Makita EK7650H User manual
- Category
- Power universal cutters
- Type
- User manual
This manual is also suitable for
Instruction Manual
EK7650H
EK7651H
Important:
Read this instruction manual carefully before putting the Power Cutter into operation and strictly observe the safety
regulations!
Keep this instruction manual!
2
Thank you for purchasing a MAKITA
product!
Congratulations on choosing a MAKITA Power Cutter! We are
condent that you will be satised with this modern piece of
equipment.
We want you to be satised with your MAKITA product.
In order to guarantee the optimal function and performance of your
Power Cutter and to ensure your personal safety we would request
you to perform the following:
Read this instruction manual carefully before putting the Power
Cutter into operation for the rst time, and strictly observe the
safety regulations! Failure to observe these precautions can
lead to severe injury or death!
English
Table of Contents Page
Delivery inventory .......................................................................... 3
Symbols...........................................................................................3
SAFETY PRECAUTIONS ................................................................4
General precautions ...................................................................4
Protective equipment .................................................................4
Fuels / Refuelling .......................................................................5
Putting into operation .................................................................5
Cutoff discs ................................................................................6
Kickback and lock-in ..................................................................7
Working behavior / Method of working .......................................7
Cutting metals ............................................................................8
Cutting masonry and concrete ...................................................8
Transport and storage ................................................................9
Maintenance .............................................................................10
First aid ....................................................................................10
Technical data ............................................................................... 11
Denomination of components .....................................................12
PUTTING INTO OPERATION ........................................................13
Mounting the cutting disc ......................................................... 13
Tightening the V-belt / Checking V-belt tension .......................14
Before operating .......................................................................14
Operating .......................................................................................16
Starting .....................................................................................16
Adjusting the carburetor ..............................................................17
MAINTENANCE .............................................................................17
V-belt .......................................................................................18
Cleaning the protection hood ................................................... 18
Cleaning/changing the air lter .................................................19
Spark plug maintenance ..........................................................20
Replacing the suction head ......................................................20
Cleaning the starter ..................................................................21
Changing the cutting attachment position (central/side) .......... 22
SPECIAL ACCESSORIES .............................................................23
Diamond cutting discs ..............................................................23
Guide trolley .............................................................................23
Water tank (the component of trolley) ...................................... 23
Mains/pressure water system ..................................................23
Maintenance chart ........................................................................24
Fault location ................................................................................ 24
Troubleshooting ...........................................................................25
Storage .......................................................................................... 26
3
You will notice the following symbols on the saw and in the Instruction Manual:
Symbols
Read instruction manual and follow the
warning and safety precautions!
WARNING: the max. peripheral
speed of the cutting disc is 80 m/s!
Particular care and caution! Cutting disc dimensions
Forbidden! Engine-Manual start
Wear protective helmet, eye and ear
protection, and respiratory protection!
Stop engine!
Wear protective gloves! Warning! Kickback!
No smoking! Fuel (Gasoline)
No open re! First Aid
Direction of cutting wheel rotation
Delivery inventory
In case one of the parts listed should not be included in the
delivery inventory, please consult your sales agent.
1
2345
1. Power Cutter
2. 13/19 AF combination wrench
3. Star-shaped wrench
4. Carburetor adjustment screwdriver
5. Adapter ring (Tools for some countries may not require this
ring.)
6. Instruction manual (not shown)
4
General precautions
The operator MUST read this instruction manual to ensure safe operation -
(even if you already have experience in using cutoff saws). It is important
to be familiar with the operation of this particular cutoff saw. Users insufciently
informed will endanger themselves as well as others due to improper handling.
Let only persons who have experience in using cutoff saws work with this unit. -
When letting another person use the Power Cutter, this instruction manual must
be provided along with it.
First-time operators should ask a specialist to instruct them in working with -
gasoline-powered cutoff saws.
Children and persons under 18 years of age must not be allowed to use this -
Power Cutter. Persons over the age of 16 years may, however, use the Power
Cutter for the purpose of being trained as long as they are under the supervision
of a qualied trainer.
Working with the Power Cutter requires high concentration. -
Operate the Power Cutter only if you are in good physical condition. If you are -
tired, your attention will be reduced. Be especially careful at the end of a working
day. Perform all work calmly and carefully. The user has to accept liability for
others.
Never work while under the inuence of alcohol, drugs, medication or other -
substances which may impair vision, dexterity or judgement.
A re extinguisher must be available in the immediate vicinity. -
Asbestos and other materials that can release toxins may be cut only with the -
necessary safety precautions and after notication of the proper authorities and
under their supervision or that of a person appointed by them.
Protective equipment
In order to avoid head, eye, hand or foot injuries as well as to protect your -
hearing the following protective equipment must be used during operation
of the Power Cutter:
The kind of clothing should be appropriate, i. e. it should be tight-tting but not -
be a hindrance. Clothing in which grains of material can accumulate (trousers
with cuffs, jackets and trousers with wide-open pockets, etc.) must not be worn,
particularly when cutting metal.
Do not wear any jewellery or clothing that can get caught or distract from the -
operation of the Power Cutter.
It is necessary to wear a protective helmet whenever working with the Power -
Cutter. The protective helmet (A) is to be checked in regular intervals for
damage and is to be replaced after 5 years at the latest. Use only approved
protective helmets.
The helmet - visor (B) protects the face from dust and material grains. In order to
prevent injuries to eyes and face, always wear protective goggles (C) or visor
when using the Power Cutter.
To prevent hearing damage, always wear suitable personal - hearing protection
(ear muffs (D), ear plugs, etc.). Octave brand analysis upon request.
When dry-cutting dust-producing materials such as stone or concrete, always -
wear approved respiratory protection (E).
Work gloves - (F) of tough leather are part of the required work kit of the Power
Cutter and must always be worn when working with the Power Cutter.
SAFETY PRECAUTIONS
EF
1
2
3
4
5
Always wear - safety shoes or boots (G) with steel toes, non-skid soles, and leg
protectors when working with the Power Cutter. Safety shoes equipped with a
protective layer provide protection against cuts and ensure a secure footing.
Always wear a - work suit (H) of sturdy material.
Fuels / Refuelling
Go to a safe, level place before refuelling. - Never refuel while on scaffolding,
on heaps of material, or in similar places!
Switch off the engine before refuelling the Power Cutter. -
Do not smoke or work near open res (6). -
Let the engine cool down before refuelling. -
Fuels can contain substances similar to solvents. Eyes and skin should not come -
in contact with mineral oil products. Always wear protective gloves when refuelling
(not the regular work gloves!). Frequently clean and change protective clothes.
Do not breathe in fuel vapors. Inhalation of fuel vapours can be hazardous to your
health.
Do not spill fuel. If a spill occurs, clean off the Power Cutter immediately. Fuel -
should not come in contact with clothes. If your clothes have come in contact with
fuel, change them at once.
Ensure that no fuel oozes into the soil (environmental protection). Use an -
appropriate base.
Refuelling is not allowed in closed rooms. Fuel vapors will accumulate near the -
oor (explosion hazard).
Ensure to rmly tighten the screw cap of the fuel tank. -
Before starting the engine, move to a location at least 3 meters -
(approx. 3 1/4 yards) from where you fuelled the Power Cutter (7), but not within
the extended swing range of the cutting disc (direction of sparks).
Fuel cannot be stored for an unlimited period of time. Buy only as much as will be -
consumed in the near future.
Use only approved and marked containers for the transport and storage of fuel. -
Keep fuel away from children! -
Putting into operation
Do not work on your own. There must be someone around in case of an -
emergency (within shouting distance).
Observe all anti-noise regulations when working in residential areas. -
Never use the Power Cutter near inammable materials or explosive gases! -
The Power Cutter can create sparks leading to re or explosion!
Make sure that all persons within 30 meters (33 yards), such as other workers, -
are wearing protective gear (see “Protective equipment”) (8). Children and other
unauthorized persons must remain more than 30 meters away from the working
area. Keep an eye out for animals as well (9).
Before starting work the Power Cutter must be checked for perfect function -
and operating safety according to the prescriptions.
In particular, make sure that the cutting wheel is in good condition (replace
immediately if torn, damaged or bent), the cutting wheel is properly mounted, the
protection hood is locked in place, the hand guard is properly mounted, the V-belt
has the proper tension, the throttle moves easily and the grips are clean and dry,
and the combination switch functions properly.
Start the Power Cutter only after complete assembly and inspection. Never use -
the Power Cutter when it is not completely assembled.
5
6
7
8
9
3 meters
= wearing Protective Equipment
30 m
6
Cutoff discs
The protection hood must always be on! Change discs only with the engine -
off!
There are two basic types of cutoff discs: -
For metal (hot cutting) -
For masonry (cold cutting) -
NOTE:
When using diamond cutoff discs, always make sure to observe the “direction of
rotation” markings. Diamond discs should only be used for cutting masonry/brick/
concrete etc.
Cutoff discs are intended only for radial loading, i.e. for cutting. -
Do not grind with the sides of the cutting disc! This will break the disc (10)!
CAUTION:
Never change direction (turning radius less than 5 meters / 5 1/2 yards), exert
lateral (sideways) pressure, or tip the Power Cutter during cutting (11)!
Use a cutting disc only for cutting the materials it is intended for. The proper type -
of disc must be used, for either metals or masonry.
The arbour hole (bore) of the cutting disc must t the shaft exactly. If the arbour -
hole is larger than the shaft diameter, a spacer ring must be used (accessories).
Use only cutting wheels approved by the DSA (German Abrasive Disc -
Committee) or equivalent organisation for freehand cutting at up to 4,370 RPM
(= 80 m/sec. at circumference) for 14”/355 mm discs, or up to 5,100 RPM
(= 80 m/sec. at circumference) for 12”/300 mm discs.
The disc must be free of defects (12). Do not use defective cutting discs. -
Always tighten the cutting disc mounting bolt to a torque of 30 Nm.
Otherwise, the cutting disc can twist.
Before starting the cutting disc, make sure you have a steady footing. -
Put the Power Cutter into operation only as described in this instruction manual -
(13). Always place your left foot in the rear handle and grasp the other handle
rmly (with thumb and ngers). Other starting methods are not allowed.
When starting the Power Cutter it must be well supported and securely held. The -
cutting disc must not be touching anything.
If the cutting disc is new, test it by running it at least 60 seconds at top speed. -
When doing this, make sure that no persons or body parts are in the extended
swing range of the disc, in case it is defective and ies apart.
When working with the Power Cutter always hold it with both hands. - Take
the back handle with the right hand and the tubular handle with the left hand.
Hold the handles tightly with your thumbs facing your ngers.
CAUTION: When you release the throttle lever the disc will keep spinning -
for a short period of time (free-wheeling effect).
Continuously ensure that you have a safe footing. -
Hold the Power Cutter such that you will not breathe in the exhaust gas. Do not -
work in closed rooms or in deep holes or ditches (danger of poisoning by fumes).
Switch off the Power Cutter immediately if you observe any changes in its -
operating behavior.
Switch off the engine before inspecting the V-belt tension or tightening it, -
replacing the cutting wheel, repositioning the cutter attachment (side or
middle position) or eliminating faults (14).
Turn off the engine immediately and check the disc if you hear or feel any change -
in cutting behaviour.
Turn off the Power Cutter when taking a break or stopping work (14). Place the -
unit in such a way that the disc is not touching anything and cannot endanger
anyone.
Do not put the overheated Power Cutter in dry grass or on any inammable -
objects. The mufer is very hot (danger of re).
IMPORTANT: - After wet cutting, rst turn off the water feed and then let the disc
run at least 30 seconds, to ing off the remaining water and prevent corrosion.
10
11
12
13
14
min. 5 m
Maintenance•
Refuelling•
Changing cutoff discs•
Repositioning the •
cutting attachment
Stopping work•
Transport•
Putting out of •
function
7
Kickback and lock-in
When working with the Power Cutter there is a danger of kickback and lock-in. -
Kickback occurs when the top of the cutting disc is used for cutting (15). -
This causes the Power Cutter to be thrown back toward the user with great force -
and out of control. Risk of injury!
To prevent kickback, observe the following:
Never cut with the section of the cutting disc shown in gure 15. -
Be especially careful when reinserting the disc into cuts that have already
been started!
Lock-in occurs when the cut narrows (crack, or workpiece under stress). -
This causes the Power Cutter to suddenly jump forward, out of control and with -
great force. Risk of injury!
To prevent lock-in, observe the following:
When reinserting the disc into previous cuts, have the Power Cutter running at -
top speed. Always cut at top speed.
Always support the workpiece so that the cut is under tension (16), so that the -
cut does not press together and jam the cutting disc as it proceeds through the
material.
When starting a cut, apply the disc to the workpiece with care. -
Do not just shove it into the material.
Never cut more than one piece at a time! When cutting, make sure that no other -
workpiece comes into contact.
Working behavior / Method of working
Before starting work, check the work area for any hazards (electrical wires, -
inammable substances). Clearly mark the work area (for example with warning
signs or by cordoning off the area).
When working with the Power Cutter hold it rmly by the front and rear handles. -
Never leave the Power Cutter unattended!
Whenever possible run the Power Cutter at the rated arbour speed (see -
“Technical data”).
Only use the Power Cutter during good light and visibility periods. -
Be aware of slippery or wet areas, and of ice and snow (risk of slipping).
Never work on unstable surfaces. Make sure that there are no obstacles in the -
working area, risk of stumbling. Always ensure that you have a safe footing.
Never cut above your shoulder height (17). -
Never stand on a ladder to cut (17). -
Never use the Power Cutter while standing on scaffolding. -
Do not lean over too far when working. When putting down and picking up the -
Power Cutter, do not bend over from the waist, but instead bend in the knees.
Save your back!
Guide the Power Cutter in such a way that no part of your body is within the -
extended swing range of the disc (18).
Use cutting discs only for the materials for which they are designed! -
Do not use the Power Cutter to lift up and shovel away pieces of material and -
other objects.
Important! Before cutting, remove all foreign objects, such as rocks, gravel, nails
etc. from the cutting area. Otherwise, such objects can be ung away by the disc
with great speed. Injury hazard!
When cutting workpieces down to length use a rm support. If necessary, secure -
the workpiece from slipping, but do not steady it with your foot or allow another
person to hold it.
When cutting round items, always secure them against rotation. -
When guiding the Power Cutter by hand, use the side mounting position of the -
cutter attachment only when actually necessary.
Otherwise, always use the central position. This gives the unit a better balance,
for reduced operator fatigue.
15
16
17
18
8
Cutting metals
IMPORTANT!
Always wear approved respiratory protection!
Materials that can release toxic substances may be cut only after notifying the
proper authorities and under their supervision or that of a person appointed
by them.
CAUTION:
The rapid rotation of the cutting disc heats metal and melts it at the point of
contact. Swing the guard as far down as possible behind the cut (19) in order
to direct the stream of sparks forward, away from the operator (re hazard).
Determine the direction of cutting, mark the cut and apply the disc to the material -
at moderate speed, to cut a guide groove before going to top speed and applying
more pressure to the Power Cutter.
Keep the disc straight and vertical. Do not tip it, as this can break it. -
The best way to get a good, clean cut is to pull or move the Power Cutter back -
and forth. Do not simply press the disc into the material.
Thick round stock is best cut in stages (20). -
Thin tubing and pipes can be cut with a simple downward cut. -
Cut large-diameter pipes as for round stock. To prevent tipping and for better -
control, do not let the disc sink too deeply into the material. Instead, always cut
shallow around the whole piece.
Worn discs have a smaller diameter than new discs, so that at the same engine -
speed they have a lower effective circumferential speed and therefore do not cut
as well.
Cut I-beams and L-bars in steps; see Figure 21. -
Cut bands and plates like pipes: along the wide side with a long cut. -
When cutting material under stress (supported material or material in structures), -
always make a notch in the thrust (pressure) side, and then cut from the tension
side, so that the disc does not lock in. Secure cutoff material from falling!
CAUTION:
If there is a chance that the material is under stress, be prepared for it to kick
back. Make sure you can get out of the way if you have to!
Be particularly careful in scrap-metal yards, junkyards, at accident sites,
and with haphazard piles of material. Precariously balanced pieces or pieces
under stress can act in unpredictable ways, and may slide, jump out, or burst.
Secure cutoff material from falling! Always exercise extreme caution and use
only equipment that is in perfect working order.
Observe the accident-prevention rules and regulations of your employer and/
or insurance organization.
Cutting masonry and concrete
IMPORTANT!
Always wear approved respiratory protection!
Asbestos and other materials that can release toxic substances may be cut
only after notifying the proper authorities and under their supervision or that
of a person appointed by them. When cutting prestressed and reinforced
concrete piles, follow the instructions and standards of the responsible
authorities or the builder of the structural member. Reinforcement rods must
be cut in the prescribed sequence and in accordance with applicable safety
regulations.
NOTE:
Mortar, stone, and concrete develop large quantities of dust during cutting. To
increase the lifetime of the cutting disc (by cooling), to improve visibility, and to
avoid excessive dust creation, we strongly recommend wet cutting instead of dry
cutting.
19
20
21
9
In wet cutting, the disc is wetted at an equal rate on both sides by a trickle of
water. MAKITA offers the right accessories for all wet cutting applications (see also
“SPECIAL ACCESSORIES”).
Remove foreign objects such as sand, stones and nails found within the working -
area. CAUTION: Watch out for electric wires and cables!
The rapid rotation of the cutting disc at the point of contact throws fragments
out of the cut groove at high speed. For your safety, swing the protection
hood down as far as possible behind the cut (23), so that material fragments
are thrown forward, away from the operator.
Mark the cut, and then make a groove about 5 mm (just under 1/5”) along the -
entire length of the planned cut. This groove will then guide the Power Cutter
accurately guring the actual cutoff.
NOTE:
For long, straight cuts we recommend using a trolley (24, see also “SPECIAL
ACCESSORIES”). This makes it much easier to guide the unit straight.
Perform the cut with a steady back-and-forth motion. -
When cutting slabs to size, you need not cut through the entire material thickness -
(creating unnecessary dust). Instead, simply make a shallow groove, and then
knock off the excess material cleanly on a at surface (25).
CAREFUL!
When cutting into lengths, cutting through material, making cutouts, etc., always
make sure to plan the direction and sequence of cuts in such a way that the disc
does not get jammed by the cut-off piece, and that no persons can be injured by
falling pieces.
Transport and storage
Always turn off the Power Cutter when transporting it or moving it from -
place to place on a site (26).
Never carry or move the unit with the engine on or the disc moving! -
Carry the unit only by the tubular (middle) handle with the cutting disc pointing -
behind you (26). Avoid touching the exhaust mufer (burn hazard!)
When moving the Power Cutter over longer distances, use a wheelbarrow or -
wagon.
When transporting the Power Cutter in a vehicle, make sure it is securely -
positioned in such a way that no fuel can leak out.
Always remove the cutting disc before transporting the unit in a vehicle.
The Power Cutter should be stored safely in a dry place. It must not be left -
outdoors! Always dismount the cutting disc before storage. Keep the Power
Cutter away from children.
Before long-term storage and before shipping the Power Cutter, follow the -
instructions in the chapter on “Storage”. ALWAYS empty the fuel tank and
run the carburetor dry.
When putting cutting discs in storage, be careful to: -
Clean and dry them well. -
Store them lying down at. -
Avoid dampness, freezing temperatures, direct sunshine, high temperatures and -
temperature uctuations, as these can cause breakage and splintering.
Always check new cutting discs or cutting discs that have been in storage -
to make sure that they are free of defects.
23
24
25
26
10
Maintenance
Before performing maintenance work switch off the Power Cutter - (27) and
pull out the plug cap.
Always check the Power Cutter before using it to make sure that it is in good -
working order. In particular, make sure that the cutting disc is properly mounted.
Make sure that the cutting wheel is undamaged and suitable for the job it will be
used for.
Operate the Power Cutter only at a low noise and emission level. -
For this ensure the carburetor is adjusted correctly.
Clean the Power Cutter regularly. -
Check the fuel tank cap regularly for good sealing. -
Observe the accident prevention instructions issued by trade associations
and insurance companies. NEVER make any modications to the Power
Cutter! You will only be putting your own safety at risk!
Perform only the maintenance and repair works described in the instruction
manual. All other work must be carried out by MAKITA Service (28).
Use only original MAKITA spares and accessories.
The use of non-MAKITA spares, accessories, or cutting discs increases the risk of
accident. We cannot accept any responsibility for accidents or damage occurring
in association with the use of cutting discs or accessories other than original
MAKITA.
27
28
29
SERVICE
First aid (29)
Make sure that a rst aid kit is always immediately available close by. Immediately
replace any items used from the rst aid box.
When calling for help, give the following information:
Place of the accident -
What happened -
Number of injured people -
Kind of injuries -
Your name! -
NOTE:
Individuals with poor circulation who are exposed to excessive vibration may
experience injury to blood vessels or the nervous system.
Vibration may cause the following symptoms to occur in the ngers, hands or wrists:
“Falling asleep” (numbness), tingling, pain, stabbing sensation, alteration of skin
colour or of the skin.
If any of these symptoms occur, see a physician!
11
Technical data
Model
Item
EK7650H EK7651H
Engine Displacement cm
3
75.6
Bore mm 51
Stroke mm 37
Max. power kW 3.0
Max. torque Nm 4.6
Idling speed min
-1
2,600
Clutch Auto centrifugal system
Engine speed limitation min
-1
9,100
Max. spindle speed min
-1
4,300
Carburetor Diaphragm type
Ignition system (with speed limitation) Non-contact, magnet type
Spark plug Type NGK CMR6H
Electrode gap mm 0.5
Starting system Recoil system
Fuel consumption at max. load per
ISO 8893
kg/h 1.2
Specic consumption at max. load per
ISO 8893
g/kWh 400
Fuel Automobile gasoline (petrol)
Fuel tank capacity l 1.1
Lubricant (engine oil) API grade SF class or higher SAE 10W-30 oil (automobile 4-stroke engine oil)
Lubricant quantity l 0.22
Cutting disc for 80 m/sec. or higher
1)
(DSA approved):
dimensions
mm 300 / 20 / 5
2)
300 / 25.4 / 5
2)
350 / 20 / 5
2)
350 / 25.4 / 5
2)
Arbor diameter mm 20.0 25.4 20.0 25.4
Spindle diameter mm 17 17 or 25.4
3)
Minimum ange outside diameter mm 102
Max. cutting depth mm 97 122
Power Cutter Dimensions (overall length x overall
width x overall height)
761 mm x 310 mm x 435 mm 780 mm x 310 mm x 455 mm
V-belt no. no. 225094-6
Overall weight (tanks empty, without cutting disc) kg 12.7 12.9
1) Circumference speed at max. engine speed
2) Outside diameter / arbor hole / thickness
3) Country specic
12
Denomination of components
1. Rear handle
2. Filter cover
3. Lock screw
4. Top cover for air lter and spark plug cap
5. Top cover
6. Front handle
7. Protection hood
8. Tensioning screw
9. Hex. nut
10. Mufer
11. Starter grip
12. Oil tank cap
13. Fuel tank cap
14. Fuel pump (Primmer)
15. Cutting disc
16. Outer ange
17. Hex bolt
18. Switch
19. Safety locking button
20. Throttle lever
1
2
3
4
5
7
8
9
10
11
12
13
14
15
16
17
18
19
20
6
13
PUTTING INTO OPERATION
CAUTION:
Always turn off the engine and pull off the spark plug cap
before doing any work on the Power Cutter! Always wear
protective gloves!
CAUTION:
Start the Power Cutter only after complete assembly and
inspection.
Mounting the cutting disc
WARNING:
When installing a diamond cutting disc, be sure to mount •
it so that the arrow is in the same direction as the outer
ange (6) rotates. Mounting the diamond cutting disc (4) with
its arrow direction opposite to that on the wheel cover may
cause chipping of the disc edge and personal injury.
When installing a cutting disc (4), always use the ring that •
matches the bore of the cutting disc and the diameter of
the spindle (5). Failure to use rings that mate may cause tool
vibration resulting in serious personal injury.
Only use cutting discs with the bore that matches the •
diameter of the ring(s) provided. Using discs that do not mate
may cause tool vibration resulting in serious personal injury.
Inspect a cutting disc for damage. (see the section titled •
“Cutoff discs” in SAFETY PRECAUTIONS.)
1. Insert the star-shaped wrench (2) into the hole (8) to prevent
the spindle (5) from rotating.
NOTE: When the holder of the pressure water system is installed
in the hole in the tool, remove it before mounting the
cutting disc.
2. While holding on the wrench (2) in that position, use the
combination wrench (1) provided and turn the bolt (7) securing
the disc counterclockwise and remove the bolt (7) and outer
ange (6).
3. Mount a diamond cutting disc/cut-off abrasive disc (4) on the
arbor (5). And then put the outer ange (6) on the spindle
so that the two parallel at surface on the outer ange t the
spindle at surface and rmly tighten the bolt clockwise.
To install a cutting disc, mount a ring with the same matching
diameter as the disc bore and the O ring provided to retain the
ring on the spindle before installing a diamond cutting disc.
And then install the cutting disc.
NOTE: Tighten the hex bolt rmly (25 - 31 Nm), as otherwise the
cutting wheel may slip during cutting.
4
5
6
7
6
1
8
2
Schematic
drawing
For the following work, use the assembly tools included with
delivery:
1. 13/16 AF combination wrench
2. Star-sharped wrench
3. Carburetor adjustment screwdriver
4. Adapter ring
Place the Power Cutter on a stable surface and carry out the
following assembly steps:
No air lter is installed!
Before operation, squeeze the supplied lter several times so
that oil is evenly immersed in the entire lter. Insert an oiled
foam lter (pre-lter), as shown in the adjacent illustration! To
do this, take off the lter cover (see the chapter on Cleaning/
changing the air lter).
14
Tightening the V-belt / Checking V-belt tension
IMPORTANT:
Exact V-belt tension is essential for maximum cutting
performance with minimum fuel consumption. Improper
V-belt tension will result in premature wear to the V-belt and
V-belt wheel or damage to the clutch bearing.
NOTE: The two hex. nut (9) must be loosened before tightening
the V-belt or checking the tension.
To increase the belt tension, turn the tension screw (10) to the
right (clockwise) with the combination wrench included with the
Power Cutter.
The belt tension is correctly adjusted when the nut (11) is located
as shown in the gure compared to the position of the mark (12).
IMPORTANT:
After tightening/inspection, make certain to tighten •
the hex. nut (9) (25 - 31 Nm).
Do not adjust the belt tension while the machine is •
hot. There is a risk of burn injury.
11
12
9
10
Before operating
1. Checking/replenishing engine oil
With the engine in a cool state, check/replenish engine oil in •
the following way.
Position engine on a at level, and check to see whether oil is •
within the range of MAX and MIN of the oil tank.
If oil is insufcient (near the MIN mark of the oil tank), ll the •
oil tank with oil to the MAX mark.
Oil quantity can be checked externally without removing the oil •
cap as the oil level can be seen at the external, see-through,
measuring mark window.
For reference, oil needs to be replenished every ten operating •
hours (one tank of oil for ten fuel refuels).
Replace extremely dirty or discolored oil. •
<Recommended oil> .... Use API grade SF class or higher SAE
10W-30 oil (automobile 4-stroke engine
oil).
<Oil quantity> ...............0.22 L (220 mL)
NOTE:
If the engine is not stored in the upright position, oil will •
circulate through the engine, which will mean that there will be
excessive oil in the Power Cutter when replenishing.
If oil exceeds the MAX mark, it may leak out causing dirtying •
or white smoke.
Oil replacement Point 1 <Oil cap>
Interval of replacement: Initially, after 20 operating hours, and
subsequently every 30 operating hours.
Clean away the dirt from around oil lling neck and then •
remove oil cap.
Place the oil cap on a surface where it will not pick up grit and •
dirt. If the cap is put back on in a dirty state, oil circulation may
deteriorate and engine parts become worn, which may cause
mechanical failure.
MAX mark
MIN mark
Oil
The oil is visible from here, so
the MAX and MIN marks can
be used to check the quantity
of oil.
15
(1) Place engine on the level and remove oil cap.
(2) Replenish oil to the base of the oil lling neck.
When replenishing oil, use a proper lubricant container for
relling.
(3) Firmly tighten oil cap. If oil cap is loose, oil may leak out.
Oil replacement Point 2 <What to do if oil is spilled>
If oil is spilt between fuel tank and engine, and the Power Cutter
operated, oil will be sucked in via the cold air intake, which may
cause dirtying. Always wipe off spilt oil before using the power
cutter.
2. Refueling
WARNING:
Always observe the following items when refueling. •
Failure to do so may cause ames or re.
Refuel away from ames. In addition, never smoke or •
bring any form of ame near to fuel or power cutter during
refueling.
Stop the engine and let it cool down before refueling.•
Always open fuel tank cap slowly to release internal •
pressure in a controlled manner. Failure to do so may cause
fuel to spray out because of internal pressure.
Be careful not to spill fuel. If fuel is spilt, fully wipe away •
fuel.
Refuel in a well-ventilated location.•
Always handle fuel with full care.•
If fuel comes into contact with skin and/or eyes, it may •
cause an allergic reaction and/or inammation.
In cases of such allergic reactions and/or inammation, etc.,
seek medical advice from a specialist doctor immediately.
<Fuel storage period>
As a rule, fuel held in a proper fuel container, in a shaded
location, with good ventilation, should be used up within four
weeks. If a proper fuel container is not used and/or the cap is left
off, etc., and the season is summer, fuel may deteriorate in one
day.
Storing the Power Cutter and fuel container
Store Power Cutter and fuel container away from direct •
sunlight in a cool location.
Do not leave fuelled up Power Cutter or fuel container in •
automobile or automobile trunk (boot).
<Fuel>
The engine is a four-stroke engine, so use automobile gasoline
(regular gasoline/petrol) to run the engine.
Fuel points
Do not use a gasoline mixture (engine oil mixed with •
gasoline). Doing so may cause carbon build up and
mechanical failure.
The use of old fuel may cause poor engine startup.•
<Refueling>
Always stop the engine and let it cool down before refueling.
<Usable Gasoline>
.....
Automobile gasoline (petrol)
Slightly loosen the fuel tank cap to release pressure and thus •
equalize external and internal air pressure.
Remove fuel tank cap and refuel. (Do not ll to the top of the •
tank neck.)
After refueling, rmly tighten on fuel tank cap.•
The fuel tank cap is a consumable product. Therefore, if it •
shows wear or other abnormalities, replace it. (Rough guide to
replacement is once every two or three years.)
Oil tank cap
Fuel tank cap
Fuel tank
Fuel MAX
Level
16
Operating
Starting
WARNING:
Do not start the engine in locations where refueling has
taken place. Move at least three meters away from the place
where the Power Cutter was fuelled.
Failure to do so may cause ames or re.•
CAUTION:
Before starting engine, be sure to check that the cutting
disc is not touching the ground or any other obstacle.
If the cutting disc is touching the ground or other obstacle, it •
may cause an accident.
As soon as the engine starts, the cutting disc will rotate, so
be fully aware of nearby people and obstacles.
1. Cold-starting
(1) Repeatedly press primer pump until fuel enters it.
(2) Flip switch in direction of
(choke).
(3) Hold down rear handle with a foot and rmly hold down
tubular handle with a hand.
(4) Vigorously pull the start handle repeatedly until the rst ring
up sound is heard.
Warming up
Once engine starts, hold down safety lever, and squeeze and •
release throttle repeatedly for one or two minutes to warm up
the engine.
Once engine speed stabilizes and it revs smoothly from low to •
high speed, warming up is complete.
2. Starting up when engine is warm
Press the primer pump several times. From the outset, place the
switch in the [I] (operating) position, and start the engine using
task (3) of procedure 1 above.
NOTE:
Repeatedly pulling and releasing the starter grip with the •
switch set to choke will ood the engine with fuel, making start
up difcult.
When the engine stops, never squeeze the throttle lever.•
Unnecessarily squeezing the throttle lever with the engine
stopping will ood the engine with fuel, making start up
difcult.
If the engine does become ooded with fuel, remove the •
spark plug, and slowly pull the starter handle several times to
remove the excess fuel. Also, dry the electrode section of the
spark plug.
Do not pull starter handle to the limit of the rope, as doing so •
shortens the lifespan of the rope. Furthermore, gently return
the starter handle without suddenly letting go of it.
Avoid letting the Power Cutter run at maximum idling speed, •
as doing so will shorten the lifespan of the engine.
3. Stopping
To stop the engine, release the throttle, and set the switch to the
(Stop) position.
If the choke lever is wrongly moved to the position to stop the
tool, use half throttle to restart.
Throttle lever
Starter grip
Switch
Switch
Safety locking
button
17
NOTE: This engine is equipped with an electronic ignition
to limit the speed. The carburetor also has a xed jet which
cannot be adjusted.
At the factory the idling speed has been set to
approx. 2,600 min
-1
, but the running-in process of a new
engine may require slight readjustment of the idling speed.
Set the idling speed with a screwdriver (width of blade: 4 mm).
A screwdriver with a molded-on lug, supplied as an optional
accessory, is useful for the adjustment.
4. Idling adjustment
CAUTION: Carburetor adjustment may only be done by a
specialist MAKITA service center!
Do not undertake any adjustments to adjusting screws (H)
and (L) without a tachometer! Incorrect adjustment can lead
to engine damage!
A tachometer is needed for adjustments to adjusting screws
(H) and (L), because if the engine runs over its maximum
rated speed, it can overheat and run out of lubricant. This
can damage the engine!
Only adjusting screw (T) can be manipulated by the user. If
the cutting disc moves in idle (i.e. without the throttle being
pressed), it is imperative to correct the idle speed!
Idle speed adjustment must only be undertaken when the
engine is warm, with a clean air lter.
Use a screwdriver (4 mm blade) for idle adjustments.
Adjusting the carburetor
Adjusting screw
MAINTENANCE
CAUTION:
Before doing any work on the Power Cutter • stop the
engine and let it cool down, remove the cutting disc,
pull the plug cap off the spark plug and wear protective
gloves!
Carrying out maintenance directly after stopping the engine or
with the plug cap on the spark plug may cause burns from hot
engine or injury from inadvertent start up.
Start the Power Cutter only after complete assembly and •
inspection.
Never use gasoline, benzine, thinner, alcohol or the like. •
Discoloration, deformation or cracks may result.
NOTE:
Wipe off dirt from the Power Cutter and then select a clean •
workplace to carry out maintenance.
18
V-belt
1. Adjusting V-belt tension
If the cutting disc halts in mid operation easily, the V-belt •
has slackened. If this is the case, adjust tension using the
following procedure.
(1) Loosen belt cover tightening nuts.
(2) Turn the tension adjustment screw to the right (clockwise)
until the indicator nut reaches the marked position in order to
increase the tension of the V-belt.
(3) Once V-belt tensioning is complete, rmly retighten the belt
cover tightening nuts.
If the cutting disc stops easily even though the tension of the •
V-belt has been adjusted, or the V-belt breaks, replace with a
new V-belt.
2. Changing the V-belt
(1) Loosen tightening nut, and turn tension adjustment screw to
the left until the end of the screw is visible.
(2) Remove tightening nuts, and then remove belt cover.
(3) Next, remove the three mounting screws, and remove the
clutch cover.
(4) Remove the old V-belt, and t on a new V-belt. Now,
remount the clutch cover followed by belt cover.
(5) Adjust tension as shown in the Adjusting V-belt tension
section.
Cleaning the protection hood
Over time, the inside of the protection hood can become caked
with material residue (especially from wet cutting), which if
allowed to accumulate can hinder the free rotation of the cutting
disc. For this reason the hood must be cleaned out from time to
time.
Take off the cutting wheel and remove the accumulated material
from inside the hood with a strip of wood or similar implement.
Clean the shaft and all disassembled parts with a cloth.
NOTE: To install the cutting wheel see “Mounting the cutting
disc”.
Tensioning screw
Tensioning screw
Indication nut
Mark
Hex. nut
Hex. nut
Belt cover
Belt cover
End of screw
Clutch cover
IMPORTANT:
Because many of the parts and assemblies not mentioned
in this Instruction Manual are vital to the safety of the unit,
and because all parts are subject to a certain amount of wear
and tear, it is important for your own safety that you have the
unit checked and maintained regularly by a MAKITA service
center.
IMPORTANT:
If the cutting wheel breaks during cutting, the
Power Cutter must be repaired by a MAKITA
service centre before being used again!
SERVICE
19
Cleaning/changing the air lter
If the air lter becomes clogged, it may cause poor engine •
performance. Therefore, every time after using the Power
Cutter, be sure to clean the air lter in the following way.
Turn the cover lock to the left and remove it.•
Remove the top cover after blowing off dust from it.•
Next, remove the prelter.•
Remove the four star-shaped screws.•
Remove the lter cover.•
Remove the air lter.•
Remove the dust bag lter from the lter cover and gently tap •
and blow on it to clean.
Gently tap and blow on the inner lter to remove dirt and dust. •
Also, periodically wash the inner lter in soapy water and dry
thoroughly.
To clean the air lter tap it gently. If an air compressor is to be •
used, blow the compressed air onto the inside of the air lter.
Do not wash the air lter.
Blow off dust from around the lters.•
Reassemble the air lter to lter cover once cleaning is •
nished.
Tighten the cover lock rmly.•
Cover lock
Loosen
Top cover
Top cover
Prelter
Star-shaped
screws
Filter cover
Star-shaped
screws
Dust bag lter
Air lter
Inner lter
20
Spark plug maintenance
(1) Loosen the cover lock and remove the top cover.
(2) Open plug cover, remove plug cap, and remove spark plug.
(3) Check to see whether or not the electrode gap is 0.5 mm. If
the gap is too big or too small, adjust it to 0.5 mm.
(4) If carbon and/or dirt has gathered on spark plug, clean,
and then remount. An excessively worn or burnt spark plug
should be replaced with a new one.
(5) After carrying out maintenance on the spark plug, remount it,
attach plug cap, and then secure plug cover.
Top cover
Cover lock
0.5 mm
Replacing the suction head
The fuel tank lter (13) of the suction head can become clogged.
It is recommended to replace the suction head once every three
months in order to ensure unimpeded fuel ow to the carburetor.
Unscrew the fuel tank cap (12) and pull the loss-prevention
stopper out.
Empty fuel tank.
To remove the suction head for replacement, pull it out through
the tank ller neck using a piece of wire bent at one end to form
a hook.
CAUTION: Do not allow fuel to come into contact with skin!
12
13
Plug cap
Loosen
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
Makita EK7650H User manual
- Category
- Power universal cutters
- Type
- User manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Makita EE2650H User manual
-
Makita DPC8131 User manual
-
-
Makita EK7651H User manual
-
Makita DPC8111 User manual
-
Makita EK7650H User manual
-
-
-
-
Makita EK7301-B-69646 User manual