Porter-Cable PCC583B User manual

Brand: Porter-Cable

Model: PCC583B

Category: Bicycle accessories

Type: User manual

18V Cordless / 12VDC Inflator

Instruction manual

Manuel d'instructions

Manual de'instrucciones

www.portercable.com

INSTRUCTIVO DE OPERACI N,

CENTROS DE SERVICIO Y P LIZA DE

GARANT A.

ADVERTENCIA: LÉASE ESTE

INSTRUCTIVO ANTES DE USAR EL

PRODUCTO.

Dispositif de gonflage de 12 V c.c./sans

fil, de 18 V

Inflador inalámbrico de 18 V / 12 VCC

Battery and charger sold separately

CATALOG NUMBER

PCC583B

90577349 PCC583B Inflator.qxd:??????-00 BDL500 laser 7/22/11 3:06 PM Page 1

SAFETY GUIDELINES - DEFINITIONS

It is important for you to read and understand this manual. The information it contains

relates to protecting YOUR SAFETY and PREVENTING PROBLEMS. The symbols

below are used to help you recognize this information.

DANGER: Indicates an imminently hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which, if not avoided, could

result in death or serious injury.

CAUTION: Indicates a potentially haz ard ous situation which, if not avoided, may

result in minor or mod er ate injury.

NOTICE: Used without the safety alert symbol indicates a potentially hazardous

situation which, if not avoided, may result in property damage.

WARNING! Read all instructions before operating product. Failure to follow all

instructions listed below may result in electric shock, fire and/or serious injury.

SAVE THESE INSTRUCTIONS

WARNINGS:

1.) Read these instructions.

2.) Keep these instructions.

3.) Heed all warnings.

4.) Follow all instructions.

5.) Do not use this apparatus near water. Keep the case dry at all times.

6.) Clean only with dry cloth.

7.) Do not block any ventilation openings. Install in accordance with the manufacturers

instructions.

8.) Do not place near any heat sources such as radiators, heat registers, stoves or other

apparatus (including amplifiers) that produce heat.

9.) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized

plug has two blades with one wider than the other. A grounding type plug has two blades

and a third grounding prong. The wide blade or the third prong are provided for your

safety. If the provided plug does not fit into your outlet, consult an electrician for

replacement of the obsolete outlet.

10.) Protect the cord from being walked on or pinched particularly at plugs, convenience

receptacles, and the point where they exit from the apparatus.

11.) Only use attachments / accessories specified by the manufacturer.

12.) Unplug unit when lightning is in the area or when unit is not in use.

13.) Refer all servicing to qualified service personnel. Servicing is required when the

apparatus has been damaged in any way, such as power-supply cord or plug is

damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus

has been exposed to rain or moisture, does not operate normally, or has been dropped.

14.) Do not expose to dripping or splashing. WARNING: To reduce the risk of fire or

electric shock, do not expose this apparatus to rain or moisture.

15.) Do not operate near flammable materials, fumes or gases.

16.) Do not disassemble product. Incorrect reassembly may result in a risk of electric

shock or fire.

17.) Provide adequate ventilation and refrain from placing items on or around the product

during operation.

18.) Do not incinerate the battery even if it is severely damaged or is completely worn

out. The battery can explode in a fire. Check with local codes for possible special

disposal instructions.

19.) If any leakage of liquid from the battery cells occurs, discontinue use immediately

and return the battery to your local PORTER-CABLE Service Center or authorized

service facility.

20.) Never attempt to open the battery for any reason. If the plastic housing of the

battery breaks or cracks, immediately discontinue use and do not recharge.

21.) Keep this product out of the reach of children.

90577349 PCC583B Inflator.qxd:??????-00 BDL500 laser 7/22/11 3:06 PM Page 2

22.) Since the vibration produced by the inflator may cause it to “walk”, do not operate on

a high shelf or other surface. Operate at ground or bench level only.

GENERAL SAFETY RULES

•KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries.

•CONSIDER WORK AREA ENVIRONMENT. Donʼt expose power tools to rain. Donʼt use

power tools in damp or wet locations. Keep work area well lit. Do not use tool in presence

of flammable liquids or gases.

•GUARD AGAINST ELECTRIC SHOCK. Prevent body contact with grounded surfaces.

For example; pipes, radiators, ranges, and refrigerator enclosures.

•KEEP CHILDREN AWAY. Do not let visitors contact tool or extension cord. All visitors

should be kept away from work area.

•STORE IDLE TOOLS. When not in use, tools should be stored in dry, and high or locked-

up place — out of reach of children.

•DONʼT FORCE TOOL. It will do the job better and safer at the rate for which it was intended.

•USE RIGHT TOOL. Donʼt force small tool or attachment to do the job of a heavy-duty

tool. Donʼt use tool for purpose not intended.

•DRESS PROPERLY. Do not wear loose clothing or jewelry. They can be caught in

moving parts. Rubber gloves and non-skid footwear are recommended when working

outdoors. Wear protective hair covering to contain long hair.

•USE SAFETY GLASSES. Also use face or dust mask if operation is dusty.

•DONʼT ABUSE CORD. Never carry tool by cord or yank it to disconnect from receptacle.

Keep cord from heat, oil, and sharp edges.

•SECURE WORK. Use clamps or a vise to hold work. Itʼs safer than using your hand and it

frees both hands to operate tool.

•DONʼT OVERREACH. Keep proper footing and balance at all times.

•MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and safer

performance. Follow instructions for lubricating and changing accessories. Inspect tool

cords periodically and if damaged, have repaired by authorized service facility. Inspect

extension cords periodically and replace if damaged. Keep handles dry, clean, and free

from oil and grease.

•DISCONNECT OR LOCK OFF TOOLS when not in use, before servicing, and when

changing accessories, such as blades, bits, cutters.

•REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that

keys and adjusting wrenches are removed from tool before turning it on.

•AVOID UNINTENTIONAL STARTING. Donʼt carry tool with finger on switch. Be sure

switch is off when plugging in.

•When using an extension cord, be sure to use one heavy enough to carry the current

your product will draw. An undersized cord will cause a drop in line voltage resulting in

loss of power and overheating. The following table shows the correct size to use

depending on cord length and nameplate ampere rating. If in doubt, use the next

heavier gauge. The smaller the gauge number, the heavier the cord.

Recommended Minimum Wire Size for Extension Cords

Total Length of Cord

25 ft. 50 ft. 75 ft. 100 ft. 125 ft. 150 ft. 175 ft.

7.6 m 15.2 m 22.9 m 30.5 m 38.1 m 45.7 m 53.3 m

Wire Size AWG

18 18 16 16 14 14 12

•OUTDOOR USE EXTENSION CORDS. When tools are used outdoors, use only

extension cords intended for use outdoors and so marked.

•STAY ALERT. Watch what you are doing. Use common sense. Do not operate tool when

you are tired.

•CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is

damaged should be carefully checked to determine that it will operate properly and

perform its intended function. Check for alignment of moving parts, binding of moving

parts, breakage of parts, mounting, and any other conditions that may affect its operation.

A guard or other part that is damaged should be properly repaired or replaced by an

authorized service center unless otherwise indicated elsewhere in this instruction manual.

90577349 PCC583B Inflator.qxd:??????-00 BDL500 laser 7/22/11 3:06 PM Page 3

Have defective switches replaced by authorized service center. Do not use tool if switch

does not turn it on and off.

•DO NOT OPERATE portable electric tools near flammable liquids or in gaseous or

explosive atmospheres. Motors in these tools normally spark, and the sparks might ignite

fumes.

ADDITIONAL SAFETY WARNINGS FOR YOUR INFLATOR

WARNING! FOR HOME AND CAR USE ONLY:

• Inflate car and bike tires, balls, rafts, swimming pool floats, air mattresses, and more

in and around the home.

WARNING! RISK TO BREATHING:

•The compressed air from your inflator is not safe for breathing. Never inhale air

from your inflator or from a breathing device connected to the inflator.

WARNING! RISK OF BURSTING:

•Inflate items only to their manufacturerʼs recommendations. Exceeding the pressure

rating could cause them to explode resulting in personal injury.

•Do not leave unit running unattended. Overinflation of tires and other items could result

in serious injury and property damage.

WARNING! RISK OF ELECTRICAL SHOCK:

•Turn off and remove battery from inflator when not in use, when cleaning, or when

changing nozzles.

•Do not expose inflator to rain or wet conditions. Water entering the inflator will

increase the risk of electric shock.

WARNING! RISK OF FALLING:

•Since the vibration produced by the inflator may cause it to “walk”, do not operate

on a high shelf or other surface. Operate at ground or bench level.

WARNING! RISK OF UNSAFE OPERATION:

•Do not modify or attempt to repair. Never drill into, weld, or make any modifications to

the inflator or its attachments.

•Do not operate inflator when car engine is running.

•Operate only with the accessories included or those rated for 160 p.s.i. or higher.

The use of any accessory not recommended for use with this tool could be hazardous.

•Never “horseplay”. High pressure air is dangerous. Donʼt direct air-flow at yourself or others.

WARNING! RISK OF FIRE:

•Inflator can become hot during use. Allow inflator to cool 30 minutes before storing away.

•Never carry the inflator by the hose.

90577349 PCC583B Inflator.qxd:??????-00 BDL500 laser 7/22/11 3:06 PM Page 4

IMPORTANT SAFETY INSTRUCTIONS FOR BATTERY CHARGERS

SAVE THESE INSTRUCTIONS: This manual contains important safety instructions for

battery chargers.

• Before using charger, read all instructions and cautionary markings on charger, battery

pack, and product using battery pack.

WARNING: Shock hazard. Do not allow any liquid to get inside charger.

CAUTION: Burn hazard. To reduce the risk of injury, charge only designated

PORTER-CABLE batteries. Other types of batteries may burst causing personal injury and

damage.

CAUTION: Under certain conditions, with the charger plugged in to the power

supply, the charger can be shorted by foreign material. Foreign materials of a conductive

nature such as, but not limited to, steel wool, aluminum foil, or any buildup of metallic

particles should be kept away from charger cavities. Always unplug the charger from the

1. Power switch

2. LCD (liquid crystal

display)

3. Handle

4. High-volume pump

deflate connection

5. High-volume pump

inflate connection

6. Air hose with

universal valve adaptor

7. Universal valve

adaptor

8. 12 Vdc vehicle

connector adaptor

9. High-volume hose

(unregulated air

pressure hose, no auto

shut-off)

10. Battery compartment

(back of unit)

11. Accessory storage

(back of handle)

FUNCTIONAL DESCRIPTION

Li-Ion Battery Packs and Chargers

Battery: Li-Ion 18V

Charger: Li-Ion

PC18BL

PC18BLX

PC18BLEX

PCLMVC

PCXMVC

Description Cat. #

NI-CD Battery Packs and Chargers

This product can accept any of the batteries and chargers listed in the chart below.

Battery: NI-CD 18V

Charger: NI-CD

PC18B

PCMVC

PCXMVC

Description Cat. #

90577349 PCC583B Inflator.qxd:??????-00 BDL500 laser 7/22/11 3:06 PM Page 5

power supply when there is no battery pack in the cavity. Unplug charger before

attempting to clean.

WARNING:

• DO NOT attempt to charge the battery pack with any chargers other than the ones in

this manual. The charger and battery pack are specifically designed to work together.

• These chargers are not intended for any uses other than charging designated

PORTER-CABLE rechargeable batteries. Any other uses may result in risk of fire,

electric shock or electrocution.

• Do not expose charger to rain or snow.

• Pull by plug rather than cord when disconnecting charger. This will reduce risk of

damage to electric plug and cord.

• Make sure that cord is located so that it will not be stepped on, tripped over, or

otherwise subjected to damage or stress.

• Do not use an extension cord unless it is absolutely necessary. Use of improper

extension cord could result in risk of fire, electric shock, or electrocution.

• An extension cord must have adequate wire size (AWG or American Wire Gauge)

for safety. The smaller the gauge number of the wire, the greater the capacity of the

cable, that is 16 gauge has more capacity than 18 gauge. When using more than one

extension to make up the total length, be sure each individual extension contains at least

the minimum wire size.

• Do not place any object on top of charger or place the charger on a soft surface

that might block the ventilation slots and result in excessive internal heat. Place

the charger in a position away from any heat source. The charger is ventilated

through slots in the top and the bottom of the housing.

• Do not mount charger on wall or permanently affix charger to any surface. The

charger is intended to use on a flat, stable surface (i.e., table top, bench top).

• Do not operate charger with damaged cord or plug — have them replaced immediately.

• Do not operate charger if it has received a sharp blow, been dropped, or otherwise

damaged in any way. Take it to an authorized service center.

• Do not disassemble charger; take it to an authorized service center when service or

repair is required. Incorrect reassembly may result in a risk of electric shock,

electrocution or fire.

• Disconnect the charger from the outlet before attempting any cleaning. This will

reduce the risk of electric shock. Removing the battery pack will not reduce this risk.

• NEVER attempt to connect 2 chargers together.

• The charger is designed to operate on standard household electrical power (120

Volts). Do not attempt to use it on any other voltage.

SAVE THESE INSTRUCTIONS

Important Safety Instruction for Battery Packs

WARNING: For safe operation, read this manual and manuals originally supplied

with tool before using the charger.

The battery pack is not fully charged out of the carton. Before using the battery pack and

charger, read the safety instructions below. Then follow charging procedures outlined.

READ ALL INSTRUCTIONS

• Do not incinerate the battery pack even if it is severely damaged or is completely

worn out. The battery pack can explode in a fire. Toxic fumes and materials are created

when Li-Ion battery packs are burned.

• Do not charge or use battery in explosive atmospheres, such as in the presence of

flammable liquids, gases or dust. Inserting or removing the battery from the charger may

ignite the dust or fumes.

• If battery contents come into contact with the skin, immediately wash area with mild

soap and water. If battery liquid gets into the eye, rinse water over the open eye for 15

minutes or until irritation ceases. If medical attention is needed, the battery electrolyte for

Li-Ion batteries is composed of a mixture of liquid organic carbonates and lithium salts. For

NI-CD batteries it is a 25-35% solution of potassium hydroxide.

• Contents of opened battery cells may cause respiratory irritation.Provide fresh air. If

symptoms persist, seek medical attention.

WARNING: Burn hazard. Battery liquid may be flammable if exposed to spark or flame.

90577349 PCC583B Inflator.qxd:??????-00 BDL500 laser 7/22/11 3:06 PM Page 6

• Charge the battery packs only in PORTER-CABLE chargers.

• DO NOT splash or immerse in water or other liquids. This may cause premature cell failure.

• Do not store or use the tool and battery pack in locations where the temperature

may reach or exceed 105°F (40˚C) (such as outside sheds or metal buildings in

summer).

WARNING: Never attempt to open the battery pack for any reason. If battery pack

case is cracked or damaged, do not insert into charger. Do not crush, drop or damage

battery pack. Do not use a battery pack or charger that has received a sharp blow, been

dropped, run over or damaged in any way (i.e., pierced with a nail, hit with a hammer,

stepped on). Damaged battery packs should be returned to service center for recycling.

Battery Cap Information

Battery storage and carrying caps are provided for use whenever the

battery is out of the tool or charger. Remove cap before placing battery in

charger or tool.

WARNING: Fire hazard. Do not store or carry battery so that metal objects can

contact exposed battery terminals. For example, do not place battery in aprons,

pockets, tool boxes, product kit boxes, drawers, etc., with loose nails, screws, keys, etc.

Transporting batteries can possibly cause fires if the battery terminals inadvertently

come in contact with conductive materials such as keys, coins, hand tools and the

like. The US Department of Transportation Hazardous Material Regulations (HMR)

actually prohibit transporting batteries in commerce or on airplanes (i.e., packed in

suitcases and carry-on luggage) UNLESS they are properly protected from short circuits.

So when transporting individual batteries, make sure that the battery terminals are

protected and well insulated from materials that could contact them and cause a short

circuit. NOTE: Batteries should not be put in checked baggage.

Storage Recommendations

1. The best storage place is one that is cool and dry away from direct sunlight and

excess heat or cold.

2. Long storage will not harm the battery pack or charger.

Charging Procedure

PORTER-CABLE chargers are designed to charge PORTER-CABLE battery packs in

30-60 minutes depending on the pack being charged.

1. Plug the charger into an appropriate outlet before inserting the battery pack.

2. Insert the battery pack into the charger. (Fig. B)

3. The LED will flash indicating that the battery

is being charged.

4. The completion of charge is indicated by the

LED remaining on continuously. The pack is

fully charged and may be used at this time or

left on the charger.

Charger Diagnostics

The charger is designed to detect certain problems that can arise with the battery packs

or the power source. Problems are indicated by one LED flashing in different patterns.

Bad Battery

The charger can detect a weak or damaged battery. The LED flashes in the pattern

indicated on the label. If you see this bad battery blink pattern, do not continue to

charge the battery. Return it to a service center or a collection site for recycling.

Battery Cap

90577349 PCC583B Inflator.qxd:??????-00 BDL500 laser 7/22/11 3:06 PM Page 7

Hot/Cold Pack Delay

When the charger detects a battery that is excessively hot or excessively cold, it

automatically starts a Hot/Cold Pack Delay, suspending charging until the battery

has normalized. After this happens, the charger automatically switches to the Pack

Charging mode. This feature ensures maximum battery life. The light flashes in the

pattern indicated on the label.

Problem Power Line

When the charger is used with some portable power sources such as generators

or sources that convert DC to AC, the charger may temporarily suspend operation.

The LED flashes in the pattern indicated on the label. This indicates that the power

source is out of limits.

Leaving the Battery In the Charger

The charger and battery pack can be left connected with the LED glowing indefinitely.

The charger will keep the battery pack fresh and fully charged. This charger features an

automatic tune-up mode which equals or balances the individual cells in the battery pack

to allow it to function at peak capacity. Battery packs should be tuned up weekly or

whenever the battery no longer delivers the same amount of work. To use the automatic

tune-up mode, place the battery pack in the charger and leave it for at least 8 hours.

Important Charging Notes

1. Longest life and best performance can be obtained if the battery pack is charged when

the air temperature is between 65°F and 75°F (18°- 24°C). DO NOT charge the battery

pack in an air temperature below +40°F (+4.5°C), or above +105°F (+40.5°C). This is

important and will prevent serious damage to the battery pack.

2. The charger and battery pack may become warm to touch while charging. This is a

normal condition, and does not indicate a problem. To facilitate the cooling of the battery

pack after use, avoid placing the charger or battery pack in a warm environment such as

in a metal shed, or an uninsulated trailer.

3. If the battery pack does not charge properly:

a. Check current at receptacle by plugging in a lamp or other appliance

b. Check to see if receptacle is connected to a light switch which turns power off

when you turn out the lights.

c. Move charger and battery pack to a location where the surrounding air

temperature is approximately 65°F - 75°F (18°- 24°C).

d. If charging problems persist, take the tool, battery pack and charger to your

local service center.

4. The battery pack should be recharged when it fails to produce sufficient power on jobs

which were easily done previously. DO NOT CONTINUE to use under these conditions.

Follow the charging procedure. You may also charge a partially used pack whenever you

desire with no adverse affect on the battery pack.

5. Foreign materials of a conductive nature such as, but not limited to, steel wool,

aluminum foil, or any buildup of metallic particles should be kept away from charger

cavities. Always unplug the charger from the power supply when there is no battery pack

in the cavity. Unplug charger before attempting to clean.

6. Do not freeze or immerse charger in water or any other liquid.

WARNING: Shock hazard. Do not allow any liquid to get inside charger. Never attempt

to open the battery pack for any reason. If the plastic housing of the battery pack breaks or

cracks, return to a service center for recycling.

LIQUID CRYSTAL DISPLAY FLUID (FIRST AID MEASURES)

If liquid crystal comes in contact with your skin:

Wash area off completely with plenty of water. Remove contaminated clothing.

If liquid crystal gets into your eye:

Flush the affected eye with clean water and then seek medical attention.

If liquid crystal is swallowed:

Flush your mouth thoroughly with water. Drink large quantities of water and induce

vomiting. Then seek medical attention.

90577349 PCC583B Inflator.qxd:??????-00 BDL500 laser 7/22/11 3:06 PM Page 8

The label on your tool may include the following symbols.

V ..........................volts A..........................amperes

Hz ........................hertz W ........................watts

min........................minutes ......................alternating

current

......................direct current no ........................no load speed

..........................Class II Construction ........................earthing terminal

........................safety alert symbol

INTRODUCTION

INTENDED USE

Your PORTER-CABLE inflater is designed to be used cordless or in most vehicles from

the standard 12 Volt socket to inflate car and bike tires, balls, rafts, air mattresses,

swimming pool floats, etc. This product is intended for household use only.

HOSE CORD AND ACCESSORY STORAGE - FIGURES B,C & D

• Wrap the 12 Vdc cord around the base of the unit and snap the 12 Vdc adapter into its

storage location on the base of the unit (figure B).

• The high volume air hose is located in a storage

compartment on the left side of the unit (figure C).

• The air hose with universal valve adaptor is located

in a storage compartment on the right side of the

unit, store the hose with the lever in the up position.

• The accessories are located in a storage

compartment on the back of the handle (figure D).

90577349 PCC583B Inflator.qxd:??????-00 BDL500 laser 7/22/11 3:06 PM Page 9

FITTING THE ACCESSORIES - FIGURE E

Your inflator is supplied with the standard tapered nozzles and the needle inflator

nozzle (stored in the back of the handle).

• To use the universal valve adaptor, make sure that

the lever is in the up position.

• Place the valve adapter over the stem of the

inflation needle or tapered nozzle (figure E).

• Press the lever on the valve adapter down to lock it

in place.

• Place the inflation needle or tapered nozzle into the

item to be inflated.

Note: Always make sure that the lever is in the up

position when not in use. Operate your inflator only

with the universal valve adaptor or with the included

nozzles.

Note: Make sure that the universal valve adapter is

firmly locked in place before turning the inflator on.

High Volume Hose - Figure F

• To use the high volume hose, remove it from the

side storage location.

• Use the hose with the tapered nozzle for small

openings or without the nozzle for large openings.

Many inflatables have an internal flap that prevents

air loss during inflation, especially air mattresses.

Unless this flap is displaced by the nozzle the

inflatable will not inflate. Push the nozzle firmly into

the valve to make sure that you push this flap out of

the way.

WARNING: Risk of Bursting. Excessive air pressure may cause a hazardous risk of

bursting or personal injury. Check the manufacturer's maximum pressure rating for items

being inflated.

Note: If the pressure rating for the item being inflated is above 100 psi, note that the

maximum run time is 10 minutes, leave to rest for 20 minutes before re-use.

OPERATING THE INFLATOR

WARNING: Do not operate the inflator when the vehicleʼs engine is running.

Note: Make sure that your 12 Volt accessory socket is live. On some vehicles the

accessory socket may only become live when the ignition key is in the accessory position.

To power the display from the 12Vdc adapter:

• Always fully extend the 12 Vdc cord before each use (figure G).

• Insert the 12 Vdc adapter into your vehicles 12 V accessory socket.

• Push the main power switch to the right (inflate position) to power up the LCD (figure H).

90577349 PCC583B Inflator.qxd:??????-00 BDL500 laser 7/22/11 3:06 PM Page 10

To power the LCD from the external battery (cordless operation):

• Insert battery pack into inflator until an audible

click is heard (figure I). Make sure battery pack is

fully seated and fully latched into position.

Note: To remove battery, depress the battery

release button in the back of the battery pack and

pull battery pack out.

• Push the main power switch to the right (inflate

position) to power up the LCD (figure H).

WARNING: Risk of Bursting. Do not leave unit

running unattended. Overinflation of tires and other

items could result in serious injury and property

damage.

QUICK START

WARNING: Never leave inflator running unattended in this mode. In can burst car

tires and other items.

To use your inflator immediately you can do so without setting the automatic shut-off

feature.

• Push the main power switch to the right (inflate

position, figure H).

• To switch between the different units (PSI, BAR or

KPA) press - & + buttons together repeatedly until

the required units are displayed (figure J).

• Connect the universal valve adaptor and an

accessory, if required, to the item to be inflated,

making sure that the lever of the valve adaptor is in

the down position to lock it in place.

Note: Make sure that the universal valve adaptor is

correctly fitted to the item to be inflated.

• To start the inflator, press the power button on the

LCD (figure K).

• When the item is inflated as required or to stop the

inflator at any time press the power button on the

LCD.

Note: When the inflator is shut off, the pressure reading displayed will drop slightly from

the reading displayed while the inflator is running. This pressure reading with the inflator

off is correct.

• Remove the hose from the item and store it on the side of the unit.

• Turn the main power switch to the off (middle) position.

SETTING THE AUTOMATIC SHUT-OFF PRESSURE

Note: The LCD will only show inflation pressures when the inflator is being used.

• To switch between the different units (PSI, BAR or KPA) press - & + buttons together

repeatedly until the required units are displayed (figure J).

• To set shut off pressure, press and hold either + or – button until the display starts to

flash, then release.

• Press + or – button until the desired pressure is displayed.

• The display will flash 3 times and return to a reading of “0.0”. This is normal.

• Connect the universal valve adaptor and accessories, if required, to the item to be

inflated, making sure that the lever of the valve adaptor is in the down position to lock

it in place.

• To start the inflator, press the power button on the LCD (figure K).

• When the item to be inflated has reached the preset value, the unit will automatically turn off.

Note: You may notice the actual pressure reading may drop after a couple of seconds,

this is normal.

• To stop the inflator at any time press the power button on the LCD (figure K).

• Remove the valve adaptor or accessory from the inflated item and the 12 Volt adapter

90577349 PCC583B Inflator.qxd:??????-00 BDL500 laser 7/22/11 3:06 PM Page 11

from your vehicle's 12 Volt accessory socket (if used).

• Turn the main power switch to the off (middle) position.

Note: If the main power switch is turned off, all settings will be lost and will need to be re-

entered following the instructions under the heading 'Setting the automatic shut-off

pressure'. This is a safety feature to prevent the risk of items OVER INFLATING.

USING THE INFLATOR AS A PRESSURE GAUGE

• Push the main power switch to the right (inflate position) to power up the LCD (figure H).

• Connect the universal valve adaptor to the item to be checked.

• The LCD will display the itemʼs pressure.

• After checking, turn the main power switch off (middle position) and return the air hose to

the storage location.

OPERATING THE HIGH-VOLUME PUMP

WARNING: Do not operate the pump when the vehicleʼs engine is running.

Note: Make sure that your 12 Vdc accessory socket is live. On some vehicles the

accessory socket may only become live when the ignition key is in the accessory position.

To inflate using the high-volume pump (i.e air mattresses, rafts, swimming pool

floats):

Note: The pump mode DOES NOT have an auto shut-off feature.

• Remove the high-volume hose from the storage

compartment on the side of the unit and connect it to

the high-volume pump inflate connection (figure L).

• Insert the hose (with accessories if required) into

the item to be inflated.

• To start the pump, push the main power switch to

the left (pump position) (figure M). The pump will

start immediately and the LCD screeen will not be

illuminated.

• When the item is inflated as required or to stop the

pump at any time return the main power switch to the

off position.

• Remove the hose from the item and store it on the unit.

To deflate using the high-volume pump (i.e air mattresses, rafts, swimming pool

floats):

Note: The pump mode DOES NOT have an auto shut-off feature.

• Remove the high-volume hose from the storage

compartment on the side of the unit and connect it to

the high-volume pump deflate connection (figure N).

• Insert the hose (with accessories if required) into

the item to be deflated.

• To start the pump, push the main power switch to

the left (pump position) (figure O). The pump will

start immediately and the LCD screeen will not be

illuminated.

• When the item is deflated or to stop the pump at

any time return the main power switch to the off

position.

• Remove the hose from the item and store it on the unit.

REPLACING THE FUSE IN THE VEHICLE DC ACCESSORY PLUG

• Remove the cap by turning it counterclockwise.

• Remove the center pin.

• Remove the fuse.

• Insert a new fuse of the same type and size (8A/250V).

• Replace the cap and center pin.

• Tighten the cap by turning clockwise onto the plug.

90577349 PCC583B Inflator.qxd:??????-00 BDL500 laser 7/22/11 3:07 PM Page 12

MAINTENANCE

Clean only with a dry cloth. Never let any liquid get inside the tool; never immerse any

part of the tool into a liquid.

IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and

adjustment (other than those listed in this manual) should be performed by authorized

service centers or other qualified service personnel, always using identical replacement parts.

TROUBLESHOOTING

Problem Possible Cause Possible Solution

• Unit will not start. 12 Volt adapter Connect the 12 Volt

not connected. adapter.

Accessory socket Turn key to accessory

not live. position.

Main ON/OFF switch not in Turn main switch to

correct position. required position.

The fuse in the 12 Volt adapter Replace the fuse with

is blown. one of the same size

and type (8A/250V).

Cord or switch is damaged. Have cord or switch

replaced at a Porter-Cable

Service Center or

Authorized Servicer.

• Will not inflate. Incorrect mode selected. Select correct mode.

Battery depleted. Recharge battery and

retry.

For assistance with your product, visit our website at www.portercable.com for a list of service

centers, or call the Porter-Cable Customer Care Center at (888) 848-5175.

REPLACEMENT PARTS

Use only identical replacement parts. For a parts list or to order parts, visit our service website at

www.portercable.com. You can also order parts from your nearest PORTER-CABLE Factory Service

Center or PORTER-CABLE Authorized Warranty Service Center. Or, you can call our Customer

Care Center at (888) 848-5175.

SERVICE AND REPAIRS

All quality tools will eventually require servicing and/or replacement of parts. For information about

PORTER-CABLE, its factory service centers or authorized warranty service centers, visit our website

at www.portercable.com or call our Customer Care Center at (888) 848-5175. All repairs made by our

service centers are fully guaranteed against defective material and workmanship. We cannot

guarantee repairs made or attempted by others.

You can also write to us for information at PORTER-CABLE, 4825 Highway 45 North, Jackson,

Tennessee 38305, (888) 848-5175 - Attention: Product Service. Be sure to include all of the

information shown on the nameplate of your tool (model number, type, serial number, etc.).

ACCESSORIES

WARNING: Since accessories, other than those offered by PORTER-CABLE,

have not been tested with this product, use of such accessories with this tool could be

hazardous. To reduce the risk of injury, only PORTER-CABLE recommended accessories

should be used with this product.

A complete line of accessories is available from your PORTER-CABLE Factory Service

Center or a PORTER-CABLE Authorized Warranty Service Center. Please visit our Web

Site www.portercable.com for a catalog or for the name of your nearest supplier.

THREE YEAR LIMITED WARRANTY

PORTER-CABLE will repair or replace, without charge, any defects due to faulty

materials or workmanship for three years from the date of purchase for tools (two years

for batteries). This warranty does not cover part failure due to normal wear or tool

abuse. For further detail of warranty coverage and warranty repair information, visit

www.portercable.com or call (888) 848-5175. This warranty does not apply to

accessories or damage caused where repairs have been made or attempted by others.

90577349 PCC583B Inflator.qxd:??????-00 BDL500 laser 7/22/11 3:07 PM Page 13

This warranty gives you specific legal rights and you may have other rights which vary

in certain states or provinces.

In addition to the warranty, PORTER-CABLE tools are covered by our:

1 YEAR FREE SERVICE: PORTER-CABLE will maintain the tool and replace worn parts

caused by normal use, for free, any time during the first year after purchase.

90 DAY MONEY BACK GUARANTEE: If you are not completely satisfied with the

performance of your PORTER-CABLE Power Tool for any reason, you can return it within

90 days from the date of purchase with a receipt for a full refund – no questions asked.

LATIN AMERICA: This warranty does not apply to products sold in Latin America. For

products sold in Latin America, see country specific

warranty information contained in the packaging, call the local company or see website

for warranty information.

To register your tool for warranty service visit our website at www.portercable.com.

WARNING LABEL REPLACEMENT

If your warning labels become illegible or are missing, call (888) 848-5175 for a free

replacement.

The following are PORTER-CABLE trademarks for one or more power tools and accessories: a gray

and black color scheme; a “four point star” design; and three contrasting/outlined longitudinal stripes.

The following are also trademarks for one or more PORTER-CABLE and Delta products: Les

éléments ci-dessous sont des marques de commerce des outils et des accessoires de PORTER-

CABLE : un agencement de couleurs grise et noire; un motif d « étoile à quatre pointes » et trois

bandes longitudinales contrastantes/à contours. Les marques suivantes sont également des

marques de commerce se rapportant à un ou plusieurs produits PORTER-CABLE ou Delta : Las

siguientes son marcas comerciales PORTER-CABLE que distinguen a una o m s herramientas y

accesorios: un gr fico de color gris y negro; un dise o de “estrella de cuatro puntas” y tres franjas

longitudinales contrastantes/delineadas. Las siguientes también son marcas comerciales para uno o

m s productos de PORTER-CABLE y Delta: 2 BY 4®, 890™, Air America®, AIRBOSS™, Auto-

Set®, B.O.S.S.®, Bammer®, Biesemeyer®, Builders Saw®, Charge Air®, Charge Air Pro®,

CONTRACTOR SUPERDUTY®, Contractor's Saw®, Delta®, DELTA®, Delta Industrial®, DELTA

MACHINERY & DESIGN™, Delta Shopmaster and Design®, Delta X5®, Deltacraft®,

DELTAGRAM®, Do It. Feel It.®, DUAL LASERLOC AND DESIGN®, EASY AIR®, EASY AIR TO

GO™, ENDURADIAMOND®, Ex-Cell®, Front Bevel Lock®, Get Yours While the Sun Shines®, Grip

to Fit®, GRIPVAC™, GTF®, HICKORY WOODWORKING®, Homecraft®, HP FRAMER HIGH

PRESSURE®, IMPACT SERIES™, Innovation That Works®, Jet-Lock®, Job Boss®, Kickstand®,

LASERLOC®, LONG-LASTING WORK LIFE®, MAX FORCE™, MAX LIFE®, Micro-Set®, Midi-

Lathe®, Monsoon®, MONSTER-CARBIDE™, Network®, OLDHAM®, Omnijig®, PC EDGE®,

Performance Crew™, Performance Gear®, Pocket Cutter®, Porta-Band®, Porta-Plane®, PORTER-

CABLE®, PORTER-CABLE Professional Power Tools®, Powerback®, POZI-STOP™, Pressure

Wave®, PRO 4000®, Proair®, Quicksand and Design®, Quickset II®, QUIET DRIVE

TECHNOLOGY™, QUIET DRIVE TECHNOLOGY AND DESIGN™, Quik-Change®, QUIK-TILT®,

RAPID-RELEASE™, RAZOR®, Redefining Performance®, Riptide®, Safe Guard II®, Sand Trap

and Design®, Sanding Center®, Saw Boss®, Shop Boss®, Sidekick®, Site Boss®, Speed-Bloc®,

Speedmatic®, Stair Ease®, Steel Driver Series®, SUPERDUTY®, T4 & DESIGN®, THE

AMERICAN WOODSHOP®, THE PROFESSIONAL EDGE®, Thin-Line®, Tiger Saw®,

TIGERCLAW®, TIGERCLAW AND DESIGN®, Torq-Buster®, TRU-MATCH®, T-Square®,

Twinlaser®, Unifence®, Uniguard®, UNIRIP®, UNISAW®, UNITED STATES SAW®, Veri-Set®,

Versa-Feeder®, VIPER®, VT™, VT RAZOR™, Water Driver®, WATER VROOM®, Waveform®,

Whisper Series®, X5®, YOUR ACHIEVEMENT. OUR TOOLS.®

Trademarks noted with ® are registered in the United States Patent and Trademark Office and may

also be registered in other countries. Other trademarks may apply. Les marques de commerce

suivies du symbole ® sont enregistrées auprès du United States Patent and Trademark Office et

peuvent être enregistrées dans d autres pays. D autres marques de commerce peuvent également

être applicables. Las marcas comerciales con el s mbolo ® est n registradas en la Oficina de

patentes y marcas comerciales de Estados Unidos (United States Patent and Trademark Office), y

también pueden estar registradas en otros pa ses. Posiblemente se apliquen otras marcas

comerciales registradas.

4825 Highway 45

North Jackson, TN 38305

(888) 848-5175 www.portercable.com

90577349 PCC583B Inflator.qxd:??????-00 BDL500 laser 7/22/11 3:07 PM Page 14

Dispositif de gonflage de 12 V

c.c./sans fil, de 18 V

Manuel d'instructions

N° DE CATALOGUE

PCC583B

Blocs-piles et chargeurs vendus séparément

www.portercable.com

90577349 PCC583B Inflator.qxd:??????-00 BDL500 laser 7/22/11 3:07 PM Page 15

LIGNES DIRECTRICES EN MATIÈRE DE SÉCURITÉ - DÉFINITIONS

Il est important que vous lisiez et compreniez ce mode d emploi. Les informations qu il

contient concernent VOTRE SÉCURITÉ et visent à ÉVITER TOUT PROBL ME. Les

symboles ci-dessous servent à vous aider à reconnaître cette information.

DANGER : Indique une situation dangereuse imminente qui, si elle n est pas évitée,

causera la mort ou des graves blessures.

AVERTISSEMENT : Indique une situation potentiellement

dangereuse qui, si elle n est pas évitée, pourrait causer la mort ou de graves blessures.

MISE EN GARDE : Indique une situation potentiellement dangereuse qui, si elle

n est pas évitée, pourrait causer des blessures mineures ou modérées.

AVIS : Utilisé sans le symbole d alerte à la sécurité, indique une situation potentiellement

dangereuse qui, si elle n est pas évitée, peut résulter en des dommages à la propriété.

AVERTISSEMENT! Lire toutes les directives avant d'utiliser le produit. Tout manquement

aux directives suivantes pose des risques de choc électrique, d'incendie et/ou de blessure

grave. CONSERVER CES DIRECTIVES

AVERTISSEMENTS :

1.) Lire ces directives.

2.) Conserver ces directives.

3.) Respecter tous les avertissements.

4.) Respecter toutes les directives.

5.) Ne pas utiliser cet appareil près dʼune source dʼeau. Garder le boîtier sec en tout temps.

6.) Nettoyer uniquement avec un linge sec.

7.) Ne pas obstruer les ouvertures dʼaération. Installer conformément aux directives du

fabricant.

8.) Ne pas placer lʼappareil près dʼune source de chaleur, comme un radiateur, un

registre de chaleur, une cuisinière ou tout autre appareil (y compris un amplificateur)

produisant de la chaleur.

9.) Ne pas modifier la caractéristique de sécurité de la fiche polarisée ou de la prise de

mise à la terre. Une fiche polarisée est munie de deux lames, lʼune étant plus large

que lʼautre. Une prise de mise à la terre est munie de deux lames et dʼune broche de

mise à la terre. La lame large ou la broche de mise à la terre est conçue pour votre

sécurité. Si la fiche ne peut pas être insérée dans votre prise de courant, consulter un

électricien pour quʼil remplace la prise de courant périmée.

10.) Protéger le cordon pour éviter que ce dernier ne soit écrasé ou pincé,

particulièrement en ce qui concerne la fiche dʼalimentation électrique, la prise de

courant et la sortie de lʼappareil.

11.) Nʼutiliser que les accessoires spécifiés par le fabricant.

12.) Débrancher lʼappareil à lʼapproche dʼun orage électrique ou lorsquʼil ne sert pas.

13.) Recourir à un personnel dʼentretien qualifié pour toutes les tâches dʼentretien. Un

entretien est nécessaire lorsque lʼappareil subit des dommages de quelque sorte que

ce soit, comme des dommages concernant le cordon dʼalimentation ou la fiche, le

renversement dʼun liquide ou la chute dʼobjets dans lʼappareil, lʼexposition de lʼappareil

à la pluie ou à lʼhumidité, le mauvais fonctionnement de lʼappareil ou la chute de ce

dernier.

14.) Ne pas exposer lʼappareil à lʼécoulement ou à lʼéclaboussement dʼun liquide.

AVERTISSEMENTS : pour réduire le risque dʼincendie ou de choc électrique, ne

pas exposer cet appareil à la pluie ou à lʼhumidité.

15.) Ne pas utiliser lʼappareil près de substances, de vapeurs ou de gaz inflammables.

16.) Ne pas démonter le produit. Un appareil mal réassemblé peut causer un choc

électrique ou un incendie.

17.) Veiller à assurer une aération adéquate et sʼabstenir de placer des objets sur

lʼappareil ou autour de ce dernier lors de son fonctionnement.

18.) Ne pas incinérer la batterie, même si elle est très endommagée ou complètement

usée. La batterie peut exploser dans un incendie. Vérifier la réglementation locale

relative à la mise au rebut des batteries.

90577349 PCC583B Inflator.qxd:??????-00 BDL500 laser 7/22/11 3:07 PM Page 16

19.) Si une fuite liquide des cellules de batterie survient, interrompre immédiatement

lʼutilisation de lʼappareil et retourner la pile au centre de réparation Black & Decker ou

dans un autre centre de réparation autorisé.

20.) Ne jamais tenter dʼouvrir la batterie, pour quelque raison que ce soit. Si le boîtier de

plastique de la batterie se brise ou se fissure, interrompre immédiatement lʼutilisation

de lʼappareil et ne pas le recharger.

21.) Garder ce produit hors de la portée des enfants.

22.) La vibration produite par le dispositif de gonflage peut le faire déplacer, il importe

donc de ne pas le mettre sur une tablette haute ou sur toute autre surface surélevée.

Faire fonctionner lʼappareil au sol ou au niveau du banc seulement.

RÈGLES GÉNÉRALES DE SÉCURITÉ

•GARDER LA ZONE DE TRAVAIL PROPRE. Les zones et établis encombrés sont

souvent des causes de blessures.

•PENSER À L'ENVIRONNEMENT DE LA ZONE DE TRAVAIL. Ne pas exposer les

outils électriques à la pluie. Ne pas utiliser les outils électriques dans un endroit humide

ou mouillé. Tenir la zone de travail bien éclairée. Ne pas utiliser l'outil en présence de

liquides ou de gaz inflammables.

•DISPOSITIF DE PROTECTION CONTRE LES CHOCS ÉLECTRIQUES. Empêche tout

contact corporel avec les surfaces mises à la terre. Par exemple, les tuyaux, radiateurs,

cuisinières et les enveloppes de réfrigérateur.

•TENIR LES ENFANTS À L'ÉCART. Ne pas laisser les visiteurs entrer en contact avec

l'outil ou la rallonge. Tous les visiteurs doivent être tenus à l'écart de la zone de travail.

•RANGER LES OUTILS INUTILISÉS. Lorsqu'ils ne sont pas utilisés, les outils doivent

être rangés dans un endroit sec, en hauteur ou dans un endroit verrouillé, hors de la

portée des enfants.

•NE PAS FORCER L'OUTIL. Le travail sera mieux accompli et sera moins dangereux

au rythme prévu pour l'outil.

•UTILISER L'OUTIL APPROPRIÉ. Ne pas forcer un petit outil ou accessoire à effectuer

un travail convenant à un outil pour service intensif. Ne pas utiliser l'outil à d'autres fins

que celles prévues.

•S'HABILLER DE MANIÈRE APPROPRIÉE. Ne pas porter de vêtements amples ni de

bijoux. Ils peuvent s'enchevêtrer dans les pièces mobiles. Des gants de caoutchouc et

des chaussures antidérapantes sont recommandés pour les travaux à l'extérieur. Se

couvrir les cheveux s'ils sont longs.

•PORTER DES LUNETTES DE SÉCURITÉ. Utiliser également un masque facial ou

anti-poussières si l'opération génère de la poussière.

•NE PAS UTILISER ABUSIVEMENT LE CORDON. Ne jamais transporter l'outil par son

cordon ou tirer sur ce dernier pour le débrancher du réceptacle. Tenir le cordon éloigné

de la chaleur, de l'huile et des bords tranchants.

•FIXER LA PIÈCE. Utiliser des brides ou un étau pour retenir la pièce. C'est plus

sécuritaire que d'utiliser votre main et cela vous permet d'utiliser les deux mains pour

faire fonctionner l'outil.

•NE PAS TROP TENDRE LES BRAS. Conserver son équilibre en tout temps.

•PRENDRE SOIN DES OUTILS. S'assurer que les outils sont aiguisés et propres afin

d'optimiser sécurité et performance. Suivre les consignes de graissage et de

changement d'accessoires. Inspecter périodiquement les cordons de l'outil. S'ils sont

endommagés, les faire réparer par un établissement de réparation autorisé. Inspecter

régulièrement les rallonges électriques et remplacer si endommagées. Maintenir les

poignées sèches, propres et exemptes d'huile et de graisse.

•DÉBRANCHER OU VERROUILLER LES OUTILS lorsqu'ils ne sont pas utilisés, avant

toute réparation et au moment de changer d'accessoire (lames, mèches, couteaux).

•RETIRER LES CLÉS À MOLETTE ET LES CLÉS DE RÉGLAGE. S'habituer à vérifier

que les clés et les clés de réglage ont été retirées de l'outil avant de le mettre en marche.

•EMPÊCHER UN RISQUE DE DÉMARRAGE ACCIDENTEL. Ne pas transporter

l'appareil électrique alors que le doigt repose sur l'interrupteur. S'assurer que

l'interrupteur est à la position arrêt au moment de brancher l'outil.

90577349 PCC583B Inflator.qxd:??????-00 BDL500 laser 7/22/11 3:07 PM Page 17

• En cas d utilisation d une rallonge, s assurer que les valeurs nominales de la rallonge

utilisée correspondent bien à celles de l outil alimenté. L usage d une rallonge de calibre

insuffisant causera une chute de tension entraînant perte de puissance et surchauffe. Le

tableau ci-dessous illustre les calibres à utiliser selon la longueur de rallonge et l intensité

nominale indiquée sur la plaque signalétique. En cas de doutes, utiliser le calibre suivant.

Plus le calibre est petit, plus la rallonge peut supporter de courant.

Calibre de fil minimum recommandé pour les rallonges

Longueur totale de la rallonge

25 pi 50 pi 75 pi 100 pi 125 pi 150 pi 175 pi

7,6 m 15,2 m 22,9 m 30,5 m 38,1 m 45,7 m 53,3 m

Calibre AWG

18 18 16 16 14 14 12

•RALLONGES POUR UTILISATION EXTÉRIEURE. Si l'outil est utilisé à l'extérieur,

utiliser uniquement des rallonges prévues à cet effet et ainsi marquées.

•RESTER VIGILANT. Surveiller son travail. Faire preuve de jugement. Ne pas utiliser

l'outil en cas de fatigue.

•VÉRIFIER LES PIÈCES ENDOMMAGÉES. Si un dispositif de protection, ou tout autre

pièce, est endommagé, il faut faire examiner soigneusement l'outil, avant toute

utilisation ultérieure, afin d'assurer un fonctionnement adéquat selon sa fonction prévue.

Vérifier l'alignement des pièces mobiles, la présence de grippage des pièces mobiles,

de rupture de pièces, l'assemblage et tout autre problème pouvant nuire au

fonctionnement de l'outil. Un dispositif de protection endommagé, ou toute autre pièce

endommagée, doit être réparé ou remplacé adéquatement par un centre de réparation

autorisé à moins d'un avis contraire indiqué dans le présent mode d'emploi. Faire

remplacer les interrupteurs défectueux à un centre de réparation autorisé. Ne pas

utiliser l'outil si l'interrupteur ne fonctionne pas.

•NE PAS UTILISER d'outils électriques portatifs à proximité de liquides inflammables ou

dans une atmosphère gazeuse ou explosive. Les moteurs de ces outils produisent

normalement des étincelles qui pourraient enflammer des vapeurs.

AVERTISSEMENT! POUR UNE UTILISATION À LA MAISON OU DANS LA VOITURE

SEULEMENT :

• Gonfler les pneus de voiture ou de vélo, les balles, les radeaux, les flotteurs de piscine,

les matelas pneumatiques et bien plus dans la maison et autour de celle-ci.

AVERTISSEMENT! Inhalation risquée :

•Il est dangereux de respirer l'air comprimé sortant du dispositif de gonflage. Ne

jamais inhaler l'air provenant du dispositif de gonflage ou d'un appareil respiratoire

raccordé au dispositif de gonflage.

AVERTISSEMENT! Risque d'éclatement :

•Gonfler les objets uniquement selon les recommandations du fabricant. Le fait de

dépasser leur capacité de pression risque de les faire exploser et de causer ainsi des

blessures corporelles.

•Ne pas laisser le dispositif de gonflage fonctionner sans supervision. Il risque de

faire éclater des pneus ou d'autres objets.

AVERTISSEMENT! Risque de choc électrique :

•Éteindre le dispositif de gonflage et retirer le bloc-piles lorsquʼil nʼest pas utilisé,

au moment de le nettoyer ou de changer de buse.

•Ne pas exposer le dispositif de gonflage à la pluie ou à d'autres conditions où il

pourrait être mouillé. La pénétration de lʼeau dans le dispositif de gonflage augmente

le risque de choc électrique.

AVERTISSEMENT! Risque de chute :

•La vibration produite par le dispositif de gonflage peut le faire déplacer, il importe

donc de ne pas le mettre sur une tablette haute ou sur toute autre surface

surélevée. Faire fonctionner l'appareil au sol ou au niveau du banc.

AVERTISSEMENT! Risque d'utilisation dangereuse :

AUTRES AVERTISSEMENTS DE SÉCURITÉ CONCERNANT LE

DISPOSITIF DE GONFLAGE

90577349 PCC583B Inflator.qxd:??????-00 BDL500 laser 7/22/11 3:07 PM Page 18

1. Bouton dʼalimentation

2. ACL (affichage à

cristaux liquides)

3. Poignée

4. Raccord de

dégonflage de pompe à

volume élevé

5. Raccord de gonflage

de pompe à volume élevé

6. Flexible dʼair pourvu

dʼun adaptateur de valve

universelle

7. Adaptateur de valve

universelle

8. Adaptateur pour

connecteur de véhicule

de 12 V c.c.

9. Flexible à volume

élevé (flexible de

pression dʼair non régulée,

aucun arrêt automatique)

10. Logement du bloc-

piles (arrière de lʼappareil)

11. Rangement des

accessoires (arrière de la

poignée)

DESCRIPTION FONCTIONNELLE

Blocs-piles au Li-Ion et chargeurs

correspondants

Bloc-piles : Li-Ion 18V

Chargeur : pour piles au

Li-Ion

PC18BL

PC18BLX

PC18BLEX

PCLMVC

PCXMVC

Description N° de cat.

Blocs-piles au NI-CD et chargeurs

correspondants

Ce produit est compatible avec tous les modèles de piles et de chargeurs

énumérés dans le tableau ci-dessous.

Bloc-piles : NI-CD 18V

Chargeur : pour piles au

NI-CD

PC18B

PCMVC

PCXMVC

Description N° de cat.

•Ne pas modifier l'appareil ou tenter de le réparer. Ne jamais percer, souder le

réservoir ni apporter aucune modification à celui-ci ou à ses fixations.

•Ne pas faire fonctionner le dispositif de gonflage lorsque le moteur du véhicule

tourne.

•Le faire fonctionner uniquement avec les accessoires inclus ou ceux dont la

valeur nominale est de 160 p.s.i. ou plus. L'utilisation de tout accessoire non

recommandée avec cet outil pourrait s'avérer dangereuse.

•Ne jamais chahuter brutalement le dispositif de gonflage. L'air sous haute pression

est dangereux. Ne pas diriger le débit d'air vers soi ou les autres.

AVERTISSEMENT! Risque d'incendie :

•Le dispositif de gonflage peut devenir chaud durant son utilisation. Le laisser

refroidir durant 30 minutes avant de le ranger.

•Ne jamais transporter le dispositif de gonflage par son tuyau.

90577349 PCC583B Inflator.qxd:??????-00 BDL500 laser 7/22/11 3:07 PM Page 19

CONSERVER CES DIRECTIVES : ce mode d emploi comprend d importantes directives

de sécurité pour les chargeurs de piles.

• Avant d utiliser le chargeur, lire toutes les directives et tous les avertissements figurant sur

le chargeur, le bloc-piles et le produit utilisé avec le bloc-piles.

AVERTISSEMENT : risque de choc électrique. Éviter la pénétration de tout liquide

dans le chargeur.

MISE EN GARDE : risque de brûlure. Pour réduire le risque de blessures,

charger uniquement des piles PORTER-CABLE conseillées. D autres types de piles

peuvent exploser et provoquer des blessures corporelles et des dommages.

MISE EN GARDE : dans certaines circonstances, lorsque le chargeur est branché

au bloc d alimentation, le chargeur peut être court-circuité par des corps étrangers

conducteurs tels que, mais sans s y limiter, la laine d acier, le papier d aluminium ou toute

accumulation de particules métalliques. Ils doivent être maintenus à distance des

ouvertures du chargeur. Débrancher systématiquement celui-ci si aucun bloc-piles n y est

inséré. Débrancher le chargeur avant tout nettoyage.

AVERTISSEMENT :

• NE PAS tenter de charger le bloc-piles avec autre chose qu’un chargeur de marque.

Les chargeurs et blocs-piles sont conçus spécialement pour fonctionner ensemble.

• Ces chargeurs ne sont pas destinés à être utilisés à dʼautres fins que celles de

charger les piles rechargeables conseillées PORTER-CABLE. Toute autre utilisation

risque de provoquer un incendie, un choc électrique ou une électrocution.

• Protéger le chargeur de la pluie et de la neige.

• Tirer la fiche plutôt que le cordon pour débrancher le chargeur ou pour débrancher

les cordons à l’aide de la fonction de guirlande. Cela permet de réduire le risque

dʼendommager la fiche ou le cordon dʼalimentation.

• S’assurer que le cordon est situé en lieu sûr de manière à ce que personne ne

marche ni ne trébuche dessus ou à ce qu’il ne soit pas endommagé ni soumis à une

tension.

• Ne pas utiliser de rallonge à moins que cela ne soit absolument nécessaire.

Lʼutilisation dʼune rallonge inadéquate risque dʼentraîner un incendie, un choc électrique ou

une électrocution.

• Pour la sécurité de l’utilisateur, utiliser une rallonge de calibre adéquat (AWG,

American Wire Gauge [calibrage américain normalisé des fils]). Plus le numéro de

calibre de fil est petit et plus sa capacité est grande, par exemple un calibre 16 a plus de

capacité quʼun calibre 18. Si plus dʼune rallonge est utilisée pour obtenir la longueur totale,

sʼassurer que chaque rallonge présente au moins le calibre de fil minimum.

• Ne pas mettre d’objet sur le chargeur ni mettre ce dernier sur une surface souple,

ce qui pourrait causer l’obstruction des fentes de ventilation et, du fait, provoquer

une chaleur interne excessive. Éloigner le chargeur de toute source de chaleur. La

ventilation du chargeur se fait par les fentes pratiquées dans les parties supérieures et

inférieures du boîtier.

• Ne pas installer le chargeur sur un mur ni le fixer de manière permanente sur toute

surface. Le chargeur est destiné à une utilisation sur une surface plane et stable (c.-à-d.

un dessus de table ou dʼétabli).

• Ne pas faire fonctionner le chargeur si la fiche ou le cordon est endommagé; les

remplacer immédiatement.

• Ne jamais se servir d’un chargeur qui a subi un choc violent, qui est tombé par

terre ou qui est endommagé de quelque manière que ce soit. Le faire vérifier dans

un centre de réparation autorisé.

• Ne pas démonter le chargeur; confier lʼentretien ou la réparation de lʼappareil à un

centre de réparation autorisé. Le remontage non conforme du chargeur comporte des

risques de choc électrique, dʼélectrocution ou dʼincendie.

• Débrancher le chargeur avant de le nettoyer. Cela réduira le risque de choc électrique.

Le risque ne sera pas éliminé en enlevant simplement le bloc-piles.

DIRECTIVES DE SÉCURITÉ IMPORTANTES POUR

LES CHARGEURS DE PILES

90577349 PCC583B Inflator.qxd:??????-00 BDL500 laser 7/22/11 3:07 PM Page 20

Page is loading ...

Porter-Cable PCC583B User manual

Brand: Porter-Cable

Model: PCC583B

Category: Bicycle accessories

Type: User manual

Download PDF

report

in other languages

français: Porter-Cable PCC583B Manuel utilisateur
español: Porter-Cable PCC583B Manual de usuario

Porter-Cable PCC583B User manual

Porter-Cable PCC583B User manual

in other languages

Related papers

Other documents