighten
until sung.
H
Mounting
Screw
x2
A
Crossbar
x1
H
A
B
Figure 3
STEP 4 Determine Support Position-
A. Mark two desired positions and drill them on the ceiling for two Rail
Supports (C) on the side of the Ceiling Canopy (B).
NOTE: Center the Ceiling Canopy (B) between two Rail
Supports (C) and The distance between each Rail Support (C)
and the canopy is 14 ~ 18 inches (See Fig 2-a). So the remainder
length of the rail could be bent to a wonderful arc.
Figure 4
14~15 inches
Rail
Support
Rail
Support
14~15 inches
CEILING
STEP 5 Rail support
Installation
-
A. Depart the Rail Supports
(C) as shown.
B. Insert Wall Anchors (F) into
the holes on the Ceiling.
Pass Support Base over
Self-tapping Screws (G)
and thread Self-tapping
Screws (G) into Wall
Anchors (F). Hand tighten
until snug.
C. Threading the Pipe of Rail
Supports into the Support
Bases , Tighten until snug.
Pipe of
Rail Support
Support
Base
Cap
C
CEILING
F
Support
Base
Pipe of
Rail Support
Figure 5
Figure 6
ReleaseDate:2016-03-30
2of2
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2016 QuoizelInc.
ReleaseDate:2016-03-30
STEP 7 continued
Repeat the steps of Rail Supports Installations to locate the rest Rail
Supports. Then Follow steps STEP 6 of Rail Installation to install the
Rail onto the other rail supports.
CMA1405WT/ CMA1405BN
FINISH: WESTERN BRONZE
BRUSHED NICKEL
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/4"
PART NUMBER
G12764SH
G12768DE
REPLACEMENT PART
HEAD
RAIL SUPPORT
NO.
1
2
QTY.
5
5
STEP 6 Instal Rail to Rail Support
NOTE: The Shallow V-pit on the Rail is always facing to the
ceiling.
-
A. Carefully take out the Rail (D) from the package and unfold it. There
has an Indented Groove and Brass Strip in the side of the Rail (D).
B. Turn the Moveable Part of the Rail Support body up. Attach the Rail
(D), while making certain the indented groove are facing toward the
bump, securely into the Rail Support.
D. Close back the moveable part of Rail Support (C) over the rail, then
restore the Caps back to the Rail Support (C).
Brass Strip
Rail
Indented
Groove
Cap
Brass Strip
Rail
Support
Moveable part
of Rail Support
Figure 7
Figure 8
STEP 7 Instal Rail to Ceiling Canopy
Note: If the Adapter is not able to close around the Rail, turn Rail
around so Adapter fits properly.
CAUTION: To ensure the fixture works correctly, make sure the
connection between the Adapter and the Rail is correct.
-
A. Unscrew the Caps from the Rail Adapter, and then turn the Moveable
Part of the Rail Adapter body up.
B. Attach the Rail (D) onto the slot of the pre-tightened Rail Adapter.
C. Close back the Moveable Part of Rail Adaptor body over the Rail (D),
then restore the caps back to the rail adapter. Make certain that the
Brass Clips of the adapter are connected properly with the Brass
Strips of the Rail (D).
D. Shape the Rail (D) as your desired. Then mark and drill the desired
positions on the ceiling for the rest of the Rail Supports (C).
Cap
Brass Strip
Bump
Rail Adapter
Moveable Part
of Rail Adapter
B
D
Bump
Brass Clip
C
STEP 8 Spot Light Installation
CAUTION: To ensure the fixture works correctly, make sure the
connection between the adapter and the rail is correct. The
Shallow V-pit on the Rail is always facing to the ceiling.
Note: Adjust the spotlight head to a desired position by using
the swivel.
-
A. Choose one spot light, unscrews the Caps from the Rail Adapter of
Spot Light (E), then turn the Moveable Part of Rail Adapter body
down.
B. Attach the Rail Adapter of the Spot Light (E) onto the Rail (D). Close
back the Moveable Part of Rail Adaptor body over the Rail (D), then
restore the Caps back to the Rail Adapter. Make certain that the
Brass Clips of the Adapter are connected properly with the Brass
Strips of the Rail.
C. Follow steps A~B to install the other spot lights onto the rail.
Your fixture is now assembled and ready to use. Enjoy!
Rail
Cap
Rail
Adapter
Moveable Part
of Rail Adapter
Spot Light
Head
E
D
Indented
Groove
Shallow V-Pit
Rail Adapter
Rail
Brass
Strip
Rail
Brass Strip
Shallow V-Pit
Indented Groove
Rail Adapter
Brass Clip
Brass Clip
Figure 10
Figure 9
Figure 11
Figure 12
3.75”
3”
9.25”
1.75”
11.75”
108”
4.75”Dia.
ITEM NUMBER
1
2
CMA1405BN
G12763SH
G12767DE
HEAD
RAIL SUPPORT
1
2
5
5
CMA1405WT
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Quoizel CTG1405BN Installation guide
-
Quoizel CFT9364BN Installation guide
-
Quoizel VVKY6328BN Installation guide
-
Quoizel COR1611K Installation guide
-
Quoizel VVAM6130PN Installation guide
-
Quoizel Q2605FOI Installation guide
-
Quoizel UST6127WT Installation guide
-
Quoizel PCOH3120OI Cohen 19.75 3 Blade Indoor LED Ceiling Fan Installation guide
-
Quoizel KY6328IB Installation guide
-
Quoizel VRG1612OI Operating instructions
