ABB IRB 6650S - 125/3.5 User manual

Product manual

Articulated robot

IRB 6650S - 200/3.0

IRB 6650S - 125/3.5

IRB 6650S - 90/3.9

M2000, M2000A, M2004

Product manual

IRB 6650S - 200/3.0

IRB 6650S - 125/3.5

IRB 6650S - 90/3.9

M2000

M2000A

M2004

Document ID: 3HAC020993-001

Revision: G

The information in this manual is subject to change without notice and should not be

construed as a commitment by ABB. ABB assumes no responsibility for any errors that

may appear in this manual.

Except as may be expressly stated anywhere in this manual, nothing herein shall be

construed as any kind of guarantee or warranty by ABB for losses, damages to persons

or property, fitness for a specific purpose or the like.

In no event shall ABB be liable for incidental or consequential damages arising from

use of this manual and products described herein.

This manual and parts thereof must not be reproduced or copied without ABB's written

permission, and contents thereof must not be imparted to a third party nor be used for

any unauthorized purpose. Contravention will be prosecuted.

Additional copies of this manual may be obtained from ABB at its then current charge.

ABB AB

Robotics Products

SE-721 68 Västerås

Sweden

Table of Contents

33HAC020993-001 Revision: G

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Product documentation, M2000/M2000A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Product documentation, M2004 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

How to read the product manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

1 Safety 17

1.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

1.2 General safety information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

1.2.1 Safety in the robot system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

1.2.2 Safety risks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

1.2.2.1 Safety risks during installation and service work on robot. . . . . . . . . . . . . . . . . . . . . . . . 19

1.2.2.2 Safety risks related to tools/workpieces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

1.2.2.3 Safety risks related to pneumatic/hydraulic systems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

1.2.2.4 Safety risks during operational disturbances. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

1.2.2.5 Risks associated with live electric parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

1.2.3 Safety actions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

1.2.3.1 Safety fence dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

1.2.3.2 Fire extinguishing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

1.2.3.3 Emergency release of the robot’s arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

1.2.3.4 Brake testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

1.2.3.5 Risk of disabling function "Reduced speed 250 mm/s" . . . . . . . . . . . . . . . . . . . . . . . . . . 30

1.2.3.6 Safe use of the FlexPendant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

1.2.3.7 Work inside the manipulator's working range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

1.2.3.8 Signal lamp (optional). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

1.2.3.9 Translate the information on safety and information labels . . . . . . . . . . . . . . . . . . . . . . . 34

1.3 Safety related instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

1.3.1 Safety signals, general . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

1.3.2 DANGER - Moving manipulators are potentially lethal! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

1.3.3 DANGER - First test run may cause injury or damage! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

1.3.4 WARNING - The brake release buttons may be jammed after service work . . . . . . . . . . . . . . . . 39

1.3.5 WARNING - The unit is sensitive to ESD! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

1.3.6 WARNING - Safety risks during work with gearbox oil. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

2 Installation and commissioning 43

2.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

2.2 Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

2.2.1 Pre-installation procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

2.2.2 Working range and type of motion. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

2.2.3 Risk of tipping / stability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

2.3 On-site installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

2.3.1 Lifting robot with fork lift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

2.3.2 Lifting robot with roundslings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

2.3.3 Lifting robot with lifting slings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

2.3.4 Manually releasing the brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

2.3.5 Lifting the base plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

2.3.6 Securing the base plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

2.3.7 Orienting and securing the robot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

2.3.8 Fitting equipment on robot. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

2.3.9 Installation of base spacers (option). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

2.3.10 Installation of cooling fan for motors, axes 1-3 (option) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

2.3.11 Loads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

2.4 Restricting the working range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

2.4.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

2.4.2 Mechanically restricting the working range of axis 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

Table of Contents

4 3HAC020993-001 Revision: G

2.4.3 Mechanically restricting the working range of axis 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88

2.4.4 Mechanically restricting the working range of axis 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

2.4.5 Installation of position switches (option). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92

2.5 Electrical connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101

2.5.1 Robot cabling and connection points. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101

2.6 Making robot ready for operation (Foundry Prime) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104

2.6.1 Additional installation procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104

2.6.2 Commissioning (Foundry Prime). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107

3 Maintenance 109

3.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109

3.2 Maintenance schedule and expected component life. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110

3.2.1 Specification of maintenance intervals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110

3.2.2 Maintenance schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111

3.2.3 Expected component life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116

3.3 Inspection activities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117

3.3.1 Inspection, oil level gearbox axis 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117

3.3.2 Inspection, oil level gearbox axis 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119

3.3.3 Inspection, oil level gearbox axis 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121

3.3.4 Inspection, oil level gearbox axis 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123

3.3.5 Inspection, oil level, gearbox axis 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125

3.3.6 Inspection, oil level gearbox axis 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127

3.3.7 Inspection, balancing device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130

3.3.8 Inspection, cable harness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135

3.3.9 Inspection, information labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139

3.3.10 Inspection, mechanical stop, axis 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141

3.3.11 Inspection, additional mechanical stops. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143

3.3.12 Inspection, damper axes 2-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146

3.3.13 Inspection, position switch axes 1, 2 and 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148

3.3.14 Inspection, signal lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150

3.3.15 Inspection of air hoses (Foundry Prime) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152

3.4 Replacement/changing activities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153

3.4.1 Type of oil in gearboxes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153

3.4.2 Oil change, gearbox axis 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157

3.4.3 Oil change, gearbox axis 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160

3.4.4 Oil change, gearbox, axis 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163

3.4.5 Oil change, gearbox, axis 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166

3.4.6 Oil change, gearbox, axis 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169

3.4.7 Oil change, gearbox axis 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172

3.4.8 Replacement of SMB battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175

3.5 Lubrication activities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178

3.5.1 Lubrication of spherical roller bearing, balancing device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178

3.5.2 Rust preventive, bearing axis 1 (Foundry Prime) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180

3.5.3 Rust preventive, bearing axis 4 (Foundry Prime) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182

3.5.4 Rust preventive, support bearing in wrist (Foundry Prime). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185

3.6 Cleaning activities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187

3.6.1 Cleaning, robot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187

3.7 Service Information System, M2000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189

3.7.1 Using the SIS system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189

3.7.2 Description of Service Information System (SIS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190

3.7.3 SIS system parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192

3.7.4 Setting the SIS parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194

3.7.5 Reading the SIS output logs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196

Table of Contents

53HAC020993-001 Revision: G

3.7.6 Exporting the SIS data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198

4 Repair 199

4.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199

4.2 General procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200

4.2.1 Performing a leak-down test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200

4.2.2 Mounting instructions for bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201

4.2.3 Mounting instructions for seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202

4.3 Complete robot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204

4.3.1 Replacement of cable harness, axes 1-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204

4.3.2 Replacement of cable harness, axes 1-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 216

4.3.3 Replacement of cable harness, axes 5-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225

4.3.4 Replacement of cabling, axis 5 motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 229

4.3.5 Replacement of complete arm system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 231

4.3.6 Replacement of air nipple and hose (Foundry Prime) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 236

4.4 Upper and lower arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 242

4.4.1 Replacement of turning disk. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 242

4.4.2 Replacement of complete wrist unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 245

4.4.3 Replacement of upper arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250

4.4.4 Replacement of complete lower arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 256

4.4.5 Replacement of lower arm shaft. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 263

4.4.6 Securing the lower arm. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 269

4.5 Frame and base. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 273

4.5.1 Replacement of SMB unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 273

4.5.2 Replacement of brake release unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 277

4.5.3 Replacement of spherical roller bearing, balancing device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 281

4.5.4 Replacement of balancing device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 286

4.5.5 Unloading the balancing device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 295

4.5.6 Restoring the balancing device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 298

4.6 Motors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300

4.6.1 Replacement of motor, axis 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300

4.6.2 Replacement of motor axis 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 306

4.6.3 Replacement of motor, axis 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 313

4.6.4 Replacement of motor, axis 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 320

4.6.5 Replacement of motor, axis 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 326

4.6.6 Replacement of motor, axis 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 333

4.7 Gearboxes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 339

4.7.1 Replacement of gearbox, axis 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 339

4.7.2 Replacement of gearbox axis 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 346

4.7.3 Replacement of gearbox, axis 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 354

4.7.4 Replacement of gearbox, axis 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 360

5 Calibration information 365

5.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 365

5.2 Calibration methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 366

5.3 Calibration scales and correct axis position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 368

5.4 Calibration movement directions for all axes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 369

5.5 Updating revolution counters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 370

5.6 Checking the calibration position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 373

5.7 Additional calibration instruction, IRB4400 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 375

6 Decommissioning 377

6.1 Environmental information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 377

Table of Contents

6 3HAC020993-001 Revision: G

6.2 Decommissioning of balancing device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 378

7 Reference information 381

7.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 381

7.2 Applicable Safety Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 382

7.3 Unit conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 383

7.4 Screw joints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 384

7.5 Weight specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 387

7.6 Standard toolkit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 388

7.7 Special tools. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 389

7.8 Lifting equipment and lifting instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 392

8 Spare part / part list 393

8.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 393

8.2 Spare part list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 394

8.2.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 394

8.2.2 Spare part list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 395

8.3 Part list. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 398

8.3.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 398

8.3.2 Rebuilding parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 399

8.3.3 Part list, overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 401

8.3.4 Base incl frame ax 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 402

8.3.5 Axis 3-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 403

8.3.6 Axis 3-4, Foundry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 407

8.3.7 Axis 3-4 Foundry Prime. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 408

8.3.8 Wrist, type 2, standard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 409

8.3.9 Wrist, type 2, Foundry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 413

8.3.10 Wrist, type 2, insulated. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 414

8.3.11 Wrist, type 2, Foundry Prime. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 415

8.3.12 Material set, manipulator, 3HAC 13263-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 416

8.3.13 Material set, axis 1-2, 3HAC 13264-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 417

8.3.14 Material set, balancing device, 3HAC 13265-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 420

8.3.15 Arm extension set, 450 mm, 3HAC 12311-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 421

9 Exploded views 423

9.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 423

9.2 Base incl. Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 424

9.3 Frame - lower arm 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 425

9.4 Frame - lower arm 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 426

9.5 Upper arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 427

9.6 Wrist complete . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 428

10 Circuit Diagram 429

10.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 429

10.2 Circuit diagram 3HAC 025744-001 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 430

10.2.1 Validity of circuit diagram 3HAC 025744-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 430

10.3 Circuit diagram 3HAC 13347-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 431

10.3.1 Validity of circuit diagram 3HAC 13347-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 431

Index 433

Table of Contents

73HAC020993-001 Revision: G

Table of Contents

8 3HAC020993-001 Revision: G

Overview

93HAC020993-001 Revision: G

Overview

About this manual

This manual contains instructions for

• mechanical and electrical installation of the robot

• maintenance of the robot

• mechanical and electrical repair of the robot.

Usage

This manual should be used during

• installation, from lifting the robot to its work site and securing it to the foundation to

making it ready for operation

• maintenance work

• repair work.

Who should read this manual?

This manual is intended for:

• installation personnel

• maintenance personnel

• repair personnel.

Prerequisites

A maintenance/repair/ installation craftsman working with an ABB Robot must:

• be trained by ABB and have the required knowledge of mechanical and electrical

installation/repair/maintenance work.

Organization of chapters

The manual is organized in the following chapters:

Chapter Contents

Safety Safety information that must be read through before performing

any installation or service work on robot. Contains general safety

aspects as well as more specific information about how to avoid

personal injuries and damage to the product.

Installation and commis-

sioning

Required information about lifting and installation of the robot.

Maintenance Step-by-step procedures that describe how to perform

maintenance of the robot. Based on a maintenance schedule

that may be used in the work of planning periodical maintenance.

Repair Step-by-step procedures that describe how to perform repair

activities of the robot. Based on available spare parts.

Calibration information Procedures that do not require specific calibration equipment.

Decommissioning Environmental information about the robot and its components.

Continues on next page

Overview

3HAC020993-001 Revision: G10

References

Additional document references

Revisions

Document name Document ID Note

Product specification - IRB 6600/6650/6650S M2004 3HAC023933-001

Product specification - IRB 6600/6650/6650S M2000/

M2000A

3HAC14064-1

Product manual - IRC5 3HAC021313-001

Product manual - S4Cplus M2000 3HAC021333-001

Product manual - S4Cplus M2000A 3HAC022419-001

Operating manual - IRC5 with FlexPendant 3HAC16590-1

User’s guide - S4Cplus 3HAC7793-1

Operating manual - Calibration Pendulum 3HAC16578-1

Operating manual - Levelmeter Calibration 3HAC022907-001 M2000/M2000A

Operating manual - Service Information System 3HAC025709-001 M2004

Technical reference manual - System parameters 3HAC17076-1

Application manual - Additional axes and stand alone

controller

3HAC021395-001 M2004

Application manual - External axes 3HAC9299-1 M2000/M2000A

Document name Document ID

CalibWare 2.0 User’s guide (M2000) 3HAC16090-1

Revision Description

- First edition.

A • Model M2004 implemented.

• Product manual divided into two parts: Product manual, procedures and

Product manual, reference information.

• New foldouts: Frame - lower arm 1 on page 425 and Frame - lower arm

2 on page 426.

• Updated list with special tools, section Special tools on page 389.

• Added spare part list, new section Spare part list on page 395.

Various corrections and editing made in text and figures due to technical

revisions etc.

B Chapter Calibration replaced with chapter Calibration information.

Section Document references is completed with article numbers for calibration

manuals.

C New lubricating oil in the gearboxes, axes 1, 2, 3 and 6. Changes made in:

• chapter Maintenance.

• section Part list.

Continued

Continues on next page

Overview

113HAC020993-001 Revision: G

D • Article number for mechanical stop set added to section Mechanically

restricting the working range of axis 2 on page 88.

• New section added to the manual: Installation of cooling fan for motors,

axes 1-3 (option) on page 78.

• A complete (undivided) cabling from axis 1 to axis 6 is added to the spare

parts in Spare part list on page 395. New procedure Replacement of

cable harness, axes 1-6 on page 204. Also a new circuit diagram is added

to the manual, due to the new cabling.

• IRB 6650S included in section Rebuilding parts on page 399.

E • New variant IRB 6650S - 90/3.9 is implemented throughout the manual.

F Foundry Prime Option included.

G Changes made in:

• Prerequisites in section Overview

• Oil change in section Maintenance

Revision Description

Continued

Product documentation, M2000/M2000A

3HAC020993-001 Revision: G12

Product documentation, M2000/M2000A

General

The complete product documentation kit for the M2000 robot system, including controller,

robot and any hardware option, consists of the manuals listed below:

Product manuals

All hardware, robots and controllers, will be delivered with a Product manual which is

divided into two parts:

Product manual, procedures

• Safety information

• Installation and commissioning (descriptions of mechanical installation, electrical

connections)

• Maintenance (descriptions of all required preventive maintenance procedures

including intervals)

• Repair (descriptions of all recommended repair procedures including spare parts)

• Additional procedures, if any (calibration, decommissioning)

Product manual, reference information

• Reference information (article numbers for documentation referred to in Product

manual, procedures, lists of tools, safety standards)

• Part list

• Foldouts or exploded views

• Circuit diagrams

The product manual published as a PDF consists of only one file where the two parts are

presented together, as one Product manual.

Software manuals

The software documentation consists of a wide range of manuals, ranging from manuals for

basic understanding of the operating system to manuals for entering parameters during

operation.

A complete listing of all available software manuals is available from ABB.

Controller hardware option manual

Each hardware option for the controller is supplied with its own documentation. Each

document set contains the types of information specified below:

• Installation information

• Repair information

• Maintenance information

In addition, spare part information is supplied for the entire option.

Product documentation, M2004

133HAC020993-001 Revision: G

Product documentation, M2004

General

The robot documentation may be divided into a number of categories. This listing is based on

the type of information contained within the documents, regardless of whether the products

are standard or optional. This means that any given delivery of robot products will not contain

all documents listed, only the ones pertaining to the equipment delivered.

However, all documents listed may be ordered from ABB. The documents listed are valid for

M2004 robot systems.

Product manuals

All hardware, robots and controllers, will be delivered with a Product manual which is

divided into two parts:

Product manual, procedures

• Safety information

• Installation and commissioning (descriptions of mechanical installation, electrical

connections)

• Maintenance (descriptions of all required preventive maintenance procedures

including intervals)

• Repair (descriptions of all recommended repair procedures including spare parts)

• Additional procedures, if any (calibration, decommissioning)

Product manual, reference information

• Reference information (article numbers for documentation referred to in Product

manual, procedures, lists of tools, safety standards)

• Part list

• Foldouts or exploded views

• Circuit diagrams

The product manual published as a PDF consists of only one file where the two parts are

presented together, as one Product manual.

Technical reference manuals

The following manuals describe the robot software in general and contain relevant reference

information:

• RAPID Overview: An overview of the RAPID programming language.

• RAPID Instructions, Functions and Data types: Description and syntax for all

RAPID instructions, functions and data types.

• System parameters: Description of system parameters and configuration workflows.

Continues on next page

Product documentation, M2004

3HAC020993-001 Revision: G14

Application manuals

Specific applications (e.g. software or hardware options) are described in Application

manuals. An application manual can describe one or several applications.

An application manual generally contains information about:

• The purpose of the application (what it does and when it is useful)

• What is included (e.g. cables, I/O boards, RAPID instructions, system parameters, CD

with PC software)

• How to use the application

• Examples of how to use the application

Operating manuals

This group of manuals is aimed at those having first hand operational contact with the robot,

i.e. production cell operators, programmers and trouble shooters. The group of manuals

includes:

• Getting started - IRC5 and RobotStudio

• IRC5 with FlexPendant

• RobotStudio

• Trouble shooting - IRC5 for the controller and robot

Continued

How to read the product manual

153HAC020993-001 Revision: G

How to read the product manual

Reading the procedures

The procedures contain references to figures, tools, material etc. The references are read as

described below.

References to figures

The procedures often include references to components or attachment points located on the

robot/controller. The components or attachment points are marked with italic text in the

procedures and completed with a reference to the figure where the current component or

attachment point is shown.

The denomination in the procedure for the component or attachment point corresponds to the

denomination in the referenced figure.

The table below shows an example of a reference to a figure from a step in a procedure.

References to required equipment

The procedures often include references to equipment (spare parts, tools etc.) required for the

different actions in the procedure. The equipment is marked with italic text in the procedures

and completed with a reference to the section where the equipment is listed with further

information, i.e. article number, dimension.

The denomination in the procedure for the component or attachment point corresponds to the

denomination in the referenced list.

The table below shows an example of a reference to a list of required equipment, from a step

in a procedure.

Safety information

The manual includes a separate safety chapter that must be read through before proceeding

with any service or installation procedures. All procedures also include specific safety

information when dangerous steps are to be performed.

Read more in chapter Safety on page 17.

Action Note/Illustration

8. Remove the rear attachment screws, gearbox. Shown in the figure Location of

gearbox on page xx.

Action Note/Illustration

3. Fit a new sealing, axis 2 to the gearbox. Art. no. is specified in Required

equipment on page xx.

How to read the product manual

3HAC020993-001 Revision: G16

1 Safety

1.1. Introduction

173HAC020993-001 Revision: G

1 Safety

1.1. Introduction

Overview

The safety information in this manual is divided in two categories:

• general safety aspects, important to attend to before performing any service work on

the robot. These are applicable for all service work and are found in section General

safety information on page 18.

• specific safety information, pointed out in the procedure at the moment of the danger.

How to avoid and eliminate the danger is either detailed directly in the procedure, or

further detailed in separate instructions, found in section Safety related instructions on

page 35.

1 Safety

1.2.1. Safety in the robot system

3HAC020993-001 Revision: G18

1.2 General safety information

1.2.1. Safety in the robot system

Validity and responsibility

The information does not cover how to design, install and operate a complete system, nor

does it cover all peripheral equipment, which can influence the safety of the total system. To

protect personnel, the complete system must be designed and installed in accordance with the

safety requirements set forth in the standards and regulations of the country where the robot

is installed.

The users of ABB industrial robots are responsible for ensuring that the applicable safety laws

and regulations in the country concerned are observed and that the safety devices necessary

to protect people working with the robot system are designed and installed correctly.

Personnel working with robots must be familiar with the operation and handling of the

industrial robot, described in the applicable documents, e.g.

• User’s Guide - S4Cplus (M2000)

• Operating Manual - IRC5 with FlexPendant (M2004)

• Product Manual

Connection of external safety devices

Apart from the built-in safety functions, the robot is also supplied with an interface for the

connection of external safety devices. Via this interface, an external safety function can

interact with other machines and peripheral equipment. This means that control signals can

act on safety signals received from the peripheral equipment as well as from the robot.

Limitation of liability

Any information given in this manual regarding safety, must not be construed as a warranty

by ABB that the industrial robot will not cause injury or damage even if all safety instructions

are complied with.

Related information

Type of information Detailed in document Section

Installation of safety

devices

Product manual for the robot Installation and commissioning

Changing operating

modes

User’s guide - S4Cplus

(RobotWare 4.0)

Operating manual - IRC5 with

FlexPendant (RobotWare 5.0)

Start-up

Operating modes

Restricting the working

space

Product manual for the robot Installation and commissioning

Page is loading ...

ABB IRB 6650S - 125/3.5 User manual

This manual is also suitable for

ABB IRB 6650S - 125/3.5 User manual

Related papers

Other documents