2. Invacare
  3. MK6i Series
MK6i Series

Invacare MK6i Series User manual

  • Hello! I am an AI chatbot trained to assist you with the Invacare MK6i Series User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • What are the potential dangers associated with using the Invacare MK6i Mini Color Display?
    Who should perform the installation of the MK6i Mini Color Display?
    What steps should be taken before performing any adjustments, repairs, or service on the wheelchair?
    What accessories are compatible with the Invacare MK6i Mini Color Display?
    How can I save programming settings onto the Basic Memory Card?
    How do I remove the existing display?
    How do I install the MK6i Mini Color Display?
    How do I secure the cables after installation?
    How can I program the MK6i Mini Color Display?
Part No 1171901 1 MK6i® Mini Color Display
1 General
1.1 Symbols
Signal words are used in this manual and apply to hazards or unsafe practices which could result in
personal injury or property damage. See the information below for definitions of the signal words.
2 Safety
WARNING
Warning indicates a potentially hazardous situation which, if not avoided, could
result in death or serious injury.
CAUTION
Caution indicates a potentially hazardous situation which, if not avoided, may result
in property damage or minor injury or both.
Gives useful tips, recommendations and information for efficient, trouble-free use.
Check all parts for shipping damage. In case of damage, DO NOT use. Contact
Carrier/Invacare for further instructions.
To ensure the safe installation of the MK6i Mini Color Display, these instructions
must be followed.
WARNING
DO NOT use this product or any available optional equipment without first
completely reading and understanding these instructions and any additional
instructional material such as owner’s manuals, service manuals or instruction
sheets supplied with this product or optional equipment. If you are unable to
understand the warnings, cautions or instructions, contact a healthcare
professional, dealer or technical personnel before attempting to use this equipment
- otherwise, injury or damage may occur.
This procedure MUST be performed by a qualified technician.
Make sure wheelchair is Off and user is removed from wheelchair before
performing this procedure.
After any adjustments, repair or service and before use, make sure all attaching
hardware is tightened securely - otherwise injury or damage may result.
MK6i® Mini Color Display
Service Manual
DEALER: Keep this manual. The procedures in this manual MUST
be performed by a qualified technician.
MK6i® Mini Color Display 2 Part No 1171901
3 Overview
3.1 Kit Contents
Mk6i Mini Color Display
Mk6i Mini Color Display Service Manual, part number 1171901
Power Wheelchair Wiring Guide, part number 1167603
MK6i Electronics Field Reference Guide, part number 1141471
10 Tie-wraps
3.2 Installation Overview
To install the MK6i Mini Color Display, perform the following procedures:
Save programming settings (optional)
Remove the existing display.
Disconnect the existing display.
Install the MK6i mini color display.
Connect the MK6i mini color display.
Secure the cables.
Program the MK6i mini color display.
4 Usage
4.1 Save Programming Settings
Saving Programming Settings Onto the Basic Memory Card
1. Insert the memory card into the existing display.
2. Turn the wheelchair On.
3. Use the up/down arrows to select STORE TO CARD.
4. Press the Select key.
Saving Programming Settings Onto the Professional Memory Card
1. Insert the memory card into the existing display.
2. Turn the wheelchair On.
3. Use the up/down arrows to select MEMORY CARD.
4. Select SYSTEM.
5. Select SAVE.
6. Select FOLDER.
7. Select the desired folder to save to.
8. Select NAME.
9. Select the desired system to save.
10. Select START.
ACCESSORIES WARNINGS
Invacare products are specifically designed and manufactured for use in conjunction
with Invacare accessories. Accessories designed by other manufacturers have not
been tested by Invacare and are not recommended for use with Invacare products.
For these procedures, refer to FIGURE 1 on page 4.
Part No 1171901 3 MK6i® Mini Color Display
4.2 Remove the Existing Display
1. Loosen the screw A securing the mounting clamp B.
2. Remove the existing display (not shown) from the mounting clamp.
3. Note the location of tie-wraps securing the existing display cable.
4. Cut the tie-wraps securing the existing display cable.
4.3 Disconnect the Existing Display
1. Verify the display On/Off switch is in the Off position.
2. Pull the latches C away from the display network connector D and the connectors above and
below.
3. Disconnect and remove the display connector from the remaining connectors
4.4 Install the MK6i Mini Color Display
1. Insert the mini color display E into the mounting clamp B.
2. Tighten the screw A to secure the mini color display into the mounting clamp.
4.5 Connect the Mini Color Display
1. Ensure the latch C is pulled away from the network connector F.
2. Connect the network connector to the other connectors.
3. Top and Bottom Connectors - Install connector caps G onto the network connector.
4. Push the latches in to secure the network connectors and caps.
4.6 Secure the Cable
1. Use tie-wraps to secure the cable in the locations noted when removing the existing display.
2. Refer to the Power Wheelchair Wiring Guide, part number 1167603 for more information
regarding securing the cable.
4.7 Program the MK6i Mini Color Display
Reading Programming Settings From the Basic Memory Card
1. Insert the memory card into the mini color display.
2. Turn the wheelchair On.
3. Use the up/down arrows to select READ FROM CARD.
4. Press the Select key.
Reading Programming Settings From the Professional Memory Card
1. Insert the memory card into the mini color display.
2. Turn the wheelchair On.
3. Use the up/down arrows to select MEMORY CARD.
4. Select SYSTEM.
5. Select READ.
Ensure the gaskets D are installed in the top connector cap and between
network connectors.
CAUTION
Risk of Damage To Cables
DO NOT overtighten the tie-wraps securing the cables. Overtightened tie-wraps
can damage cables.
To ensure proper use and operation of the mini color display, the cable must be
properly secured.
6. Select FOLDER.
7. Select the desired folder to read from.
8. Select NAME.
9. Select the desired system to read from.
10. Select START.
Programming Settings Without a Memory Card
Refer to the MK6i Field Reference Guide, part number 1141471, for programming information.
FIGURE 1 Installing the MK6i Mini Color Display
G
C
D
F
D
D
G
F
E
B
A
Invacare Corporation
www.invacare.com
USA
One Invacare Way
Elyria, Ohio USA
44036-2125
440-329-6000
800-333-6900
Technical Services
440-329-6593
800-832-4707
Canada
570 Matheson Blvd. E Unit 8
Mississauga Ontario
L4Z 4G4 Canada
800-668-5324
© 2011 Invacare Corporation. All rights reserved. Republication,
duplication or modification in whole or in part is prohibited without prior
written permission from Invacare. Trademarks are identified by ™ and ®.
All trademarks are owned by or licensed to Invacare Corporation or its
subsidiaries unless otherwise noted.
Part No 1171901 Rev A - 6/11
/