Frigidaire 5304503339 User guide

use

care

FOOD WASTE DISPOSER

English ..............................................................2

Français ........................................................... 15

Espanol .......................................................... 29

p/n 5304525393

Record important disposer information here:

Model Number* Serial Number*

NOTE

This Food Waste Disposer has been designed to operate on

110-120V, 60 Hz exclusively. Using any other voltage or Hz ad-

versely a ects performance.

CAUTION

Be sure to review SAFETY INSTRUCTIONS FIRST

PERTAINING TO A RISK OF FIRE, ELECTRICAL SHOCK

OR INJURY TO PERSONS before using disposer.

IMPORTANT

Read all instructions thoroughly. Keep this guide for

future reference.

*Above information appears on the label a xed to bottom

of the disposer. For your convenience, write down the

model and serial number prior to installation.

IMPORTANT SAFETY INFORMATION

WARNING

When using electrical appliances, basic

precautions should always be followed,

including the following:

INSTRUCTIONS PERTAINING TO A RISK OF FIRE,

ELECTRIC SHOCK OR INJURY TO PERSONS. SAVE

THESE INSTRUCTIONS.

1. Read all instructions before using the appliance.

2. To reduce the risk of injury, close supervision is necessary

when an appliance is used near children.

3. Do not put ﬁ ngers or hands into a waste disposer.

4. Turn the power switch to the o position before

attempting to clear a jam or remove an object from the

disposer.

5. When attempting to loosen a jam in a waste disposer, use

a long wooden object such as a wooden spoon or the

wooden handle of a broom or mop.

6. When attempting to remove objects from a waste

disposer use long-handled tongs or pliers. If the disposer

is magnetically actuated, non-magnetic tools should be

used.

7. To reduce the risk of injury by materials that may be

expelled by a waste disposer, do not put the following

into a disposer: clam or oyster shells; caustic drain

cleaners or similar products; glass, china or plastic;

large whole bones; metal, such as bottle caps, tin cans,

aluminum foil or utensils; hot grease or other hot liquids;

whole corn-husks.

8. When not operating a disposer, leave the stopper in place

to reduce the risk of objects falling into the disposer.

9. DO NOT operate disposer unless splash guard is in place.

10. For proper grounding instructions see the ELECTRICAL

CONNECTIONS portion of this manual.

11. If the supply cord is damaged, it must be replaced by the

manufacturer, its service agent, or authorized person in

order to avoid hazard.

12. This appliance is not intended for use by persons

(including children) with reduced physical, sensory or

mental capabilities, or lack of experience and knowledge,

unless they have been given supervision or instruction

concerning use of the appliance by a person responsible

for their safety.

13. Children should be supervised to ensure that they do not

play with the appliance.

The receptacle to which this appliance is connected

must be controlled by a switch.

Having Problems? Don't go back to the store.

Call us toll-free at 1-833-240-6224 for assistance.

M-F 8:00am-5:00pm PST English & Spanish

3-BOLT MOUNTING SYSTEM

REMOVAL OF OLD UNIT

IMPORTANT

This is a good time to clean out the trap and drain lines by

running a drain auger or plumber’s snake before installing

your new disposer.

CAUTION

Be sure to support the disposer while performing this step or

it may fall when the mounting ring is disconnected from the

mounting assembly.

1. REMOVAL OF OLD UNIT

TYPICAL INSTRUCTIONS, YOUR MODEL MAY VARY.

Before starting this step, turn o electrical

power at the circuit breaker or fuse box. Unplug

disposer.

If your installed mount is the same type as the mount on your

new disposer and you wish to continue to use the already

installed mount, proceed to section 3 on the Connection page.

If your new mount system is di erent or if you wish to use the

new mount, follow these instructions:

A. Have a container available to catch any excess water/

waste from current disposer. Use a pipe wrench to

disconnect drain line where it attaches to disposer

discharge elbow (see 1A).

B. Remove disposer from sink ﬂ ange by turning mount

ring to the left clockwise (see 1B). If you are unable to

turn the mount ring, tap on one of the extensions from

the ring with a hammer. Some mounting systems have

tubular extensions. Inserting a screwdriver into one tube

will provide additional leverage for turning the mount

ring (see 1B).

C. Some disposers may require the removal or loosening

of nuts from the mount screws (see 1C). Some disposers

may require the removal of a clamp.

D. To remove remaining mount system from the sink, loosen

mount screws, push mount ring up. Under it is the retainer

ring. Use screwdriver to pop o ring (see 1D). Remove

mount ring, protector ring and gasket from sink ﬂ ange.

Some mounts will require the unscrewing of a large

ring holding the sink ﬂ ange in place. Pull sink ﬂ ange up

through sink and clean o old putty from sink.

E. Ensure that sink is clean and thoroughly dry.

If you have a mount system under the sink that

is black plastic with threads:

A. While holding the disposer in place, turn the metal

mount ring clockwise (1E). If it is hard to turn, tap the

ear of the mount ring clockwise.

B. When the disposer hopper projections get close to the

mount ring opening, hold the disposer from bottom and

disengage it from the mount ring.

C. Remove the rubber cushion mount from under the

mount ring.

D. Remove the mount ring. Unthread the black support

ring from sink ﬂ ange by turning the support ring

clockwise. Remove the ﬁ ber gasket and then remove

the sink ﬂ ange from above the sink.

E. Ensure that sink is clean and thoroughly dry.

Mount With Threaded Flange

4INSTALLATION

A STOPPER

BREMOVABLE

SPLASH GUARD

CSINK FLANGE

DFIBER GASKET

ESUPPORT

FLANGE

FUPPER

MOUNT RING

GMOUNT

SCREWS

HRETAINER RING

I CUSHION RING

JLOWER

MOUNT RING*

SILVER GUARD®

MAGNETIC

CATCH RING**

2. INSTALLATION OF MOUNTING ASSEMBLY

**ATTACHMENT INCLUDED WITH MOST

CONTINUOUS FEED 3/4 HP & 1-¼ HP MODELS.

Installation instructions on last page.

READ CAREFULLY AND COMPLETELY BEFORE

STARTING

NOTE

As the mounting assembly is properly assembled at the

factory, please pay close attention to the order of the mount-

ing system parts.

NOTE

Cushion Ring included between the Upper Mount Ring and

Lower Mounting Ring.

* Part not disengaged during disposer installation.

INSTALLATION (CONTINUED)

A. The Cushion Ring and the Lower Mount Ring will remain

attached to the disposer during installation. Take apart

the other parts of the mounting assembly by rotating the

Lower Mount Ring clockwise until the Lower Mount Ring

Tabs slide o from the Upper Mount Ring ramp (see A1).

This allows you to pull the Sink Flange up and out of the

remaining Lower Mount Assembly. Note the order of these

parts as they are arranged in the required order. Unscrew

the 3 Mount Screws until the Upper Mount Ring can be

moved to the top of the Support Flange. Remove the

Retainer Ring with a ﬂ at head screw driver (see A2).

B. Keep the remaining parts placed together in the order

they were removed (see B1). Before you connect the

disposer to the mount assembly under the sink, make sure

the Lower Mount Ring is in place and the black Cushion

Ring is still engaged properly to the top of the disposer

hopper (see B2).

C. Be sure the sink is clean. Load the underside rim of the

sink ﬂ ange with plumber’s putty (see C1). From top of

the sink, push the sink ﬂ ange down against the sink

opening to make a good seal (see C2). DO NOT MOVE

OR ROTATE the sink ﬂ ange once it has been seated or

the seal may be broken.

D. Place a heavy object, such as the disposer

(use a towel to prevent sink scratching) on

top of the Sink Flange to hold it down.

E. Take the remaining portion of the mount assembly that was

put aside. From under the sink insert the Fiber Gasket (see

E1), then the Support Flange (see E2), and then the Upper

Mount Ring (see E3).

F. Hold the three parts in place while attaching the Retainer

Ring (see F1) by pulling it apart and having it snap within

the groove of the sink ﬂ ange (see F2).

G. Tighten the three Mount Screws evenly and ﬁ rmly against

the Support Flange (see G1). Do not over tighten.

H. Trim o any excess plumber’s putty in the sink with a

plastic knife or something similar that will not damage your

sink.

INSTALLATION (CONTINUED)

Having Problems? Don't go back to the store.

Call us toll-free at 1-833-240-6224 for assistance.

M-F 8:00am-5:00pm PST English & Spanish

3. DISHWASHER CONNECTION PREPARATION

CONNECTION

If you are utilizing a dishwasher, complete the

following procedure.

Using a blunt instrument (steel punch or wooden dowel),

knock out entire plug. Do not use a screwdriver or sharp

instrument. (When knockout plug falls into disposer, you may

remove it or grind it up when the disposer is used. This will

not damage the disposer in any way, but it may take some

time to grind).

4. LOCKING MOUNTING ASSEMBLY DETAIL

Attach disposer onto the Upper Mount Ring by aligning

the three mount tabs on the Lower Mount Ring with the

slide-up Ramps on the Upper Mount Ring and rotating

counterclockwise. See Below.

The Lower Mount Ring (which is part of the disposer) has 3

tabs that grab the mounting ring ramp.

(A) points to the Upper Mount Ring.

(B) is the tab that slides up onto the “Ramp”.

Mount Ring.

Use a screwdriver for leverage if needed.

Lift and turn the Lower Mount Ring counterclockwise until

all three mount tabs lock over the Ridges (F) on the slide-up

Ramps (D) of the Upper Mount Ring.

As the Lower Mount Ring is turned counterclockwise each tab

slides up onto the Upper Mount Ring Ramp (E) and locks in

position over the Ridges (F).

Use a screwdriver or hammer for leverage if needed.

If a disposer needs to be removed, tapping on the Ear clockwise

with a hammer will easily loosen the Lower

Mount Ring.

5. DISCHARGE ELBOW &

DISHWASHER CONNECTIONS

A. Connect the waste elbow to the disposer by sliding

the ﬂ ange against the rubber gasket on the elbow and

tightening the screws into the disposer (see 5A). Then

connect bottom of the elbow by tightening the slip

nut (see 5B). If using a straight pipe, it must have a lip

similar to the one on the elbow. Remove the gasket

from the elbow and install it on the straight pipe with

the ﬂ at end of the gasket facing toward the disposer

discharge opening. IF YOU ARE NOT CONNECTING TO

A DISHWASHER make sure all plumbing connections

are tight and in accordance with all plumbing codes and

ordinances. Run water and check for leaks. Go on to

Step 6.

KNOCK OUT

PLUG

WOOD OR

METAL DOWEL

B. Connect dishwasher hose (see 5C) using hose clamp.

Make sure all plumbing connections are tight and in

accordance with all plumbing codes and ordinances. Run

water and check for leaks.

CONNECTION (CONTINUED) & GROUNDING INSTRUCTIONS

6. ELECTRICAL CONNECTIONS

A. Connect disposer to appropriate household current only.

WARNING

IMPROPER CONNECTION OF THE EQUIPMENT-

GROUNDING CONDUCTOR CAN RESULT IN A RISK

OF ELECTRIC SHOCK. CHECK WITH A QUALIFIED

ELECTRICIAN OR SERVICEMAN IF YOU ARE IN

DOUBT AS TO WHETHER THE APPLIANCE IS

PROPERLY GROUNDED. DO NOT MODIFY THE

PLUG PROVIDED WITH THE APPLIANCE IF IT WILL

NOT FIT THE OUTLET. HAVE A PROPER OUTLET

INSTALLED BY A QUALIFIED ELECTRICIAN.

The receptacle to which this appliance is

connected must be controlled by a switch.

Grounding Instructions

FOR WASTE DISPOSERS EQUIPPED WITH A

GROUNDED PLUG-IN POWER CORD.

B. This appliance must be grounded. In the event of a

malfunction or breakdown, grounding provides a path

of least resistance for electric current to reduce the

risk of electric shock. This appliance is equipped with

a cord having an equipment-grounding conductor and

a grounding plug. The plug must be plugged into an

appropriate outlet that is properly installed and grounded

in accordance with all local codes and ordinances. If

the supply cord is damaged it must be replaced by the

manufacturer, its service agent or similarly qualiﬁ ed person

in order to avoid a hazard.

PERMANENT WIRE INSTALLATION

INSTRUCTIONS

For waste disposers NOT equipped with a

grounded plug-in power cord.

GROUNDING: This disposer must be connected to a

grounded, metal, permanent wiring system; or an equipment-

grounding conductor must be run with the circuit conductors

and connected to the equipment-grounding terminal or lead on

the disposer.

An acceptable motor control switch with a marked o position

shall be provided at the time of installation to disconnect the

disposer from all ungrounded supply conductors. The switch

shall be mounted in sight of the disposer or in sight of the sink

opening for the disposer.

WARNING

Electric Shock

Turn o power before installing or servicing disposer. All

wiring must comply with local electrical codes.

Do not connect electrical current at main breaker panel until

adequate ground is established. Inadequate connection of

the ground wire can result in a risk of electric shock. Consult

with a certiﬁ ed electrician or tradesman if there is any doubt

whether the disposer in inadequately grounded. Your

disposer must be adequately grounded.

GROUNDING INSTRUCTIONS (CONTINUED)

1. Turn o or disconnect all power to the wall junction box

serving the disposer.

2. Open the junction box in the wall and remove the wire

nuts or electrical tape or whatever is tying the old

disposer wire to the electrical wire inside of the junction

box.

3. Open the end bell plate at the bottom or the disposer.

If you are using ﬂ exible armored (BX) cable:

1. Install cable ﬁ tting in the disposer end bell hole.

2. Secure the cable to the ﬁ tting and install an insulating

bushing or equivalent.

3. Connect white wire from the junction box to the white

(or blue) wire of the disposer.

4. Connect black wire from the junction box to the black (or

brown) wire of the disposer.

5. Connect bare ground wire from the junction box to green

ground screw within the disposer end bell.

If you are using nonmetallic-sheathed (ROMEX)

cable:

1. Install cable ﬁ tting in the end bell hole and secure the

cable to the ﬁ tting.

2. Connect white wire from the junction box to the white

(or blue) wire of the disposer.

3. Connect black wire from the junction box to the black (or

brown) wire of the disposer.

4. Connect bare ground wire from the junction box to green

ground screw within the disposer end bell.

If your power supply cable does not include a grounding wire,

one must be provided. Attach a copper wire securely to the

disposer ground screw and attach other end of ground wire

to a metal cold water pipe. Do not attach ground wire to a gas

supply pipe. Use only UL Listed grounding clamp. If plastic

pipe is used in your home, a qualiﬁ ed electrician should install a

proper ground.

Having Problems? Don't go back to the store.

Call us toll-free at 1-833-240-6224 for assistance.

M-F 8:00am-5:00pm PST English & Spanish

123

879

456

1. After turning o power

supply, unbolt two nuts

and remove end plate.

2. Using a ﬂathead

screwdriver or needle nose

pliers, remove clip from strain

relief portion of the cord.

3. Using wire cutters, cut black

(or brown) wire and white (or

blue) wire near the connectors.

4. Pull cord strain relief out

of endbell. Cut green

ground wire near the cord

strain relief.

5. Insert metal strain relief

connector (not included)

into the endbell hole and

tighten the nut securely.

6. Strip the green, black, and

white insulation from last ½”

of each wire.

7. Insert the power supply

cable, coming from the

wall junction box,

through the strain relief

connector. Tighten

connector.

8. Connect disposal wire leads

(black and blue) to

corresponding wire leads of

the power supply cable.

Green always connects to

green.

9. Setting the wires into

the endbell, replace the

end plate and tighten the

two bolts.

PERMANENT WIRE INSTALLATION

1111

Your disposer is Continuous Feed if you did not speciﬁ cally

purchase a Batch Feed Disposer.

7. OPERATING INSTRUCTIONS

CONTINUOUS FEED

The Anti-Jam Swivel Impellers make a clicking

sound as they initially swing into place. This

indicates normal operation.

A. Remove sink stopper. Turn on a medium ﬂ ow of

cold water.

B. Turn switch to ON position; your motor is turning at full

speed and ready to use.

C. Scrape in food waste. Down the drain go table scraps,

peelings, rinds, seeds, pits, small bones and co ee

grounds. To speed up food waste disposal, cut or break

up large bones, rinds and cobs. Large bones and ﬁ brous

waste require considerable grinding time and are more

easily thrown away with other trash. Do not be alarmed

that the disposer slows down while grinding. The disposer

is actually increasing torque (grinding power) and is

operating under normal conditions.

D. Before turning disposer o , let water and disposer run

for approximately 15 seconds after shredding or grinding

stops. This assures that all waste is thoroughly ﬂ ushed

through trap and drain.

E. It is not recommended to use hot water while running

disposer. Cold water will keep waste and fats solid so

disposer can ﬂ ush away particles.

BATCH FEED

A. Remove sink stopper and turn on a medium ﬂ ow of cold

water.

B. Scrape in food waste. Down the drain go table scraps,

vegetable peelings, cobs, rinds, pits, bones and co ee

grounds (see A).

C. Insert stopper to start disposer (see B). One of the two

small slots in stopper base must line up with switch

plunger inside the neck of the disposer. Push down ﬁ rmly

to turn the disposer on. Lift stopper to shut the disposer

o .

D. Run disposer for 15 seconds after shredding stops. This

ensures that all waste is thoroughly ﬂ ushed through the

drain.

E. To ﬁ ll sink, insert stopper and align the largest slot with

the switch plunger (see C). Push down to seal sink

without starting the disposer. When the large sized slot

in stopper base is lined up with the switch plunger, water

can drain, but tableware, etc., cannot be accidentally

dropped into disposer.

TIPS FOR SUCCESSFUL OPERATION

A. Be sure disposer is empty before using your dishwasher

so it may drain properly.

B. You may want to leave the stopper in the sink drain when

not in use to prevent utensils and foreign objects from

falling into the disposer.

C. Your disposer is ruggedly built to give you many years of

trouble free service. It will handle all normal food wastes,

but it will NOT grind or dispose of such items as plastic,

tin cans, bottle caps, glass, china, leather, cloth, rubber,

string, clam and oyster shells, aluminum foil or feathers.

OPERATION

12 CLEANING AND MAINTENANCE

DO NOT ATTEMPT TO LUBRICATE

YOUR DISPOSER!

The motor is permanently lubricated. The disposer is self cleaning

and scours its internal parts with each use. NEVER put lye or

chemical drain cleaners into the disposer, as they cause serious

corrosion of metal parts. If used, resulting damage can be easily

detected and all warranties are void. Mineral deposits from

your water can form on the stainless steel turntable, giving the

appearance of rust. DO NOT BE ALARMED, the stainless steel

turntables used will not corrode.

Having Problems? Don't go back to the store.

Call us toll-free at 1-833-240-6224 for assistance.

M-F 8:00am-5:00pm PST English & Spanish

TROUBLESHOOTING

Before seeking repair or replacement, we recommend that you

review the following:

LOUD NOISES: (Other than those during grinding of small

bones and fruit pits): These are usually caused by accidental

entry of a spoon, bottle cap or other foreign object. To correct

this, turn o electrical switch and water. After disposer has

stopped, remove splash guard, remove object with long handled

tongs, and replace splash guard.

UNIT DOES NOT START: Unplug power cord or turn either the

wall switch or breaker box switch to “OFF” position, depending

on your model and wiring conﬁ guration. Remove stopper and/or

splash guard. Check to see if turntable will rotate freely using a

wooden broom handle. If turntable rotates freely, replace splash

guard and check reset button to see if it has been tripped. Reset

button is red and located on the front of the disposer. Push

button in until it clicks and remains depressed.

If reset button has not been tripped, check for shorted or

broken wire connecting to disposer. Check electrical power

switch, fuse box or circuit breaker. If wiring and electrical

components are intact, the unit may have internal problems that

require service or replacement.

IF TURNTABLE DOES NOT ROTATE FREELY: Turn o disposer,

then check for any foreign object lodged between the turntable

and grind ring. Dislodge object by rotating table with a wooden

broom handle (see 8A) and remove object. If no foreign object

is present, there may be internal problems.

LEAKS: If the unit leaks at the top, it may be due to:

1. Improper seating of sink ﬂ ange (gasket centering, putty

or tightening).

2. Support ﬂ ange not tightened properly.

3. Defective or improperly installed cushion mount.

If unit leaks at the waste elbow, leak may be due to improper

tightening of elbow ﬂ ange screws.

1313

*Approximate Dimension

1/3 HP, 1/2 HP & 3/4 HP Slim-

Line Models 10.2 in

3/4 HP Deluxe 10.5 in

1-1/4 HP Premium 10.5 in

Batch Feed units add approx. 2.1”/53mm

TYPICAL INSTALLATIONS

MOUNTING THE SILVER GUARD® MAGNETIC

CATCH RING

After the disposer is fully mounted to the sink, guide the

Magnetic Silver Guard® through the mount screws (6A)

with the ﬂ at portion of the black strap facing the metal sink

ﬂ ange. Place the Silver Guard® between the Support Flange

and Upper Mount Ring. Please note (6B) that the Silver

Guard® must be placed under the ﬂ ange of the Support

Ring. Once the Silver Guard® is ﬁ tted, ﬁ rmly press on the

snaps to secure the strap (6C).

For your speciﬁ c disposer dimensions, contact

Frigidaire customer service at 1-833-240-6224.

www.frigidaire.com USA 1-800-374-4432 www.frigidaire.ca Canada

14 LIMITED LIFETIME WARRANTY AGAINST FAILURE DUE TO CORROSION

1-833-240-6224

10200 David Taylor Drive

Charlotte, NC 28262

Model Horsepower Warranty Period

1/3 HP 5 years

1/2 HP 6 years

3/4 HP 10 years

1-1/4 HP 12 years

Proof of purchase is required! Staple receipt or proof of purchase to this manual. Tracking is handled through the

serial number a xed to the bottom of the disposer and/or on the power cord label.

Conveniently record your model number and serial number on the front of this manual for your records. If

you need warranty service, call us toll-free at 833-240-6224. Have serial number and receipt available for the

technician. Warranty is non-transferable.

1. WARRANTY: Frigidaire disposers are warranted when installed in the United States to be free from defects in workmanship

and material during the warranty period. This warranty sets forth our overall warranty commitment. We will not assume, nor

authorize any person to assume for us, any other liability in connection with the sale of our products. Warranty only valid for

product sold through authorized dealers/retailers.

2. LENGTH OF WARRANTY: 1/3 HP MODELS - 5 years from date of purchase. 1/2 HP MODELS - 6 years from date of

purchase. 3/4 HP MODELS - 10 years from date of purchase. 1 ¼ HP MODELS - 12 years from date of purchase. Models that

fail to operate during its warranty period, will be repaired or replaced. This Warranty includes In-Home Warranty for Frigidaire

models that fall into disrepair due to manufacturing defect. This warranty is limited to the original purchaser. Original sales

receipt required.

3. DEFECTIVE DISPOSER: During the warranty period, a defective or inoperative disposer will be replaced by the company

at no charge to the consumer/purchaser. Original sales receipt required. The warranty on the replacement will be limited

to the unexpired term of the warranty on the original disposer.

4. CHANGE OF OWNERSHIP DISPOSER: Warranty remains in force for warranty period from date of purchase of disposer

by the original retail customer. Warranty is non-transferable. Original sales receipt required.

5. MISUSE OF DISPOSER: This warranty does not apply to any disposer which is misused, altered, improperly installed

or used for anything other than normal residential use. Additional conditions not covered by the warranty are as follows:

Electrical connections due to improper installation; leaks at the sink ﬂ ange, dishwasher inlet or discharge elbow; damage by

installer such as excessive torquing of screwed connections; incorrect operation such as grinding nonfood waste; and jams.

6. HOW TO RECEIVE SERVICE: Contact our Customer Service department: Toll Free: (833-240-6224).

7. LIFETIME CORROSION WARRANTY: In addition to above warranty, any disposer that fails to operate because of

corrosion will be replaced. This Lifetime Corrosion warranty is limited to the original purchaser. Original sales receipt is

required.

8. MODEL NUMBER AND SERIAL NUMBER: The model number and serial number are located on the bottom serial plate of

your disposer and/or the power cord tag. Always reference the model number and serial number when contacting customer

service about any warranties on your disposer.

9. IMPLIED WARRANTIES: IMPLIED WARRANTIES, INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO WARRANTY PERIOD FROM THE DATE OF

PURCHASE. Some states do not allow limitations on how long an implied warranty lasts, so therefore the above limitation may

not apply to you.

10. CONSEQUENTIAL OR INCIDENTAL DAMAGES: THE COMPANY SHALL NOT BE LIABLE FOR CONSEQUENTIAL OR

INCIDENTAL DAMAGES FOR ANY BREACH OF WARRANTY, EXPRESS OR IMPLIED. Some states do not allow the exclusion

or limitation of the consequential or incidental damages, so therefore the above exclusion may not apply to you.

11. EXCLUSIVE REMEDY; CONSEQUENTIAL DAMAGES: The foregoing provisions state the exclusive remedy for any

breach of warranty, express or implied, TO THE EXTENT PERMITTED BY LAW, THE COMPANY SHALL NOT BE LIABLE FOR

CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF WARRANTY, EXPRESS OR IMPLIED. Some states do not

allow the exclusion or limitation of consequential or incidental damages, so therefore the above exclusion may not apply to

you.

This warranty gives you speciﬁ c legal rights, and you may also have other rights which vary from State to State.

Having Problems? Don't go back to the store.

Call us toll-free at 1-833-240-6224 for assistance.

M-F 8:00am-5:00pm PST English & Spanish

www.frigidaire.com USA 1-800-374-4432 www.frigidaire.ca Canada

1-800-265-8352

BROYEUR À DÉCHETS

Manuel d'utilisation

Système de montage à 3 boulons

REMARQUE

Ce broyeur de déchets alimentaires a été conçu pour fonc-

tionner exclusivement sur une alimentation secteur de 110-

120V, 60 Hz. Tout autre tension ou fréquence risque d’altérer

ses performances.

AVERTISSEMENT

Assurez-vous de consulter les CONSIGNES DE SÉCURITÉ

PORTANT SUR LES RISQUES D'INCENDIE, DE CHOC ÉLEC-

TRIQUE OU DE BLESSURES avant d'utiliser ce broyeur.

IMPORTANT

Lisez attentivement toutes les instructions. Conservez

ce manuel pour consultation future.

Inscrivez ici les informations importantes concernant les broyeurs :

Numéro de modèle* Numéro de série

Anglais (2)

Français (15)

Espanol (29)

Vous avez un problème? Ne le retournez pas au magasin.

Appelez-nous sans frais au 1-833-240-6224 pour de l’assistance.

L-V 8:00am-5:00pm PST Anglais et Espagnol

*Les renseignements ci-dessus apparaissent sur l’étiquette ﬁ xée sous le

broyeur. Pour votre commodité,

prenez en note les numéros de modèle et de série avant l’installation.

16 IMPORTANTES CONSIGNES DE SÉCURITÉ

AVERTISSEMENT

Lors de l'utilisation d'appareils électriques,

des précautions de base doivent toujours être

prises, notamment les suivantes :

CONSIGNES RELATIVES AUX RISQUES

D'INCENDIE, D'ÉLECTROCUTION OU DE

BLESSURES. VEUILLEZ CONSERVER CES

CONSIGNES.

1. Lire attentivement toutes les instructions avant d'utiliser

l'appareil.

2. Pour réduire le risque de blessures, une étroite

supervision est nécessaire lorsqu'un appareil est utilisé à

proximité de jeunes enfants.

3. Ne pas mettre les doigts ou les mains dans un broyeur à

déchets.

4. Mettre l'interrupteur à la position d'arrêt avant de tenter

de débloquer ou de retirer un objet du broyeur.

5. Lorsque vous essayez de décoincer un bouchon dans

un broyeur à déchets, utilisez pour cela un long objet en

bois comme une cuillère en bois ou le manche en bois

d'un balai ou d'une serpillière.

6. Utiliser des pinces à longues poignées ou des pinces

de plombier pour enlever des objets le broyeur. Si le

broyeur est actionné magnétiquement, des outils non

magnétiques doivent être utilisés.

7. Pour réduire le risque de blessure par des matières

pouvant être expulsées par un broyeur de déchets,

évitez de mettre dans un broyeur les produits suivants

: coquilles de palourdes ou d'huîtres, nettoyants

caustiques pour canalisations ou produits similaires,

verre, porcelaine ou plastique, gros os entiers, métal, tel

que capsules de bouteilles, boîtes de conserve, papier

d'aluminium ou ustensiles, graisse chaude ou autres

liquides chauds, enveloppes de maïs entières.

8. Lorsque le broyeur n'est pas en fonction, laisser le

bouchon en place pour réduire le risque que des objets

tombent dans le broyeur.

9. Ne PAS faire fonctionner le broyeur lorsque le protecteur

anti-éclaboussures n'est pas en place.

10. Pour plus de détails sur les instructions de mise à la terre

voir la section RACCORDEMENT ÉLECTRIQUE de ce

manuel.

11. Si le cordon d'alimentation est endommagé, il doit

être remplacé par le fabricant, son représentant ou

une personne qualiﬁ ée de façon éviter tout risque

d'électrocution.

12. Cet appareil n'est pas destiné à être utilisé par des

personnes (y compris des enfants) dont les capacités

physiques, sensorielles ou mentales sont réduites ou

qui manquent d'expérience et de connaissances, sauf

si elles ont été encadrées ou ont reçu des instructions

concernant l'utilisation de l'appareil par une personne

responsable de leur sécurité.

13. Il est recommandé de surveiller les enfants aﬁ n de

s'assurer qu'ils ne jouent pas avec l'appareil.

Le réceptacle auquel est raccordé cet appareil

doit être contrôlé au moyen d’un interrupteur.

Vous avez un problème? Ne le retournez pas au magasin.

Appelez-nous sans frais au 1-833-240-6224 pour de l’assistance.

L-V 8:00am-5:00pm PST Anglais et Espagnol

IMPORTANTE

C'est un bon moment pour net-toyer les conduits d'évacua-

tion à l'aide d'un furet ou d'une sonde spirale avant d'installer

le nouveau broyeur

AVERTISSEMENT

Assurez-vous de soutenir le broyeur au cours de cette étape

car il pourrait tomber lorsque la bague de montage est dé-

connectée.

1. DÉMONTAGE DE L’ANCIEN APPAREIL

LES INSTRUCTIONS PEUVENT VARIER SELON LE

MODÈLE.

Avant de passer à l'étape suivante, coupez

l'alimentation électrique de la boîte de disjoncteurs ou

de fusibles. Débranchez le broyeur.

Si votre monture installée est du même type que celle de votre

nouveau broyeur et que vous souhaitez continuer à vous en

servir, passez à la section 3 de la page Connexion. Si votre

nouveau système de montage est di érent ou si vous souhaitez

utiliser la nouvelle monture, suivez les instructions suivantes :

A. Disposez d'un récipient pour récupérer l'excès d'eau ou

les déchets du broyeur actuel. Utilisez une clé à pipe pour

débrancher la tuyauterie d'évacuation à l'endroit où elle

se rattache au coude de décharge du broyeur (voir 1A).

B. Retirez le broyeur de la bride de l'évier en tournant

l'anneau de montage vers la gauche dans le sens des

aiguilles d'une montre (voir 1B). Si vous êtes incapable

de tourner la bague de montage, frappez sur l'une des

extrémités de la bague à l'aide d'un marteau. Certains

systèmes de montage ont des extrémités tubulaires.

L'insertion d'un tournevis dans un tube permet d'obtenir

un e et de levier supplémentaire pour faire tourner la

bague de montage (voir 1B).

C. Dans le cas de certains modèles de broyeurs, il se peut

que vous deviez enlever ou desserrer les écrous des vis

de montage (voir 1C). Dans le cas de certains broyeurs, il

est nécessaire de retirer la bride de serrage.

D. Pour retirer le reste du système de montage de l'évier,

desserrez les vis de montage, poussez l'anneau de

montage vers le haut. Le jonc de blocage se trouve en-

dessous. Utilisez un tournevis pour enlever le jonc (voir

1D). Enlevez la bague de montage, l'anneau de protection

et le joint d'étanchéité du collet d'évier. Certains

montages nécessitent le dévissage d'un gros anneau qui

tient en place le collet d'évier. Tirez le collet d'évier vers

le haut et enlevez le mastic usagé.

E. Assurez-vous que l’évier est propre et entièrement sec.

Si vous possédez un système de ﬁ xation sous l’évier

en plastique noir avec des ﬁ lets:

A. Tout en maintenant le broyeur en place, tournez

l'anneau de montage métallique dans le sens des

aiguilles d'une montre (1E). Si vous avez de la di culté

à le touner, frappez l’oreille de l’anneau de ﬁ xation dans

le sens horaire.

B. Lorsque les saillies de la chambre de broyage sont

près de l’ouverture de l'anneau de ﬁ xation, maintenez

le broyeur par le bas et désengagez-le de l’anneau de

ﬁ xation.

C. Retirez l’assemblage coussiné en caoutchouc sous

l’anneau de ﬁ xation.

D. Retirez l’anneau de ﬁ xation. Dévisser l’anneau de

support noir du collet d’évier en tournant l’anneau

de support dans le sens horaire. Retirez le joint

d'étanchéité en ﬁ bre puis retirez le collet d’évier de

l’évier.

E. Assurez-vous que l’évier est propre et entièrement sec.

Fixation avec collet vissé

DÉMONTAGE DE L’ANCIEN APPAREIL

A OBTURATEUR

PARE -

ÉCLABOUSSURES

AMOVIBLE

CCOLLET D’ÉVIER

DJOINT D’ÉTANCHÉITÉ

EN FIBRE

EBAGUE DE MONTAGE

FBAGUE DE MONTAGE

SUPÉRIEURE

GVIS DE FIXATION

HBAGUE DE RETENUE

IANNEAU COUSSINET

JBAGUE DE MONTAGE

INFÉRIEURE*

ANNEAU DE CAPTURE

MAGNÉTIQUE SILVER

GUARD®**

2. INSTALLATION DE L’ENSEMBLE DE FIXATION

**ACCESSOIRE INCLUS AVEC LA PLUPART DES

MODÈLES D'ALIMENTATION CONTINUE 3/4 HP & 1-1/4

HP. Instructions d'installation en dernière page.

REMARQUE

Comme l’ensemble de ﬁ xation est assemblé adéquatement

à l’usine, veuillez porter une attention particulière à l’ordre

d’assemblage des pièces du système de ﬁ xation.

REMARQUE

L’anneau coussinet inclus entre la bague de montage supé-

rieure et la bague de montage inférieure.

*Partie non désolidarisée lors de l'installation du

broyeur.

BAGUE DE MONTAGE

INFÉRIEURE

PATTE DE

MONTAGE

ENTRÉE DU LAVE-

VAISSELLE

BROYEUR ANNEAU COUSSINET

Protection

amovible contre les

Bride d’évier

Mastic de plomberie

Rainure

Joint d’étanchéité en ﬁ bre

Bride de soutien

Bague de montage supérieure

Vis de ﬁ xation

Bague de retenue

Bague à coussin

Bague de montage inférieure

Joint de caoutchouc

Coude

Bouton de réinitialisation

Bride de coude et

ensemble de vis

Évier

VEUILLEZ LIRE ATTENTIVEMENT ET COMPLÈTEMENT

AVANT DE DÉBUTER

INSTALLATION

A. L’anneau coussinet et la bague de montage inférieure

demeureront attachés lors de l’installation du broyeur.

Démontez les autres parties de l'ensemble de montage

en tournant l'anneau de montage inférieur dans le sens

des aiguilles d'une montre jusqu'à ce que les languettes

de l'anneau de montage inférieur glissent de la rampe

de l'anneau de montage supérieur (voir A1). Cela vous

permettra de retirer le collet d’évier de l’assemblage de

ﬁ xation inférieur. Notez l’ordre de ces pièces puisqu’elles

sont disposées dans l’ordre requis. Dévissez les 3 vis de

ﬁ xation jusqu’à ce que la bague de montage supérieure

puisse être déplacée vers le haut du collet d’évier. Retirez

la bague de retenue avec un tournevis à tête plate (voir

A2).

B. Gardez les parties restantes assemblées dans l'ordre

où elles ont été retirées (voir B1). Avant de connecter le

broyeur à l’assemblage de ﬁ xation sous l’évier, assurez-

vous que la bague de montage inférieure est en place et

que l’anneau coussinet noir est ﬁ xé correctement sur le

haut de la chambre de broyage (voir B2).

C. Assurez-vous que l’évier est propre. Enduisez la face

inférieure de l’ouverture à bourrelet du collet d’évier avec

du mastic de plomberie (voir C1). À partir du dessus de

l’évier, pressez le collet d’évier sur l’ouverture de celui-

ci aﬁ n d'e ectuer un bon joint d’étanchéité (C2). NE

BOUGEZ PAS OU NE TOURNEZ PAS le collet d’évier

une fois le joint d’étanchéité e ectué, le joint pourrait se

briser.

D. Placez un objet lourd, comme le broyeur (utiliser

une serviette pour éviter d’égratigner l'évier) sur le

dessus du collet d’évier pour le maintenir.

INSTALLATION (SUITE)

E. Prenez la portion restante de l'assemblage de

ﬁ xation que vous aviez placé de côté. Sous l’évier

insérez le joint d’étanchéité en ﬁ bre (voir E1), puis

la bague de montage (E2), et ensuite la bague de

montage supérieure (voir E3).

F. Maintenez les trois parties en place tout en ﬁ xant

l'anneau de retenue (voir F1) en l'écartant et en le

plaçant dans la rainure du collet d’évier (voir F2).

G. Serrez les trois vis de ﬁ xation fermement contre le collet

d’évier (voir G1). Évitez de trop visser.

H. Retirez l'excès de mastic à plomberie dans l’évier

avec un couteau en plastique ou un outil similaire qui

n’endommagera pas votre évier.

INSTALLATION (SUITE)

Vous avez un problème? Ne le retournez pas au magasin.

Appelez-nous sans frais au 1-833-240-6224 pour de l’assistance.

L-V 8:00am-5:00pm PST Anglais et Espagnol

Page is loading ...

Frigidaire 5304503339 User guide

Related papers

Other documents