ifrogz AIRTIME Owner's manual

Type
Owner's manual

ifrogz AIRTIME's True Wireless earbuds free you to experience and enjoy music without the hassle of wires and plugs. With 3 listening settings—Signature Sound, Podcast, and Bass Boost—you can customize your audio experience, and easily switch between them with a simple press of a button. Seamlessly navigate music and calls with the intuitive controls on each earbud, including play/pause, next/previous song, answer/end calls, and activate Siri or voice command.

ifrogz AIRTIME's True Wireless earbuds free you to experience and enjoy music without the hassle of wires and plugs. With 3 listening settings—Signature Sound, Podcast, and Bass Boost—you can customize your audio experience, and easily switch between them with a simple press of a button. Seamlessly navigate music and calls with the intuitive controls on each earbud, including play/pause, next/previous song, answer/end calls, and activate Siri or voice command.

TRULY WIRELESS EARBUDS
Manual
AIRTIME Earbuds Instructions
Introduction
Welcome to Truly Wireless Audio. Now, you never need to plug your earbuds in again.
AIRTIME True Wireless earbuds free you to enjoy music without anything holding you back.
Pairing the Wireless Earbuds with Your Device
1. Simply open the case and a pairing signal will be sent to your Bluetooth® device. The left
earbud will flash white, indicating pairing mode.
2. Ensure your device’s Bluetooth® connection is on and select “IFROGZ AIRTIME.”
3. Complete any additional paring steps based on your device. The earbuds’ lights will turn o
indicating that pairing was successful. Congrats, your wireless earbuds are now ready to use!
You can also turn on pairing mode by pressing the button in the charge case for 5 seconds.
Turning Earbuds On/Off
To turn the earbuds on, simply open the case and close the case.
If you’d like to turn an individual bud on, press and hold the button on it for 3 seconds. It will flash
white until it’s connected to a device. It will turn o if not paired within 60 seconds.
To turn earbuds o, simply return them to the case. You can also press and hold the button on the
earbud for five seconds to turn it o; it will flash red indicating power is o.
The earbuds will go into hibernation mode if not used for 20 minutes.
Using the Earbuds
The circle on each bud is a button you can use to navigate music and calls. Here’s how to use it.
Play/Pause = Quick press
Next Song = Double press the right earbud.
(Note: This only works when the music is playing.)
Previous Song = Double press the left earbud.
(Note: This only works when the music is playing.)
Answer Call = Quick press
End Call = Double press
Cancel Call = Press and hold for two seconds
Siri or Voice Command = Double press (Note: This only works when music is not playing and
there’s no
connection nearby.)
Switch EQ = Press for 1-2 seconds, a voice will indicate a new setting. (Note: This only works when
music is playing.)
Third Party Calls:
End current call and answer new call = Quick press
Reject new call = Press for one second
Answer new call but hold current call = Double press
Switch between calls = Double press. A tone will sound.
How to Manage EQ
Your AIRTIME True Wireless Earbuds come with three listening settings: Signature Sound,
Podcast, and Bass Boost. To switch your setting, press the button on the earbud for 1-2 seconds.
A voice will indicate the
new setting. The earbuds must be in music mode to change EQ.
Earbud Color Guide
Flashing White = Pairing
White = Paired
Red = Charging
Flashing Red = Low battery. Will flash every two minutes
and a tone will sound
Charging the Wireless Earbuds
The case carries enough power to charge the earbuds up to 4 times.*
To charge them:
1. Place them in the charge case.
2. A red light on the earbuds will indicate charging. When the red light disappears, they are
fully charged
3. Recharge the case, if needed
*Based on 50% volume and 5 charges from the case to the earbuds of 3 hours of playtime.
Charging the Case
Your case comes charged and ready to go, but here’s how to recharge it when you need to:
1. Connect the included USB charging cable to the micro USB port on the back of your case.
2. Connect the USB end of the included cable to your preferred 5V USB outlet.
3. The Battery Indicator inside the case will flash according to its current battery level. This
indicates your case is charging.
4. Wait for the Battery Indicator lights to turn o, indicating your case is fully charged.
5. Disconnect the charging cable and enjoy your new, portable power.
AIRTIME Earbuds Instructions
Checking the Battery Level
Your case carries enough power for you to enjoy your wireless earbuds up to 4 times, for a total
of up to 15 hours. To check how much power it still carries:
1. Open the top of the case.
2. Press the battery button. The LED display will light according to how much battery remains:
a. The Battery Indicator inside the case will flash according to its current battery level. This
indicates your case is charging.
b. Wait for the Battery Indicator lights to turn o, indicating your case is fully charged.
c. Disconnect the charging cable and enjoy your new, portable power.
3. Recharge your case whenever you wish.
Troubleshooting
It’s not likely you will have trouble connecting your buds, but due to interference with other
wireless signals, sometimes an extra step is needed.
Please follow these steps to reset the buds and sync them with your device:
1. When you open the case, the left earbud LED will flash indicating pairing mode. If the left
earbud does not flash for auto-pairing, a manual connection needed.
2. For a manual connection, take the earbuds from the case and hold both buttons for 5
seconds to turn them o.
3. After waiting a moment, press and hold the buttons for 7 seconds or until the white LEDs
begin to flash.
4. Next, place the buds back in the case and wait a moment. The buds are now synced to
each other and ready to pair with your device. Please reference the quick start guide for the
standard pairing procedure.
If you are still experiencing pairing issues, we suggest a full factory reset.
1. Finally, open your device’s Bluetooth® settings and turn o the Bluetooth® feature. Wait a
moment, then turn it back on. Sometimes your device requires a restart. You can also restart
your device by shutting it down then powering it back on.
AIRTIME Earbuds Instructions
©2019 ZAGG Inc All Rights Reserved / Tous Droits Réservés / Todos los derechos reservados | NASDAQ: ZAGG | MADE IN CHINA / Fabriqué
en Chine / Hecho en China
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by ZAGG Inc is
under license. Other trademarks and trade names are those of their respective owners. Trademarks are property of ZAGG IP Holding Co., Inc.
La marque et le logo Bluetooth® sont des marques déposée de Bluetooth SIG, Inc. et toute utilisation de ces marques par ZAGG Inc est sous
licence. Les marques commerciales sont la propriété de ZAGG IP Holding Co., Inc.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED
MODIFICATIONS OR CHANGE TO THIS EQUIPMENT. SUCH MODIFICATIONS OR CHANGE COULD VOID THE USER’S
AUTHORITY TO OPERATE THE EQUIPMENT.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End user must
follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or
operating in conjunction with any other antenna or transmitter.
Drivers / Pilotes / Conductores: 8mm | Resistance / Résistance / Resistencia: 32 Ohms Sensitivity / Sensibilité /
Sensibilidad: 96dB ± 3dB Frequency / Fréquency / Frecuencia: 20Hz - 20KHz Working Time / Heures de travail
continuous / Tiempo de trabajo: 15h Charging Time / Temps de charge / Tiempo de trabajo: 1.5-2h
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13

ifrogz AIRTIME Owner's manual

Type
Owner's manual

ifrogz AIRTIME's True Wireless earbuds free you to experience and enjoy music without the hassle of wires and plugs. With 3 listening settings—Signature Sound, Podcast, and Bass Boost—you can customize your audio experience, and easily switch between them with a simple press of a button. Seamlessly navigate music and calls with the intuitive controls on each earbud, including play/pause, next/previous song, answer/end calls, and activate Siri or voice command.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI