Tyan S2727 User manual

1

http://www.TYAN.com

Tiger GC-SL

///

S2727

Revision 1.01

may be reproduced or translated without prior written consent from TYAN Computer Corp.

All registered and unregistered trademarks and company names contained in this manual are

property of their respective owners including, but not limited to the following.

TYAN, Tiger GC-SL S2727 are trademarks of TYAN Computer Corporation.

Intel, Pentium, and combinations thereof are trademarks of Intel Corporation.

Adaptec is a trademark of Adaptec, Incorporated.

AMI, AMIBIOS are trademarks of American Megatrends, Incorporated.

Microsoft, Windows are trademarks of Microsoft Corporation.

National is a trademark of National Semiconductor.

Promise is a trademark of Promise Technology.

IBM, PC, AT, and PS/2 are trademarks of IBM Corporation.

Winbond is a trademark of Winbond Electronics Corporation.

Portable Document Format (PDF) is a trademark of Adobe Corporation.

Information contained in this document is furnished by TYAN Computer Corporation and has been

reviewed for accuracy and reliability prior to printing. TYAN assumes no liability whatsoever, and

disclaims any express or implied warranty, relating to sale and/or use of TYAN products including

liability or warranties relating to fitness for a particular purpose or merchantability. TYAN retains the

right to make changes to product descriptions and/or specifications at any time, without notice. In

no event will TYAN be held liable for any direct or indirect, incidental or consequential damage,

loss of use, loss of data or other malady resulting from errors or inaccuracies of information

contained in this document.

2

http://www.TYAN.com

Before you begin…

Chapter 1: Introduction

1.1 Congratulations!

1.2 Specifications

Chapter 2: Board Installation

2.0 Board Image

2.1 Board Parts

2.2 Jumper Setting List

2.3 Connector List

2.4 Front Panel Connector

2.5 Clear CMOS

2.6 Onboard ATI RAGE XL Graphics

2.7 Onboard Intel 82551QM LAN

2.8 Ext. Intel 82551 LAN LED Header

2.9 Onboard Intel 82540EM LAN

2.10 Ext. Intel 82540 LAN LED Header

2.11 CPU Thermal-Trip

2.12 CPU-Hot Warning LED For CPU1

2.13 CPU-Hot Warning LED For CPU2

2.14 Watchdog Timer Control

2.15 Fan Connectors

2.16 Serial Header (COM2)

2.17 USB Header

2.18 Mounting the Motherboard

2.19 Xeon Reinforcement Kit Installation

2.20 Installing the Processors & Heatsinks

2.21 Installing the Memory

2.22 Attaching Drive Cables

2.23 Installing Add-In Cards

2.24 Connecting External Devices

2.25 Installing the Power Supply

2.26 Finishing UP

Chapter 3: BIOS

3.1 BIOS Menu Bar

3.2 BIOS Legend Bar

3.3 BIOS Main Menu

3.4 BIOS Advanced Menu

3.5 BIOS PCI/PnP Menu

3.6 BIOS Boot Menu

3.7 BIOS Chipset Menu

3.8 BIOS ACPI Menu

3.9 BIOS Security Menu

3.10 BIOS Exit Menu

Chapter 4: Diagnostics

4.1 Beep Codes

4.2 Flash Utility

Appendix I: Glossary

Appendix II: SMDC Information

Appendix III: S2727 With Tyan Riser Cards

Technical Support

……………………………………………..Page 3

..……………………………………………Page 4

……………………………………………..Page 4

….….………………………………………Page 6

……………………………………………..Page 7

……………………………………………..Page 8

……………………………………………..Page 9

………………….………………………..Page 10

……………………………………………Page 11

……………………………………………Page 12

……………………………………………Page 13

……………………………………………Page 14

……………………………………………Page 15

……………………………………………Page 16

……………………………………………Page 17

……………………………………………Page 18

……………………………………………Page 19

……………………………………………Page 21

……………………………………………Page 22

……………………………………………Page 24

……………………………………………Page 26

……………………………………………Page 27

……………………………………………Page 28

……………………………………………Page 29

……………………………………………Page 30

……………………………………………Page 31

……………………………………………Page 32

……………………………………………Page 33

……………………………………………Page 36

……………………………………………Page 38

……………………………………………Page 39

……………………………………………Page 40

……………………………………………Page 41

……………………………………………Page 42

……………………………………………Page 43

……………………………………………Page 44

……………………………………………Page 45

……………………………………………Page 50

……………………………………………Page 51

……………………………………………Page 52

3

http://www.TYAN.com

Before you begin…

Check the box contents!

The retail motherboard package should contain the following:

1x Tiger GC-SL motherboard

2x CPU retentions

2x CPU Retention Reinforcement back-plates with screws

1x 34-Pin floppy drive cable

1 x Ultra-DMA-133/100/66/33 IDE cable

1x Tiger GC-SL User’s Manual

1x Tiger GC-SL Quick Reference (sticker)

1x TYAN driver CD

1x I/O shield

If any of these items are missing, please contact your vendor/dealer for replacement before

continuing with the installation process.

4

http://www.TYAN.com

Chapter 1: Introduction

1.1 – Congratulations!

You have purchased one of the most powerful dual Intel processor solutions, the Tiger GC-SL

S2727. Based on Serverworks Grand Champion SL chipset, the Tiger GC-SL S2727 is Hyper-

Threading ready - utilizing onboard resources so that a second thread of data can be processed in

a single processor. Compatible with both ATX12V and EPS12V power supplies, this platform

offers convenient remote Intelligent Platform Management Interface (IPMI) monitoring through a

Server Management Daughter Card. The Tiger GC-SL S2727 also features an ATX form factor,

64-bit PCI, Gigabit Ethernet port, Fast Ethernet port, and an onboard ATI 8MB PCI RAGE XL

VGA, which provides an advanced and versatile solution for your server needs.

Remember to visit Tyan’s web site at http://www.tyan.com. There you can find information on all of

Tyan’s products with FAQs, a complete distributors list, and BIOS setting explanations.

1.2 – Specifications

Processor

• Dual mPGA604 ZIF Sockets

• Supports one or two Intel Xeon processors

with 512KB of integrated L2 cache

• Onboard 4-phase VRM (VRM 9.1 spec)

• Front-Side Bus support for 533 & 400 MHz

Chipset

• ServerWorks GC-SL chipset

• CMIC-SL, CSB6

• National PC87417 Super I/O

• Winbond W83782D Hardware Monitor ASIC

Memory

• Four DDR DIMM sockets (minimum one single

DIMM)

• Supports up to 4GB maximum memory

• Supports Registered ECC DDR (72-bit)

memory modules

Expansion Slots

• Three 64/32-bit/33MHz PCI 2.2 slots

• Two 32-bit/33MHz PCI 2.2 slots

• Total five usable slots

Integrated PCI IDE

• Triple-channel PCI bus-master mode

• The primary and secondary channels support

ATA -100/66/33 IDE and ATAPI compliant

devices.

• The tertiary channel supports ATA - 66/33 IDE

and ATAPI compliant devices.

• Supports up to six Enhanced IDE devices

Integrated LAN Controller(s)

Two or one onboard Ethernet NICs

• Intel 82540EM Gigabit Ethernet controller

(not included with S2727GN version)

• One RJ-45 LAN connector with LEDs

• Operating at a 32-bit 33 MHz PCI bus

• Intel 82551QM Fast Ethernet controller

• One RJ-45 LAN connector with LEDs

• Operating at a 32-bit 33 MHz PCI bus

Intelligent Platform Management Interface

(with optional Tyan’s M3289 SMDC)

• QLogic Zircon Baseboard Management

Controller (BMC) based on powerful ARM7

technology

• Tailored for IPMI highest 1.5 specifications

• Supports KCS and BT styles

• Supports flexible Windows and Linux based

Management Solution

• Supports RMCP and SNMP protocols

• Supports ASF standard and EMP

• I

2

C serial multi-master controllers and

UARTs

• Built-in IPMB connector

• Supports remote Power on/off and reset

support (IPMI-over-LAN)

• Server Management Daughter card

connection via a built-in 2x25 header

Integrated 2D/3D Graphics

• ATI RAGE XL graphics controller

• 8MB frame buffer (SDRAM)

• Standard 15-pin analog VGA port

5

http://www.TYAN.com

Integrated I/O

• One floppy connector supports up to two drives

• Two 9-pin 16550-based serial ports

(COM2 via an optional cable)

• One 25-pin SPP/ECP/EPP parallel port header

• Four USB ports (2 rear connectors and 2 front

side USB headers for an optional cable)

• PS/2 keyboard and mouse connetors

System Management

• Winbond W83782D or optional ADI ADM1027

• Total six 3-pin fan headers with tachometer

monitoring

• Three 3-pin fan headers and PWM control

• 2-pin chassis intrusion header

• Temperature and voltage monitoring

• Watchdog timer

BIOS

• AMI BIOS on 4Mbit Flash ROM

• Supports ACPI

• Auto detection of memory size

• Auto configuration of IDE hard drive types

• Multiple boot options

• User settings of hardware monitoring

• Power Management: ACPI S1, S4, and S5

Form Factor

• Standard ATX 2.03 (12” x 9.6”), 6-layer PCB

• ATX12V/EPS12V power connector

• Stacked Mouse/Keyboard Ports

• Stacked USB (two) connectors

• One serial connector and one VGA connector

• Two RJ-45 side-by-side connectors with

LEDs (S2727GN version has only one RJ-45.)

Regulatory

• FCC DoC (Declaration of Conformity)

• European CE (Declaration of Conformity)

Hyper-Threading Support In:

Windows 2000 Server

Windows 2000 Advanced Server

Windows XP Pro

Windows NT 4.0 Server

Linux (Kernel 2.4.18)

Novell Netware 6 with Support Pack 1

TYAN reserves the right to add support or

discontinue support for any OS with or

without notice.

6

http://www.TYAN.com

Chapter 2: Board Installation

Installation

You are now ready to install your motherboard. The mounting hole pattern of the Tiger GC-SL

matches the ATX specifications. Before continuing with installation, confirm that your chassis

supports a standard ATX motherboard. Two CPU retention reinforcement back-plates are

included for securing the CPU heatsinks.

How to install our products right…. the first time!

The first thing you should do is read this user’s manual. It contains important information that will

make configuration and setup much easier. Here are some precautions you should take when

installing your motherboard:

(1) Ground yourself properly before removing your motherboard from the antistatic bag.

Unplug the power from your computer power supply and then touch a safely grounded

object to release static charge (i.e. power supply case). For the safest conditions, Tyan

recommends wearing a static safety wrist strap.

(2) Hold the motherboard by its edges and do not touch the bottom of the board, or flex the

board in any way.

(3) Avoid touching the motherboard components, IC chips, connectors, memory modules,

and leads.

(4) Place the motherboard on a grounded antistatic surface or on the antistatic bag that the

board was shipped in.

(5) Inspect the board for damage.

The following pages include details on how to install your motherboard into your chassis, as well

as installing the processor, memory, disk drives and cables.

NOTE DO NOT APPLY POWER TO THE BOARD IF IT HAS BEEN DAMAGED

7

http://www.tyan.com

2.0 – Board Image

The following is an image of the S2727 Tiger GC-SL.

The above photograph is purely representative. Due to engineering updates and new board

revisions, certain components may change and or be repositioned. The picture above may

or may not look exactly like the board you received.

The following page includes details on the vital components of this motherboard.

8

http://www.tyan.com

2.1 – Board Parts

This jumper diagram is representative of the latest board revision available at the time of

publishing. The board you receive may or may not look exactly like the above diagram.

The board parts are not to scale.

9

http://www.tyan.com

2.2 – Jumper Settings

Jumper Function Settings Ref. Page

JP1

CMOS Clear

Open: Normal (Default)

Close: CMOS Clear Mode

Page 11

JP20

Reserved

Page 11

JP23

Enable/Disable CPU Thermal-

trip power down feature

Open: Enable (Default)

Close: Disable

Page 11

JP24

Enable/Disable onboard Intel

82551QM Fast Ethernet NIC

Open: Enable (Default)

Close: Disable

Page 12

JP31

Enable/Disable onboard ATI

Rage XL PCI VGA controller

Open: Enable (Default)

Close: Disable

Page 14

JP35

Enable/Disable onboard Intel

82540EM Gigabit Ethernet NIC

Open: Enable (Default)

Close: Disable

Page 13

2.3 – Connectors

Connector Function

J1

External LED header for Processor-hot warning; same as onboard LED D1

J21

PS/2 keyboard (lower) and PS/2 mouse (upper) connectors

J22

Front panel header

J26

RJ45 LAN connector for onboard Intel 82551QM NIC

J27

VGA connector for onboard ATI Rage XL PCI VGA

J30

Front USB headers

J32

Hardware monitor warning buzzer header (optional)

J33

RJ45 LAN connector for onboard Intel 82540EM NIC

J36

External speaker header

J38

Auxiliary LAN LED header for onboard Intel 82540EM NIC

J40

Auxiliary LAN LED headers for onboard Intel 82551QM NIC

COM2

COM2 2x5 pin header

CPUFAN1

3-pin CPU1 fan connector with PWM fan control and fan speed reading

CPUFAN2

3-pin CPU2 fan connector with PWM fan control and fan speed reading

FAN3

3-pin fan connector with PWM fan control and fan speed reading

FAN4

3-pin fan connector with PWM fan control and fan speed reading

FAN5

3-pin CPU fan connector with fan speed reading

FAN6

3-pin fan connector with PWM fan control and fan speed reading

10

http://www.tyan.com

Jumper Legend

Jumper OFF (without jumper cap)

Jumper ON (with a jumper shunt to cover the jumper pins)

2.4 – Front Panel Connector (J22)

Your chassis will usually come with connectors to install onto the motherboard, such as HDD and

Power LEDs. The Front Panel Connector (J22) has been implemented for such purposes.

J22

Front Panel Connector

Pin 1: Hard disk drive LED +

Pin 2: Power LED +

Pin 3: Hard disk drive LED -

Pin 4: Power LED -

Pin 5: GND

Pin 6: Power button (LOW asserted)

Pin 7: Reset button (LOW asserted)

Pin 8: GND

Pin 9: +5V

Pin10: Sleep button (LOW asserted)

Pin11: NC (Not Connected)

Pin12: GND

Pin13: GND

Pin14: Key

Pin15: NC (Not Connected)

Pin16: NC (Not Connected)

Pin17: Chassis intrusion (LOW asserted)

Pin18: GND

11

http://www.tyan.com

2.5 – Clear CMOS (JP1)

2.6 – Onboard ATI



RAGE XL Graphics (JP31)

JP1

CMOS Reset

(OPEN)

(CLOSE)

Normal (default) Clear CMOS

You can reset the CMOS settings in case an

incorrect setting causes system instability or

you have forgotten your system/setup

password or have just flashed your BIOS by

using these jumpers.

• Power off system and disconnect the AC

power from the power supply.

• Set jumper JP1 to Clear CMOS.

• Power system on and wait for the screen

to show this message: “CMOS Settings

Wrong, CMOS Checksum Bad”. Now the

CMOS is cleared.

• Power off system and disconnect the AC

power from the power supply and set

jumper JP1 to Normal (OPEN) for normal

operations.

• Power system on and go to BIOS Setup.

Load and save setup defaults.

JP31

Onboard ATI



RAGE XL Graphics

(OPEN)

(CLOSE)

Enabled (Default) Disabled

OPEN: The jumper enables the onboard ATI

RAGE XL graphics controller. You can also use

the onboard video in conjunction with another

PCI graphics card for multiple monitor support.

CLOSE: The jumper disables the onboard ATI

RAGE XL graphics controller.

12

http://www.tyan.com

2.7 – Onboard Intel

®

82551QM Fast Ethernet Controller (JP24)

2.8 – External LAN LED Header for onboard Intel 82551QM LAN (J40)

JP24

Onboard Intel

®

82551QM (LAN1)

(OPEN)

(CLOSE)

Enabled (Default) Disabled

The onboard LAN1, Intel 82551QM Fast

Ethernet controller, with its RJ-45 (J26, next to

VGA connector in the rear I/O.) can be enabled

or disabled by JP24.

OPEN: The jumper enables the onboard Intel

82551QM 10/100 Mbps Fast Ethernet controller.

CLOSE: The onboard Intel 82551QM 10/100

Mbps Fast Ethernet controller can be disabled

by placing a jumper shunt on jumper JP24.

J40

Onboard Intel

®

82551QM (LAN1)

J40 is a 4-pin external LAN LED header for

onboard LAN1 / Intel 82551QM controller.

The LED indication is similar to the LEDs on J26.

LED indications:

Pin 1: Yellow LED +

Pin 2: Yellow LED -

Pin 3: Green LED +

Pin 4: Green LED -

Link not established:

Yellow LED: Off Green LED: Off

Link at 10Mbps without activity

Yellow LED: Off Green LED: On

Link at 10Mbps with activity

Yellow LED: Off Green LED: Blink

Link at 100Mbps without activity

Yellow LED: On Green LED: Off

Link at 100Mbps with activity

J40

Yellow LED: Blink Green LED: Off

13

http://www.tyan.com

2.9 – Onboard Intel

®

82540EM Gigabit Ethernet Controller (JP35)

2.10 – External LAN LED Header for onboard Intel 82540EM LAN (J38)

JP35

Onboard Intel

®

82540EM LAN2 (for S2727GNN only)

(OPEN)

(CLOSE)

Enabled (Default) Disabled

The onboard LAN2, Intel 82540EM Gigabit

Ethernet controller, with its RJ-45 (J33) can be

enabled or disabled by JP35.

OPEN: The jumper enables the onboard Intel

82540EM10/100/1000 Mbps Ethernet controller.

CLOSE: The onboard Intel 82540EM

10/100/1000 Mbps Ethernet controller can be

disabled by placing a jumper shunt on jumper

JP35.

J38

Onboard Intel

®

82540EM LAN2

J38 is a 4-pin external LAN LED header for

onboard LAN2/Intel 82540EM Gigabit controller.

The LED indication is similar to the LEDs on J33.

LED indications:

Pin 1: Yellow LED +

Pin 2: Yellow LED -

Pin 3: Green LED +

Pin 4: Green LED -

Link not established:

Yellow LED: Off Green LED: Off

Link at 10Mbps without activity

Yellow LED: Off Green LED: On

Link at 10Mbps with activity

Yellow LED: Off Green LED: Blink

Link at 100Mbps without activity

Yellow LED: On Green LED: Off

Link at 100Mbps with activity

Yellow LED: Blink Green LED: Off

Link at 1000Mbps without activity

Yellow LED: On Green LED: On

Link at 1000Mbps with activity

J38

Yellow LED: Blink Green LED: Blink

14

http://www.tyan.com

2.11 – CPU Thermal-Trip (JP23)

The processor protects itself from overheating by the use of an internal integrated thermal sensor.

When the Thermal-Trip is enabled, the system will shut off if temperature reaches about 135º

Celsius at CPU junction temperature. The processor then stops all its executions.

2.12 – CPU-Hot Warning LED Header For CPU1 (J1)

JP23

CPU Thermal-Trip Protection

(OPEN)

(CLOSE)

Enabled (Default) Disabled

OPEN: CPU Thermal-Trip Protection is enabled.

CLOSE: CPU Thermal-Trip Protection is

disabled. System will not be forced to shut off,

when CPU Thermal-Trip occurs. In this case,

overheating could damage the processor.

J1

CPU-Hot Warning LED Header For CPU1

Pin 1: LED +

J1

Pin 2: LED -

J1 is an external LED header to indicate CPU1

signal PROCHOT# status. When CPU1 gets

too hot, the CPU1 signal PROCHOT# will be

asserted before CPU1 reaches cataclysmal

failure or damage.

The onboard LED (D1) acts as same as J1 to

indicate CPU1 processor overheating.

15

http://www.tyan.com

2.13 – CPU-Hot Warning LED Header For CPU2 (J44)

J44

CPU-Hot Warning LED Header For CPU2

Pin 1: LED +

J44

Pin 2: LED -

J44 is an external LED header to indicate CPU2

signal PROCHOT# status. When CPU2 gets

too hot, the CPU2 signal PROCHOT# will be

asserted before CPU2 reaches cataclysmal

failure or damage.

The onboard LED (D2) acts as same as J44 to

indicate CPU2 processor overheating.

16

http://www.tyan.com

2.15 – Fan Connectors

Use these headers to connect cooling fans, both chassis and processor

fans, to your motherboard. Cooling fans help keep the system more

stable and operating reliably for its product life.

+12Volts fans supported

FAN PWM Fan Control Fan Tachometer/Speed Reading Max. Current

CPUFAN1

No Yes 1.5 Amp

CPUFAN2

No Yes 1.5 Amp

FAN3

Yes Yes 1.2 Amp

FAN4

Yes Yes 1.2 Amp

FAN5

Yes Yes 1.2 Amp

FAN6

No Yes 1.5 Amp

2.16 – Serial Port Header (COM 2)

COM2

The Second Serial Port Header

Pin 1: DCD

Pin 2: RXD

Pin 3: TXD

Pin 4: DTR-

Pin 5: GND

Pin 6: DSR

Pin 7: RTS

Pin 8: CTS

Pin 9: RI

Pin10: NC

17

http://www.tyan.com

2.17 – USB Header (J30)

J30

USB #2 & #3 Header

Pin 1: USB POWER

Pin 2: GND

Pin 3: USB_3-

Pin 4: GND

Pin 5: USB_3+

Pin 6: USB_2+

Pin 7: GND

Pin 8: USB_2-

Pin 9: GND

Pin10: USB POWER

Note:

The external USB cable is optional and not

included in the standard shipping box.

18

http://www.tyan.com

2.18 – Mounting the Motherboard

Before installing your motherboard, make sure your chassis has the necessary motherboard

support studs installed. These studs are usually metal and are gold in color. Usually, the chassis

manufacturer will pre-install the support studs.

- Memory Type: Tiger GC-SL S2727 only supports Registered DDR memory with ECC.

Non-Registered or non-ECC DDR memory modules are NOT supported. The board supports

single DIMM operation. Hence, the minimum memory module is one memory DIMM to allow

system to boot up.

- CPU Front-Side Bus Speed Match: The S2727 Tiger GC-SL memory frequency is

synchronized with both CPU and onboard memory controller front-side bus, which means the

memory module speed rate should match the CPU FSB. For example, with an Intel Xeon

533MHz Front-Side Bus (FSB) processor, the memory only supports DDR266/PC2100 Registered

ECC DIMM modules.

Below is a chart detailing what the most common motherboard studs look like and how they

should be installed.

TIP: Use metal studs if possible, as they hold the motherboard into place more securely than

plastic standoffs.

19

http://www.tyan.com

2.19 – Installation Guide of Xeon Processor Reinforcement Kit (CPU Back-plates)

The processors heatsinks should be installed with the provided Xeon Processor Reinforcement

Kit. Follow this installation guide, before installing the processors.

1. Check the parts in the kit: two back-plates and 9 screws.

(Four screws for each plate and one spare screw.)

2. The back-plates must be installed prior to installing the motherboard into a chassis.

3. Ensure that the screws have firmly secured the motherboard between the CPU

heatsink retention bases and the back-plates.

The following diagrams will illustrate how to install the included heatsink retention modules:

1) Align the heatsink mounting bracket to the holes around the processor socket

2) Insert Black securing peg (use the screws instead and skip step 5, if install with the

CPU reinforcement kit) into bracket holes

3) Insert White locking peg into Black securing peg

4) Repeat process to mount all other brackets

20

http://www.tyan.com

5) Seat heatsink between brackets on processor

6) Attach heatsink clips

Page is loading ...

Tyan S2727 User manual

This manual is also suitable for

Tyan S2727 User manual

Related papers

Other documents