Vents VENTS GK 125 MA Installation guide

www.vents-us.com

User’s

manual

Manuel

d'utilisation

Manual

de usuario

ES

EN

FR

Wall-Through Ventilation Fan

2

READ CAREFULLY AND SAVE THESE INSTRUCTIONS.

EN

WARNING!

READ CAREFULLY AND SAVE THESE INSTRUCTIONS TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK AND

PERSONAL INJURY.

1. Use the product only in the manner intended by the manufacturer. If you have questions, contact the manufacturer.

2. Before servicing or cleaning the product, switch off the power at the main service panel and lock it to prevent the

power from accidentally being turned on. If the panel cannot be locked securely, fasten a prominent warning device,

such as tag, to it. If the fan is not hard-wired but rather plugged into a 120 Volt outlet, unplug the cord from the

receptacle.

3. Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes

and standards, including fire-rated construction codes and standards.

4. Sufficient air is needed for proper combustion and exhaust of gases through the flue (chimney) of fuel burning

equipment to prevent back drafting. Follow the heating equipment manufacturer's guidelines and safety standards such

as those published by the National Fire Protection Association (NFPA), and the American Society for Heating,

Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities.

5. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

6. The exhaust fans must always be vented to outdoors.

7. The fan may have sharp edges. Use caution to avoid being cut when installing and cleaning.

8. The fan must be grounded.

CAUTION!

1. For general ventilation use only. Not for use in fire rated installations. Do not use the fan to exhaust hazardous or

explosive materials and vapors.

2. For interior use only. Mount with the lowest moving parts at least 8 feet (2.5 meters) above the floor or grade level.

3. To avoid the motor damage and noisy and/or unbalanced impeller, keep drywall spray, construction dust, etc. off the

power unit.

4. Prior to installation operations make sure there is no visible damage to the impeller and housing.

Also make sure there are no foreign objects in the fan.

5. Please read specification label on product for further information and requirements.

6. Both the inlet and outlet must have no obstructions for the fan to work properly and be covered by the warranty.

7. When storing the fan keep it in a dry, weather-protected environment in the original packaging. If the fan has been

stored or set in a cold environment, wait 2 hours before connecting it to the power source.

GENERAL

The product described herein is a ventilation for small up to medium-sized domestic premises. The fan and the ventilation fan

grille are made of plastic. The ventilation is designed for through-the-wall mounting, Fig. 1. fan

DELIVERY SET

Box includes:

1. Fan - 1

2. External grille - 1

3. Plastic air duct - 1

4. Screws and anchors - 6

5. User's manual

UNDERSTANDING MODEL NUMBER

The three digit number in all model names indicates the following:

100 (100 mm) means it is used with 4” air duct

125 (125 mm) means it is used with 5” air duct

150 (150 mm) means it is used with 6” air duct

MOUNTING

The ventilation is designed for through-the-wall mounting. fan

Mounting steps:

1. Select an installation place for the ventilation kit and drill a round core hole. Its diameter must match the air duct

diameter, Fig. 2.

2. Insert the air duct in the hole and fix it with a mounting foam, Fig. 3.

3. Install the fan, Fig. . 4-15

4. Install the external grille, Fig. . 16-19

Input: 120 VAC 60 Hz. The fan is equipped with a power cable with a plug for connection to a standard wall socket or with a

terminal box for direct connection to power supply. Connection to power supply is shown in Fig. . 20-23

OPERATION CONDITIONS

The ventilation kit is rated for continuous operation .

IPX4 rating ensures protection from splash of water for at least 5 minutes.

The fans can be operated at ambient temperatures between +32 F (0 °C) up to 113 F (+45 °C). +

MAINTENANCE

The fan surfaces need to be cleaned of dirt and dust regularly by using a soft, wet cloth and mild detergent.

Do not allow liquids to come in contact with the electric motor!

Wipe the surfaces dry after cleaning.

The product design is constantly being improved, that is why some models can differ slightly from those described in this

manual models.

3

WARRANTY

The product meets standard operating requirements in the North America.

VENTS US warrants to the original purchaser of the product that it will be free from defects in materials or workmanship for a

period of 24 months from the date of original purchase.

THERE ARE NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED

WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

During the stated warranty period, VENTS US will, at its option, repair or replace, without charge, any product or part which is

found to be defective under normal use and service. This warranty does not cover (a) normal maintenance and normal service

or (b) any products or parts which have been subject to misuse, negligence, accident, improper maintenance or repair

(other than by VENTS US), faulty installation or installation contrary to recommended installation instructions.

Labor to remove and replace products is not covered.

The duration of any implied warranty is limited to the time period specified for the express warranty.

Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.

VENTS US OBLIGATION TO REPAIR OR REPLACE, AT VENTS US OPTION, SHALL BE THE PURCHASER'S SOLE AND

EXCLUSIVE REMEDY UNDER THIS WARRANTY.

VENTS US SHALL NOT BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF OR IN

CONNECTION WITH PRODUCT USE OR PERFORMANCE.

Some states do not allow the exclusion or limitations of incidental or consequential damages, so the above limitation or exclusion

may not apply to you.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

This warranty supersedes all prior warranties.

If proof of sales date is not available, the warranty period is calculated from the production date.

The product can be exchanged at the following address:

Bodor Vents, LLC DBA: VENTS-US

11013 Kenwood Road Cincinnati, Ohio 45242

Phone: (513)348-3853

e-mail: [email protected]

Please follow guidelines in this manual for product problem-free operation.

4

Page is loading ...

Typical installation

1

11

Outer

wall

Inner

wall

Air duct installation

2

min 3°

3

12

Outer wall

Inner wall

Install the air duct with the minimum slope 3°

downwards to ensure condensate drainage. Fill the

gap between the air duct and the wall with

mounting foam.

Prepare a round hole in the exterior wall of the

building. The hole size and the minimum

recommended distance to a mounting surface,

for example, a wall, ceiling or a window are

shown in the Figure.

min 20"

100 Kit - DIA (5")

125 Kit - DIA (6")

150 Kit - DIA (7")

Installation of MA series wall-through ventilation fan

7

4

8

5

13

9

6

Use the back part of the front

panel to mark the four screw

holes. Drill the holes.

Remove the front panel cover to

enable access to the fastening

holes.

Connect the front panel cover with

the back part and secure them with

a screw at the bottom.

Route all the required cables.

If the fan is equipped with a

power cable and a plug, make

sure an electric outlet is located

no more than 9 ft from the fan.

Insert the expansion anchors in

the holes.

Fix the back part of the front

panel to the wall using the

supplied screws. Wire the fan

according to the wiring diagram in

Fig. 20 or 22.

13

10

14

11

15

12

Installation of series wall-through ventilation fanLD

14

Use the back part of the front

panel to mark the 4 screw

holes.Drill the holes.

Remove the front panel cover to

enable access to the fastening

holes.

Connect the front panel cover with

the back part and secure them

with a screw at the bottom.

Route all the required cables.

If the fan is equipped with a

power cable and a plug, make

sure an electric outlet is located

no more than 9 ft from the fan.

Insert the expansion anchors in

the holes.

Fix the back part of the front

panel to the wall using the

supplied screws. Wire the fan

according to the wiring diagram in

Fig. 21 or 23.

Installation of outer hood

15

Disassemble the ventilation hood to ensure access to

the fastening holes. Disconnect and remove the front

part of the ventilation hood.

Insert the expansion anchors in the holes

Fix the back part of the ventilation hood to the wall

using the supplied screws. Secure the hood to the

back plate by pressing the two parts together.

Easy click installation

Use the back part of the hood to mark the four

screw holes. Drill the holes.

18

16

19

17

120VAC, 60Hz

POWER SOURCE

QF

AUTOMATIC

SWITCH

GREEN

GROUND

SCREW

HOUSE JUNCTION BOX

EARTH

GROUND

FAN

Electrical Connection of MA series wall-through ventilation fan

STANDARD

WALL SOCKET

20

16

FAN

Electrical Connection of LD series wall-through ventilation fan

21

17

120VAC, 60Hz

POWER SOURCE

QF

AUTOMATIC

SWITCH

GREEN

GROUND

SCREW

HOUSE JUNCTION BOX

STANDARD

WALL SOCKET

EARTH

GROUND

S

JUNCTION

BOX

120VAC, 60Hz

POWER SOURCE

STANDARD

WALL SWITCH

QF

AUTOMATIC

SWITCH

GREEN

GROUND

WIRE

TO FAN

TO S

TO QF

AND

GROUND SCREW

GREEN

GROUND

SCREW

HOUSE JUNCTION BOX

GROUND

FAN

L

N

X

N

L

N

L

~120V 60Hz

X

QF

S

Electrical connection MA series standard wall switch

1g

22

18

S

JUNCTION

BOX

120VAC, 60Hz

POWER SOURCE

STANDARD

WALL SWITCH

QF

AUTOMATIC

SWITCH

GREEN

GROUND

WIRE

TO FAN

TO S

TO QF

AND

GROUND SCREW

GREEN

GROUND

SCREW

HOUSE JUNCTION BOX

GROUND

FAN

L

N

X

N

L

N

L

~120V 60Hz

X

QF

S

Electrical connection LD series standard wall switch

1g

23

19

www.vents-us.com

100

125

150

LD Kit

MA Kit

ACCEPTANCE CERTIFICATE

CERTIFICAT D'ACCEPTATION

CERTIFICADO DE CALIDAD

Date of sale

Date de la vente

Fecha de venta

Manufactured on (date):

Vendu

(nom d'entreprise de commerce, cachet du magasin)

Fabriqué le (date)

Approval mark

Fecha de producion

Signe d'approbation

Marca de verificador

Vendido

(nombre de empresa, timbro o sello)

Sold

(name of trading enterprise, stamp of store)

The fan has been duly certified as serviceable.

Le ventilateur a été certifié comme utilisable.

Este ventilador está certificado para el uso normal.

V-US141EN-02

Vents VENTS GK 125 MA Installation guide

This manual is also suitable for

Vents VENTS GK 125 MA Installation guide

in other languages

Related papers

Other documents