Contec GW1-ETH-WQ-US Owner's manual

Wireless I/O

Gateway Series

Ethernet to Sub-GHz Wireless

EU model

GW1-ETH-WQ-EU

USA model

GW1-ETH-WQ-US

User’s Manual

CONTEC CO., LTD.

GW1-ETH-WQ-EU, GW1-ETH-WQ-US

i

Check Your Package

Thank you for purchasing the CONTEC product.

The product consists of the items listed below.

Check, with the following list, that your package is complete. If you discover damaged or missing

items, contact your retailer.

Product Configuration List

- Product [GW1-ETH-WQ-EU or GW1-ETH-WQ-US] …1

- Setup Guide…1

- Warranty Certificate…1

- Serial Number Label…1

- Power Connector…1

- Antenna…1

GW1-ETH-WQ-EU

Antenna

Product Setup Guide Warranty Certificate

Serial Number Label

Power Connec

tor

ii

GW1-ETH-WQ-EU, GW1-ETH-WQ-US

GW1-ETH-WQ-US

Copyright

No part of this document may be copied or reproduced in any form by any means without prior written

consent of CONTEC CO., LTD.

CONTEC CO., LTD. makes no commitment to update or keep current the information contained in this

document. The information in this document is subject to change without notice.

All relevant issues have been considered in the preparation of this document. Should you notice an

omission or any questionable item in this document, please feel free to notify CONTEC CO., LTD.

Regardless of the foregoing statement, CONTEC assumes no responsibility for any errors that may

appear in this document or for results obtained by the user as a result of using this product.

Trademarks

Company and product names that are referred to in this manual are generally trademarks or registered

trademarks of their respective holders.

Antenna

Product Setup Guide Warranty Certificate

Serial Number Label

Power Connector

GW1-ETH-WQ-EU, GW1-ETH-WQ-US

iii

Table of Contents

Check Your Package .................................................................................................................................... i

Copyright ..................................................................................................................................................... ii

Trademarks .................................................................................................................................................. ii

Table of Contents ....................................................................................................................................... iii

1. Before Using the Product 1

About the Product........................................................................................................................................ 1

Features ................................................................................................................................................. 1

Support Software.................................................................................................................................. 2

List of Optional Products .................................................................................................................... 2

Customer Support ........................................................................................................................................ 3

Web Site................................................................................................................................................ 3

How to Obtain Service ................................................................................................................................ 3

Liability ........................................................................................................................................................ 3

Safety Precautions ....................................................................................................................................... 4

Safety Information ............................................................................................................................... 4

Handling Precautions ........................................................................................................................... 4

About listed transfer rate ..................................................................................................................... 7

Usage limitation ................................................................................................................................... 7

Environment ......................................................................................................................................... 7

Inspection.............................................................................................................................................. 7

Storage .................................................................................................................................................. 8

Disposal ................................................................................................................................................ 8

2. Setup 9

What is Setup? ............................................................................................................................................. 9

Step 1 Installing the Software .................................................................................................................. 10

Step 2 Setting the Hardware ..................................................................................................................... 11

Product Nomenclature ....................................................................................................................... 11

Name and Function ............................................................................................................................ 12

Step 3 Installing the Hardware ................................................................................................................. 16

Step 3 Installing the Hardware ................................................................................................................. 17

Step 4 Initializing the Software ................................................................................................................ 17

Setup Troubleshooting .............................................................................................................................. 18

Symptoms and Actions ...................................................................................................................... 18

When the Product Will Not Start Even After Trying the Above Actions ..................................... 19

When the problem is not solved ....................................................................................................... 19

3. Connecting and Installing 21

iv

GW1-ETH-WQ-EU, GW1-ETH-WQ-US

Connecting an antenna .............................................................................................................................. 21

Connecting the external power ................................................................................................................ 22

Connecting to your PC.............................................................................................................................. 24

Installation Conditions .............................................................................................................................. 25

Installation in a Network .......................................................................................................................... 27

Features of the Wireless Network .................................................................................................... 27

Operating Environment and Radio Waves ...................................................................................... 28

Constructing a Network .................................................................................................................... 29

4. About Software 33

About Windows Software ........................................................................................................................ 33

How to find a Help File ..................................................................................................................... 33

5. Function Description 35

Mesh ........................................................................................................................................................... 35

6. About Hardware 37

Hardware specification ............................................................................................................................. 37

Physical Dimensions ................................................................................................................................. 39

Antenna Directivity ................................................................................................................................... 40

GW1-ETH-WQ-EU ........................................................................................................................... 40

H-Plane (868MHz) ............................................................................................................................ 40

E-Plane (868MHz) ............................................................................................................................. 40

GW1-ETH-WQ-US ........................................................................................................................... 41

H-Plane (925MHz) ............................................................................................................................ 41

E-Plane (925MHz) ............................................................................................................................. 41

7. Appendix 43

Modbus TCP Slave specification ..................................................................................................... 43

Function Code .................................................................................................................................... 43

Register Address ................................................................................................................................ 43

Available Terminal (Slave) ............................................................................................................... 46

1. Before Using the Product

GW1-ETH-WQ-EU, GW1-ETH-WQ-US

1

1.

Before Using the Product

About the Product

This product is an Ethernet gateway that converts Ethernet into wireless in the Sub-GHz band*1.

Data from the Wireless I/O series terminal (Slave) can be sent to a PC via Ethernet, or received data

from PC can be sent via Ethernet.

With strength against obstacles, the long-distance communications enabled by wireless Sub-GHz band,

and multi-hop support, it is suitable to control or monitor devices that are spread in the wide area.

By using a driver library appropriate to the setting terminal, applications can be created with API

functions that support programming languages.

This product also supports Modbus TCP Slave, which makes it possible to control devices and collect

data from the higher communication devices containing Modbus Master function.

* This product should always be used along with the Wireless I/O series terminal (Slave).

* Driver library can be downloaded from the CONTEC website.

* The GW1-ETH-WQ-US can be used in the United States. The GW1-ETH-WQ-EU can be used in

European countries.

*Refer to

“Chapter 7. Appendix“

for Modbus TCP Slave specification.

*1 Sub-GHz indicates frequency bands of 1GHz and below. Available frequency band of the product

depends on the model. The GW1-ETH-WQ- EU can be used in the 863 - 870MHz band (Europe),

and the GW1-ETH-WQ-US can be used in the 902 - 928MHz band (The United States).

Features

- Supports Sub-GHz band wireless with excellent transmission distance

This product converts Ethernet (wired LAN) communication into Sub-GHz.

The Sub-GHz, with the good wraparound characteristics of radio waves, the transmission distance

(about 1 km) can be extended even there are obstacles. Stable communication can be achieved even in

the environment where radio waves are mixed. As the product is suitable for long distance

communication, network can be constructed on the wide area in the facilities without cable wiring.

- Highly reliable mesh communication

With wireless mesh technology, the communication continues by changing the routes automatically

even when disconnection occurs, for example. Communication stability enables the wireless network to

be strong against obstacles

- Modbus TCP Slave support

Modbus is a communication protocol widely adopted in the industrial field. It is possible to control

devices and collect data from the higher communication devices containing Modbus Master function.

1. Before Using the Product

2

GW1-ETH-WQ-EU, GW1-ETH-WQ-US

- Adaptable to a wide range of temperature

This product is capable of operating in the temperature between -20 and + 60°C. It can be installed in

the various environments.

- Compact design

Compact design, 62.0(W) x 64.0(D) x 24.0(H)mm features flexibility in installation.

- Easy mounting on DIN rail

This product can be mounted on DIN rail with an optional fixing bracket.

- Capable of adapting a wide-range power

This product is capable of dealing with a wide range of power in the differing environments.

- Work with various systems

Set the appropriate terminal (slave) with the product to work with the various systems.

Support Software

You should use CONTEC support software according to your purpose and development environment.

Windows version of driver library

API-PAC(W32)

Driver software with Win32API function (DLL) to support the function is ready to use per terminal.

The driver software contains sample programs such as VisualBasic and VisualC++, and the diagnosis

program to check the software operation.

For more details on the supported OS, applicable language and new information, please visit the

CONTEC’s Web site.

List of Optional Products

POA201-10-2 : AC-DC Power Adaptor (12VDC, 1A) *1

BRK-WQ-Y : Bracket for Wireless I/O Products

*1

The adaptor can be used in the temperature range between 0 and + 40°C

.

The support voltage of AC cable is 125 VAC 7 A.

*

Visit CONTEC website regarding information on the optional products.

1. Before Using the Product

GW1-ETH-WQ-EU, GW1-ETH-WQ-US

3

Customer Support

CONTEC provides the following support services for you to use CONTEC products more efficiently

and comfortably.

Web Site

https://www.contec.com/

Latest product information

CONTEC provides up-to-date information on products.

CONTEC also provides product manuals and various technical documents in the PDF.

Free download

You can download updated driver software and differential files as well as sample programs available in

several languages.

Note! For product information

Contact your retailer if you have any technical question about a CONTEC product or need its price,

delivery time, or estimate information.

How to Obtain Service

For replacement or repair, return the device freight prepaid, with a copy of the original invoice. Please

obtain a Return Merchandise Authorization number (RMA) from the CONTEC group office where you

purchased before returning any product.

* No product will be accepted by CONTEC group without the RMA number.

Liability

The obligation of the warrantor is solely to repair or replace the product. In no event will the

warrantor be liable for any incidental or consequential damages due to such defect or consequences that

arise from inexperienced usage, misuse, or malfunction of this device.

1. Before Using the Product

4

GW1-ETH-WQ-EU, GW1-ETH-WQ-US

Safety Precautions

Understand the following definitions and precautions to use the product safely.

Safety Information

This document provides safety information using the following symbols to prevent accidents resulting

in injury or death and the destruction of equipment and resources. Understand the meanings of these

labels to operate the equipment safely.

DANGER indicates an imminently hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING indicates a potentially hazardous situation which, if not avoided, could

result in death or serious injury.

CAUTION indicates a potentially hazardous situation which, if not avoided, may

result in minor or moderate injury or in property damage.

Handling Precautions

Do not use the product where it is exposed to flammable or corrosive gas. Doing so may result in

an explosion, fire, electric shock, or failure.

-

This product contains precision electronic elements and must not be used in locations subject to

physical shock or strong vibration. Otherwise, the product may malfunction, overheat, or cause a

failure.

-

Do not use or store this product in high temperature or low temperature surroundings, or do not expose

it to extreme temperature changes. Otherwise, the product may malfunction, overheat, or cause a

failure.

-

Do not use or store this device where it is exposed to direct sunlight or near stoves or other sources of

heat. Otherwise, the product may malfunction, overheat, or cause a failure.

-

Do not use the product in the vicinity of devices that generate strong magnetic force or noise.

Otherwise, the product may malfunction, overheat, or cause a failure.

-

Do not turn on the power without first connecting the antenna. Otherwise, the product may

malfunction, overheat, or cause a failure. Before turning the power on, be sure to check whether the

antenna is securely connected.

-

The specifications of the product are subject to change without notice for enhancement and quality

improvement. Even when using the product continuously, be sure to read the manual in the

CONTEC's website and understand the contents. Do not modify the product. CONTEC will bear no

responsibility for any problems, etc., resulting from modifying the product.

DANGER

WARNING

CAUTION

DANGER

CAUTION

1. Before Using the Product

GW1-ETH-WQ-EU, GW1-ETH-WQ-US

5

-

Do not modify the product. CONTEC will bear no responsibility for any problems, etc., resulting from

modifying the product.

-

The product must always be associated with the instruction manual.

-

When the product is used in a place that is affected by overcurrent or overvoltage (lightning surge),

select appropriate surge protection device for all of the route (Power line, earth, etc.). Consult with

the specialist regarding selecting, purchasing, and setting the surge protection device.

-

Bringing this product too close to a metal/concrete wall (including steel frames) may cause the

communication quality to deteriorate.

-

If a wireless device that uses the same channel (wireless frequency) as this product exists in the area

where communication is possible, a drop in the transmission speed or communication quality may

occur in certain situations, which may make it impossible to perform normal communication.

-

Modifications to the built-in wireless equipment are prohibited by law.

-

In some medical institutions and laboratories, radio-sensitive precision instruments are used and it may

be prohibited to use radio equipment.

- The use of antennas other than that included with the product is prohibited by law.

- The radio waves used by this product pass through obstacles (such as walls) and reach all locations

within a given area. If the security settings are not configured, communication may be intercepted by a

third party.

- This product is equipped with a security function, so be sure to configure the security settings prior to

use in order to reduce security problems.

- This product may not perform normal wireless communication due to factors such as the installation

environment, the setup, and the communication load of the network.

- Perform a verification in advance in an environment that matches your usage application to check that

there are no problems.

- For the introduction and installation of this product, hire a system integrator or other specialist who is

well-versed in the construction of network systems.

- When you are switching to this product from another model, it may be necessary to reconstruct the

network system due to differences in areas such as the product specifications and functions.

- When disposing of the product, follow the disposal procedures stipulated under the relevant laws and

municipal ordinances.

- Regardless of the foregoing statements, CONTEC is not liable for any damages whatsoever (Including

damages for loss of business profits) arising out of the use or inability to use this CONTEC product or

the information contained herein.

1. Before Using the Product

6

GW1-ETH-WQ-EU, GW1-ETH-WQ-US

FCC PART15

FCC PART15 Subpart B

FCC PART15 Subpart C

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions: (1) This device may not cause harmful interference,

and (2) this device must accept any interference received, including interference that may cause

undesired operation.

FCC CAUTION

Changes or modifications not expressly approved by the party responsible for compliance could void

the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and

used in accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at his own expense.

NOTE

This transmitter must not be co-located or operated in conjunction with any other antenna or

transmitter.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment

and meets the FCC radio frequency (RF) Exposure Guidelines. This equipment should be installed

and operated keeping the radiator at least 20cm or more away from person’s body.

1. Before Using the Product

GW1-ETH-WQ-EU, GW1-ETH-WQ-US

7

About listed transfer rate

Data transfer speed listed in this guide or Utility is a theoretical maximum value and does not indicate

the actual data speed.

Usage limitation

This product has not been developed or manufactured to be used in systems including the equipment

which is directly related to human lives *1 or the equipment which involves human safety and may

significantly affect the maintenance of public functions *2. Therefore, do not use the product for such

purposes.

*1 Medical devices such as life-support equipment and devices used in an operating theater.

*2 Main control systems at nuclear power stations, safety maintenance systems at nuclear facilities, other

important safety-related systems, operation control systems within group transport systems, air-traffic

control systems, etc.

Environment

Use this product in the following environment. If used in an unauthorized environment, the product

may overheat, malfunction, or cause a failure.

Operating temperature

-20 - 60°C

Humidity

10 - 90%RH (No condensation)

Corrosive gases

None

Floating dust particles

Not to be excessive

Inspection

Inspect the product periodically as follows to use it safely.

Gateway

- Check that the connector

has no dust or foreign

matter adhering.

1. Before Using the Product

8

GW1-ETH-WQ-EU, GW1-ETH-WQ-US

Storage

When storing this product, keep it in its original packing form.

(1) Put the product in the storage bag.

(2) Wrap it in the packing material, and then put it in the box.

(3) Store the package at room temperature at a place free from direct sunlight, moisture, shock,

vibration, magnetism, and static electricity.

Disposal

When disposing of the product, follow the disposal procedures stipulated under the relevant laws and

municipal ordinances.

2. Setup

GW1-ETH-WQ-EU, GW1-ETH-WQ-US

9

2.

Setup

What is Setup?

Setup means a series of steps to take before the product can be used.

Different steps are required for software and hardware.

The setup procedure varies with the OS and software used.

Use the CONTEC driver library in the Windows environment

This section describes the setup procedure to be performed before you can start developing application

programs for the board using the bundled disk “Driver Library API-PAC(W32)”.

Taking the following steps sets up the software and hardware. You can use the diagnosis program later

to check whether the software and hardware function normally.

Step 1 Installing the Software

Step 2 Setting the Hardware

Step 3 Installing the Hardware

Step 4 Initializing the Software

Step 5 Operation Checks

If Setup fails to be performed normally, see the “Setup Troubleshooting” section at the end of this

chapter.

2. Setup

10

GW1-ETH-WQ-EU, GW1-ETH-WQ-US

Step 1 Installing the Software

Install the driver library before connecting this product to your PC.

The installing driver library defers depending on the setting terminal (Slave).

Configure the setting terminal (Slave) first.

2. Setup

GW1-ETH-WQ-EU, GW1-ETH-WQ-US

11

Step 2 Setting the Hardware

This section describes how to set the product and plug it on your PC.

Product Nomenclature

Component names of the product are shown in the figure below.

Figure 2.1. Name

No.

Name

1

Power connector

2

mini-B USB connector

3

INIT button

4

Antenna connector

5

WLINK LED

6

Ethernet connector

7

DIP switch (for maintenance) *1

*1 Do not touch DIP switch since this is not used for usual operations.

There is a cover for the switch on the back side of the product.

⑤

⑦

Front

Back

Bottom

⑥

① ② ③

④

Top

Gat eway

2. Setup

12

GW1-ETH-WQ-EU, GW1-ETH-WQ-US

Name and Function

Power Connector

Use the power connector, included in the package, to supply power (use the power cable described

below or equivalent one).

Attached connector: European type terminal 3.5 pitch 3-pin jack connector

Supplied connector: European type terminal 3.5 pitch 3-pin plug connector

Compatible cable: AWG28 - 16(Cable length should satisfy the power specification including

the cable voltage drop)

Signal name

Description

V+

Power supply (12 - 24VDC±5%)

V-

Power supply (GND)

FG

Frame ground

-

When making the power cable, be sure to make the wiring correctly.

Especially, if the wrong housing pin number is used, it may cause malfunction or accidents.

-

Input voltage range: 12 - 24VDC

±

5%

Use the power supply that rises within the input voltage range of 11.4 VDC or higher and within 10 ms.

Otherwise, the product may be damaged or cause a failure.

Figure 2.2. Power input time

Vi+ Vi- FG

12-24VDC

10 Time

(ms)

11.4

12

24

Input voltage

(V)

～

2. Setup

GW1-ETH-WQ-EU, GW1-ETH-WQ-US

13

INIT button

Name

Description

INIT

This is used to initialize (restore the factory settings) the product. If

this button is pressed for three seconds or longer, LED of WLINK

starts flashing in orange. If the button is released before the

flashing stops, all the settings of the product are restored to the

factory settings after rebooting the product.

* When initializing the product with INIT button, flashing continues for a while. This indicates that files in the built-in memory are being

removed. If you turn off the power before flashing stops, the files in the built-in memory are damaged and this might prevent the product

from booting properly. Always reboot the product after flashing stops.

“WLINK”LED Indicator

LED name

LED color

Status

Description

WLINK

Green

ON

It indicates that the device is operating.

Green

Flashing

It indicates that the device is being

started (from power-on up to operation)

---

OFF

It indicates that the device is power off.

Orange

ON

It indicates that the device is operating.

(wireless connection)

Orange

Flashing

Write file

Red

Flashing

System error

WLINK

2. Setup

14

GW1-ETH-WQ-EU, GW1-ETH-WQ-US

Ethernet connector

This product has 1 port of Ethernet connector. The specification is described below.

-

Network type: 100BASE-TX/10BASE-T

-

Transmission speed: 100M/10Mbps

-

Maximum network path length: 100m/segment

-

IP address: 192.168.0.1 (default value)

Pin No.

Signal Name

Description

1

TX+

Transmission data (+) output

2

TX-

Transmission data (-) output

3

RX+

Reception data (+) input

4

N.C.

This pin is left unconnected.

5

N.C.

This pin is left unconnected.

6

RX-

Reception data (-) input

7

N.C.

This pin is left unconnected.

8

N.C.

This pin is left unconnected.

LED Indicator of Ethernet connector

LED

Status

Description

Speed

(Orange)

ON

It indicates that LAN port is connected at 100Mbps.

OFF It indicates that LAN port is connected at 10Mbps or not

connected.

Link /Act

(Green)

ON

It indicates that LAN port is in a connecting state.

Flashing It indicates that LAN port transmitting and receiving data

with the connected external device.

OFF

It indicates that LAN port is not connected.

8 1

Link /ActSpeed

2. Setup

GW1-ETH-WQ-EU, GW1-ETH-WQ-US

15

DIP switch

This is a DIP switch for maintenance. Do not use this.

Pin No.

Description

1

Always OFF

2

Always OFF

1 O

N

2

Page is loading ...

Contec GW1-ETH-WQ-US Owner's manual

This manual is also suitable for

Contec GW1-ETH-WQ-US Owner's manual

Related papers

Other documents