REV 01
QSG 891-00592 REV01
NOTE: Please scan the QR Code to access the electronic version of Installation Guide
or visit the website:
Cumberland: http://www.cumberlandpoultry.com
AP: http://www.automatedproduction.com
GSI Electronics Inc.
5200 Armand Frappier Saint-Hubert, Qc
Canada J3Z 1G5
Phone: 1-877-926-2777
E-mail: [email protected]
Light Sensor
• Only properly trained service personnel may perform installation and service
procedures. (In other words: electricians, service personnel employed by or active
in an organization, business, or service).
• All power sources must be disconnected prior to wiring and installing.
• Electrostatic discharge (ESD) can damage equipment and impair electrical
circuitry. ESD damage occurs when electronic components are improperly
handled and can result in complete or intermittent failures.
• Warranty is void if the Legacy Connect is used in a manner not specied by the
manufacturer.
3 - NOTICES
Functional Ground Terminal. Primarily used for functional earth
terminals which are generally associated with test and measurement
circuits. These terminals are not for safety earthing purposes but provide
an earth reference point.
Protective Earth Ground Terminal. Primarily used for protective earth
terminals. These terminals connect to conductive parts of a device for
the purpose of safety and is intended to be connected to an external
system for protective grounding.
WARNING: Read the following text carefully; it contains important
information which, if ignored, may cause the controller to operate
improperly.
High Voltage. Hazard of electrical shock.
4 - SYMBOLS
EN
ADO824642
Cumberland
AP
2 - ORDERING INFORMATION
GSIE Part
Number
GSI Part
Number Description Lbs Kgs
028-00677 EDG-180 Light Sensor Kit 1.77 0.80
Service Parts
832-00177 EDG-179 Light Sensor, 0-10V Output 0.331 0.15
028-00655 EDG-168 Voltage Converter Assembly 0-10V
to 0-5V 1.44 0.65
EDG-161 Sensor Bracket 0.25 0.11
Continuous monitoring of light intensity is now possible with your EDGE® system.
The EDGE® Light Sensor kit includes a signal converter that must be wired between
the output of the sensor and the input of your EDGE system; requires EDGE software
version 2.5 or higher.
For optimum measurements, keep the light-sensitive area of the sensor free of
dust to ensure correct measurements. Place the sensor in the air path of an inlet
that opens rst, in order to minimize the build-up of dust on the sensor. In dusty
applications, the sensor should be mounted in a location that allows for cleaning.
The sensor should be placed in a position which is representative of the light level
in the house. Sunlight and objects obstructing internal lighting should be taken into
account during installation.
1 - INTRODUCTION
Light Sensitive
Area
5 - WIRING DIAGRAM
NOTES:
• If a cables with shields are used, twist both shields from each cable together and use a marrette (twist-on wire connector) to secure the connection.
Make sure that the shield does not touch any other bare wire and the resistor.
AP/Cumberland recommends to add a heat shrink on it.
• The maximum diameter of the cable must be less than 6.5 mm.
• Cable glands must be correctly tightened to guarantee the sealing of the junction box.
• Use the 4 screws included in the kit to close the cover on the junction box.
• The wire color used in this drawing is only for reference, it can be dierent on the sensor.
• Maximum volts should be set to 3.6V in the EDGE conguration page.
0-10V to 0-3.6V Converter Wiring Diagram
with EDG-179 or 832-00177 Light Sensor
R=6.8K
0-10V SENSOR CABLE
EDGE INPUT CABLE
Equivalent Circuit
Brown - 24+
White - 0-100 LUX - OUT+
White - 0-100 LUX - OUT+
Black - 0-1000 LUX - OUT+
Black - 0-1000 LUX - OUT+
Blue - GND
24V
IN+
GND
Wire Nut
GND
24V+
GND
24V+
GND
IN
GND
IN
GND
IN
GND
IN
EDGE Expansion
Box
(EDG-168 or 028-00655)
Signal Convertor
(EDG-179 or
832-00177)
Light Sensor
0-10V Sensor Cable
EDGE INPUT CABLE
Brown - 24+
Blue - GND
R=6.8K
7 - CONFIGURING EDGE SOFTWARE ALARMS FOR LIGHT
SENSOR
1. Select the Setup Icon.
2. Select the room you wish to add the alarm to.
3. At the bottom of the page select the Alarm button.
4. Select Generic Input.
5. Select the sensor you want to add the alarm to.
6. Select Use low alarm and/or Use high alarm and then enter the specic alarm
criteria you want in the elds.
6 - CONFIGURING EDGE SOFTWARE FOR LIGHT SENSOR
NOTE: To complete these steps, you must have Setup Privileges.
1. Select the Equipment Congifuration Icon.
2. Select the room you wish to add the equipment to.
3. Scroll down and select Generic Input.
4. Select the Add or Copy equipment button.
5. Give the sensor a Name and then select the Signal Type, Units, and Precision.Light Sensor
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Powermaster High Traffic Commercial Gate Operator UL 325 User manual
-
Eaton Durant AMBASSADOR 57605-452 Operating instructions
-
GarrettCom ES42 User manual
-
Ford Edge Owner's manual
-
Adam Equipment Adam-4000 User manual
-
GE NX-548E User manual
-
Ford 2007 Edge Owner's manual
-
-
-
