ELK ELK-M1RB Operating instructions

Type
Operating instructions
828-397-4200 Voice
828-397-4415 Fax
http://www.elkproducts.com
PO Box 100 • Hwy. 70W Hildebran, NC 28637 • USA
Output Relay Board
ELK-M1RB
APPLICATION:
The ELK-M1RB works with an M1 or M1G Control,
or with an M1XOV or M1XOVR Output Expander,
for converting the low current (50mA) voltage
outputs into SPDT relay outputs. When used
with an M1 Control, the M1RB also provides
voltage outputs 7 & 8, which are ordinarily not
available. Up to 2 M1RBs may be connected to
an M1XOV (voltage only) Output Expander.
FEATURES:
8 Form "C" Relays, SPDT Dry Contact
Heavy Duty Contact Rating
Low Current Draw.
Great For General Purpose Switching.
Plug-in "Removable" Terminal Blocks
LED Status Indicators on all 8 Relays
Twelve (12) Conductor Plug-in Wire Harness
Mounts in Enclosure using ELK-SWG
Glides
SPECIFICATIONS:
Diode Protection Across Relay Coil.
Relay Contact Ratings:
7 Amps @ 28 VDC, 10 Amps @ 125 VAC *
Wire Harness Length: 24"
Operating Voltage: 12 Volts DC Nominal
Current Draw: 0 mA idle, 250 mA Max.
Size: 6" x 3.25" x .75" H
* For UL listed installations the maximum contact ratings
are 4 Amps @ 12 VDC
Features or Specifications subject to change without notice.
Output Relay Board
ELK-M1RB
L530 10/05
1. A single M1RB Output Relay Board can be mounted
inside the M1 enclosure on the left hand side of the M1
board using the supplied ELK-SWG Circuit Board Glides.
Additional relay boards and/or expanders must be
mounted in either an ELK-SWB14 or ELK-SWB28
enclosure. Up to 8 Relay Boards/Expanders can be
mounted in an SWB14 while up to 16 can be mounted
in an SWB28.
The ELK-SWG Circuit Board Glides attach to the
enclosure at strategically placed 2-hole punch
patterns. Note that one hole in each pattern is slightly
larger than the other. The small hole is for a 6/32 type
“F” mounting screw and the large hole is for a half-
moon shape locator tab on the bottom of each glide.
ELK-SWG
2. Starting at the top left corner, loosely start a 6/32”
mounting screw in the small hole of the first 2-hole
pattern. Place the slotted edge of a board glide
under this screw, making sure that the half-moon tab
fits into the larger hole and the grooved edge is
facing down. Tighten the screw using a long
shafted screwdriver. Install a second board glide in
the 2-hole pattern located 6" below. Attach the
second board glide using the same procedures. The
grooved edge of this glide should face up.
3. Slide the M1RB Relay board into the grooves
provided by the glides. The circuit board should
slide freely. If the board is loose or too tight, simply
loosen one of the mounting screws and adjust the
glide to assure a good fit.
Installation
Wiring Connections
1. Turn Off the M1 Master Power Switch.
2. Connect one end of the 12 conductor ribbon cable
(provided) into connector J1 on the M1RB.
4. Connect the other end of the 12 conductor cable to
the connector J16 of the control. Note: If the M1RB
is being used with an M1XOVR Output Expander
the connector is marked J3. If being connected to
an M1XOV there are two connectors, J3 and J4.
J3 provides the 2nd group of 8 outputs while J4
provides the 1st group of 8 outputs.
Continued on next page....
M1RB Output Relay Board
8 Form C Relays
J1
10
11
9
15
16
13
14
12
-
+
8
7
LED
LED
LED
LED
LED
LED
LED
LED
SPDT
Relay
SPDT
Relay
SPDT
Relay
SPDT
Relay
SPDT
Relay
SPDT
Relay
SPDT
Relay
SPDT
Relay
OUT 9 OUT 10
N/O COM N/C
Out
7Neg
N/O COM N/C N/O COM N/C N/O COM N/C
OUT 11 OUT 12 OUT 13 OUT 14
N/O COM N/C N/O COM N/C N/O COM N/C N/O COM N/C
OUT 15 OUT 16
Out
8
Outputs 7 & 8 are low current (50 mA)
12 Volt, and are only available when
connected to J-16 on an M1 Control.
The relay output numbers are relative ONLY when
connected to J-16 on an M1 Control. If connected to
an Output Expander, the numbers must be mapped
to the appropriate numbers of the expander.
5. Connect the relay contacts N/O, COM, or N/C to the devices that are being controlled.
CAUTION: Always remember that the contacts are "dry" (no voltage) and can be used to switch both AC and DC
voltage devices. Always calculate the current draw of the devices together with the M1's total system load
before deciding to draw 12 Volts DC from the Control. This is especially true if connected to the Data Bus cabling
as an auxiliary power supply may be required at intervals along the Data Bus cabling to supplement the M1's
power supply and prevent overloading.
6. Turn the M1 Master Power Switch On.
7. Assign the functionality to the new outputs using the Rules programming from the ELK-RP Software. There is no
enrollment if the M1RB is plugged into J-16 of the main M1 Control. However, if plugged into a new Output
Expander (M1XOV or M1XOVR), that expander must be assigned an address and be be enrolled before any of
the outputs can be used. Refer to the Output Expander instructions.
+VKP A B Neg
To M1 Control
Data Bus Terminals
NOTE Should all relays be activated at the same time, the combined current draw of an M1RB can be over 240mA.
This must be figured into the maximum combined current available from the M1 Control. If an M1RB is connected to
an M1XOV or M1XOVR Output Expander, the additional current draw from these devices must be calculated as well.
Adding an ELK-M1RB to a ELK-M1OV Output Expander
J4
+12
A
B
NEG
J1 J2
++--AB AB
2
3
NC
1
NC
7
8
5
6
4
-
+
Output Expander
8 Voltage / 8 Relays
JP1
Terminate
Data Bus
Yes No
Address
Switch 2 shown in ON position
(Address 2). Other switches Off.
J3
10
11
NC
9
NC
15
16
13
14
12
-
+
+-AB
OUTPUTS NUMBERS ARE RELATIVE TO THIS BOARD ONLY
SPDT
Relay
SPDT
Relay
SPDT
Relay
SPDT
Relay
SPDT
Relay
SPDT
Relay
SPDT
Relay
SPDT
Relay
N/O
COM
N/C
N/O
COM
N/C
N/O
COM
N/C
N/O
COM
N/C
N/O
COM
N/C
N/O
COM
N/C
N/O
COM
N/C
N/O
COM
N/C
OUT
1OUT
2OUT
3OUT
4OUT
5OUT
6OUT
7OUT
8
1248
Door
Strike
+-
24V AC
Transformer
M1XOVR
Red
+12
M1RBOutput Relay Board
8 Form C Relays
J1
10
11
9
15
16
13
14
12
-
+
OUTPUTS NUMBERS ARE RELATIVE TO THIS BOARD ONLY
8
7
LED
LED
LED
LED
LED
LED
LED
LED
SPDT
Relay
SPDT
Relay
SPDT
Relay
SPDT
Relay
SPDT
Relay
SPDT
Relay
SPDT
Relay
SPDT
Relay
OUT 9 OUT 10
N/O COM N/C
Out
7Neg
N/O COM N/C N/O COM N/C N/O COM N/C
OUT 11 OUT 12 OUT 13 OUT 14
N/O COM N/C N/O COM N/C N/O COM N/C N/O COM N/C
OUT 15 OUT 16
Out
8
Red +12 M1RBOutput Relay Board
8 Form C Relays
J1
10
11
9
15
16
13
14
12
-
+
OUTPUTS NUMBERS ARE RELATIVE TO THIS BOARD ONLY
8
7
LED
LED
LED
LED
LED
LED
LED
LED
SPDT
Relay
SPDT
Relay
SPDT
Relay
SPDT
Relay
SPDT
Relay
SPDT
Relay
SPDT
Relay
SPDT
Relay
OUT 9 OUT 10
N/O COM N/C
Out
7Neg
N/O COM N/C N/O COM N/C N/O COM N/C
OUT 11 OUT 12 OUT 13 OUT 14
N/O COM N/C N/O COM N/C N/O COM N/C N/O COM N/C
OUT 15 OUT 16
Out
8
Power
Device,
Indicator,
etc.
NEG -
ELK-M1
Connecting an ELK-M1RB to J16 on the ELK-M1 Control
Control Panel Lower Right Side
OUT1
+12V
NEG
16
15
14
13
12
11
10
9
8
7
DATA B
+12V
DATA BUS
J16
OUT3OUT2
+-+-
+VKP
DATA
A
NEG
EGND
OUTPUTS
AUDIO NETWORK INTERFACE
J7
J1J2
N/CCOMN/O
RS-485 DATA BUS
DATA A
OUT3 On LED
J-16 Programmable Outputs
See Note 1
& Note 2
Siren or Voltage
Voice & Siren
Dry Contact Relay
rated 8A @
12 - 28VDC
See Note 2
OUT 1 OUT 3
N/C
COM
N/O
OUT 2
RED
BLACK
WHITE
GREEN
+VKP
DATA B
DATA A
NEG
EGND
OUT 16
OUT 15
OUT 14
OUT 13
OUT 12
OUT 11
OUT 10
OUT 9
OUT 8
OUT 7
+12V
NEG
Audio Network Interface
(Refer to manual) See Note 5
1
Keypad &
Data Bus
J2 J1
Earth Ground-See Note 3
Keypad
See Note 2
NEG
DATA B
+12V
JP3
DATA A
+
-
+
-See Note 2
Terminating
Resistor
Data Bus
See Note 1
J7
2.5 Amp PTC
protected
1
O - I - B A +
DATA
B
Power
Device,
Indicator,
etc.
  • Page 1 1
  • Page 2 2
  • Page 3 3

ELK ELK-M1RB Operating instructions

Type
Operating instructions

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI