Whirlpool AWD 121 (NA) Owner's manual

Instructions for installation and use

www.aristonappliances.us

Washer-dryer

safe

and easy to use

AWD 121

Lavasecadora

segura

y fácil de usar

Lavante -

Séchante

sûr

et facile à utiliser

How to get better results

The secrets

of fabrics

How to get better results

Instructions for

installation and use

NA

Mode

dinstallation et demploi

F

Instrucciones para

la instalación y el uso

SP

Instructions for installation and use

www.aristonappliances.us

1.

Introduction (pages 3-4-5)

The top ten reasons for buying your washer-dryer. Also covered:

1. Important Safety Instructions for you and your family.

Read this section carefully.

2. Helpful Hints on using your new Washer-Dryer

3. Improving Dryer Efficiency

4. Pre-Installation

2

Installation (pages 6-7-8)

Installation, after delivery or transport, is the most important

operation for the correct functioning of your washing machine.

Always check:

1. That the electric system conforms to regulations;

2. That the inlet and drain hoses are connected correctly.

Never use hoses that have already been used.

3. That the washing machine is levelled properly - improving

the performance of your washing machine.

4. THAT THE DRUM'S SHIPPING BOLTS HAVE BEEN

REMOVED FROM THE BACK OF THE WASHER-DRYER.

3. What goes in your washing machine and how

to start it (pages 8-9)

A correct distribution of your laundry is vital to the successful

outcome of the wash and the life of the washer-dryer. Learn all

the tips and secrets to dividing your linen: color, type of fabric.

4.



Understanding the control panel (page 10)

This Washer-dryer’s

control panel is very simple. It has only a

few essential buttons to help you choose any type of wash and

dry cycle, ranging from the most energetic, capable of cleaning

a mechanic’s overalls, to the most delicate for wool.

Familiarizing yourself with it will help you get the best out of

your wash while helping your machine last longer.

6.



Useful tips to wash, dry and ...

to avoid mistakes (pages 12-13-14)

Years back, our grandmothers were the ones who gave us good

advice - and in those days synthetic fibers did not exist: washing

was easy. Today, your washer-dryer offers you helpful advice

allowing you even to wash wool better than an expert laundress

would by hand.

5. Guide to the wash programs (page 11)

Here is an easy table to help you choose the right program,

temperature, detergents and possible additives. Choose the

right program and you will get better results with your wash

while saving time, water and energy, day after day.

7.



The detergent dispenser (page 15)

How to use the detergent dispenser and the bleach

compartment.

8.

Problems and solutions (pages 16-17)

Before calling a technician, read these pages. Immediate

solutions can be found for a many problems. If the problem

persists, call the Customer Service. They will be glad to help

you.

9. Care and maintenance (page 17-18)

With just a bit of care, the washer-dryer will repay you with

outstanding performance for years and years to come.

10.



Technical characteristics (page 19)

Here are the technical features of your washer-dryer: model

number, electric and water specifications, size, capacity, speed

of the spin cycle and compliance with US & Canadian

regulations.

Here are the 10 topics explained in this manual. Read, learn and have fun. You will discover many secret ways to

get a better wash more easily, and making your washer-dryer last longer.

Quick guide

2

Instructions for installation and use

www.aristonappliances.us

3

Save these instructions

Your safety and that of your children

Important Safety Instructions

Your washing machine has been built in

compliance with the strictest international

safety regulations, to protect you and all your

family.

WARNING -To reduce the risk of fire, electrical shock, or

injury to persons when using your appliance, follow basic

precautions, including the following:

1. Read all instructions before using the appliance.

2. Do not wash or dry articles that have been previously

cleaned in, washed in, or spotted with gasoline, dry cleaning

solvents, other flammable or explosive substances as they

emit vapors that could ignite or explode.

3. Do not allow children to play on or in the appliance. Close

supervision of children is necessary when the appliance is

used near children.

4. Before the appliance is removed from service or discarded,

remove the door.

5. Do not reach into the appliance if the tub or drum is

moving.

6. Do not install or store this appliance where it will be exposed

to the weather.

7. Do not tamper with controls.

9. Do not add gasoline, dry-cleaning solvents, or other

flammable or explosive substances to the wash water. These

substances give off vapors, that could ignite or explode.

10. Under certain conditions, Hydrogen gas may be produced

in a hot water system that has not been used for 2 weeks or

more. HYDROGEN GAS IS EXPLOSIVE. If the hot water

system has not been used for such a period, before using a

washing machine or combination washer washer-dryer, turn

on all hot after faucets and let the water flow from each for

several minutes. This will release any accumulated Hydrogen.

11. Do not use fabric softeners or products to reduce static

unless recommended by the manufacturers of the fabric

softener product.

12. Do not use heat to dry articles containing foam rubber or

similar textured rubber-like materials.

13. Check the Coin Trap every few months to remove any

coins, buttons or similar size objects.

14. Do not place items exposed to cooking oil in your dryer.

Items contaminated with cooking oils may contribute to a

chemical reaction that could cause a load to catch fire.

8. Do not repair or replace any part of the appliance or attempt

any servicing unless specifically recommended in the user-

maintenance instructions or in published user-repair instructions

that you understand and have the skills to carry out.

Introduction

Here are 9 of the best reasons for buying your Washer-

Dryer :

1. Maximum Energy and Water Savings

This appliance is engineered to provide valuable energy

and water savings when compared to other washer-dryers.

2. Space Savings

The Washer-Dryer is designed to utilize horizontal and

vertical space effectively.

3. Combined Washing & Drying

No need for two separate machines for two tasks and no

more transferring clothes from one to the other. Program

the Washer Dryer and you have a two-in-one.

4. Improved Operation

With a spin speed of 1200 RPM, more water is extracted,

allowing improved dry times.

5. Maintenance free

This appliance needs no cleaning of lint after drying

6. Easy Operation

This appliance is simple to use as a washer or as a dryer –

or it can go seamlessly from wash to the dry functions.

7. Better Clothing Appearance

This Washer-Dryer has no agitator to damage your clothes

so they look better and last longer.

8. Placement Options

The Washer-Dryer’s sleek Italian design makes it a perfect

appliance for any Kitchen or Laundry Room. Its compact

size makes the Washer-Dryer a perfect for placement on

each floor of your home.

9. Convenience

This appliance can be permanenty installed and be made

portable with casters and the faucet adapter kit (sold

separately as accessories) where needed.

Congratulations on your new Washer-Dryer. In addition to its award winning design, this is a highly sophisticated engineered

product that will give you many years of satisfaction. Please spend a few moments to read the Owners Manual. This will

show you ways to best utilize your valuable purchase

.

Instructions for installation and use

www.aristonappliances.us

 4

Your Washer Dryer features three different speeds during

the wash cycle. During the Cotton cycle the drum spins at

1,200 or 800 rpm depending on how you set it. During

Permanent Press the drum spins at 850 rpm. During

delicates, the drum spins at 500 rpm. When drying heavy

cotton articles such as bath towels or jeans, be sure the

“Regular” washer setting is selected. The faster spinning

will extract more water from these highly absorbent fabrics

and reduce the degree of dampness as the machine goes

into the drying mode. This will cut down on your drying

time.

Use Liquid Fabric Softener. Fill the softener compartment

up to the level marked. Using fabric softener fluffs out

clothes immediately after the wash cycle. This helps speed

drying time and reduce wrinkles.

This Washer Dryer is a 110 Volt machine, so the heating

element requires more time to achieve full heat than a larger

220 volt unit requires. The heating element will take about

10 minutes to reach full heat.

To dry your laundry, the Washer Dryer blows heated air

into the rotating drum. As the drum tumbles your laundry,

the warm air dries it. If the drum is overfilled with laundry,

the air is not allowed to circulate and clothes will not dry

properly.

Use Low sudsing Detergent. This is recommended for all

front loading washers. It ensures there is no over sudsing,

which may reduce the performance of your machine. Also,

this prevents damage to your machine which may be caused

by excess suds entering the condensing chamber and

clogging the fan blower mechanism with lint.

When sorting laundry always take into consideration the

quantity and type of fabric contained in the load. Highly

absorbent fabrics such as those used in towels or jeans

will absorb more water and become very heavy when

saturated. If you notice that your clothes are taking longer

than usual to dry you may be overloading the machine, or

washing too many highly absorbent articles for a single load.

Helpful Hints

Safety

The lightning flash with arrowhead symbol,

within an equilateral triangle, is intended to alert

the user to the presence of uninsulated “dan-

gerous voltage” within the product’s enclosure

that may be of sufficient magnitude to consti-

tute a risk of electric

shock to persons.

The exclamation

point within an equilat-

eral triangle is intended

to alert the user to the

presence of important

operating and mainte-

nance (servicing) in-

structions in the l

CAUTION:

To reduce the risk of electric shock, DO NOT

remove cover (or back)/no user servicable

parts inside.

Refer for servicing to qualified services

personnel.

The model number of this product may be found on the

back of the unit; the serial number of the label affixed to

the back of the unit.

You should note the model and serial numbers of this

unit in the space provided. Retain this booklet as a

permanent record of your purchase to aid in identifi-

cation in the event of theft.

MODEL N.______________________

SERIAL N.______________________

WARNING:

TO PREVENT FIRE OR SHOCK HAZARD DO NOT

EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

C

U

L

US LISTED

®

Indesit Company

offers to his customers products

with the ENERGY STAR Label.

This appliance was tested by UL

and conforms with both Canadian

and U.S. UL safety requirements

and displays their Mark.

Instructions for installation and use

www.aristonappliances.us

Your washer dryer operates on 110 volts and has a 1,300

watt dryer. It will take a longer time to dry clothes than a

traditional dryer (which operates on 220 volts, 5,000 watts).

However, with the following tips, you can increase the

efficiency of the dryer.

1. DOOR REMAINS LOCKED DURING DRYING: The door

is electronically kept locked drying cycle, with the

Mode+Door Lock light on. This prevents any starting and

shutting the heater, which in turn conserves energy by

trapping the heat.

2. FABRIC SOFTENER: When the Wash and Dry cycles are

set to run consecutively, the preheat function comes on

automatically. In this, the heater is turned on during the last

spin cycle of the wash program. In the Regular Wash

program, the clothes will be getting spun at 1,200 rpm, while

hot air from the dryer will be entering the drum at the same

time. While centrifugal force causes clothes to stick to the

sides of the drum, the hot air will “bake” them to the sides. It

may take 30 minutes or more for the clothes to unstick and

fall into the drum. USING LIQUID FABRIC SOFTENER WILL

CAUSE THE CLOTHES TO UNSTICK IMMEDIATELY. THIS

HELPS DRY CLOTHES FASTER AND CAUSES LESS

WRINKLES.

3.OVERLOADING: The drum has a capacity of

12 lbs. While this is the largest drum available on any

combination washer-dryer, it is smaller than a standard U.S.

washer. The drum should not be overloaded. With too many

clothes, airflow is reduced, increasing drying time. A

maximum of 2/3 of the drum full of clothes is recommeded

for ideal drying.

4. OVER DRYING: This machine uses a condensing dryer.

In this cold water is used to condense the moisture from the

hot air. Since there is no external exhaust system, the

moisture remains in the machine. Frequently, when it seems

the clothes are damp, it is actually the remaining moisture

(like dew). Take clothes out and within a few minutes they

will be dry. Do not overdry the clothes.

5. USE LOW SUDSING DETERGENT: By using low sudsing

detergent, you are preventing suds from entering the

condensing chamber. When suds enter the condensing

chamber, lint particles can clog up the chamber and the fan

blower. Over time, this reduces drying efficiency and may

require the fan blower (impeller) to be cleaned.

Dryer Efficiency

This appliance is an automatic washer with a capacity of up to:

12 lbs.

Your new appliance is carefully engineered product. Many times

what appears to be a reason to call for service, requires nothing

more than a simple adjustment you can easily make in your

own home.

You will be charged for a service call while the appliance

is in warranty if the problem is not caused by defective

product workmanship or materials covered by this

warranty.

To avoid a charge for an unnecessary service call, and before

calling a serviceman, please refer to the troubleshooting section

for situations that you can remedy. This section is included on

pages 16-17 of this Use and Care Book.

Your Washer-Dryer is front loading, with an extra large door

opening for easier access. It has 9 wash cycles in addition

to

extra rinse

and

pre wash

cycles.

You will obviously want to obtain the best possible wash. By

reading and following the instructions in this booklet you will

achieve excellent results.

Please, ensure that the instructions are followed. If you should

need any further advice or assistance, please, contact the

dealer where your machine was purchased.

PRE-INSTALLATION

1. The washer must be installed on a strong level floor, and in

protected, dry, and well-ventilated area close to a power and

water supply of sufficient capacity.

2. Installation on Carpet or Wood increases vibrations.

• Carpets - place on light carpet only.

• Wood - brace floor with screws and place additional sheets

of plywood before installation.

3. Dryer installation and grounding should be done in

accordance with local codes by a qualified installer.

“Installation Instructions” are included in your Use and Care

manual for the Installer’ s reference.

4. The washer should be plugged into a properly grounded

three (3) prong electrical outlet of 120 Volt, 1300 W, 13 A,

60 Hz. It should not be controlled by a wall switch or pull

cord which might be turned off accidentally.

5

Instructions for installation and use

www.aristonappliances.us

WARNING Electrical Requirements

Electrical Shock Hazard (death, fire or electrical shock):

1) Plug into a grounded 3 prong outlet.

2) Do not remove ground prong.

3) Do not use an adapter or an extension cord.

4) The Appliance should be connected to an Individual

Branch Circuit with N. 14 AWG Wire and Protected by 15

A Fuse.

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of malfunction,

or breakdown, grounding will reduce the risk of electric shock

by providing a path of least resistance for electric current. This

appliance is equipped with a cord having an equipment-

grounding conductor and grounding plug. The plug must be

plugged into an appropriate outlet that is properly installed and

grounded in accordance with all local codes and ordinances.

WARNING - Improper connection of the equipment-grounding

conductor can result in a risk of electric shock. Check a qualified

electrician if you are in doubt as to whether the appliance is

properly grounded.

Do not modify the plug provided with the appliance. If it will not

fit the outlet, have a proper outlet installed by a qualified

electrician.

6

After removing the appliance from its packaging, check that it

is intact. The inside of the machine is supported, for

transportation, by four shipping bolts on the back panel.

Before using the washer-dryer,

remove the external shipping bolts,

remove the spacers together with the

rubber tubes attached to them (save

all the parts) and use the plastic

blanking plugs provided to fill in the

holes. Use the wrench provided to

remove the external bolts.

Attach the two rubber hoses provided to the red (hot) and

white (cold) water inlets on the back (top right) or the appliance.

Using the “U”-Connector provided, place the drain hose into

the drain pipe (or the sink.) See Plumbing on Page 7 for more

details.

Leveling

The washer-dryer must be levelled appropriately in order to

guarantee its correct functioning. To level the appliance, the front

feet must be adjusted; the angle of inclination, measured according

to the worktop, must not exceed 2°.

WARNING

Excessive Weight Hazard

Use two or more people to move

and install your appliance.

Failure to do so can result in

back or other injury

The front feet are self-locking & adjustable

For your own protection, and to prevent accidents,

injury and fire, please read the following carefully:

1. Destroy the carton and plastic bags, after the washer-dryer

has been unpacked.

2. Children should never be left alone or unattended in the

area where appliances are located.

3. Washer installation and grounding must be done in

accordance with local codes by a qualified installer. Installation

instructions are packed in new washer to the installer’s

reference.

4. ONLY Low Sudsing detergent is recommended for this

appliance.

Installation

When the new washer-dryer arrives

Whether new or just transported to a new house, installation is extremely important

for the correct functioning of your washer-dryer.

5. The washer must be

plugged into a properly

grounded 3-prong

electrical outlet. For

your safety, the third or

round grounding prong

must never be

removed.

DO NOT USE AN

EXTENSION CORD.

6. Repair or replace-

ment of a part should

be made only by a

qualified service

technician to prevent personal injury or damage to the machine.

7. Disconnect power to the washer at the circuit breaker or

fuse box, or unplug the machine in an emergency when

servicing is required. Have the installer show you and label the

proper switch or fuse at the electrical disconnect box.

Retain the shipping bolts, spacers and washers.

Should you move residence then these should be

replaced to support the inside of the machine to

prevent damage when transporting the machine.

Warning !

The company denies all liability if and when these

instructions are not respected. Plastic bags,

expanded styrofoam, nails and other packaging

parts are not children’s toys, are potentially

dangerous and should be disposed off properly.

Instructions for installation and use

www.aristonappliances.us

You should carefully position the drain hose to avoid kinks and

ensure proper drainage of the water.

The outlet end of the drain hose must be at least 25” (62 cm)

above the base of the machine. At this point it is possible for

the water to be discharged into a sink or drain pipe, but an air

break must be available at this 24” height to prevent the machine

from syphoning (see fig. aside).

No more than 6” of the drain hose should be inserted in the

drain pipe.

IMPORTANT

make sure that the drain hose is not kinked and the water flow

has not been restricted.

Standpipe drain system:

In RV installation needs a 1-1/2 inch (3.7 cm) diam.

standpipe with minimum carry away capacity of 7 gallons (31

liters) per minute or 2” (5 cm) in home installation.

Floor Standpipe drain:

Top of standpipe must be at least 25 inches (62 cm) high and

no higher than 34 inches (86 cm) from the bottom of

washer (A).

Wall standpipe drain:

25 inches (62 cm) min.; 34 inches (86 cm.) max

from end of drain hose to bottom of washer (B).

PLUMBING (Water Out)

25

2

25”

34”

Included in the accessories supplied with this machine are 2

inlet hoses and 4 rubber washers. The straight end of these

hoses should be connected to the supply fig. 1.

The 90° angled end of these hoses should be connected to

the inlet valves on the back of the machine, using one of the

washers to make a water tight seal on each connection.

The couplings should be tightened by hand, a tool should only

be used if a leak occurs. Do not use excessive force (see M,

fig. 1).

The DO NOT USE AN EXTENSION CORD.

Repair or replacement of a part should be made only by a

qualified service technician to prevent personal injury or damage

to the machine. inlet valves are color coded:

Red = Hot

White = Cold

PLUMBING (Water Inlet)

Connection to the water mains

Water pressure must range within the values indicated on the

data plate on the rear of your washer-dryer. If the water pipes are

new or left unused, then before connecting the machine run the

water until clear to remove debris. Connect the inlet hose to a

cold water tap having a ¾“ BSP thread. Ensure that there are

rubber washers are at each end of the inlet hose. The L-Shaped

end goes on the machine and straight ends on the water faucets

Note: Replace inlet hoses after 5 years of use to reduce the

risk of hose failure. Record hose installation or replacement

dates on the hoses for future reference.

Periodically inspect and replace hoses if bulges, kinks, cuts,

wear or leaks are found.

Fig. 1 - Water pipe inlet at the top right

7

Instructions for installation and use

www.aristonappliances.us

* Additional clearances

for wall, door and floor

moldings maybe required.

Minimum

installation

spacing

** Additional space

is needed when an

external exhaust

elbow is used

.

8

What goes in your washer-dryer ?

Before washing, you can do a great deal to ensure better results. Divide your

garments according to fabric and color. Read the labels, follow their guidelines.

LAUNDRY PREPARATION

Sorting

Clothes should be sorted from separate items which could

damage other garments. Sort items into loads according to

similar colors, fabrics, garment construction and degrees of

soil.

- Color. Separate clothes into three groups: whites and pastels,

medium and bright colors and dark colors. Items which bleed

color should be washed alone.

- Type of fabrics. Delicate items should be separated from

sturdier items. Fabrics that shed lint should be separated

from those which shed none or attract lint.

- Garment constructions. Garments that may fray easily or

that have unusual trim require gentle care. These garments

may be washed in the loader using the knit cycle. If garments

are fragile and delicate, hand washing may be desirable.

- Degree of soil. Heavily soiled items should be separated

from the rest of the wash to prevent transfer of soil in the wash

water.

Inspection

While sorting clothes into wash-loads, also inspect each

garment to see if it requires special care.

- Remove stains, while they are fresh and easy to get out. Try

cold water first to remove unknown stains. Hot water sets stains

containing protein such as blood, egg, meat and milk. To remove

difficult stains, refer to the removal Chart at the end of the

manual.

Pretreating

Pretreat heavily soiled areas such as collars, cuffs and center

of pillowcases by using a prewash spray, or brushing liquid

detergent or a laundry detergent or a laundry detergent and

water paste over the areas before washing.

M

Dividing your

garments according to

fabric and color, is

very important for

good results

Operating instructions

- Pretreat heavily soiled areas such as collars, cuffs and

centers of pillowcases. Refer to the “Pretreating” section for

specific instructions.

- Mend rips and tears, before washing, so further damage is

not done to garments.

- Empty pockets. Objects left in pockets such as crayon,

pens or markers, or tobacco crumbs may stain an entire wash

load. Paper tissues will shred leaving bits on each item in the

washer. Remove coins and other foreign objects to prevent

damage to the machine.

- Fasten all hooks, zippers and buttons.

- Turn knit garments wrong side out to reduce the tendency

of knits to “pill”. Fabric “pills” are balls of fibers on the surface

the garments caused by wear or friction.

- Remove loose dirt and sand. Brush dirt from trouser cuffs;

shake or vacuum rugs to remove loose surface soil.

- If buckle is washable, place a scrap of material securely

around the ornament before washing and drying to prevent

scratching and damage to the machine. Remove non-washable

trims, buckles, buttons and belts.

- Tie strings, belts and apron sashes into bows to avoid

tangling during washing.

- Before loading the washer, make sure the drum is empty.

The machine may be installed in a recessed area,

closet or alcove.

The installation spacing is in inches and is the

minimum acceptable.

Additional spacing should be considered for easy

inastallation, servicing and in compliance with local

codes or ordinances.

Other installation must use the minimum dimensions

indicated .

RECESSED, CLOSET AND ALCOVE INSTALLATION

(Instructions)

Instructions for installation and use

www.aristonappliances.us

Refer to the Stain Removal Chart for treatment of specific stains.

If an entire item is heavily soiled or very stained, it may be both

easier and more effective to prewash the item before laundering

than to pretreat every spot.

Prewashing

Prewash excessively soiled clothes, such as work or children’s

clothes.

They often get very soiled. Prewashing with detergent will help

loosen the soil.

Laundry aids

Detergents are the most popular cleaning agents for home

laundry.

Using too little detergent results in poor wash quality, while

using too much causes excessive suds and poor rinsing.

Detergents not only remove soil, but also hold it in suspension

in the wash water to prevent redepositing it on the wash load.

The amount to use depends on wash load size, amount of soil,

water hardness and detergent type.

ALWAYS measure the amount of detergent. The amount

of suds formed is not necessarily an indication of how much to

use. Some detergents form a great amount of suds, others

only a few. Use only detergents suitable for front loading

washers.

LAUNDRY AIDS

1. Use only low sudsing detergent.

2. The degree of soil will change detergent amounts. For heavier

soiled loads, increase the amount of detergent used.

3. If water is extremely hard, detergent should be increased.

Less detergent should be used in soft water.

4. If garments have been pretreated, decrease the amount of

detergent. If garments have ben heavily pretreated, it may not

be necessary to add detergent.

5. If the previous machine owned was a top loader, the initial

washloads in a front loader may require a reduced quantity of

detergent until the detergent remaining in the clothes is

removed. Old detergent trapped in the garments will be released

during the tumble action wash cycle.

For quantities of detergent to be used, refer to the detergent

manufacturer’s instructions on the box.

Detergent will be flushed automatically into the machine from

the detergent dispenser. The suds level should never rise more

than halfway up to the porthole. Too much foam will not impede

the wash action of your machine but will rise through the

detergent dispenser and make a mess on the floor !

If this should happen clear excessive suds by setting the

timer to the beginning of the first rinse and allow the

machine to rinse out.

Bleaches

Bleach functions to whiten clothes, remove certain problem

stains, to deodorize and in some cases to sanitize; however

bleaching is not a substitute for good laundry techniques. Bleach

should never be added to the rinse water. Always dilute bleach

before using.

To add bleach, open detergent dispenser door and pour in

compartment 4 (see page 15 and 13-14).

WARNING:

Under no circumstances overfill the bleach dispenser. Excessive

bleach will run directly into the machine and may possibly

damage the clothes.

Fabric Softener

All fabrics, particularly towels, benefit from the use of fabric

conditioners in the final rinse. Items of laundry feel softer, are

more easily ironed and the clinging affect of synthetics is

considerably reduced.

Pour the softener into “Additives” compartment of the detergent

dispenser to the level indicated on the syphon. Under no

circumstances overfill, as the softener will immediately syphon

into the machine and in so doing, impair the wash results.

Starting the washer-dryer

After installing your new washer-dryer, start a wash cycle by setting a desired program .

always check that:

1. The door is closed

correctly.

2. The plug is secured in the

socket.

3. The water supply is turned

on.

Choose the desired program

The program is selected

according to the type of

garments that need to be

washed. To choose a program,

refer to the table on page 11,

then:

1) turn Washer knob until the

selected program is aligned

with the mark on the knob,

2) turn Dryer knob to the

desired position,

3) Set the Wash Temp knob to

the appropriate Wash/Rinse

temperature settings,

4) if necessary use buttons F,

G, H, I and lastly, press the

Power button.

5) Remember that, if you want

to use it, the "Delay Timer"

should be set before

the wash cycle.

At the end of the wash cycle...

Mode+Door Lock light will

flash fast for a few seconds,

and then flashes slowly.

Then turn the washer-dryer off

by pressing Power button

(O position). You can now

open the washer-dryer door

safely. After having removed

the freshly cleaned laundry,

leave the door open to allow

air circulation inside the drum.

Remember that, in the event

of a power failure, or should

the washer-dryer switch

itself off, the program chosen

will remain in memory.

Starting your washer-dryer in

the right way is important for

the quality of your wash, to

help prevent future problems

and enhance life expectancy

of your appliance. Once you

have loaded your washer-

dryer and added the detergent

together with any fabric

conditioner,

For more delicate

garments:

protect underwear, tights

and stockings and

delicate items by placing

them in a canvas pouch

9

Instructions for installation and use

www.aristonappliances.us

I

G

L

F

E

H

N

M

A

B

C

D

Temperature control knob

It is used to set the wash tem-

perature in the recommended

program table on pg. 11. It also

allows you to reduce the tem-

perature recommended for the

selected program, and even to

set a cold wash cycle.

ON-OFF (Power)

To turn on the washer-dryer,

press button L in. To turn off,

press button I again so that it

is out.

Turning the appliance off

does not cancel the selected

program.

On-Off lamp -

Door lock (Status)

Lamp M flashes slowly when

the appliance is switched on

and awaiting instructions and

at the end of a cycle, indicating

that the door can be opened. It

flashes quickly when the door

should not be opened. A

steady light means the

appliance has accepted the

selected programme.

Drying cycle lamp

When this lamp is on, it means

that knob C has been set on a

drying cycle and at the end of

the wash cycle, the appliance

will run the selected tumble

drying cycle.

Easy iron

This function allows your

clothes to come out of the

machine without wrinkling,

making it much easier to iron.

You can use it with

Permanent Press and Hand

Washables programs.

Press this button in such

programs and the wash cycle

will come to a stop on one

position Easy iron.You can

complete the cycle by pressing

button H again.

Dry Time knob

This control allows you to

preset the drying time you want

according to your require-

ments which may be “damp

dry” ready for ironing, or “bone

dry” ready for putting away. For

more details see the drying

time table on page 12. After all

the controls have been

correctly set, the dryer will start

to operate as soon as you close

the door.

Washer knob and Delay

start

Use this knob to select the

wash program.

Turn this knob clockwise only.

To select a program, you should

turn the knob so that the word/

number of the desired program

is in line with the pointer on the

knob.

Now press on/off button L

(position I), pilot lamp M will

start flashing.

After 5 seconds, the setting will

be accepted, pilot lamp M will

stop flashing (staying lit) and the

wash cycle will begin.

If you want to interrupt the

program in progress or set a new

one, select one of the

Reset

positions and wait 5 seconds.

When the cancellation has

been accepted, pilot lamp will

flash 5 times, and you can then

turn the appliance off.

You can use this knob to delay

the appliance's operation.

Select one of the 4 delay time

positions, press the on/off

button L in and wait 5 min. The

setting has now been accepted

(pilot lamp M stays lit) and you

can select the program you

desire.

Pilot lamp M has a particular

flashing motion (2" on and 4"

off) to indicate that a delayed

start has been set.

During this phase, you can

open the appliance door and

change the washing load,

should you wish to do so.

After the wash cycle has been

set and accepted by the

washer-dryer, turning the knob

will have no effect (except for

when it is on position Reset

(Stop).

Detergent dispenser

It is divided into 3+1 sections:

1. Detergent for pre-wash;

2. Detergent for the main

cycle wash;

3. Fabric conditioner;

4. Bleach.

Here I’m in control

Extra Rinse

This function adds one rinse

cycle for Cotton and

Permanent Press fabrics.

Use of this function is

recommended for improving

rinsing results when washing

full loads and large quantities

of detergent are used.

Recommended in case of

detergent contact allergies.

Low Spin

Use this button to reduce the

spinning speed from 1200 to

600 rpm for the cotton and

linen programs and from 850

to 450 rpm for the Permanent

Press fabrics programs.

The detergent dispenser with

the additional bleach

compartment is here.

(For details see page 15).

Knobs are hidden.

Just press them lightly in the

middle to extract them.

Making the right choice is important. And its easy.

Program key to consult a

straightforward chart of the

different programmes availa-

ble: pull the grey tab outwards

to open it.

Pre-wash

With this button, you can pre-

wash on all programs except

the Wool program. (see page

11).

Note: If you run a dry cycle,

pressing this button the

machine will not carry out the

easy iron function.

