Star Trac Multi Five-Station M9605 Installation guide

Assembly & Setup

STAR TRAC FITNESS 1 of 23 635-4173 Rev: A

INSPIRATION STRENGTH

Multi Station (5 Station)

SKU 9IP-M9605

INSTALLATION INSTRUCTIONS

Assembly & Setup

STAR TRAC FITNESS 2 of 23 635-4173 Rev: A

Required Tools

• Size 13 and 17 metric open end wrench

• Size 5 and 6 metric Allen wrench

• Step stool or ladder

• Pallet jack

Getting started

1. Put the main pod where you want it permanently

(Figure on right) first then the weight stacks will follow

each unit.

Fig. 1

Assembly & Setup

STAR TRAC FITNESS 3 of 23 635-4173 Rev: A

2. Remove from pallet by tilting it to one side.

3. Make sure to clear out trash and boxes as you go

along

Note: Remember, 124 inches will be needed between

towers. Make sure the crossover station facing the

correct way before starting to stack the weights.

There are no orders in which unit to build.

Fig. 2

Assembly & Setup

STAR TRAC FITNESS 4 of 23 635-4173 Rev: A

Station Assembly

1. Contents: Box will come with what is shown on Fig. 3.

The additional 4 boxes will have the weights

Assembly & Setup

STAR TRAC FITNESS 5 of 23 635-4173 Rev: A

Fig. 3

2. Make sure the set collar set screws are facing out.

3. Put caps back on then tighten by holding guide rod

with upwards with one hand and the other hand

screwing.

Fig. 4

4. Before putting in the weights to the guide rods, lift the

frame to place the cable pulley and rubber feet under

the unit.

Fig. 5

Assembly & Setup

STAR TRAC FITNESS 6 of 23 635-4173 Rev: A

5. Insert washers on the screws

6. Tighten all four screws to the frame

Fig. 6

7. Start with box 5 of 5 first (which is the heaviest plate)

8. Figure shows the weight stack range.

Fig. 7

Assembly & Setup

STAR TRAC FITNESS 7 of 23 635-4173 Rev: A

9. Insert the heavy weight first.

10. Check to see if the weight switches flip back and forth

as you insert them.

Fig. 8

11. Screw upper pulley bracket assembly to the frame with

three (3) screws and washers

Fig. 9

Assembly & Setup

STAR TRAC FITNESS 8 of 23 635-4173 Rev: A

12. Screw on plate with two (2) screws and washers.

13. Make sure the cable is not going through the whole of

the plate. Should be going through hole of the upper

pulley assembly

Fig. 10

14. Locate the peg by the lower pulley then unscrew it out.

Fig. 11

Assembly & Setup

STAR TRAC FITNESS 9 of 23 635-4173 Rev: A

15. Insert handle weld adjustment guide tube to the peg

and hand tight screws.

Note: Tighten with an Allen wrench after the upper

portion has been tightened

Fig. 12

Fig. 13

16. Remove the upper pulley to have access to perform the

next step.

Fig. 14

Assembly & Setup

STAR TRAC FITNESS 10 of 23 635-4173 Rev: A

17. After the bottom portion beam has been hand

tightened, line up the upper portion with the frame and

tighten with Allen wrench.

18. Do the same for the lower portion

Fig. 15

19. Place pulley back to frame. Make sure the cable is

going over the pulley then tighten.

Fig. 16

Assembly & Setup

STAR TRAC FITNESS 11 of 23 635-4173 Rev: A

20. Note #1 on the diagram shows the start of the cable

routing.

21. To begin; insert the cable by removing the upper pulley

(arrow #1) and insert between two staggered pulleys on

the red handle assembly.

22. Re-insert the pulley and follow the yellow routing

arrows.

23. #2 is another pulley that needs to be removed to insert

the cable to pass through.

Fig. 17

Assembly & Setup

STAR TRAC FITNESS 12 of 23 635-4173 Rev: A

24. After routing, take the tail end with the fasteners and

take off the fasteners

Fig. 18

25. As arrows show, the top nut is to tighten the cable.

Make sure not to have more than 3 threads showing.

26. Use pliers and wrench to tighten the fastener on the

lower arrow.

Fig. 19

Assembly & Setup

STAR TRAC FITNESS 13 of 23 635-4173 Rev: A

27. Placards always go on user’s right side

Fig. 20

Assembly & Setup

STAR TRAC FITNESS 14 of 23 635-4173 Rev: A

28. Ballet bars go on the mid section

Note: every screw needs to have washers on each end.

Fig. 21

29. Insert a washer on the screw and mount ballet bar to

frame

Fig. 22

30. Place plate to frame with holes lined up.

31. Insert the screw with a washer

32. Insert the washer and nut

Fig. 23

Assembly & Setup

STAR TRAC FITNESS 15 of 23 635-4173 Rev: A

TRICEPS

1. highest holes are for the triceps machine everything

has washers

Fig. 24

Assembly & Setup

STAR TRAC FITNESS 16 of 23 635-4173 Rev: A

2. Parts of the triceps machine are shown on Fig. 25.

Note: The additional 4 boxes will have the weights and

the figure shows the range.

Fig. 25

3. Place the pad to align with the holes. Screw them to the

frame with washers on both sides.

Fig. 26

Assembly & Setup

STAR TRAC FITNESS 17 of 23 635-4173 Rev: A

4. Insert cable through the hole above the plate rods

before installing the pulley bracket assembly.

Fig. 27

Assembly & Setup

STAR TRAC FITNESS 18 of 23 635-4173 Rev: A

5. Repeat the same procedure above on installing the

pulley bracket assembly and inserting the weights.

Note: To complete the installation on this section,

repeat steps from 1 to 16 on Station Assembly.

Fig. 28

Fig. 29

Assembly & Setup

STAR TRAC FITNESS 19 of 23 635-4173 Rev: A

6. Screw on the cables to the weight stack top plate.

Fig. 30

Assembly & Setup

STAR TRAC FITNESS 20 of 23 635-4173 Rev: A

Low Row

1. Parts of the triceps machine are shown on Fig. 34.

Note: The additional 4 boxes will have the weights.

Fig. 31

Page is loading ...

Star Trac Multi Five-Station M9605 Installation guide

Star Trac Multi Five-Station M9605 Installation guide

Related papers

Other documents