Wagan 12V Roadside Impact Wrench User manual

Category
Power impact wrenches
Type
User manual

This manual is also suitable for

12V Roadside Impact Wrench
by Wagan Tech
®
1
www.wagan.com
Thank you for purchasing the 12V Roadside Impact Wrench
by Wagan Tech
®
.
With normal care and proper treatment, it will provide years of reliable service.
Please read all operating instructions carefully before use.
INTENDED USAGE
The 12V Roadside Impact Wrench is designed to loosen or tighten vehicle lug
nuts. It is intended for occasional intermittent use, not commercial purposes.
WARNINGS
Read all safety warnings and instructions. Use the 12V Roadside Impact
Wrench in accordance with these instructions, taking into account the
working conditions and the work to be performed. Use of the power tool
for operations different than those intended could result in a hazardous
situation and serious injury.
Keep children and bystanders away while operating a power tool.
Never leave the impact wrench unattended while connected to the 12V DC
socket.
Do not use the tool in potentially explosive environments containing
combustible liquids, gases or dust. Electrical tools generate sparks that can
ignite the dust or vapors.
Do not expose to water or use in rainy conditions to avoid risk of electrical
shock.
Do not use if there are any visible signs of damage to the wrench or the
power cord.
Dress properly. Do not wear loose clothing or jewelry. Keep your hair,
clothing and gloves away from moving parts that they can get caught on.
Do not touch the wrench head during operation.
Only connect to a 12V DC power source.
Do not use any socket not supplied with this impact wrench.
©2019 Wagan Corporation. All Rights Reserved.
Wagan Tech and wagan.com are trademarks of Wagan Corporation.
User’s Manual—Read before using this equipment
2
After tightening with the wrench, it is important to check the specified
torque by using a torque wrench. Consult your vehicle’s manual for
recommended torque specifications.
Do not overtighten lug nuts.
Do not overload the tool. Do not apply excessive pressure to the impact
wrench. If the nuts cannot be moved and the wrench freezes, stop
operation. Either use a more powerful tool or continue with a manual
wrench. Do not attempt to continue to turn the nuts manually with the
Roadside Impact Wrench.
Do not use the impact wrench continuously for more than 10 minutes.
Do not operate the tool without a load at full speed for any length of time.
12V Roadside Impact Wrench
by Wagan Tech
®
3
www.wagan.com
FEATURES
6-pt. Double Socket, 21 + 23 mm
6-pt. Double Socket, 17 + 19 mm
½" Square Drive Anvil
Switch: Loosening Position (L)
Switch: Tightening Position (T)
Fused 12V DC Plug
©2019 Wagan Corporation. All Rights Reserved.
Wagan Tech and wagan.com are trademarks of Wagan Corporation.
User’s Manual—Read before using this equipment
4
SPECIFICATIONS
Voltage 12V DC
Power Draw 150 Watts
Max Torque 258 ft-lb
Cable Length 9.5 ft (2.9 m)
Fuse Rating 15A, 250V
Square Drive Anvil ½” (12.7 mm)
Included Socket Diameters 17/19 mm, 21/23 mm
OPERATION
Start the engine before operating the wrench. Keep the engine running while
using. Unplug impact wrench from 12V DC socket when not in use.
Switch operation
For loosening lug nuts, press the side of the switch marked “L
For tightening lug nuts, press the side of the switch marked “T”
To power off, simply release the switch
IMPORTANT: After tightening with the wrench, it is important to check the
specified torque by using a torque wrench. Consult your vehicle’s manual
for recommended torque specifications.
Loosen Lug Nuts
Use your jack to lift up your car and ensure there is about 2 inches (5 cm)
between the tire and the ground
Refer to your car’s operation manual for the recommended lifting
point and safe operations
12V Roadside Impact Wrench
by Wagan Tech
®
5
www.wagan.com
Insert the 12V power plug into the vehicle’s power socket.
Attach an appropriately sized socket to the ½" square drive anvil.
Place the socket onto the lug nut and press the side of the switch with “L
mark to start loosening the lug nuts.
The motor starts and after a short warm-up time, the impact wrench gives a
pulse to the socket.
Repeat for remaining lug nuts until they are loose.
Tighten Lug Nuts
Put the wheel into position and hand-tighten the lug nuts prior to tightening
with the wrench. This helps avoid cross threading the lug nut.
Press the side of the switch with “T” mark to start tightening the lug nuts.
The lug nut will be tight enough when 4-5 clicks are heard. DO NOT over
tighten.
Tighten the nuts in a star pattern.
IMPORTANT: After tightening with the wrench, it is important to check the
specified torque by using a torque wrench. Consult your vehicle’s manual
for recommended torque specifications.
PRODUCT CARE
Handle the tool and accessories with care and keep them clean to ensure a
long service life.
Do not make any modifications to the tool. Repairs to the tool or power cord
should be carried out by an authorized service technician.
Disconnect the plug from the cigarette lighter before cleaning parts of the
tool, or if there is a problem with the tool.
Do not use caustic, abrasive or solvent-based products for cleaning.
Use a soft, dry cloth to wipe the tool clean.
©2019 Wagan Corporation. All Rights Reserved.
Wagan Tech and wagan.com are trademarks of Wagan Corporation.
User’s Manual—Read before using this equipment
6
Prevent oil or oil products from entering the plastic casing. The chemicals
they contain could corrode or damage the plastic. Grease and oil-based
grime must be immediately wiped off the tool and accessories with a
slightly damp cloth.
Store idle power tools out of reach of children and do not allow people
unfamiliar with the power tool or these instructions operate it. Power tools
are dangerous in the hands of untrained users.
Disposal of this product should only be done in accordance with the current
regulations.
REPLACING THE FUSE IN THE 12V DC PLUG
1. Twist off the upper cover of the 12V DC plug.
2. Remove the faulty fuse.
3. Insert a new fuse of the same type (a spare fuse is included in the case)
4. Twist the cover back onto the plug.
TROUBLESHOOTING
Problem Possible Solution
The impact wrench will not start Check if the vehicle battery is dead
Check if the 12V socket is faulty
Check the fuse in the 12V DC plug of
the wrench
A wheel nut cannot be unscrewed or
tightened
Check that the correct rotation
direction has been selected
The WAGAN Corporation warranty is limited to products sold only in
the United States.
Warranty Duration:
Product is warranted to the original purchaser for a period of one (1) year from
the original purchase date, to be free of defects in material and workmanship.
WAGAN Corporation disclaims any liability for consequential damages. In no event
will WAGAN Corporation be responsible for any amount of damages beyond the
amount paid for the product at retail.
Warranty Performance:
During the warranty period, a product with a defect will be replaced with a
comparable model when the product is returned to WAGAN Corporation with an
original store receipt. WAGAN Corporation will, at its discretion, replace or repair
the defective part. The replacement product will be warranted for the balance of the
original warranty period. This warranty does not extend to any units which have
been used in violation of written instructions furnished.
Warranty Disclaimers:
This warranty is in lieu of all warranties expressed or implied and no representative
or person is authorized to assume any other liability in connection with the sale of our
products. There shall be no claims for defects or failure of performance or product
failure under any theory of tort, contract or commercial law including,but not limited
to negligence, gross negligence, strict liability, breach of warranty, and breach of
contract.
Returns:
WAGAN Corporation is not responsible for any item(s) returned without an official
Return Authorization number (RA#). Please contact our customer service team by
phone or email to obtain an RA#. You can also visit our website and chat with our team
during our normal business hours. For more details and instructions on how to process
a warranty claim, please read the “Returns” section under the “Contact” page on our
website. WAGAN Corporation is not responsible for any shipping charges incurred in
returning the item(s) back to the company for repair or replacement.
Register your product online at http://tinyurl.com/wagan-registration to be added to
our email list. You will receive previews on our upcoming products, promotions, and
events.
©2015
WAGAN Corp. Limited Warranty
12V Roadside Impact Wrench
de Wagan Tech
®
11
www.wagan.com
CARACTERÍSTICAS
Conector hexagonal doble, 21 + 23 mm
Conector hexagonal doble, 17 + 19 mm
Yunque impulsor ½"
Interruptor: Posición de afloje (L)
Interruptor: Posición de ajuste (T)
Enchufe de 12V CC
con fusible
31088 San Clemente Street
Hayward, CA 94544, U.S.A.
Tel: +1.510.471.9221
U.S. & Canada Toll Free: +1.800.231.5806
customerservice@wagan.com
www.wagan.com
©2019 Wagan Corporation. All Rights Reserved
Wagan Tech and wagan.com are trademarks of Wagan Corporation
© Corporación Wagan 2019. Todos los derechos reservados
Wagan Tech y wagan.com son marcas registradas de la Corporación Wagan
© 2019 Wagan Corporation. Tous droits réservés.
Wagan Tech et wagan.com sont des marques de commerce utilisées par Wagan Corporation.
REV20190625-ESF
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28

Wagan 12V Roadside Impact Wrench User manual

Category
Power impact wrenches
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI