Hach sensION+ EC71 User manual

DOC022.97.90252

sensION

™

+ EC71

04/2011, Edition 1

User Manual

Manuel d'utilisation

Manual del usuario

Manual do usuário

用户手册

取扱説明書

사용 설명서

คูมือผูใช

English..................................................................................................................................................................................................3

Français.............................................................................................................................................................................................17

Español..............................................................................................................................................................................................32

Português..........................................................................................................................................................................................47

中文......................................................................................................................................................................................................62

日本語.................................................................................................................................................................................................76

한글......................................................................................................................................................................................................91

ไทย.......................................................................................................................................................................................................105

2

Specifications

Specifications are subject to change without notice.

Specification Details

Dimensions 35 x 20 x 11 cm (13.78 x 7.87 x 4.33 in.)

Weight 1100 g (2.43 lb)

Meter enclosure IP42

Power requirements

(external)

100–240 V, 0.4 A, 47-63 Hz

Meter protection class Class II

Storage temperature –15 to +65 °C (5 to +149 °F)

Operating temperature 0 to 40 °C (41 to 104 °F)

Operating humidity < 80% (non-condensing)

Measuring error (± 1 digit) Conductivity: ≤ 0.1%, Salinity/TDS: ≤ 0.5%,

temperature: ≤ 0.2 °C (0.36 °F)

Reproducibility (± 1 digit) Conductivity: ± 0.1%, Salinity/TDS: ± 0.1 %,

temperature: ± 0.1 °C (0.18 °F)

Data storage 330 results and last 9 calibrations

Connections Conductivity probe with built-in Pt1000 sensor:

telephonic connector; magnetic stirrer: RCA

connector

RS232C for printer or PC: telephonic connector;

external PC keyboard: mini DIN connector

Temperature correction Manual, Pt 1000 temperature probe (A.T.C.), NTC 10

kΩ probe

Measurement display lock Continuous measurement, by stability and by time

Display Liquid crystal, backlit, 128 x 64 dots

Keyboard PET with protective treatment

Certification CE

General information

Revised editions are found on the manufacturer’s website.

Safety information

Please read this entire manual before unpacking, setting up or operating

this

equipment. Pay attention to all danger and caution statements. Failure

to do so could result in serious injury to the operator or damage to the

equipment.

Make sure that the protection provided by this equipment is not impaired,

do not use or install this equipment in any manner other than that specified

in this manual.

Use of hazard information

D A N G E R

Indicates a potentially or imminently hazardous situation which, if not avoided, will

result in death or serious injury.

W A R N I N G

Indicates a potentially or imminently hazardous situation which, if not avoided,

could result in death or serious injury.

C A U T I O N

Indicates a potentially hazardous situation that may result in minor or moderate

injury.

N O T I C E

Indicates a situation which, if not avoided, may cause damage to the instrument.

Information that requires special emphasis.

Precautionary labels

Read all labels and tags attached to the instrument. Personal injury or

damage to the instrument could occur if not observed. A symbol, if noted

on the instrument, will be included with a danger or caution statement in

the manual.

English 3

This symbol, if noted on the instrument, references the instruction

manual for operation and/or safety information.

Electrical equipment marked with this symbol may not be disposed of

in European public disposal systems after 12 August of 2005. In

conformity with European local and national regulations (EU Directive

2002/98/EC),

European electrical equipment users must now return old

or end-of-life equipment to the Producer for disposal at no charge to

the user.

Note: For return for recycling, please contact the equipment producer or supplier

for instructions on how to return end-of-life equipment, producer-supplied electrical

accessories, and all auxillary items for proper disposal.

Product overview

The sensION

™

+ meters are used with probes to measure various

parameters in water.

The sensION

™

+ EC71 meter measures conductivity, salinity, TDS and

temperature.

Measurement data can be stored and transferred to a printer

or PC.

Product components

Refer to Figure 1 to make sure that all components have been received.

If any items are missing or damaged, contact the manufacturer or a sales

representative immediately.

Figure 1 Meter components

1 Standard solutions (147 µS/cm,

1413 µS/cm and 12.88 mS/cm)

5 Rod with o-ring

2 Calibration beakers (with magnetic

bar inside)

6 Probe (included with kits only)

3 Probe holder 7 Meter

4 Power supply

Installation

Assemble the probe holder

Follow the numbered steps to assemble the probe holder and to connect

the magnetic stirrer.

4 English

1 2

3 4

English 5

Connect to AC power

D A N G E R

Electrocution hazard. If this equipment is used outdoors or in potentially

wet locations, a Ground Fault Circuit Interrupt (GFCI/GFI) device must

be used to connect the equipment to its main power source.

The meter can be powered by AC power with the universal power adapter.

1. Select the correct adapter plug for the power outlet from the adapter

kit.

2. Connect the universal power adapter to the meter (Figure 2).

3. Connect the universal power adapter to an AC receptacle (Figure 3).

4. Turn the meter on.

Figure 2 Connector panel

1 Magnetic stirrer connector 4 PC keyboard, mini DIN connector

2 Conductivity probe connector 5 Power supply

3 RS-232 for printer or PC connector

Figure 3 AC power connection

6 English

User interface and navigation

User interface

Keypad description

1 RETURN key: cancel or exit the

current menu screen to the previous

menu screen

5 DOWN key: scroll to other options,

change a value

2 MEASUREMENT key: confirm the

selected option

6 ON/OFF:

turn on or turn off the meter

3 UP key: scroll to other options,

change a value

7 LEFT key: change the measuring

unit, enter numbers and letters

4 RIGHT key: change the measuring

unit, enter numbers and letters

Display description

The

meter display shows the concentration, units, temperature, calibration

status, operator ID, sample ID, date and time.

Figure 4 Single screen display

1 Sample ID 4 Sample temperature (ºC or ºF)

2 Measurement unit and value

(conductivity, salinity, TDS or

salinity)

5 Visual measurement timer

3 Measurement

mode or time and date

Navigation

Use the to return to the previous menu. Use the measure key to take

a sample measurement or to confirm options. Use the arrow keys

to scroll to other options or to change a value. To change the parameters

use the arrow keys

and . Refer to each task for specific instructions.

Start-up

Turn the meter on and off

N O T I C E

Make sure that the probe is connected to the meter before the meter is turned on.

Push to turn on or turn off the meter. If the meter does not turn on, make

sure

that the AC power supply is properly connected to an electrical outlet.

Change the language

The display language is selected when the meter is powered on for the

first time.

1. Use the

or to select a language from a list.

2. Confirm with . The measurement screen shows DATA OUTPUT.

English 7

3. Select

Deactivated if no printer or PC is connected and confirm. Refer

to Select the data output on page 10 for more information about Data

Output.

Standard operations

Calibration

W A R N I N G

Chemical exposure hazard. Obey laboratory safety procedures and wear all of the

the personal protective equipment appropriate to the chemicals that are handled.

Refer to the current material safety data sheets (MSDS) for safety protocols.

Calibration settings

The calibration settings contain Calibration type, Calibration frequency

and Display options.

1. From

the main menu use the

or to select CALIBRATION. Confirm.

2. Use the to enter the calibration menu.

3. Use the or to select the following options:

Option Description

Calibration

type

Calibration type—select Molar Standards, Demal

Standards, NaCl Standards, Calibration to a X value, data

introduction or Theoretical calibration. Refer to Calibration

types for more information.

Cal. frequency Calibration reminder—can be set between 0–99 days

(default

15 days). The display shows the remaining time to

the new calibration. Refer to Set the calibration reminder

on page 9 for more information.

Display Ω Display Resistivity—select YES to show simultaneously

conductivity and resistivity.

Calibration types

Different calibration types can be selected.

1. From

the main menu use the

or to select CALIBRATION. Confirm.

2. Use the to enter the calibration menu.

3. Use the or to select Calibration type.

Option Description

Molar Standards 147 µS/cm, 1413 µS/cm, 12.88 mS/cm and 111.8

mS/cm at 25 °C (77 °F)

Demal Standards 1049 µS/cm, 12.85 mS/cm and 111.31 mS/cm at 25

°C (77 °F)

NaCl Standards 1014.9 µS/cm 25 °C (77 °F)

Calibration to a X

value

To adjust manually any scale value of the measured

conductivity.

Data introduction Manual probe constant introduction.

Theoretical

calibration

The probe calibration data is replaced with C=1.000

cm

-1

.

Calibration procedure

This

procedure is for general use with liquid calibration solutions. Refer to

the documents that are included with each probe for additional information.

Note: Solutions should be stirred during calibration. For more information about the

stirring settings, refer to Change the stirring settings on page 10.

1. Pour the buffers or calibration solutions into the labeled calibration

beakers.

2. From the main menu use the

or and and to select the

CALIBRATION parameter. Confirm.

3. If required select the Operator ID (1 to 10) and confirm.

4. Rinse the probe with deionized water and put the probe into the first

calibration beaker. Be sure that there are no air bubbles in the probe

measuring chamber.

5. Push to Start calibration.

6. Push to measure the first calibration solution.

The next calibration solution is shown.

7. Rinse the probe with deionized water and put the probe into the first

calibration beaker. Be sure that there are no air bubbles in the probe

measuring chamber.

8. Push to measure the second calibration solution.

8 English

The next calibration solution is shown.

9. Rinse the probe with deionized water and put the probe into the first

calibration beaker. Be sure that there are no air bubbles in the probe

measuring chamber.

10. Push to measure the third calibration solution.

When

the calibration is good, the display briefly shows Calibration OK

and then returns to the main menu.

Note: When a printer is connected the print menu opens and the result can be

printed.

View the calibration data

Data from the most recent calibration can be shown.

1. From the main menu use the

or to select DATA LOGGER.

Confirm.

2. Select Display data.

3. Select Calibration data and confirm with . The last calibration data

is shown.

•

pH-the slope and offset values are shown alternating with the

deviation (in %) and calibration temperature.

• Conductivity-the cell constant and calibration temperature for each

standard are shown.

Set the calibration reminder

The calibration reminder can be set between 0 to 23 hours or 1-7 days

(default 0 days). The display shows the remaining time to the new

calibration.

Note: When 0 days is selected, the calibration reminder is turned off.

1. From the main menu use the

or to select CALIBRATION. Confirm.

2. Use the to enter the calibration menu.

3. Use the or to select Cal. frequency and confirm.

4. Use the and to advance to the next step and use the or to

change a value. Confirm.

Push to start the calibration.

Sample measurements

Each probe has specific preparation steps and procedures for taking

sample measurements.

1. From

the main menu use the

or and and to select MEASURE.

Confirm.

2. Use the to change the following settings. Confirm every entry.

Option Description

TC TC—select Linear or Natural waters. Linear: enter a value in %/

°C (default 2.00%/Temperature). Natural waters: Non-linear for

natural waters, according to EN27888

Tref Reference temperature—select between 20 or 25 °C or Other

temperature.

TDS Factor Total dissolved solids (TDS) factor—enter TDS Factor

Measure Stability—select By stability Criterion: ± 1 digit in 6 s. In

continuous—enter

the time interval for the In continuous Acquis.

interval. By time—enter the time interval for data storage or

printing data.

Display Ω Display Resistivity—select YES to show simultaneously

conductivity and resistivity.

3. Push

to start the measurement.

Note: If the measurement is not stabilizing after 120 seconds, the meter turns

automatically into the continuous measurement mode.

Advanced operations

Use a sample ID

The sample ID tag is used to associate readings with a particular sample

location. If assigned, stored data will include this ID.

1. From the main menu use the

or to select SYSTEM. Confirm.

2. Use the or to select Sample ID and confirm.

English 9

3. Use the or to select

Option Description

Automatic A consecutive number will be automatically assigned to every

sample.

Manual A keyboard or a barcode scanner is required to enter the sample

ID

name before taking a measurement (maximum 15 characters).

Select the data output

Data can be stored or transferred to a printer or to a PC.

1. From the main menu use the

or to select SYSTEM. Confirm.

2. Use the or to select Data Output and confirm.

3. Use the or to select

Option Description

Deactivated Select Deactivated if no printer or PC is connected.

For Printer Select Dot matrix printer or Thermal printer.

For Computer Select Terminal, ComLabo or ComLabo Easy. The ComLabo

Software controls several modules, pH and conductivity

meters, automatic burettes, Samplers and so on from a

computer. The ComLabo Easy software gets pH and

conductivity data from a PC.

Change the date and time

The date and time can be changed from the Date / Time menu.

1. From the main menu use the or to select SYSTEM. Confirm.

2. Use the or to select Date / Time and confirm.

3. Use the and to advance to the next step and use the or to

change a value. Confirm.

The current date and time will be shown on the display.

Adjust the display contrast

1. From the main menu use the or to select SYSTEM. Confirm.

2. Use the or to select Display contrast and confirm.

3. Use the and to adjust the contrast of the display and confirm.

Adjust the temperature

The temperature measurement can be adjusted at 25 °C (77 °F) and/or

85 °C (185 °F) to increase accuracy.

1. Put the probe and a reference thermometer in a container of water at

approximately 25 °C and allow the temperature to stabilize.

2. Compare

the temperature read by the meter with that of the reference

thermometer. The difference is the adjustment value for the meter.

Example: reference thermometer: 24.5 °C; meter: 24.3 °C. Adjustment

value: 0.2 °C.

3. Enter the adjustment value for the 25 °C reading:

a. From the main menu use the

or to select SYSTEM. Confirm.

b. Use the or to select Readjust temp. and confirm.

c. Use the or to select 25 °C and confirm.

d. Use the arrow keys to enter the adjustment value for 25 °C.

Confirm.

4. Put the probe and a reference thermometer in a container of water at

approximately 85 °C and allow the temperature to stabilize.

5. Compare the temperature from the meter with that of the reference

thermometer. The difference is the adjustment value for the meter.

a. Use the or to select 85 °C and confirm.

b. Use the arrow keys to enter the adjustment value for 85 °C.

Confirm.

c. Select Save changes and confirm.

Change the stirring settings

The magnetic stirrer can be turned on and the stirring speed can be

changed in the Stirring menu.

10 English

1. From the main menu use the or to select SYSTEM. Confirm.

2. Use the or to select Stirring and confirm.

3. To turn on/off the stirrer push .

4. When the stirrer is turned on, use the or to change the stirring

speed in %.

Note: Use

the

or to change the stirring speed during calibration and during

a measurement.

Change the temperature units

The temperature units can be changed to Celsius or Fahrenheit.

1. From the main menu use the or to select SYSTEM. Confirm.

2. Use the or to select Temperature units and confirm.

3. Use the or to select between Celsius or Fahrenheit and confirm.

Data logger

Display data

The Display data log contains Measurement data, Electrode report and

Calibration

data. The stored data can be send to a printer or to a PC. When

the data log becomes full (400 data points), the oldest data point is deleted

when a new data point is added.

1. From the main menu use the

or to select SYSTEM. Confirm.

2. Use the or to select DATA LOGGER and confirm.

3. Use the or to select Display data and confirm.

4. Use the or to select

Option Description

Measurement data Measurement data—stores automatically each time a

sample is measured

Electrode report Electrode report—stores automatically the electrode

history and measurement conditions

Calibration data Calibration data—stores automatically the current

calibration

Delete data

The entire measurement data or electrode report log can be deleted to

remove data that has already been sent to a printer or PC.

1. From the main menu use the or to select SYSTEM. Confirm.

2. Use the or to select DATA LOGGER and confirm.

3. Use the or to select Erase and confirm.

4. Use the or to select Measurement data or Electrode report and

confirm. Confirm again to delete the data.

The entire log is deleted at once.

Send data to a printer or to a computer

N O T I C E

The data output (printer or PC) needs to be selected first, so that the Print menu

is available (refer to Select the data output on page 10).

Note: Refer to Report output on page 11 to select the report output type.

1. From the main menu use the or to select SYSTEM. Confirm.

2. Use the or to select DATA LOGGER and confirm.

3. Use

the

or to select Print and confirm. Select one of the following

options and confirm with to print the data: Measurement data,

Electrode data, Calibration data, Calibration report or Instrument

condit.

Report output

N O T I C E

The data output (printer or PC) needs to be selected first, so that the Type of report

menu is available (refer to Select the data output on page 10).

Different report output types can be selected when a printer or a PC is

connected.

1. From the main menu use the or to select SYSTEM. Confirm.

2. Use the or to select Type of report and confirm.

English 11

3. When a printer or a computer and Terminal is connected, use the

or to select

Option Description

Reduced Select Several or One sample as an output format

Standard Select Several or One sample as an output format. Select several:

Users: The user name appears on the printed report (17

characters). Header:The company name can be added as a

header (40 characters) and appears on the print report. Identify

sensor:The sensor model and the sensor serial number can be

added and appears on the print report.

GLP Select Several or One sample as an output format. Select several:

Users: The user name appears on the printed report (17

characters). Header:The company name can be added as a

header (40 characters) and appears on the print report. Identify

sensor:The sensor model and the sensor serial number can be

added and appears on the print report.

4. When

a computer is connected and ComLabo Easy (refer to for more

information) is selected, use the

or to select

Option Description

Users The user name appears on the printed report (17

characters).

Identify sensor The sensor model and the sensor serial number can be

added and appears on the print report.

Maintenance

W A R N I N G

Multiple hazards. Do not disassemble the instrument for maintenance. If the

internal components must be cleaned or repaired, contact the manufacturer.

C A U T I O N

Personal injury hazard. Only qualified personnel should conduct the tasks

described in this section of the manual.

Clean the instrument

N O T I C E

Never use cleaning agents such as turpentine, acetone or similar products to clean

the instrument including the display and accessories.

Clean the exterior of the instrument with a moist cloth and a mild soap

solution.

Clean the probe

Clean the probe as needed. Refer to Troubleshooting on page 14 for

more information about cleaning. Refer to the probe documentation for

information about the probe maintenance.

Use the cleaning agents listed in Table 1 for contaminations on the

conductivity probe.

Table 1 Cleaning agents for the conductivity probe

Contamination Cleaning agent

Grease, oils, fats Electrode cleaning solution

Limescale 0.1 N HCl solution

Replace the magnetic stirrer

If

the magnetic stirrer does not start, follow the numbered steps to replace

the magnetic stirrer.

12 English

1 2

English 13

Troubleshooting

Refer

to the following table for common problem messages or symptoms,

possible causes and corrective actions.

Table 2 Calibration warnings and errors

Error/Warning Solution

UNSTABLE READING

Time t> 100 s

Calibrate again.

Examine

the probe: Make sure that the probe is properly

immersed in the sample; make sure that there are no air

bubbles inside the probe measuring chamber; rinse the

probe with ethanol.

Check temperature.

Check the cell.

Make sure the standard temperature is constant during

the calibration.

Examine the probe: Make sure that the probe is properly

immersed in the sample; make sure that there are no air

bubbles inside the probe measuring chamber; rinse the

probe with ethanol.

STANDARD

TEMPERATURE

< 15 °C or > 35 °C

Calibrate again.

The standard temperature must be between 15 and 35

ºC.

Difference C > 30 % Calibrate again.

Examine the probe: Make sure that the probe is properly

immersed in the sample; make sure that there are no air

bubbles inside the probe measuring chamber; rinse the

probe with ethanol; connect a different probe to verify if

problem is with probe or meter.

Examine the standard solution: Use new standard

solution.

C < 0.05 or > C > 50.00

°C

SAME BUFFERS

Buffer or cell in poor

conditions

BUFFER NOT

RECOGNIZED

Difference C > 30 %

SAME STANDARDS

Table 3 Measurement warnings and errors

Error/Warning Solution

23.2 °C

728 µS/cm @ 25 °C

Calibrate again.

EC out of range Examine the probe: Make sure that the probe is properly

immersed

in the sample; make sure that there are no air

bubbles inside the probe measuring chamber; rinse the

probe with ethanol; connect a different probe to verify if

problem is with probe or meter.

Out of range °C Examine the temperature sensor.

Connect a different probe to verify if problem is with

probe or meter.

TC = 0

Impossible to measure

salinity

Modify TC

Time > 150 s Examine the temperature.

Examine the probe: Make sure that the probe is properly

immersed in the sample; make sure that there are no air

bubbles inside the probe measuring chamber; rinse the

probe with ethanol; connect a different probe to verify if

problem is with probe or meter.

Replacement parts and accessories

Note: Product and Article numbers may vary for some selling regions. Contact the

appropriate distributor or refer to the company website for contact information.

Replacement parts

Description Item no.

sensION+ PH3 Lab pH-meter with accessories, without

probe

LPV2000.97.0002

sensION+ PH31 Lab pH-meter, GLP, with accessories,

without probe

LPV2100.97.0002

14 English

Replacement parts and accessories (continued)

Description Item no.

sensION+ MM340 Lab pH & Ion-meter, GLP, 2 channels,

with accessories, without probe

LPV2200.97.0002

sensION+ EC7 Lab conductivity meter, with accessories,

without probe

LPV3010.97.0002

sensION+ EC71 Lab conductivity meter, GLP, with

accessories, without probe

LPV3110.97.0002

sensION+ MM374, 2 channel Lab meter, GLP, accessories,

without probes

LPV4110.97.0002

Consumables

Description Item no.

Conductivity standard solution 147 µS/cm, with certificate, 125

mL

LZW9701.99

Conductivity standard solution 1413 µS/cm, with certificate, 125

mL

LZW9711.99

Conductivity standard 12.88 mS/cm, with certificate, 125 mL LZW9721.99

Conductivity standard 147 µS/cm, with certificate, 250 mL LZW9700.99

Conductivity standard 1413 µS/cm, with certificate, 250 mL LZW9710.99

Conductivity standard 12.88 mS/cm, with certificate, 250 mL LZW9720.99

Enzyme solution 2964349

Pepsin Cleaning Solution 2964349

Electrode cleaning solution 2965249

0.1 N HCl solution 1481253

Ethanol, 95% (Grease, oils, fats) 2378900

Accessories

Description Item no.

Thermal printer, RS232, for sensION+ benchtop LZW8201.99

Thermal paper for printer LZW8201, bag with 5 rolls LZW9117.99

Dot-impact printer, RS232, for sensION+ instruments LZW8200.99

Standard paper for printer LZW8200, bag with 10 rolls LZW9000.99

Ribbon for printer LZW8200, 3 units LZW9001.99

LabCom Easy PC SW, for sensION+ GLP, CD, cable, USB

adapter

LZW8997.99

LabCom PC SW, for sensION+ GLP, CD, cable, USB adapter LZW8999.99

RS232 cable, for sensION+ benchtop instruments LZW9135.99

RS232 cable for sensION+ benchtop, with USB adapter LZW9135USB.99

Magnetic stirrer with sensor holder, for sensION+ MM

benchtop

LZW9319.99

3x50 mL printed beaker for benchtop conductivity calibration LZW9111.99

Three-sensor holder, for sensION+ benchtop instruments LZW9321.99

Holder and clamp for three sensors LZW9155.99

Pyrex glass chamber, continuous flow measurements LZW9118.99

PP protector, electrode storage LZW9161.99

Standard solutions

Conductivity standard solutions

Refer to Table 4 for conductivity values of standard solutions at varying

temperatures.

English 15

Table 4 Conductivity and temperature values

Temperature Conductivity (EC)

°C °F µS/cm µS/cm mS/cm mS/cm

15.0 59 119 1147 10.48 92.5

16.0 60.8 122 1173 10.72 94.4

17.0 62.6 125 1199 10.95 96.3

18.0 64.4 127 1225 11.19 98.2

19.0 66.2 130 1251 11.43 100.1

20.0 68 133 1278 11.67 102.1

21.0 69.8 136 1305 11.91 104.0

22.0 71.6 139 1332 12.15 105.4

23.0 73.4 142 1359 12.39 107.9

24.0 75.2 145 1386 12.64 109.8

25.0 77 147 1413 12.88 111.8

26.0 78.8 150 1440 13.13 113.8

27.0 80.6 153 1467 13.37 115.7

28.0 82.4 156 1494 13.62 —

29.0 84.2 159 1522 13.87 —

30.0 86 162 1549 14.12 —

31.0 87.8 165 1581 14.37 —

32.0 89.6 168 1609 14.62 —

33.0 91.4 171 1638 14.88 —

34.0 93.2 174 1667 15.13 —

35.0 95 177 1696 15.39 —

16 English

Caractéristiques techniques

Les caractéristiques techniques peuvent être modifiées sans préavis.

Caractéristiques Détails

Dimensions 35 x 20 x 11 cm (13,78 x 7,87 x 4,33 po)

Poids 1 100 g (2,43 lb)

Boîtier de l'appareil IP42

Alimentation (externe) 100–240 V, 0,4 A, 47-63 Hz

Classe de protection de

l'instrument

Classe II

Température de stockage –15 à +65 °C (5 à +149 °F)

Température de

fonctionnement

0 à 40 °C (41 à 104 °F)

Humidité de fonctionnement < 80% (sans condensation)

Erreur de mesure (± 1 chiffre) Conductivité : ≤ 0,1 %, salinité/TDS : ≤ 0,5 %,

température : ≤ 0,2 °C (0,36 °F)

Reproductibilité (± 1 chiffre) Conductivité : ± 0,1 %, salinité/TDS : ± 0,1 %,

température : ± 0,1 °C (0,18 °F)

Stockage des données 330 résultats et 9 derniers étalonnages

Connexions Sonde de conductivité avec capteur Pt 1000

intégré : connecteur téléphonique ; agitateur

magnétique : connecteur RCA

RS232C pour imprimante ou PC : connecteur

téléphonique ; clavier PC externe : connecteur

mini-DIN

Correction de température Manuelle, sonde de température Pt 1000

(A.T.C.), sonde NTC 10 kΩ

Verrouillage d'affichage de

mesure

Mesure continue, par stabilité et par durée

Afficheur Cristal liquide, rétroéclairé, 128 x 64 points

Caractéristiques Détails

Clavier PET avec traitement de protection

Certification CE

Généralités

Les éditions révisées se trouvent sur le site Internet du fabricant.

Consignes de sécurité

Veuillez

lire l'ensemble du manuel avant le déballage, la configuration ou

la mise en fonctionnement de cet appareil. Respectez toutes les

déclarations de prudence et d'attention. Le non-respect de cette

procédure peut conduire à des blessures graves de l'opérateur ou à des

dégâts sur le matériel.

Assurez-vous que la protection fournie avec cet appareil ne soit pas

compromise, n'utilisez pas ou n'installez pas cet appareil d'une autre façon

que celle décrite dans ce manuel.

Interprétation des indications de risques

D A N G E R

Indique une situation de danger potentiel ou imminent qui, si elle n'est pas évitée,

entraîne des blessures graves, voire mortelles.

A V E R T I S S E M E N T

Indique une situation de danger potentiel ou imminent qui, si elle n'est pas évitée,

peut entraîner des blessures graves, voire mortelles.

A T T E N T I O N

Indique une situation de danger potentiel qui peut entraîner des blessures

mineures ou légères.

A V I S

Indique une situation qui, si elle n'est pas évitée, peut occasionner

l'endommagement du matériel. Informations nécessitant une mise en avant

particulière.

Français 17

Etiquettes de mise en garde

Lire

toutes les informations et toutes les étiquettes apposées sur l’appareil.

Des personnes peuvent se blesser et le matériel peut être endommagé si

ces instructions ne sont pas respectées. Si un symbole ‘danger’ ou

‘attention’ se trouve sur l’instrument, une explication est indiquée dans le

manuel.

Lorsque ce symbole est présent sur l’instrument, reportez-vous au

manuel d’instructions pour obtenir des informations relatives au

fonctionnement et/ou à la sécurité.

L’équipement électrique portant ce symbole ne peut être mis au rebut

dans

les systèmes de mise au rebut publics européens après le 12 août

2005. Conformément aux règlements nationaux et européens

(Directive 2002/98/EC), les appareils électriques doivent, depuis le 12

août 2005, ne pas être mis au rebut dans les décharges traditionnelles,

mais être, à la fin de leur service, renvoyés par les utilisateurs

européens au fabricant, qui se chargera de les éliminer à ses frais.

Remarque : Pour le retour à des fins de recyclage, veuillez contactez le fabricant

ou le fournisseur d'équipement pour obtenir les instructions sur la façon de

renvoyer l'équipement usé, les accessoires électriques fournis par le fabricant, et

tous les articles auxiliaires pour mise au rebut appropriée.

Présentation du produit

Les appareils de mesure de la série ION

™

+ s'utilisent avec des sondes

pour mesurer différents paramètres dans l'eau.

L'appareil

de mesure sensION

™

+ EC71 mesure la conductivité, la salinité,

le TDS et la température. Les données de mesure peuvent être

enregistrées et transférées vers une imprimante ou un PC.

Composants du produit

Consultez la Figure 1 pour vous assurer que tous les éléments ont bien

été reçus. Si des éléments manquent ou sont endommagés, contactez

immédiatement le fabricant ou un représentant commercial.

Figure 1 Composants de l'appareil

1 Solutions

étalons (147 µS/cm, 1 413

µS/cm et 12,88 mS/cm)

5 Tige avec joint torique

2 Béchers d'étalonnage (avec barre

magnétique)

6 Sonde (comprise uniquement dans

les kits)

3 Support de sonde 7 Appareil de mesure

4 Alimentation

Installation

Monter le support de sonde

Suivez les étapes numérotées afin de monter le support de sonde et de

brancher l'agitateur magnétique.

18 Français

1 2

3 4

Français 19

Branchement sur alimentation CA

D A N G E R

Risque d'électrocution Si cet équipement est utilisé à l'extérieur ou dans

des lieux potentiellement humides, un disjoncteur de fuite à la terre

(GFCI/GFI) doit être utilisé pour le branchement de l'équipement à sa

source d'alimentation secteur.

L'appareil de mesure peut être alimenté sur secteur à l'aide d'un

adaptateur d'alimentation universel.

1. Sélectionnez

la fiche d'adaptateur appropriée à la prise électrique dans

le kit adaptateur.

2. Branchez l'adaptateur d'alimentation universel à l'appareil (Figure 2).

3. Branchez l'adaptateur d'alimentation universel à une prise CA

(Figure 3).

4. Allumez l'appareil.

Figure 2 Panneau des connecteurs

1 Connecteur de l'agitateur

magnétique

4 Clavier PC, connecteur mini-DIN

2 Connecteur de la sonde de

conductivité

5 Alimentation

3 Connecteur RS-232 pour

imprimante ou PC

Figure 3 Branchement sur alimentation CA

20 Français

Page is loading ...

Hach sensION+ EC71 User manual

Hach sensION+ EC71 User manual

in other languages

Related papers

Other documents