Samsung LW32A23W User manual

BN68-00448D-02

English-2

Caution

CAUTION:

TO PREVENT ELECTRICAL SHOCK,

DO NOT REMOVE REAR COVER, NO USER

SERVICEABLE PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

The lightning flash and arrow head

within the triangle is a warning

sign alerting you of “dangerous

voltage” inside the product.

The exclamation point within the

triangle is a warning sign alerting

you of important instructions

accompanying the product.

WARNING:TO PREVENT DAMAGE WHICH MAY RESULT IN FIRE OR SHOCK HAZARD, DO NOT EXPOSE

THIS APPLIANCE TO RAIN OR MOISTURE.

☛

The main voltage is indicated on the rear of your set and the frequency is 50 or 60 Hz.

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co., Ltd. is strictly forbidden.

Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or consequential damages in

connection with the furnishing, performance, or use of this material.

The

Samsung logo is the registered trademarks of Samsung Electronics Co., Ltd.; Microsoft, Windows

®

and Windows

®

NT are

registered trademark of Microsoft Corporation; VESA, DPMS and DDC are registered trademarks of Video Electronics Standard

Association. All other product names mentioned herein may be the trademarks or registered trademarks of their respective owners.

Plug and Play

The adoption of the new VESA

®

Plug and Play solution eliminates complicated and time consuming setup. It allows you to install

your set in a Plug and Play compatible system without the usual hassles and confusion. Your computer system can easily identify

and configure itself for use with your set. Your set automatically tells the computer system its Extended Display Identification Data

(EDID) using Display Data Channel (DDC) protocols so the computer system can automatically configure itself to use your set.

Power Saver

This set is EPA Energy Star

®

compliant and NUTEK compliant when used with a computer equipped with VESA DPMS

functionality. For energy conservation, turn your set Off when you are not using it or when leaving it unattended for long periods.

European Notice (Europe Only)

Products with the CE Marking comply with both the EMC Directive (89/336/EEC), (92/31/EEC), (93/68/EEC) and the Low

Voltage Directive (73/23/EEC) issued by the Commission of the European Community. Compliance with these directives

implies conformity to the following European Norms:

■ EN55022:1998+A1:2000 - Radio Frequency Interference

■ EN55024:1998 - Electromagnetic Immunity

■ EN55013:1990+A12:1994+A13:1996+A14:1999 - Radio Frequency Interference

■ EN55020:1994+A11:1996+A12/A13/A14:1999 - Electromagnetic Immunity

■ EN61000-3-2:1995+A1/A2:1998 - Power Line Harmonics

■ EN61000-3-3:1995 - Voltage Fluctuations

■ EN60065:1997 or EN60095:1998 - Product Safety

English-3

Safety Instructions

These illustrations represent precautions concerning your set.

THIS DEVICE IS NOT FOR USE IN INDUSTRIAL ENVIRONMENTS

5`

10%

H

35`

75%

Do NOT expose your set to extreme

temperature or humidity conditions.

Do NOT expose your set to

direct sunlight.

Do NOT expose your set to any liquids.

If your set is broken,

do not try to repair it yourself.

Contact qualified service personnel.

During storm conditions (especially when

there is lightning) unplug your set from

the mains socket and aerial.

Do not overload wall outlets or

extension cord. Possible fire hazard.

Always keep your set in a

well-ventilated area.

Do not step on or

twist the power cord.

Keep the power cord away from

any heat source. Possible fire hazard.

If the remote control is not used for a long

period of time, remove the batteries and

store it in a cool, dry place.

English-4

Contents

◆ FOREWORD

■

Caution ................................................................................................................ 2

■

Safety Instructions ................................................................................................ 3

◆ CONNECTING AND PREPARING YOUR TV

■

Viewing the Control Panel ................................................................................... 6

■

Viewing the Connection Panel............................................................................. 7

-

Connecting an Aerial or Cable Television Network .......................................... 7

-

Connecting Set-Top Box, VCR or DVD ............................................................ 7

-

Connecting External A/V Devices ..................................................................... 7

-

Connecting Component Devices (DTV/DVD)................................................... 8

-

Connecting Computer ...................................................................................... 8

-

Connecting Digital Audio Inputs ...................................................................... 8

-

Connecting 5.1 Channel Speakers For Home Theater....................................... 9

■

Viewing the Remote Control (All Functions Except Teletext)................................ 10

■

Viewing the Remote Control (Teletext Functions) ................................................ 11

■

Installing Batteries in the Remote Control ............................................................ 12

■

Switching On and Off.......................................................................................... 13

■

Placing Your Television in Standby Mode............................................................ 13

■

Becoming Familiar with the Remote Control........................................................ 14

■

Plug and Play....................................................................................................... 15

■

Choosing Your Language ..................................................................................... 16

◆ SETTING THE CHANNELS

■

Storing Channels Automatically ........................................................................... 17

■

Sorting the Stored Channels ................................................................................. 18

■

Storing Channels Manually .................................................................................. 19

■

Editing the Channels ............................................................................................ 21

■

Assigning Channels Names .................................................................................. 22

■

Fine Tuning Channel Reception........................................................................... 23

■

LNA (Low Noise Amplifier).................................................................................. 23

◆ SETTING THE PICTURE

■

Changing the Picture Standard............................................................................. 24

■

Adjusting the Custom Picture............................................................................... 24

■

Changing the Colour Tone................................................................................... 25

■

Changing the Picture Size .................................................................................... 25

■

Freezing the Current Picture................................................................................. 26

■

DNIe (Digital Natural Image engine).................................................................... 26

■

Viewing the Picture In Picture (PIP) ..................................................................... 27

◆ SETTING THE SOUND

■

Adjusting the Volume .......................................................................................... 29

■

Switching the Sound Off Temporarily .................................................................. 29

■

Changing the Sound Standard.............................................................................. 30

■

Adjusting the Sound Settings................................................................................ 30

■

Listening to the Sound of the Sub Picture............................................................. 31

English-5

Contents

◆ SETTING THE SOUND (cONTINUED)

■

Setting the Dolby Digital Surround ...................................................................... 32

■

Setting the Dolby Pro Logic II .............................................................................. 34

■

Setting the External Digital Sound ........................................................................ 35

■

Connecting Headphones...................................................................................... 36

■

Adjusting Your Headphone Preferences............................................................... 36

■

Selecting the Sound Mode ................................................................................... 37

◆ SETTING THE TIME

■

Setting and Displaying the Current Time.............................................................. 38

■

Setting the Sleep Timer ........................................................................................ 39

■

Switching the Television On and Off Automatically ............................................ 40

◆ SETTING THE OTHERS

■

Setting the Blue Screen Mode .............................................................................. 41

■

Selecting a Device from External Sources ............................................................ 42

■

Viewing Pictures from External Sources ............................................................... 42

◆ SETTING THE PC

■

Setting up Your PC Software (Based on Windows 2000 or XP) ............................ 43

■

Adjusting the PC Screen Automatically ................................................................ 44

■

Coarse and Fine Tuning of the Image................................................................... 45

■

Changing the Image Position ............................................................................... 46

■

Initializing the Image Settings............................................................................... 46

■

Selecting the DVI Mode....................................................................................... 47

◆ USING THE TELETEXT FEATURE

■

Teletext Decoder.................................................................................................. 48

■

Displaying the Teletext Information ..................................................................... 48

■

Selecting a Specific Teletext Page ........................................................................ 49

■

Using FLOF to Select a Teletext Page................................................................... 50

◆ RECOMMENDATIONS FOR USE

■

Troubleshooting: Before Contacting Service Personnel ........................................ 51

■

Installing Stand .................................................................................................... 52

■

Using the Anti-Theft Kensington Lock .................................................................. 53

■

How to Install the Wall Bracket ........................................................................... 54

■

Technical and Environmental Specifications ........................................................ 56

■

Display Mode (PC/DVI)........................................................................................ 57

■

Pin Configurations ............................................................................................... 58

■

Wiring the Mains Power Supply Plug (UK Only).................................................. 59

☛

➢

Press Important Note

Symbols

English-6

Viewing the Control Panel

(Power)

Press to turn the TV on and off.

Power Indicator

Lights up when you turn the power off.

Remote Control Sensor

Aim the remote control towards this spot

on the TV.

TV/VIDEO

Displays a menu of all of the available

input sources (TV, AV1, AV2, AV3,

S-VIDEO, COMP1, COMP2, PC/DVI).

MENU

Press to see an on-screen menu of

your TV’s features.

-

+

Press to increase or decrease the volume.

Also used to select items on the

on-screen menu.

C/P.

Press to change channels.

Also press to highlight various items

on the on-screen menu.

(Without the Remote Control, You can

turn on TV by using the Channel buttons.)

1 5

6

7

2

3

4

English-7

Viewing the Connection Panel

☛

Whenever you connect an audio or video system to your set, ensure that all elements are switched

off

.

Connecting an Aerial or Cable Television Network

To view television channels correctly, a signal must be received by the set from one of the following sources:

- An outdoor aerial

-Acable television network

-Asatellite network

Connecting Set-Top Box, VCR or DVD

- Connect the VCR or DVD SCART cable to the SCART connector of the VCR or DVD.

- If you wish to connect both the Set-Top Box and VCR (or DVD), you should connect the Set-Top Box

to the VCR (or DVD) and connect the VCR (or DVD) to your set.

➣

Input/Output Specification

Connecting External A/V Devices

- Connect RCA or S-VIDEO cable to an appropriate external A/V device such as VCR, DVD or Camcorder.

- Connect RCA audio cables to “

AUDIO(L)” and “AUDIO(R)” on the rear of your set and the other ends to

corresponding audio out connectors on the A/V device.

- Headphone may be connected to the headphone output ( ) on the rear of your set.

While the headphone

is connected, the sound from the built-in speakers will be disabled.

Power Input

1

2

3

4

Connector

SCART 1

SCART 2

Video Audio (L/R) S-Video RGB Video+Audio (L/R)

✔✔ ✔ Only TV Out

✔✔

Monitor Out

(TV/AV1/AV2/AV3/S-VHS)

Input Output

English-8

Viewing the Connection Panel

Connecting Component Devices (DTV/DVD)

- Connect component video cables to component connector (“Y”,“Pb”,“Pr”) on the rear of your set and the

other ends to corresponding component video out connectors on the DTV or DVD.

- If you wish to connect both the Set-Top Box and DTV (or DVD), you should connect the Set-Top Box to the

DTV (or DVD) and connect the DTV (or DVD) to component connector

(“Y”,“Pb”,“Pr”) on your set.

- The Y, Pb and Pr connectors on your component devices (DTV or DVD) are sometimes labeled Y, B-Y and

R-Y or Y, Cb and Cr.

- Connect RCA audio cables to “

AUDIO(L)” and “AUDIO(R)” on the rear of your set and the other ends to

corresponding audio out connectors on the DTV or DVD.

Connecting Computer

- Connect the DVI connector to the PC video connector.

- Connect the stereo audio cable to “

PC AUDIO IN (STEREO)” on the rear of your set and the other end to

“Audio Out” of the sound card on your computer.

Connecting Digital Audio Inputs

Connect optical digital audio cable or coaxial cable (RCA audio cable) to “DIGITAL AUDIO IN” on the rear of

your set and the other end to “DIGITAL OUT” of the equipment with a digital output to enjoy digital sound

(Multi-Channel Surround Sound, Stereo or Dolby Pro-Logic II).

Source Video Horizontal Frequency Vertical Frequency Resolution

(kHz) (Hz) (Lines)

TV/VIDEO PAL 15.625 50 575

SECAM 15.625 50 575

NTSC4.43 15.734 60 483

NTSC3.58 (Except RF) 15.704 60 483

Component 1/2 480/60i 15.734 60 483

480/60p 31.469 60 483

576/50i 15.625 50 576

576/50p 31.250 50 576

720/60p 45.000 60 720

1080/50i 28.125 50 1080

1080/60i 33.750 60 1080

5

6

7

English-9

Viewing the Connection Panel

Connecting 5.1 Channel Speakers For Home Theater

The other speakers

(Surround/Center/Sub

woofer):Connect the each

speaker audio cable to the

speaker output jack(surround

/Center / Woofer 1 )on the

rear of your set making sure

that the

+, - polarities are

correctly aligned.

➢

Wind the speaker cable on

the core twice or more.

8

10

12

11

Main Speaker : When the speakers are attached with LCD TV

Main Speaker : When the speakers are separated from LCD TV

Connect the speaker audio cables to the main

speaker output jacks on the rear of your set

making sure that the

+, - polarities are correctly

aligned.

➢

The speakers MUST have more than

10watts rating (Impedance 8Ω).

Mount the brackets on the speaker

and your set.

Connect the speaker and your set

using screws.

Surround

Speaker

Surround

Speaker

Woofer

Center Speaker

LCD TV Rear

Main Speaker Main Speaker

9

POWER

P.MODETV SELECT

PRE-CH

-/--

MUTE

P

VIDEO

TTX/MIX

INFO

EXIT

MENU

STILL

S.MODE

ENTER

DUAL I-II

SURROUND

BN59-00373

123

456

789

0

BN59-00373A

SET RESET

P.SIZE SLEEP PIP

DNIe PC

SWAP P

REW STOP

PLAY/PAUSE FF

English-10

Viewing the Remote Control (All Functions Except Teletext)

NUMERIC BUTTONS

ONE/TWO-DIGIT CHANNEL SELECTION

VOLUME INCREASE

(Refer to page 29)

SOUND STANDARD SELECTION

(Refer to page 30)

AUTOMATIC SWITCH-OFF

(Refer to page 39)

DNIe SELECTION

(Refer to page 26)

SET

PC MODE SELECTION

(Refer to page 44)

VCR/DVD FUNCTIONS;



:

REWIND



:

STOP



/

:

PLAY/PAUSE



:

FAST FORWARD

TEMPORARY SOUND SWITCH OFF

(Refer to page 29)

ON-SCREEN DISPLAY

(Refer to page 14)

STILL THE MAIN PICTURE

(Refer to page 26)

PICTURE STANDARD SELECTION

(Refer to page 24)

MAKE THE REMOTE CONTROL

WORKS FOR TV, VCR, CABLE,

DVD, STB

INFORMATION DISPLAY (CURRENT

CHANNEL AND AUDIO/VIDEO

SETTINGS)

(Refer to page 38)

PREVIOUS CHANNEL

NEXT CHANNEL

(Refer to page 14)

PREVIOUS CHANNEL

VIDEO INPUT SOURCE SELECTION

(Refer to page 42)

EXIT FROM THE OSD

CHANGE CONFIRMATION

CONTROL THE CURSOR IN THE MENU

(Refer to page 14)

DOLBY PRO-LOGIC II ON/OFF

SELECTION

(Refer to page 32~34)

SOUND MODE SELECTION

(Refer to page 37)

PIP FUNCTIONS; (Refer to page 27)

PIP ON

: PIP ON/OFF

P/ :PIP CHANNEL SELECTION

SWAP : INTERCHANGE THE MAIN

AND SUB PICTURE

➣

The performance of the remote control may be affected by bright light.

DISPLAY SELECTED INPUT SOURCE

AND BATTERY STATUS

VOLUME DECREASE

TELEVISION STANDBY BUTTON

(Refer to page 13)

TV MODE INFORMATION DISPLAY

PICTURE SIZE SELECTION

(Refer to page 25)

RESET

"

English-11

POWER

P.MODETV SELECT

PRE-CH

-/--

MUTE

P

VIDEO

TTX/MIX

INFO

EXIT

MENU

STILL

S.MODE

ENTER

DUAL I-II

SURROUND

BN59-00373

123

456

789

0

BN59-00373A

SET RESET

P.SIZE SLEEP PIP

DNIe PC

SWAP P

REW STOP

PLAY/PAUSE FF

Viewing the Remote Control (Teletext Functions)

TELETEXT HOLD

TELETEXT CANCEL

TELETEXT INDEX

TELETEXT REVEAL

TELETEXT NEXT PAGE

TELETEXT PREVIOUS PAGE

TELETEXT SUB-PAGE

TELETEXT SIZE SELECTION

TELETEXT DISPLAY/MIX

➣

Teletext Function : Refer to page 46-48 for details

English-12

Installing Batteries in the Remote Control

1 Side the cover out completely.

2 Install two AAA size batteries.

➣

Make

sure to match the “+” and “–” ends of the batteries with

the diagram inside the compartment.

3 Replace the cover.

➣

Remove the batteries and store them in a cool, dry place if you

won’t be using the remote control for a long time.

The remote control can be used up to about 23 feet from the TV.

(Assuming typical TV usage, the batteries last for about one

year.)

➣

The remote control doesn’t work!

Check the following:

1. Is the TV power switch on?

2. Is the selected source TV and not video, cable or DVD?

3. Are the plus end and the minus end of the battery reversed?

4. Did the battery run out?

5. Is there a power outage?

6. Is the power cord unplugged?

7. Is there a special fluorescent light or a neon sign nearby?

English-13

Switching On and Off

Placing Your Television in Standby Mode

P.MODETV SELECT

PRE-CH

-/--

MUTE

P

VIDEO

TTX/MIX

INFO

EXIT

MENU

123

456

789

0

POWER

P.MODETV SELECT

PRE-CH

-/--

MUTE

P

VIDEO

TTX/MIX

INFO

EXIT

MENU

123

456

789

0

Your set can be placed in Standby mode, in order to reduce the power

consumption. The Standby mode can be useful when you wish to

interrupt viewing temporarily (during a meal, for example).

1 Press the POWER () button on the remote control.

Result

:

The screen is turned off and a orange standby indicator

appears on the front of your set.

2 To switch your set back on, simply press the POWER ( ), numeric

buttons (

0~9) or channel up/down ( / ) button again.

➣

Do not leave your set in Standby mode for long periods of time

(when you are away on holiday, for example).

Turn your set off by pressing the POWER ( ) button on the front

of the set.

It is best to unplug the set from the mains and aerial.

➣

1. Use of the 'Power' button on the remote is possible only when the

TV is in 'Power Saving' (standby) mode. If the TV is powered off,

the remote cannot be used to turn the TV on.

2. To retain the time and or automatic alarm settings, always put the

TV in stand-by mode with the remote control.

Use of the the power switch on the TV will clear all time related

settings.

[Benefit] This full 'power off' function is as effective as unplugging

the power cable.

TV switches to standby mode when powered off by the remote

control. To return power ( ) to the screen, press the remote

control 'ON' or channel button( ). Pressing the power button on

the TV does not return power to the screen because in this case,

the TV restores the last mode, which was 'Power Saving'.

The mains lead is attached to the rear of your set.

☛

If you have purchased this set in the United Kingdom,

refer to page 59 for further instructions on plug wiring.

1 Plug the mains lead into an appropriate socket.

Result

:

The main voltage is indicated on the rear of your set and

the frequency is 50 or 60Hz.

2 Press the POWER () button on the front of your set.

Result

:

The standby indicator lights up on the front panel.

3 Press the POWER ( ), numeric button (0~9) or channel

up/down( / ) button on the remote control or power or

C/P.

button on the front of your set.

Result:

The programme that you were watching last is reselected

automatically.

➣

When you switch the set on for the very first time, you will be

asked to choose language in which the menus are to be

displayed (see page 15).

4 To switch your set off, press the POWER () again.

English-14

Becoming Familiar with the Remote Control

The remote control is used mainly to:

◆

Change channels and adjust the volume

◆

Set up your set using the on-screen menu system

The following table presents the most frequently used buttons and

their functions.

Button Viewing Function Menu Function

Used to display the

-

next stored channel.

Used to display the

-

previous stored channel.

to Used to display the corresponding channels.

➣

For double digit channels, the second digit

must be pushed immediately after the first.

Failure to do this will result in a single digit

channel being displayed.

_

/

__

Used to select a channel numbered ten or over.

Press this button, and enter the two digit channel

number.

Used to increase the

-

volume.

Used to decrease the

-

volume.

MUTE Used to switch the sound off temporarily.

➣

To turn the sound back on, press this button

again, or press the

+

/

-

button.

MENU

Used to display the Used to return to the

on-screen menu system. previous menu or

normal viewing.

EXIT

Used to exit the On-Screen menu system.

-

Used to:

◆ Display a submenu

containing selections

for the current menu

option.

◆ Search forwards/

backwards manually

for channels

◆ Increase/decrease a

menu option value.

-

Used to confirm your

ENTER

choice.

POWER

P.MODETV SELECT

PRE-CH

-/--

MUTE

P

VIDEO

TTX/MIX

INFO

EXIT

MENU

STILL

S.MODE

ENTER

DUAL I-II

SURROUND

BN59-00373

123

456

789

0

English-15

Plug and Play

When the set is initially powered ON, several basic customer settings

proceed automatically and subsequently.

The following settings are available.

1 If the set is in standby mode, press the POWER () button on the

remote control.

Result

:

The message

Plug & Play

is displayed. It appears for a

little while, and then the

Language

menu is automatically

displayed.

2 Select the appropriate Language by pressing the or  button.

➣

The available languages are listed

.

You can choose one of 18 Languages.

3 Press the

ENTER

or  button to confirm your choice.

Result

:

The message Ant. Input Check is displayed with the OK

is selected.

4 Press the

ENTER

or  button.

Result

:

The following countries are available:

Belgie

-

Deutschland

-

Espania

-

France

-

Italia

-

Nederland

-

Schweiz

-

Sverige

-

UK

-

East Europe

-

Others

5 Select your Country by pressing the or  button.

Press the

ENTER

or  button.

Result

:

The channel search will start and end automatically.

6 Select the Hour or Min by pressing the ¦or  button.

Set the

Hour/Min by pressing the or  button.

(

Refer to “Switching the television on and off automatically” on page 40

)

7 Press the

ENTER

button to confirm your setting.

Result

:

The

message Enjoy Your Watching is displayed, and

then the channel which has been stored will be activated.

POWER

P.MODETV SELECT

English-16

Plug and Play

If you want to reset this feature...

1 Press the MENU button.

Result

:

The main menu is displayed.

2 Press the or  button to select Setup.

Press the

ENTER

or  button

.

Result:

The options available in the

Setup

group are displayed.

3 Press the  or  button to select Plug & Play

.

4 Press the

ENTER

button

.

Result:

The message is

Plug & Play

displayed.

5 For further details on how to set, refer to the previous page.

Choosing Your Language

When you start using your set for the first time, you must select the

language which will be used for displaying menus and indications.

1 Press the MENU button.

Result

:

The main menu is displayed.

2 Press the or  button to select Setup.

Result

:

The options available in the

Setup

group are displayed.

3 Press the

ENTER

or  button

.

4 Press the  or  button

to

select Language

.

Press the

ENTER

or  button

.

Result:

The available

languages

are listed.

5 Select a particular language by pressing the or button

repeatedly.

Press the

ENTER

or  button

.

➣

You can choose one of 18 Languages.

6 When you are satisfied with your choice, press the EXIT button to

return to normal viewing.



TTX/MIX

INFO

EXIT

MENU

STILL

S.MODE

ENTER

DUAL I-II

SURROUND

BN59-00373

TTX/MIX

INFO

EXIT

MENU

STILL

S.MODE

ENTER

DUAL I-II

SURROUND

BN59-00373

English-17

Storing Channels Automatically

You can scan for the frequency ranges available to you (and

availability depends on your country). Automatically allocated

programme numbers may not correspond to actual or desired

programme numbers. However you can sort numbers manually and

clear any channels you do not wish to watch.

1 Press the MENU button.

Result

:

The main menu is displayed.

2 Press the or button to select Channel.

Result

:

The options available in the

Channel

group are displayed.

3 Press the

ENTER

or  button

.

Result:

The

Country

is selected.

4 Press the

ENTER

or  button again

. Select your

Country

by

pressing the

or 

button repeatedly.

The following countries are available:

Belgie

-

Deutschland

-

Espania

-

France

-

Italia

-

Nederland

-

Schweiz

-

Sverige

-

UK

-

East Europe

-

Others

5 Press the

ENTER

button

.

6 Press the button to select ATM.

Press the

ENTER

or  button

.

Result:

The Start is selected.

7 Press

ENTER

button to search the channels.

The sub menu is changed from Start to Stop with channel search

started.

Result:

The search will end automatically. Channels are sorted

and stored in an order which reflects their position in the

frequency range, (with lowest first and highest last).

The programme originally selected is then displayed.

➣

To return to the previous menu, press

¦ or  button to select

Return and then press

ENTER

button

.

➣

To stop the search before it has finished, press

ENTER

button with stop selected.

8 When the channels have been stored, you can:

◆ Sort them in the order required (refer to page 18)

◆ Assign a name to the stored channels (refer to page 22)

◆ Add or delete the channels (refer to page 21)

◆ Fine tune channel reception if necessary (refer to page 23)

◆ Activate the LNA (Low Noise Amplifier) feature (refer to page 23)

TTX/MIX

INFO

EXIT

MENU

STILL

S.MODE

ENTER

DUAL I-II

SURROUND

BN59-00373

English-18

Sorting the Stored Channels

You can exchange the numbers of two channels, in order to:

◆

Modify the numeric order in which the channels have been

automatically stored.

◆

Give easily remembered numbers to the channels that you

watch most often.

1 Press the MENU button.

Result

:

The main menu is displayed.

2 Press the or  button to select Channel.

Press the

ENTER

or  button

.

Result:

The options available in the

Channel

group are displayed.

3 Press the or  button to select Sort

.

Press the

ENTER

or  button.

Result

: The

Prog. Channel and Name are

displayed.

4 Select the Channel number that you wish to change by pressing the

or  button repeatedly.

Press the

ENTER

or  button

.

Result

: The selected

Channel number and Name

is moved to

right side.

5 Press the or  button to move to the position which you would

like to change and then press the

ENTER

button.

Result

:

The selected channel is exchanged with the one

previously stored to the chosen number.

6 Repeat step 4 to 5 for another channel to sort again.

TTX/MIX

INFO

EXIT

MENU

STILL

S.MODE

ENTER

DUAL I-II

SURROUND

BN59-00373

English-19

Storing Channels Manually

You can store up to 100 channels, including those received via cable

networks. When storing channels manually, you can choose:

◆

Whether or not to store each of the channels found

◆

The programme number of each stored channel which you

wish to identify

1 Press the MENU button.

Result

:

The main menu is displayed.

2 Press the or  button to select Channel.

Result

:

The options available in the

Channel

group are displayed.

3 Press the

ENTER

or  button

.

4 Press the or  button

to

select Manual Store

.

Press the

ENTER

or  button.

Result

: The options available in the Manual Store menu are

displayed with

Prog.No selected.

5 Press the

ENTER

button again.

To assign a programme number to a channel, find the correct

number by pressing the

or  button and then press the

ENTER

button

.

6 Press the or  button to select Colour System and then press

the

ENTER

or  button.

Select the

Colour System required by pressing the or  button

repeatedly and then press the

ENTER

or  button.

Result

: The colour standards are displayed in the following order:

AUTO

-

PAL

-

SECAM

-

NT4.43

7 Press the or  button to select Sound System and then press the

ENTER

or  button.

Select the sound standard required by pressing the

or  button

repeatedly and then press the

ENTER

or  button.

Result

: The sound standards are displayed in the following order:

BG

-

DK

-

I

-

L

8 For all the channels to move to the required channel numbers,

repeat steps 5 to 7 after selecting Prog.No by pressing or 

button

.

English-20

Storing Channels Manually (continued)

9 If you know the number of the channel to be stored....

◆ Press the or  button to select Channel and then press the

ENTER

or  button.

◆ Select C (Air channel) or S (Cable channel) by pressing the

or  button and then press the

ENTER

or button.

◆ Select the required number by pressing the or  button and

then press the

ENTER

or  button.

➣

If there is abnormal sound or no sound, re-select the sound

system required.

10 If you do not know the channel numbers, press the or  button to

select

Search and then press the

ENTER

or button.

Search by pressing or  button and then press the

ENTER

or

 button.

Result

: The tuner scans the frequency range until the first

channel or the channel that you selected is received on

your screen.

11 Press the  or  button to select Store and then press the

ENTER

or  button.

Select

Yes by pressing the or  button and then press the

ENTER

button.

Result

: The channel and associated programme number are

stored.

12 Repeat Steps 9 to11 for each channel to be stored.

☛

CChhaannnneell mmooddee

◆

PP

(Programme mode): When tuning is completed, the

broadcasting stations in your area will have been

assigned to position numbers from P00 to P99. You can

select a channel by entering the position number in this

mode.

◆

CC

(Real channel mode): You can select a channel by

entering the assigned number to each broadcast station in

this mode.

◆

SS

(Cable channel mode): You can select a channel by

entering the assigned number to each cable channel in

this mode.

Page is loading ...

Samsung LW32A23W User manual

This manual is also suitable for

Samsung LW32A23W User manual

Related papers

Other documents