Matsui MFI60 Installation guide
- Category
- Dishwashers
- Type
- Installation guide
MFI60
1
Carefully read this manual before installation
Reading this manual will help to understand the connections of inlet, drain hoses and
power cord, and to find a optimal position for the dishwasher.
Notes
●
The installation of the pipes
and electrical equipment
should be made by a qualified
person.
Electrical Shock Hazard
Disconnect electrical
p
ower before
carrying out any re-wiring.
Failure to do so can result in death or
electrical shock.
The installation
p
osition of the dishwasher should be near the existin
g
inlet ,drain hoses and
power cord.
One side of the cabinet sink should be chosen to facilitate the connection of drain hoses of
the dishwasher.
Pre
p
arations should be made before movin
g
the dishwasher to the installation
p
lace.
Choose a
p
lace near the sink to facilitate the installation of inlet and drain hoses
(see Figure 1).
If dishwasher is installed at the corner of the cabinet, there should be some s
p
ace
(see Figure 2) when the door is opened.
2
1
Installation preparation
Installation instruction
Note:
p
lease check the accom
p
an
y
in
g
installation accessories are
p
rovided.
●
●
2
Minimum space when
the door is opened
【Figure2】
Cabinet dimensions
【Figure1】
Cabinet
Dishwasher
Door of
dishwasher
Minimum s
p
ace of 50mm
1
The aesthetic
p
anel should be
p
rocessed accordin
g
to the Fi
g
ure 3.
The aesthetic panel should
be processed in accordance
with the illustrated dimensions
【Figure3】
●
Aesthetic panel's dimensions and installation
Less than 5mm
between the top
of dishwasher and
cabinet and the
outer door aligned
to cabinet.
90 °
90 °
600 mm
820mm
100
580mm
80
Space between cabinet
bottom and floor
Electrical, drain and
water supply line
entrances
(Unit: mm)
680
594
540 ± 0.2
568 ± 0.2
499 ± 0.2
172.5 ± 0.2
65
15
2
x
φ
2
H
o
l
e
d
e
e
p
1
0
254 ± 0.2 250 ± 0.2
2
x
φ
2
H
o
l
e
d
e
e
p
1
0
1.5
19
38
7
30
44
52
2
x
φ
2
H
o
l
e
d
e
e
p
1
0
3
To hel
p
assist the installation of the aesthetic
p
anel a tem
p
late has been
p
rovided to show
where the bracket and holes need to be marked.
Measure the corresponding dimentions on the template. Align the template card to one edge
of the door. With the correct line a
g
ainst the ed
g
e of the door mark the hole
p
ositions for that
side, repeat this on the other side of the door.
●
Installation of the aesthetic panel
TOP
edge of the board
Door top edge
4
Installation of aesthetic panel
【Figure4a】
2
Install the hook on the aesthetic wooden
p
anel and
p
ut the hook into the slot of the outer door of
dishwasher
(
see Fi
g
ure 4a
)
. After
p
ositionin
g
of the
p
anel, fix the
p
anel onto the outer door usin
g
the screws provided(see Figure 4b) .
Installation of
aesthetic panel
【Figure4b】
Ho
p
hook
St4 countersunk
head screw
Lower hook
Outer door of
dishwasher
Aesthetic
p
anel
Hook for aesthetic
p
anel
4X18 screw
S
p
acer for aesthetic
p
anel
Cover
1
2
3
. Remove plaslic covers
. Secure panel with
provided screws
. Replace plaslic covers
5
qualified plumber.
maximum of 10 bars.
Make sure your plumbing is suitable to install
your new dishwasher. If in doubt contact a
The water pressure coming from the water
mains supply must be a minimum of 0.4 and a
First connect water inlet hose to your
dishwasher Ensure black rubber seal is
in place.
Then connect the straight end to your water
mains supply Ensure black rubber seal is
in place.
Please turn on the tap and check for leakages
after connecting the hose.
Please ensure the tap is turned off when the
machine is not used.
If you only have one cold water
feed (For example for your
washing machine don't worry.
a Y adaptor will provide you with
the additional cold water feed
you need for your dishwasher.
Y adaptor is available from most
DIY stores.
max 100 cm
min 40 cm
min 4cm
max 100 cm
12cm
Fit the drainage hose of your machine
to the drainage pipe without bending.
washing process.
Secure your hose firmly to the waste
pipe to avoid it coming off during the
drainage system.
The waste pipe must only be connected
into the foul drains and not surface water
The hose should be placed between
40 cm and 100 cn from the floor level
and must not be extended otherwise the
machine may not empty the waste water.
6
Tension ad
j
ustment
of the door spring
【Figure5】
Tension ad
j
ustment of the door s
p
rin
g
●
●
The door s
p
rin
g
s are set at the factor
y
to the
p
ro
p
er tension for the outer door. If aesthetic
panel is installed, you will have to adjust the door spring tension. Rotate the adjusting
screw to drive the adjustor to strain or relax the steel cable (see Figure 5).
Insert the drain hose into a drain
p
i
p
e with a minimum diameter of 4cm, or let it
run into the sink, making sure to avoid bending or crimping it. Use the speical
p
lastic su
pp
ort that comes with the a
pp
liance
(
Fi
g
ure 6
)
. The free end of the hose
must be at a height between 400 and 1000mm and must not be immersed in water
to avoid back flow. ATTENTION: The special plastic hose support must be tightly
fastened to the wall toprevent the drain hose from moving and allowing water to
spill outside the drain.
Drain pipe connection
【Figure6】
Drain hose hook
Min 400mm
Max 1000mm
φ40mm
7
Dishwasher installation steps
●
.
.
.
1
2
3
4
5
7
10
Install the aesthetic door to the outer door of the dishwasher usin
g
the brackets
p
rovided. Refer
to the template for positioning of the brackets.
Adjust the tension of the door springs by using an Allen key turning in a clockwise motion to
ti
g
hten the left and ri
g
ht door s
p
rin
g
s. Failure to do this could cause dama
g
e to
y
our dishwasher
(Figure 2)
Connect the inlet hose to the cold water supply
Connect the drain hose. (Figure 6)
Connect the power cord
Put the dishwasher to slide rails (Figure 4)
Add the condensation strip following instructions on the reverse side of the condensation strip
Place the dishwasher into position.
Level the dishwasher. The rear feet can be adjusted from the front of the dishwasher by turning
the screws on the left and ri
g
ht hand side of the cabinet
(
Fi
g
ure 6A
)
. To ad
j
ust the front feet,
use a spanner and turn the front feet until the dishwasher is level (Figure 6B).
The dishwasher must be secured in place. There are two ways to do this:
A. Normal work surface-secure to the work surface by using two woodscrews ensuring the
dishwasher weight is not being hit by the surface (Figure 7).
B. Marble or granite work top-secure the bracket to the side panel of the dishwasher and secure
the dishwasher to the furniture housing. Put the rubber cap over the screw (Figure 8).
6
8
9
.
.
6
4
5
A
e
s
t
h
e
t
i
c
d
o
o
r
7
2
RUBBER
SCREW
COVER
8
SCREW
CONE GEAR
6B
6A
8
1
Unscrew ad
j
ust the distance of left and ri
g
ht
p
linth tab to
y
our need.
The adjustable range is from 39mm to 134mm. [Figure a]
the two screws and
●
Installation the plinth
2
Fix the
p
linth on the
p
linth tab. Accordin
g
to
y
our need to ad
j
ust the
p
linth hei
g
ht, the
adjustable range is from 56mm to 122mm. [Figure b]
[Figure a]
[Figure b]
plinth
plinth tab
122
56
9
●
Attention
Illustration of feet adjustment
Check Level
Side To Side
Check
Level
Front
to Back
The dishwasher must be level for the racks to o
p
erate correctl
y
and to
g
ive maximum wash
performance.
Place a s
p
irit level on the door and the lower rack rail as shown in dia
g
ram 1 to check that
the dishwasher is level.
It is eas
y
to level the dishwasher b
y
ad
j
ustin
g
the four levelin
g
le
g
s individuall
y
from the front
of the dishwasher.
2.1 Refer to Remark A dia
g
ram 2 below for ad
j
ustment of the rear le
g
s,turn the screw clockwise to
lower the rear legs until the correct height is obtained.
2.2 Refer to Remark B diagram 2 below adjustment of the front legs to obtain the correct height.
leveling the dishwasher be careful not to allow the dishwasher to
1
2
3
When tip over.
After installation, please put this installation manual in a safe place.The content
of this manual is very helpful to users who may be unfamiliar with the appliance.
【Figure 8】
1
2
Remark A: adjust the height
of back foot with a screwdriver.
Remark B: adjust the height
of front foot with a spanner.
●
Start of dishwasher
The dishwasher is level and fixed.
The inlet valve is opened.
The connections not leaking.
Drainage hose has been fitted.
The power is switched on.
The inlet and drain hoses are not tra
pp
ed or kinked.
All
p
ackin
g
materials and documents should be taken out from the dishwasher.
1
2
3
4
5
6
7
The following should be checked before starting the dishwasher.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
Matsui MFI60 Installation guide
- Category
- Dishwashers
- Type
- Installation guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI