Contents
Caution 4
Features 6
Controls, Indicators and Connections 7
Menu Organization & Adjustment 12
Menu Contents 13
Optional Accessories 25
.............................................................................................
...........................................................................................
....................................................
..........................................................
..................................................................................
..........................................................................
FCC (Federal Communications Commission)
This equipment has been tested and found to comply with the limits for class A digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interface when the equipment
is operated in a commercial environment.
This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment
in a residential to correct the interference at his own expense
CAUTION: Change or modications not expressly approved by the manufacturer responsible for compliance could
void the user’s authority to operate the equipment.
Disposal of Old Electrical & Electronic Equipment
(Applicable in the European Union and other European countries with separate collection systems)
This symbol on the product or on its packing indicates that this product shall not be treated as household waste.
Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic
equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequence
for the environment and human health, which could otherwise be caused by inappropriate waste handling of this
product. The recycling of materials will help to conserve natural resources.
Multi Format LCD Monitor 4
Multi Format LCD Monitor 4
Caution
◦ Power Requirements
- AC 100 ~ 240V
- DC 12V/24V
◦ All operating instructions must be read and understood before the product is operated.
◦ These safety and operating instructions must be kept in safe place for future reference.
◦ Do not use attachments not recommended by the manufacturer. Use of inadequate attachments
can result in accidents.
◦ This product must be operated on a power source specied on the specication label.
If you are not sure of the type of power supply used in your location, consult your dealer or local
power company.
◦ The power cords must be routed properly to prevent stepping on them or objects from resting on
them. Check the cords at the plugs and product.
◦ Do not overload AC outlets or extension cords. Overloading can cause re or electric shock.
◦ Never insert an object into the product through vents or openings. High voltage ows in the
product and inserting an object can cause electric shock and/or short internal parts.
For the same reason, do not spill water or liquid on the product.
◦ Do not attempt to service the product yourself. Removing covers can expose you to high voltage
and other dangerous conditions. Utilize a qualied electronics service specialist for all repairs.
◦ If any of the following conditions occurs, unplug the power cord from the AC outlet and request a
qualied service person to perform repairs.
a. When the power cord or plug in damaged.
b. When a liquid was spilled on the product or when objects have fallen into the product.
c. When the product has been exposed to rain or water.
d. When the product does not operate properly as described in the operating instructions.
Do not touch the controls other than those described in the operating instructions.
Improper adjustment of controls not described in the instructions can cause damage,
which often requires extensive adjustment work by a qualied technician.
e. When the product has been dropped or damaged.
f . When the product displays an abnormal condition. Any noticeable abnormality
in the product indicates that the product needs servicing.
Multi Format LCD Monitor 5
◦ In case the product needs service, consult an authorized TVLogic Reseller.
◦ Unplug the power cord from the AC outlet before cleaning the product. Use a damp cloth to clean
the product. Do not use liquid cleaners or aerosol cleaners.
◦ Keep the product away from direct Sun light.
◦ Do not place the product on an unstable cart, stand, tripod or table. Placing the product on an
unstable base can cause the product to fall, resulting in serious personal injuries as well as damage
to the product. Use only a cart, stand, tripod, bracket or table recommended by the manufacturer
or sold with the product. When mounting the product on a wall, be sure to follow the manufacturer's
instruction. Use only the mounting hardware recommended by the manufacturer.
◦ The vents and other openings in the cabinet are designed for ventilation. Do not cover or block
these vents and openings since insucient ventilation can cause overheating and/or shorten the
life of the product. Do not place the product in an enclosed place such as a bookcase or rack, unless
proper ventilation is provided or the manufacturer's instructions are followed.
◦ The LCD panel used in this product is made of glass. Therefore, it can break when the product is
dropped or exposed to impact.
◦ Keep the product away from heat sources such as radiators, heaters, stoves and other
heat generating products (including ampliers).
Caution
Multi Format LCD Monitor 6
Multi Format LCD Monitor 6
Features
LQM-071W/LQM-171W MONITORS CONTAIN THE FOLLOWING FEATURES AND ADVANTAGES :
◦ 4 x SDI Inputs.
◦ 4 x Analog CVBS Inputs.
◦ HD-SDI, SD-SDI, CVBS Auto-detecting.
◦ 1 x SD/HD SDI Output.
◦ Embedded Audio Level Meter.
◦ Built in audio disembedder and internal speakers.
◦ Stereo audio out using mini jacks.
◦ External audio in for line and speaker out.
◦ Wide Variety of Markers & Safety Areas.
◦ The monitor can be powered by a 12V DC power source.
◦ Remote control function using RS232 or RS422.
◦ User programmable function keys (F1, F2).
Multi Format LCD Monitor 7
<LQM-171W-FRONT>
1. Buttons
◦ Press any button to bring up the OSD display as shown in picture 4. The selected item will display
in red. The OSD display disappears after 5 seconds if no other control is made.
◦ Each button OSD indicates feature, channel and value.
◦ For features with a channel selection, press the button repeatedly to change and select the desired
channel. Select ALL to change all channels with the same value.
◦ For the button features with individual value selections, press the button repeatedly to increase
the value of the feature by 1. The value goes back to minimum after reaching the maximum value.
◦ Rotate the SELECT ENC knob to change the value of selected item. The value will automatically
will be stored in the memory (EEPROM) once the OSD disappears.
<LQM-071W Button OSD>
Controls, Indicators and Connections
LQM-071W : FRONT
FACTORY PGM
RS 232
SDI OUT
ETHERNET
USB
SDI1/CVBS1 INPUT
SDI2/CVBS2 INPUT
SDI3/CVBS3 INPUT
SDI4/CVBS4 INPUT
AUDIO OUTPUTREMOTE
GPI
RS 422
IN/OUT
DC 12V
INPUT
AC
INPUT
LEFT
SPEAKER
POWER CONFIG LED
STATUS LED
USB LED CH SEL SDI OUT UP F1
TALLY
ETHERNET LED MARKER MENU
SELECT
/BRIGHT
ENCODER
CHROMA
ENCODER
DISPLAY MODE VOLUME DN/F2
CONTRAST
ENCODER
MENU
ENCODER
PEAKING WAVE INTENSITY ENTER RIGHT
SPEAKER
AUDIO INPUT
D P M O D E
4 P
C H S E L
C H 1
PEAKING
C H 1
5
M A R K E R
C H 1
O FF
V O L U M E
1 2
SDI OUT
CH1
Multi Format LCD Monitor 8
Multi Format LCD Monitor 8
Controls, Indicators and Connections
2. BUTTON FUNCTION
◦ [DISPLAY MODE] Used to select display mode. (See Chart 2.)
◦ [CH SEL] Used to select active input channel.
◦ [PEAKING] Used to control the sharpness of the selected input display.
◦ [MARKER] Used to select Marker On/O of the selected input channel.
◦ [VOLUME] Used to control the volume.
◦ [SDI OUT] Used to select the SDI output source.
◦ [WAVE INTENSITY] Used to control the intensity of waveform and vector scope display.
◦ [MENU] Used to pop-up MENU OSD.
◦ [UP/F1] [DN/F2] Are used to navigate the menu, which works same way as the MENU ENC.
It is also used to activate the user’s selected feature when the MENU OSD is not active. (See chart 4.)
◦ [ENTER] Used to conrm a chosen value in the MENU, which works the same way as pressing
the MENU ENC button.
Multi Format LCD Monitor 9
Controls, Indicators and Connections
3. LED INDICATOR
◦ [USB] Indicates the connectivity between USB Port and PC. The LED will start to blink when
transmitting data with the PC to indicate the current status.
◦ [ETHERNET] Indicates the connectivity between Ethernet Port and Network. The LED will start to
blink when transmitting packets with PC to indicate the current status.
◦ [STAT] Indicates the current status of the Monitor. (Not supported under rmware V1.2)
◦ [CFG] LED turns on when the Monitor is updating its rmware. If the LED is on, do not turn o
the power of the monitor.
4. SELECT / BRIGHT ENCODER
◦ Rotate : Used to adjust the value of the selected feature and brightness.
◦ Press : Used to control the brightness of selected display.
5. CONTRAST ENCODER
◦ Rotate: Used to adjust the value of the contrast.
◦ Press: Used to control the contrast of selected display.
6. CHROMA ENCODER
◦ Rotate: Used to adjust the value of the saturation.
◦ Press: Used to control the saturation of selected display.
7. MENU ENCODER
◦ Rotate: Used to navigate the menu or to control the value of the selected feature.
◦ Press: Used to move to the next menu or to conrm a chosen value. Also, Press and hold for
1 second to return to the previous menu.
8. TALLY
◦ By using the remote, the tally light can be used for each input channel in either red or green.
At the same time, the selected channel’s image displays the Red/Green tally graphic.
Multi Format LCD Monitor 10
Multi Format LCD Monitor 10
Controls, Indicators and Connections
LQM-171W : REAR
FACTORY PGM
RS 232
SDI OUT
ETHERNET
USB
SDI1/CVBS1 INPUT
SDI2/CVBS2 INPUT
SDI3/CVBS3 INPUT
SDI4/CVBS4 INPUT
AUDIO OUTPUTREMOTE
GPI
RS 422
IN/OUT
DC 12V
INPUT
AC
INPUT
LEFT
SPEAKER
POWER CONFIG LED
STATUS LED
USB LED CH SEL SDI OUT UP F1
TALLY
ETHERNET LED MARKER MENU
SELECT
/BRIGHT
ENCODER
CHROMA
ENCODER
DISPLAY MODE VOLUME DN/F2
CONTRAST
ENCODER
MENU
ENCODER
PEAKING WAVE INTENSITY ENTER RIGHT
SPEAKER
AUDIO INPUT
<LQM-171W-REAR>
Multi Format LCD Monitor 11
1. SDI IN/OUT
◦ [SDI/CVBS INPUT] HD-SDI. SD-SDI, CVBS Signal input terminal.
◦ LQM-171W detects the input source automatically and displays the source format for SDI and
“NTSC” or “PAL” for CVBS HD-SDI.
◦ [SDI OUTPUT] SDI output terminal.
If the selected input channel is in HD-SDI, the output is in HD-SDI and if the selected input
channel is in SD-SDI input channel, the output is in SD-SDI. However, for analog input channels,
it is A/D converted for SD-SDI output.
2. AUDIO IN/OUT
◦ [AUDIO INPUT] Audio input terminal.
◦ [AUDIO OUTPUT] Audio output terminal for audio input or embedded audio in SDI.
◦ [SPEAKER] Audio output speaker for audio input or embedded audio in SDI.
3. DC IN
◦ DC 12V power input.
4. REMOTE
◦ Provides connection to monitor control equipment via simple GPI contact closure.
<Remote Connector Pin>
5. COMMUNICATION
◦ [RS232] LQM-171 can communicate through RS232 with other equipment. It is also used for
rmware updates.
◦ [RS422] LQM-171 can communicate through RS422 with other equipment. It is also used for
Dynamic UMD communication.
◦ [Ethernet] LQM-171 can communicate through Ethernet with other equipment. It is also used for
rmware updates.
◦ [USB] LQM-171 can communicate through USB 2.0 with other equipment. It is also used for
rmware updates.
Controls, Indicators and Connections
REM
O
TE (
R
J
-45
)
1:
P
in1
2
:
P
in2
3:
P
i
n
3
4:
P
in4
5: P
i
n5
6:
P
i
n
6
7:
P
in7
8
:
G
ND
1
8
Multi Format LCD Monitor 12
Multi Format LCD Monitor 12
Menu Organization & Adjustment
The product may be controlled and set system-wise through OSD displayed on the screen.
1) Menu Organization
Below is the organization of the product’s menu.
<Menu OSD>
- User can control the features of the monitor using the Menu.
- To control the Menu, use MENU button, MENU ENCODER and MENU ENC SW.
* MENU Button : ROOT Menu POP-UP, Return to previous Menu, Cancel value change (Undo).
* MENU ENCODER : Navigate the Menu, Change the value.
* MENU ENC SW : Select the Menu.
- Press and hold for 1 second to activate Menu.
- To conrm and activate the change made in the Menu, press the MENU ENC SW. If Menu button
is pressed after any change was made in the Menu, the change will not be stored and will return
to the previous value.
P IC T U R E
C O LO R
M A R K E R
R E M O T E
D IS P L A Y
SYSTEM
BRIG HT C H 1 0
CO NTRAST C H 1 0
CHRO M A C H 1 0
PEAKING C H 1 0
ASPECT RATIO C H 1 4:3
INT PATTERN OFF
C H 1 0
C H 2 0
C H 3 0
C H 4 0
A LL 0
Multi Format LCD Monitor 13
Menu Contents
[1] PICTURE
Below is the description for each function of the PICTURE menu.
1. BRIGHT
- Application: For each input channel.
- Value Range: -50 ~ 49
- Default Value: 0
- Function v: Controls the brightness of the selected input display.
2. CONTRAST
- Application: For each input channel.
- Value Range: -50 ~ 49
- Default Value: 0
- Function: Controls the contrast of the selected input display.
3. CHROMA
- Application: For each input channel.
- Value Range: -50 ~ 49
- Default Value: 0
- Function: Controls the saturation of the selected input display.
4. PEAKING
- Application: For each input channel.
- Value Range: 0 ~ 19
- Default Value: 0
- Function: Controls the sharpness of the selected input display.
5. ASPECT RATIO
- Application: For each input channel.
- Value Range: “4:3”, “16:9”
- Default Value: “4:3”
- Function: If selected input is in SD, input displays in 4:3 or 16:9 aspect ratio.
6. INT PATTERN
- Application: For all available inputs.
- Value Range : “OFF”, “WHT100%”, “WHT85%”, “WHT50%”, “WHT25%”, “GRN100%”, “GRN85%”, “GRN50%”,
“GRN25%”, “BLU100%”, “BLU85%”, “BLU50%”, “BLU25%”, “RED100%”, “RED85%”, “RED50%” , “RED25%”
- Default Value: “OFF”
- Function: Displays at image pattern used for such as color calibration.
Multi Format LCD Monitor 14
Multi Format LCD Monitor 14
Below is the description for each function of the COLOR menu.
1. COLOR TEMP
- Application: For all available inputs.
- Value Range: “3200K”, “5000K”, “5600K”, “6500K”, “9300K”, “CUSTOM1”, “CUSTOM2”, “CUSTOM3”
- Default Value: “6500K”
- Function: Controls Color Temperature of display.
Selected color temperature applies for all input channels.
2. GAIN RED
- Application: For all available inputs.
- Value Range: -50 ~ 49
- Default Value: Color calibration Value (No default value for custom1/2/3)
- Function: Controls gain value of Red.
3. GAIN GREEN
- Application: For all available inputs.
- Value Range: -50 ~ 49
- Default Value: Color calibration Value (No default value for custom1/2/3)
- Function: Controls gain value of Green.
4. GAIN BLUE
- Application: For all available inputs.
- Value Range: -50 ~ 49
- Default Value: Color calibration Value (No default value for custom1/2/3)
- Function: Controls gain value of Blue.
5) BIAS RED
- Application: For all available inputs.
- Value Range: -50 ~ 49
- Default Value: 0 (No default value for custom1/2/3)
- Function: Adjusts black level to control Red.
6. BIAS GREEN
- Application: For all available inputs.
- Value Range: -50 ~ 49
- Default Value: 0 (No default value for custom1/2/3)
- Function: Adjusts black level to control Green.
7. BIAS BLUE
- Application: For all available inputs.
- Value Range: -50 ~ 49
- Default Value: 0 (No default value for custom1/2/3)
- Function: Adjusts black level to control Blue.
[2] COLOR
Menu Contents
Multi Format LCD Monitor 15
Menu Contents
Below is the description for each function of the MARKER menu.
1. MARKER DISPLAY
- Application: For each input channel.
- Value Range: “OFF”, “ON”
- Default Value: “OFF”
- Function: Displays Marker for selected channel.
2. MARKER TYPE
- Application: For each input channel.
- Value Range: “4:3”, “16:9”, “15:9”, “14:9”, “13:9”, 1.85:1”, 2.35:1”, “USER”
- Default Value: “4:3”
- Function: Selects the Marker Type for selected channel. “4:3” marker only displays in HD display
while “16:9” marker only displays in SD display.
3. CENTER MARKER
- Application: For each input channel.
- Value Range: “OFF” , “ON”
- Default Value: “OFF”
- Function: Displays the Center Marker for selected channel.
4. SAFETY AREA
- Application: For each input channel.
- Value Range: “OFF”, “80%”, “88%”, “90%”, “93%”, “98%”, “USER”
- Default Value: “OFF”
- Function: Selects the Safety Area Marker type for selected channel.
5. FIT MARKER
- Application: For each input channel.
- Value Range: “NO” , “YES”
- Default Value: “NO”
- Function: Activates the Fit Marker function. With Fit Marker On, the Safety Area is displayed
relative to the Marker in use.
6. MARKER COLOR
- Application: For each input channel.
- Value Range: “WHITE”, “GRAY”, “BLACK”, “RED”, “GREEN”, “BLUE”
- Default Range: “WHITE”
- Function: Controls the color of the Marker for selected channel.
[3] MARKER
Multi Format LCD Monitor 16
Multi Format LCD Monitor 16
Menu Contents
7. USER MARKER H
- Application: For all available inputs.
- Value Range: 0 ~ 99
- Default Value: 99
- Function: Controls the position of user dened Horizontal Marker lines.
8. USER MARKER V
- Application: For all available inputs.
- Value Range: 0 ~ 99
- Default Value: 99
- Function: Controls the position of user dened Vertical Marker lines.
9. USER SAFETY AREA H
- Application: For all available inputs.
- Value Range: 0 ~ 99
- Default Value: 99
- Function: Controls the horizontal position of user dened Safety Area.
10. USER SAFETY AREA V
- Application: For all available inputs.
- Value Range: 0 ~ 99
- Default Value: 99
- Function: Controls the vertical position of user dened Safety Area.
Multi Format LCD Monitor 17
Below is the description for each function of the GPI menu.
1. PIN1
- Application: For all available inputs.
- Value Range: See Chart 1.
- Default Value: “R TLY C1”
- Function: Selects function for REMOTE PIN1.
2. PIN2
- Application: For all available inputs
- Value Range: See Chart 1.
- Default Value: “R TLY C2”
- Function: Selects function for REMOTE PIN2
3. PIN3
- Application: For all available inputs.
- Value Range: See Chart 1.
- Default Value: “R TLY C3”
- Function: Selects function for REMOTE PIN3.
4. PIN4
- Application: For all available inputs.
- Value Range: See Chart 1.
- Default Value: “R TLY C4”
- Function: Selects function for REMOTE PIN4.
Menu Contents
[4] REMOTE
Display Function
NONE No REMOTE function assigned.
R TLY C1 RED TALLY ON for CH1.
R TLY C2 RED TALLY ON for CH2.
R TLY C3 RED TALLY ON for CH3.
R TLY C4 RED TALLY ON for CH4.
G TLY C1 GREEN TALLY ON for CH1.
G TLY C2 GREEN TALLY ON for CH2.
G TLY C3 GREEN TALLY ON for CH3.
G TLY C4 GREEN TALLY ON for CH4.
MARK C1 MARKER DISPLAY ON for CH1.
MARK C2 MARKER DISPLAY ON for CH2.
MARK C3 MARKER DISPLAY ON for CH3.
MARK C4 MARKER DISPLAY ON for CH4.
PWR STBY LCD Monitor Power ON.
ACT SEL DISPLAY ACTIVE CH Select.
Multi Format LCD Monitor 18
Multi Format LCD Monitor 18
Menu Contents
5. PIN5
- Application: For all available inputs.
- Value Range: See Chart 1.
- Default Value: “G TLY C4”
- Function: Selects function for REMOTE PIN5.
6. PIN6
- Application: For all available inputs
- Value Range: See Chart 1.
- Default Value: “ACT SEL”
- Function: Selects function for REMOTE PIN6.
7. PIN7
- Application: For all available inputs.
- Value Range: See Chart 1.
- Default Value: “PWR STBY”
- Function: Selects function for REMOTE PIN7.
Multi Format LCD Monitor 19
Menu Contents
[5] DISPLAY
4P 4P1W1V
C H 1 C H 2
C H 3 C H 4
C H 1
C H 2
C H 3
C H 4
C H 1
W AV E F OR M
C H1
VEC
T OR
4P3W 3P1W
C H 1
C H 2
C H 3
C H 4
C H1
W A VE Y
C H1
W A VE C b
C H 1
W A VE C r
C H 1 C H 2
C H 3
C H1
W AV E F OR M
3P1V 2P1W1V
C H1
VE C T O R
C H 1 C H 2
C H 3
C H 1 C H 2
C H1
W AV E F OR M
C H 1
VE C T O R
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
