OTC 6732 Operating instructions

OTC
Brand
OTC
Model
6732
Type
Operating instructions
Sheet No.
Issue Date: Rev. C, June 5, 2014
© Bosch Automotive Service Solutions LLC
Form No. 537545
Item
No.
Part
No.
No.
Req’d
1 531738 1 Installer Cup
2 537499 1 Receiving Tube
3 537500 1 Remover
4 537501 1 Remover
Description
GM Ball Joint Update Kit
(Use with OTC Ball Joint Kit 6530 or 7918)
Application: Use with an OTC ball joint press to remove and install upper and lower ball joints on
the GM vehicles listed.
Parts List
Safety Precautions
Caution: To prevent personal injury,
• WeareyeprotectionthatmeetsANSIZ87.1andOSHAstandards.
• Beforerepairingavehicle,blockthewheelstopreventthevehiclefrommoving.
• Checkthenalalignmentoftheballjointpressandtoolingwiththecomponentsbefore
exertingpressuretoremoveorreplaceaballjoint.
1
3
Refer to any operating instructions included with the product for detailed
information about operation, testing, disassembly, reassembly, and
preventive maintenance.
Items found in this parts list have been carefully tested and selected by
OTC. Therefore:UseonlygenuineOTCreplacementparts.
Additional questions can be directed to our Technical Service Dept.
1 of 2
4
2
Parts List &
OperatingInstructions
for: 6732
655 EISENHOWER DRIVE
OWATONNA, MN 55060 USA
PHONE: (507) 455-7000
TECH. SERV.: (800) 533-6127
FAX: (800) 955-8329
ORDER ENTRY: (800) 533-6127
FAX: (800) 283-8665
INTERNATIONAL SALES: (507) 455-7223
FAX: (507) 455-7063
PartsList&OperatingInstructions Form No. 537545, Sheet 1 of 2, Back
Figure 1 Figure 2
1. Position the tools as shown to remove or install the upper or lower ball joint. Note for installation: Clean the control
arm or knuckle, and coat the I.D. with a suitable lubricant.
2. Tighten the forcing screw until it meets the cup, and check the alignment of all tooling and components. Continue
tightening the forcing screw until the ball joint is removed or installed.
RemovingandInstallingtheLowerBallJoint
OperatingInstructions
Applications:1999-20001/2-tonSilverado,Sierra4WD(std.cab)
2001-20041/2-tonSilverado,Sierra2WD/4WD
2000-20041/2-tonSuburban,Tahoe,Yukon,Denali2WD/4WD
2002-20041/2-tonAvalanche2WD/4WD
2002-2004CadillacEscalade2WD/4WD
2003-20041/2-&3/4-tonExpress&SavanaVan4WD
Figure 1 Figure 2
C-frame
No. 7248;
not included
RemovingandInstallingtheUpperBallJoint
No. 537499
ReceivingTube
Previously Released
Adapter
No. 305227
Previously
Released
Receiving Cup
No. 39776
Previously
Released
Receiving Cup
No. 204508
C-frame
No. 7248;
not included
C-frame
No. 7248;
not included
Previously
Released
Receiving Cup
No. 29504
No. 537500
Remover
Previously Released
Adapter
No. 305228
C-frame
No. 7248;
not included
Previously
Released
Installer Cup
No. 313969
Previously
Released
Receiving Cup
No. 39776
Removal Installation
Removal Installation
Sheet No.
Issue Date: Rev. C, June 5, 2014
© Bosch Automotive Service Solutions LLC
PartsList&OperatingInstructions FormNo.537545
2 of 2
OperatingInstructions
Applications:2002-2005ChevroletTrailBlazer,
GMCEnvoy,&OldsmobileBravada
1. Position the tools as shown to remove or install the upper or lower ball joint. Note for installation: Clean the control
arm or knuckle, and coat the I.D. with a suitable lubricant.
2. Tighten the forcing screw until it meets the cup, and check the alignment of all tooling and components. Continue
tightening the forcing screw until the ball joint is removed or installed.
RemovingandInstallingtheLowerBallJoint
Figure 1 Figure 2
Figure 1 Figure 2
RemovingandInstallingtheUpperBallJoint
C-frame
No. 7248;
not included
Previously Released
Adapter
No. 305227
Previously Released
Receiving Tube
No. 222306
Previously Released
Receiving Cup
No. 204508
C-frame
No. 7248;
not included
Previously
Released
Receiving Cup
No. 38354
C-frame
No. 7248;
not included
C-frame
No. 7248;
not included
Previously Released
Installer Cup
No. 313969
Previously Released
Remover
No. 313968
No. 531738
Removal Installation
Removal Installation
Previously
Released
Adapter
No. 38354
PartsList&OperatingInstructions
OperatingInstructions
Applications:1995-1999ChevroletTahoe,GMCYukon4WD
2000ChevroletTahoeZ714WD
1995-19991/2-&3/4-tonSuburban4WD
1995-20001/2-,3/4-,&1-tonChevrolet&GMC4WDtrucks
1999-2000CadillacEscalade4WD
2001-20031/2-tonSierra&Silverado2WD/4WDHDCrewCab
1999-20043/4-tonSierra&Silverado2WD/4WD
2000-20043/4-tonSuburban&GMCYukon2WD/4WD
2001-20041-tonSierra&Silverado4WD
2002-20043/4-tonAvalanche2WD/4WD
2003-2004HummerH2
1. Position the tools as shown to remove or install the upper or lower ball joint. Note for installation: Clean the control
arm or knuckle, and coat the I.D. with a suitable lubricant.
2. Tighten the forcing screw until it meets the cup, and check the alignment of all tooling and components. Continue
tightening the forcing screw until the ball joint is removed or installed.
RemovingandInstallingtheLowerBallJoint
Figure 1 Figure 2
Figure 1 Figure 2
RemovingandInstallingtheUpperBallJoint(withpress-inballjoint)
C-frame
No. 7248;
not included
Previously Released
Adapter
No. 305227
Previously Released
Receiving Tube
No. 222306
C-frame
No. 7248;
not included
Previously Released
Receiving Cup
No. 204508
Previously Released
Receiving Tube
No. 222307
C-frame
No. 7248;
not included
Previously
Released
Receiving
Cup
No. 29504
No. 537501
Remover
Previously Released
Adapter
No. 305228
C-frame
No. 7248;
not included
Previously
Released
Receiving Cup
No. 204508
Previously Released
Receiver Tube
No. 29504 Previously Released
Adapter
No. 305227
Form No. 537545, Sheet 2 of 2, Back
Previously
Released Adapter
No. 305227
Removal Installation
Removal Installation
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

OTC 6732 Operating instructions

OTC
Brand
OTC
Model
6732
Type
Operating instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents