Eurotech Advme8028 Owner's manual

Brand: Eurotech

Model: Advme8028

Type: Owner's manual

Manual

VME Bus Intel Atom Processor CPU Board

Preface

Thank for choosing the Advme8028. Please read this manual before using the Advme8028so that you may obtain the

greatest benefit from using the device.

This manual presents the specifications, functions, and method of use of the VME Bus Intel Atom Processor CPU

Board Advme8028.

Advanet Inc. has made every effort to carefully inspect each product and has taken great care to package and to ship

the product. In the unlikely event of the product’s failure to operate normally due to problems in shipping or other-

wise, the company will repair or replace the product at its own responsibility.

Contact Advanet at the following address if you have any questions.

Inquiries

Sales Division

Headquarters

616-4 Tanaka, Kita-ku, Okayama 700-0951 Japan

TEL : 086-245-2861 FAX : 086-245-2860

Tokyo Office KDX Kaji-cho 4F , 3-5-2 Kanda Kaji-cho,

Chiyoda-ku, Tokyo 101-0045 Japan

TEL : 03-5294-1731 FAX : 03-5294-1734

INTERNETURL http://www.advanet.co.jp/

1. In order to improve the product, the contents of this document as well as product specifications are subject to change without notice.

2. This document does not give permission to the implementation of patents or other rights held by Advanet or third parties.

3. Reproduction of all or part of this document without Advanet’s permission is prohibited.

2009-2011 Advanet Inc.

Precautions in Use

Please read this manual before using the product in order to insure its safe use.

Do not place the product in a

location where it can fall or be

subject to vibration or impact

because this may cause device

failure.

Protect the device from vibration and impact.

Do not modify the device.

For safety reasons, under no

circumstances should you

modify the device. Advanet will

not repair products that have

been modified.

Protect the product from water

and chemicals.

Contact between the product

and water or chemicals can

result in product failure,

electrocution, or fire.

Protect the product from

foreign material.

Make sure that foreign

material does not get into the

product during use, storage, or

transport because this can

result in product failure.

Take precautions in handling to insure

that you are not injured.

The sharp projections on this

product may cause injury. Take

care in handling this product in

order to avoid injury.

Do not disassemble the product.

In order to maintain

guaranteed product

performance, do not under any

circumstances disassemble

this product.

Keep the product away from radios and TVs.

Do not use the product near

radios, television sets, or other

devices generating strong

magnetic or electrical fields.

This could result in failure or

malfunction.

Keep the product away from

flame, humidity, and direct sunlight.

Do not use or store the product

in any of the following locations

as this could result in product

failure.

Places where there is fire.

Locations high in humidity

or exposed to rain

Locations exposed to direct

sunlight

Dusty or dirty locations

Locations containing

excessive water or

chemical vapors

Precautions in use

Please read this manual before using the product in order to insure its safe use.

Install the product in well-ventilated locations.

Install the product in well-

ventilated locations to

efficiently disperse heat

generated by the product.

Remove the power plug from the receptacle

when not using the product.

Turn off the main switch and

remove the power plug from

the receptacle when not using

the product, or there is the risk

of lightning strike.

Be sure to use the device within rated parameters.

Be sure to use the product

within the ratings specified in

this manual. Failure to do so

may result in malfunction.

Cleaning the product

If the product becomes dirty,

wipe it with a dry soft cloth. A

thinned neutral cleaner may be

used if the product is

particularly dirty. Do not use

benzene, thinners, or other

solvents under any

circumstances.

Be sure to ground the product in order

to prevent electrocution.

Be sure to ground the product

by connecting it to a 3-pole AC

receptacle or by using an AC

receptacle having a grounding

terminal.

Be sure to dispose of the product properly.

Use appropriate methods for

handling industrial wastes

when disposing of this product.

Please contact Advanet for repair of the product.

Please contact your retail

dealer or Advanet when repairs

are necessary.

Make sure that the product is not miswired.

Failure to wire the product

correctly can result in

malfunction or fire. Read this

manual and wire the product

correctly.

Static electricity may cause malfunction.

This product comprises

electronic parts that are highly

susceptible to static electricity.

Static electricity can cause the

product to malfunction. Take

care not to touch any of the

terminals, connectors, ICs, or

other parts with the hands.

When you believe the product to be malfunctioning

Stop using the product if you

believe it is malfunctioning.

Continuing to use a

malfunctioning product can

cause the malfunction to

spread to other products and

can cause short circuits or fire.

Content

1. Prior to Use .............................................................................................................................................................................. 9

1.1 Period and Scope of Warranty .......................................................................................................................................... 9

1.2 Scope of Service ............................................................................................................................................................... 9

2. Outline ..................................................................................................................................................................................... 10

3. Specifications .......................................................................................................................................................................... 11

3.1 CPU ................................................................................................................................................................................... 11

3.2 Chip Set ............................................................................................................................................................................11

3.3 Memory ............................................................................................................................................................................. 11

3.4 Bus Bridge ........................................................................................................................................................................12

3.5 On-board I/O .....................................................................................................................................................................12

3.6 Front I/O ............................................................................................................................................................................12

3.7 VME Bus .......................................................................................................................................................................... 13

3.8 Operating Switches, Displays, Connectors ......................................................................................................................13

3.9 RAS Functions ..................................................................................................................................................................13

3.10 Power Supply ..................................................................................................................................................................14

3.11 Environmental Specification ..........................................................................................................................................14

3.12 Dimensions .....................................................................................................................................................................15

4. Panel Exterior View ................................................................................................................................................................16

4.1 RUN LED .........................................................................................................................................................................17

4.2 PMC Slot 1,2 ....................................................................................................................................................................17

4.3 RS232C Serial Port ........................................................................................................................................................... 17

4.4 Ethernet ............................................................................................................................................................................. 17

4.5 Reset Switch ..................................................................................................................................................................... 17

4.6 USB Port ........................................................................................................................................................................... 17

4.7 VGA .................................................................................................................................................................................. 17

5. Block Diagram ........................................................................................................................................................................ 18

6. Settings ....................................................................................................................................................................................19

6.1 CompactFlash Socket (CN6) ............................................................................................................................................ 20

6.2 PMC Connector (J1 to 2,5 to 6) .......................................................................................................................................20

6.3 Board Setup Switch (DSW1) ............................................................................................................................................21

6.3.1 VME System Controller Setting (Bit1) .................................................................................................................... 21

6.3.2 VME SYSRESET Output Setting (Bit2) ................................................................................................................. 21

6.3.3 VME SYSRESET Input Setting (bit3) ..................................................................................................................... 21

6.4 Lithium Battery Holder (BT1) ..........................................................................................................................................21

7. Address Maps ..........................................................................................................................................................................22

7.1 Memory Address Map ...................................................................................................................................................... 22

7.2 I/O Address Map ...............................................................................................................................................................22

7.3 Special Registers Address Map ........................................................................................................................................23

7.3.1 Watchdog Trigger Register (0280h) ......................................................................................................................... 23

7.3.2 Watchdog Control Register (0281h) ........................................................................................................................ 23

7.3.3 Power Management Control Register (0282h) ........................................................................................................ 23

7.3.4 Power Management Status Register.1 (0283h) ........................................................................................................24

7.3.5 Power Management Status Register.2 (0284h) ........................................................................................................24

7.3.6 Thermal Management Control Register (0285h) ..................................................................................................... 24

7.3.7 Board Status Register (0286h) .................................................................................................................................25

7.4 SMBus Address Map ........................................................................................................................................................ 25

8. Addition Matter .......................................................................................................................................................................26

8.1 VGA .................................................................................................................................................................................. 26

8.2 Ethernet ............................................................................................................................................................................. 26

8.3 PCI Device ........................................................................................................................................................................ 26

8.4 VME Interface .................................................................................................................................................................. 26

8.5 Real Time Clock ...............................................................................................................................................................26

8.6 EEPROM for Boot Data Storage ......................................................................................................................................26

8.7 Board Temperature Monitor .............................................................................................................................................26

9. Connector ................................................................................................................................................................................ 27

9.1 Serial Port (COM1,2) ...................................................................................................................................................... 27

9.2 Ethernet Connector (ETHERNET) ...................................................................................................................................27

9.3 USB Connector (USB) .....................................................................................................................................................27

9.4 VGA Port ........................................................................................................................................................................... 28

9.5 PMC J1(J5) Connector ..................................................................................................................................................... 29

9.6 PMC J2(J6) Connector ..................................................................................................................................................... 30

9.7 VME P1 Connector ...........................................................................................................................................................31

9.8 VME P2 Connector ...........................................................................................................................................................32

10.BIOS Setup ............................................................................................................................................................................. 33

10.1 Main Menu ..................................................................................................................................................................... 33

10.2 Advanced Menu ..............................................................................................................................................................33

10.3 Security Menu ................................................................................................................................................................. 35

10.4 Power Menu .................................................................................................................................................................... 35

10.5 Boot Menu ......................................................................................................................................................................36

10.6 Exit Menu .......................................................................................................................................................................36

Appendix A. PCI-VME bus bridge NARUTO Software Interface Manual

A-1 Outline ................................................................................................................................................................................. 37

A-2 Specifications ......................................................................................................................................................................38

A-2-1 PCI bus Interface ......................................................................................................................................................... 38

A-2-2 VME bus Interface ...................................................................................................................................................... 38

A-2-3 DMA Controller ........................................................................................................................................................... 39

A-2-4 Others .......................................................................................................................................................................... 39

A-3 Registers .............................................................................................................................................................................. 40

A-3-1 PCI Configuration Registers ....................................................................................................................................... 40

A-3-1-1 Vendor ID ............................................................................................................................................................. 40

A-3-1-2 Device ID ............................................................................................................................................................. 40

A-3-1-3 Command ............................................................................................................................................................. 40

A-3-1-4 Status .................................................................................................................................................................... 41

A-3-1-5 Revision ID .......................................................................................................................................................... 41

A-3-1-6 Class ID ................................................................................................................................................................41

A-3-1-7 Base Address Register 0 (BAR0) ........................................................................................................................41

A-3-1-8 Base Address Register 1 (BAR1) ........................................................................................................................41

A-3-1-9 Base Address Register 2 (BAR2) ........................................................................................................................41

A-3-1-10 Base Address Register 3 (BAR3) ...................................................................................................................... 41

A-3-1-11 Subsystem Vendor ID ........................................................................................................................................42

A-3-1-12 Subsystem ID .....................................................................................................................................................42

A-3-1-13 Interrupt Line ..................................................................................................................................................... 42

A-3-1-14 Interrupt Pin ....................................................................................................................................................... 42

A-3-2 PCI Special Register .................................................................................................................................................... 43

A-3-2-1 Board Status Register(Offset:00h) ....................................................................................................................... 44

A-3-2-2 A32 Control Register(Offset:04h) ....................................................................................................................... 44

A-3-2-3 A32 Forward Address Register(Offset:10h) ........................................................................................................44

A-3-2-4 A24 Control Register(Offset:24h) ....................................................................................................................... 45

A-3-2-5 A16 Control Register(Offset:2Ch) .......................................................................................................................45

A-3-2-6 Interrupt Status Register(Offset:34h) .................................................................................................................. 45

A-3-2-7 Interrupt Enable Register(Offset:38h) ................................................................................................................. 46

A-3-2-8 Interrupt Vector Register(Offset:3Ch) ................................................................................................................. 47

A-3-2-9 IRQ Generate Register(Offset:70h) ..................................................................................................................... 47

A-3-2-10 Interrupt Level Register(Offset:74h) ................................................................................................................. 48

A-3-2-11 IRQ1 Status ID Register(Offset:80h) .................................................................................................................48

A-3-2-12 IRQ2 Status ID Register(Offset:84h) ................................................................................................................48

A-3-2-13 IRQ3 Status ID Register(Offset:88h) ................................................................................................................48

A-3-2-14 IRQ4 Status ID Register(Offset:8Ch) ................................................................................................................ 48

A-3-2-15 IRQ5 Status ID Register(Offset:90h) ................................................................................................................49

A-3-2-16 IRQ6 Status ID Register(Offset:94h) ................................................................................................................49

A-3-2-17 IRQ7 Status ID Register(Offset:98h) ................................................................................................................49

A-3-2-18 A32 PCI Offset Register(Offset:40h) ................................................................................................................49

A-3-2-19 A32 VME Offset Register(Offset:44h) ..............................................................................................................49

A-3-2-20 A32 Area Register(Offset:48h) ..........................................................................................................................50

A-3-2-21 Post Interrupt0 Register(Offset:4Ch) .................................................................................................................51

A-3-2-22 Post Interrupt1 Register(Offset:50h) .................................................................................................................51

A-3-2-23 Post Interrupt2 Register(Offset:54h) .................................................................................................................51

A-3-2-24 Post Interrupt3 Register(Offset:58h) .................................................................................................................51

A-3-2-25 Semaphore Port 0 Register(Offset:5Ch) ............................................................................................................ 51

A-3-2-26 DMA Control/Status Register(Offset:60h) ........................................................................................................ 52

A-3-2-27 DMA PCI Offset Register(Offset:64h) ..............................................................................................................53

A-3-2-28 DMA VME Offset Register(Offset:68h) ........................................................................................................... 53

A-3-2-29 DMA Transfer Byte Count Register(Offset:6Ch) .............................................................................................. 53

A-3-3 VME Special Register ................................................................................................................................................. 54

A-3-3-1 Interrupt Level Register .......................................................................................................................................54

A-3-3-2 Interrupt Vector Register ...................................................................................................................................... 55

A-3-3-3 Post Interrupt0 Register ....................................................................................................................................... 55

A-3-3-4 Post Interrupt1 Register ....................................................................................................................................... 55

A-3-3-5 Post Interrupt2 Register ....................................................................................................................................... 55

A-3-3-6 Post Interrupt3 Register ....................................................................................................................................... 55

A-3-3-7 Semaphore Port1 Register ................................................................................................................................... 56

A-3-3-8 Semaphore Port2 Register ................................................................................................................................... 56

A-3-3-9 Semaphore Port3 Register ................................................................................................................................... 56

A-3-3-10 Semaphore Port4 Register .................................................................................................................................56

A-3-3-11 Semaphore Port5 Register .................................................................................................................................56

A-3-3-12 Semaphore Port6 Register .................................................................................................................................57

A-3-3-13 Semaphore Port7 Register .................................................................................................................................57

A-4 Example of Access to The VME bus ................................................................................................................................... 58

A-4-1 VME bus Master .......................................................................................................................................................... 58

A-4-1-1 Access to the A32 Space ......................................................................................................................................58

A-4-1-2 Access to theA24 Space ....................................................................................................................................... 59

A-4-1-3 Access to theA16 Space ....................................................................................................................................... 59

A-4-2 VME Bus Slave ...........................................................................................................................................................60

A-4-3 Byte Swap .................................................................................................................................................................... 61

1. Prior to Use

1.1 Period and Scope of Warranty

Delivered products are under warranty for a period of one year after delivery.

During the period of warranty, the vendor will have his own to responsibility replace or repair malfunctioning

parts if the product malfunction is the responsibility of the vendor.

However, this warranty does not apply under the following circumstances:

(1) If the user handles or uses the product in an inappropriate way

(2) If the malfunction is caused by something other than the delivered product

(3) If the delivered product has been modified or repaired by anyone other than the vendor

(4) Due to natural disaster, accident, or other reason not the responsibility of the vendor

In this context, the term “warranty” means solely a warranty of the individual delivered product, and does not

include any compensation for the damage caused by malfunction of the delivered product.

1.2 Scope of Service

The service costs such as the costs of sending technical personnel are not included in the price of the delivered

product. Customers will be charged for the following costs:

(1) Assistance with installation adjustments and test running

(2) Maintenance inspections, adjustments, and repairs

(3) Technical assistance and technical training

2. Outline

The Advme8028 is an Intel Atom processor (Z520P)-integrated 6U VME bus single board computer with the single slot

width.

Z520P operates on a frequency of 1.33GHz and incorporates 24kbytes of cache for data, 32kbytes of L1 cache for

command, and 512kbytes of L2 cache for data/command. The Advme8028 is equipped with DDR2-533 SDRAM

(1GB) for main memory. The Atom processor is System on Module (marketed as Catalyst) .

The Advme8028 is equipped with the Gigabit Ether channel (1 ch), USB port (1 ch), and VGA port for front panel

I/O interfaces. It also has a single CompactFlash socket and two PMC slots on board. The Advme8028 offers optional

slot system which allows the 2-ch serial port to be used from the front panel, instead of lessening the PMC slots to one.

The VME interface bus, which is an external bus, has an on-board Advanet PCI-VME bridge, the “NARUTO”.

This board has the following features:

 Intel Atom processor Z520P (1.33GHz) VME bus CPU board

 On-board DDR2-533 SDRAM (1GB) for main memory

 Equipped with system control hub US15W for the chip set

 Equipped with 1 channel Gigabit Ethernet (RJ-45 × 1)

 Can use CompactFlash as the storage device (provied with socket, module is optional)

 Equipped with a single 32bit/33MHz PMC 2slots, facilitating easy expansion of various functions

 No RS232C serial port enabled if two PMC slots are installed

 2-ch RS232C serial port enabled if a single PMC slot is installed (Dsub9p × 2)

 Boot ROM (On-board , FWH-FLASH Memory)

 The BIOS setup information and Real Time Clock are backed up with a litium battery

 Provided with 2kbit serial EEPROM (nonvolatile memory)

 Interface with the VME bus by the Advanet PCI-VME bridge, “NARUTO”

 Can operate as a VME bus master or slave

 6U (double height), single slot width VME bus port

 Operates with a single 5V power supply from the VME bus

 RoHS compliant

3. Specifications

3.1 CPU

3.2 Chip Set

3.3 Memory

Item Specification

Processor Intel Atom Processor Z520P

Core operating frequency 1.33GHz

L1 cache 24kB for data / 32kB for instruction

L2 cache Data /also for Instruction 512kB

FSB frequency 533 MHz

Intel Technology

Hyper-Threading Technology correspondence

Virtualization Technology correspondence

Extension Intel SpeedStep Technology correspondence

Thermal design power 2.2W

Heat sink None

Item Specification

System Control Hub Intel SCH US15W

Item Specification

Main Memory On board implementation

Memory bus operating frequency 533 MHz(DDR2-533)

Memory capacity 1GB

Boot ROM FWH-FLASH memory

On board implementation

On-board erase/write enabled.

Storing BIOS setup information

Serial EEPROM 2kbit(24C02 or compatible product)

Non-volatile memory to store boot information

3.4 Bus Bridge

3.5 On-board I/O

3.6 Front I/O

Item Specification

PCI-VME Bridge Advanet NARUTO

Bridges which interfaces internal PCI bus and VME bus.

VME bus Spceification Revision C.3

VME bus Master / Bus Slave

Includes DMA contoroller

Item Specification

Ethernet 10/100/1000Base-T, RJ-45 connector, 1port

Intel 82574L 1

USB USB 2.0, Type-A connector, 1port

SCH US15W built in USB controller is used.

Serial Port

(Option)

TIA/EIA-232E standard, start-stop synchronization ,

Dsub(9p) connector, 2port

Internal USB-capable FT232R

Single PMC slot enabled if the serial port is installed

Item Specification

CompactFlash CF+ and CompactFlash Rev2.1 standards

Connected as a primary IDE master device

No front loading, HotSwap is not available

CompactFlash retaining spacer attached

(No CompactFlash installed)

PMC IEEE 1386.1 standards

PCI Local Bus Rev2.2 standards

PCI32bit/33MHz, Signaling level 3.3V

Interrupt Signals Supports INTA#,INTB#,INTC#,INTD#

Power Supply +5.0V,+3.3V,+12V, 12V

(Power other than 3.3V directly supplied from the VME bus)

Single size(74mm 149mm)

2Slots (Single slot enabled if the optional COM port is installed)

3.7 VME Bus

3.8 Operating Switches, Displays, Connectors

3.9 RAS Functions

Item Specification

On-Board CompactFlash Socket

PMC Slot

CR2032 Battery Holder

2 ( 1)

Front Panel RUN-LED (Yellow / Green / Red)

Reset Switch

RS232C Connector

PMC Blank Panel

USB Connector

Ethernet Connector

0 ( 2)

2 ( 1)

(LINK-LED(Green), Activity-LED(Yellow)internal)

Item Specification

Bus Standard VME bus Specification Revision C.3

Controller NARUTO by Advanet

Connector P1,P2 (3lines,96pin Connector)

Board Type VME bus master / slave

System controller / non-system controller can be select by switch.

VME master / slave A32,A24,A16

D32,D16,D08 (EO)

Interrupt IRQ[7..1]* Interrupt output enable,

RQ[7..1]* Interrupt input enable

System Controller SYSRESET Driver, SYSCLK Driver

Item Specification

Watchdog Timer Timeout period selectable between 125 msec and 16 sec

The following may occur upon time-out:

NMI (PCI bus SERR# interrupt)

Reset

Temperature Monitor Monitors the temperature as follows

PCB surface temperature

3.10 Power Supply

3.11 Environmental Specification

Item Specification

Operating Temperature Range

40 to 85

Operating Humidity Range 35% to 80%RH (non-condensing)

Storage Temperature Range

40 to 85

Storage Humidity Range 5% to Under 95%RH (non-condensing)

Item Specification

Power Supply Voltage DC5.0V 5%

Current Consumption 1.6A typ(Design predicted valu . PMC module not included)

Battery The BIOS setup information and clock are backed up

Model number:CR2032

Storage for approximately 4.13years with power off, at 25

Storage for approximately 4.33years with power on,at 25

(Only data loss occurs upon power-off if it is not battery-

powered backed up.)

3.12 Dimensions

External form 6U, single slot width

Board dimensions 160mm × 233.35mm

Board thickness 1.6mm

Weight About 300g

External dimensions See drawing, below

[Figure 3.12] External Dimensions

261.75

20.02 17

170

160

233.35

4. Panel Exterior View

[Figure 4] External view of panel

PMC slot.1

PMC slot.2

Ethernet

Link LED

Activity LED

Reset switch

USB

VGA

(2-ch RS232C serial port enabled 

if a single PMC slot is installed)

RUN LED

4.1 RUN LED

This LED shows the CPU operating status. The meaning of the LED is as follows.

[Table4.1] RUN LED

4.2 PMC Slot 1,2

This slot is for installation of the PMC module.The blank panel is attached to keep the board inside, with no PMC

module installed.When installing the PMC module, remove the PMC blank panel.See section 6.2 for specifica-

tions for available PMC modules and sections 9.5 and 9.6 for connector pin assignment.

4.3 RS232C Serial Port

This is a connector for the RS232C serial port available when a single PMC slot is installed.Turn power off before

attaching or detaching cable to this connector.

See Section 9.1 for pin assignments.

4.4 Ethernet

Ethernet port is compatible with 10/100/1000 Base-T Ethernet.

The link LED turns on in green when the link is established, and the activity LED turns on in Yellow when transmis-

sion and reception take place.

See Section 9.2 for pin assignments.

4.5 Reset Switch

This is the switch for overall resetting of the this board and the VME bus.

When the reset switch is pushed, both this board and VME buses are reset.

VME bus setting (reset/ no reset) is selectable according to DIP switch setting.

Refer to Section 6.3 for details.

4.6 USB Port

This is the USB port connector. This port is controlled by ICH-integrated USB.

See Section 9.3 for pin assignments.

4.7 VGA

This is the VGA connector.Turn power off before attaching or detaching cable to this connector.

See Section 9.4 for pin assignments.

Status RUN LED

Indicates that power is off. Off

CPU is being activated. Yellow

Indicates that the CPU is running. Green

This indicates that the RED_LED bit is set to "1" by

software when the CPU is running.

Red

5. Block Diagram

[Figure 5] Block Diagram

PMC Slot

Temp.

Sensor

EEPROM

2kbit

Socket

Battery

PCIe to PCI

Bridge

PCI-VME Bridge

FPGA

Catalyst Module

Atom CPU

Chip Set

Gigabit

Ethernet

RJ-45

PCIe 1

PCIe

SDVO to VGA

Dsub

15pin

SDVO

Type-A

USB

USB to UART

Dsub

9pin

USB

USB to UART

Dsub

9pin

USB

VGA

ETHERNET

USB

COM

SMBus

ATA

PMC Slot

VME bus

PCI bus

(32bit/33MHz)

6. Settings

 CN6 .................................... CompactFlash sockt

 J1 to 2,5 to 6 ...................... PMC connector

 DSW1 ................................. Board setup switch

 BT1 .................................... Lithium battery holder

[Figure 6] Setting locations on the board

DSW1

CN6

J5 J6

J1 J2

BT1

6.1 CompactFlash Socket (CN6)

This is the socket for installing CompactFlash, which has a large nonvolatile memory capacity.

Available modules must be compatible with CompactFlash Type I that complies with CF+ and CompactFlash

Revision 2.1 and be capable of operation at 3.3V.

CompactFlashInstall with the power turned off.

The following are recommended CompactFlashes.

Maker : Transcend

Model : TS128MCF100I (128M-byte capacity)

TS256MCF100I (256M-byte capacity)

TS512MCF100I (512M-byte capacity)

TS1GCF100I (1G-byte capacity)

TS2GCF100I (2G-byte capacity)

TS4GCF100I (4G-byte capacity)

TS8GCF100I (8G-byte capacity)

TS16GCF100I (16G-byte capacity)

CompactFlash is designed to be connected as a primary IDE master device. CompactFlash interface used in this

board is not hot-swappable. The CompactFlash card must be inserted and removed with power off.

6.2 PMC Connector (J1 to 2,5 to 6)

This connector is for installation of the PMC expansion module.

The Advme8028 is compatible with only a PMC module that complies with specifications provided in table 6.2.

When installing the PMC module, remove the PMC blank panel.

See Section 9.5 to 9.6 for pin assignments.

[Table 6.2] PMC module specification

(*1) For supplying 12V or -12V power to the PMC module, this board needs the same power supply via

the VME P1 connector.

Item Specification

Supply Voltage DC5V 5%

DC3.3V 5%

DC12V 5% (

DC 12V 5% (

Consumption Current DC5V 1.5A and under

DC3.3V 4A and under

DC12V 0.5A and under

DC 12V 0.5A and under

Signaling Voltage 3.3V

Interface PCI (33MHz)

Board Size Single size (74mm 149mm)

PMC Connector P1, P2

Stack Height(Board interval) 10mm

Page is loading ...

Eurotech Advme8028 Owner's manual

Eurotech Advme8028 Owner's manual

Eurotech Advme8028 Owner's manual

Related papers

Other documents