MAX

1

2

4

3

10

Instructions for installation and use

www.aristonappliances.us

11

IMPORTANT: TO CANCEL THE WASH PROGRAM YOU HAVE JUST SET, SET THE

WASHER KNOB TO THE “RESET” POSITION AND WAIT FOR AT LEAST 5 SECONDS.

The data found in the table are purely indicative, and can vary according to the quantity and type of washing, the water system

temperature and the room temperature.

Notes.

For the anti-crease function: see Easy iron, opposite page. The information contained in the table is purely indicative

Type of fabric and degree

of soil

Program

knob

Wash temperature

knob

Pre-wash Detergent

for wash

Fabric

softener

Bleach Length of

the cycle

(minutes)

Description of wash

cycle

DELAY TIMER

12h 9h 3h 1h

12 - 9 - 3 - 1 hour delay Start is delayed by 12 - 9 - 3 - 1 hours

Stop/Reset

Interrupts/Cancels the selected program

COTTON

Exceptionally soiled whites

(sheets, tablecloths, etc.)

1

Heavy

KKKK

90

Wash cycle

, rinse cycles, intermediate and

final spin cycles

Heavily soiled whites and fast colors

2

Regular

KKKK

50

Wash cycle ,

rinse cycles, intermediate and

final spin cycles

Slightly soiled whites and delicate

colors

(shirts, jumpers, etc.)

3

Light

KKKK

40

Wash cycle ,

rinse cycles, intermediate and

final spin cycles

Rinse cycles

K

25

Rinse cycles, intermediate and final spin cycles

Spin cycle

13

Draining and final spin cycle

Drying cycle for cotton fabrics

Drying

Stop/Reset

Interrupts/Cancels the selected program

PERMANENT PRESS

Heavily soiled fast color synthetics

(baby linen, etc.)

4

Heavy

KKK

80

Wash cycle ,

rinse cycles, Easy Iron or

delicate spin cycle

Delicate color synthetics

(all types of slightly soiled garments)

5

Regular

KKK

65

Wash cycle ,

rinse cycles, Easy Iron or

delicate spin cycle

Delicate color synthetics

(all types of slightly soiled garments

)

6

Light

KKK

40

Wash cycle ,

rinse cycles and delicate spin

cycle

Rinse cycles

K

25

Rinse cycles, Easy Iron or delicate spin cycel

Spin cycle

10

Draining and delicate spin cycle

Fabric softener

K

Rinse cycles with automatic introduction of

softener, anti-crease or delicate spin cycle

Drying cycle

Drying

Stop/Reset Interrupts/Cancels the selected program

HAND WASHABLES

Delicates

7

Light

KKK

64

Delicates ,

rinse cycles, Easy Iron or

draining

Silk

, particularly delicate garments

and fabrics

(curtains, silk, viscose, etc.)

8

Silk

KKK

60

Wash cycle ,

rinse cycles, Easy Iron or

draining

Wool

9

Wool

KK

45

Wash cycle ,

rinse cycles and delicate spin

cycle

Rinse cycles

K

Rinse cycles, Easy Iron or draining

Spin cycle Draining and delicate spin cycle

(Silk excluded)

Drain Draining

Drying cycle for hand washables

Drying

Stop/Reset

Interrupts/Cancels the selected program

A program for all seasons

What are you washing today?

Instructions for installation and use

www.aristonappliances.us

Fabric

type

Load

type

Max.

load

Lbs

(kgs)

Extra

Dry

Ward-

robe

Iron

- Cotton,

- Linen

C lothing of

different

sizes

8

(3.5)

100 90 80

- Cotton

Terry

towels

8

(3.5)

100 100 90

- Cotton

Sheets,

Shirts

5

(2.5)

80 70 60

-Acrylics

Pyjamas,

socks, etc.

2

(1)

60 50 50

- Nylon

Slips, tights,

stockings,

etc.

2

(1)

60 50 50

How to dry

- During the drying phase, the door tends to get

quite hot.

- Do not use the appliance to dry clothes that have

been washed with flammable or chemical

solvents (e.g. trichlorethylene).

- Do not use the appliance to dry foam rubber or

similar elastomers.

- Make sure that the cold water faucet is turned

on during the drying cycles.

- This washer-dryer can only be used to dry clothes

which have been pre-washed in water.

WARNING

Useful tips

Never use your washing

machine to wash... torn, fraying

or non-hemmed linen. If it is

absolutely neccessary, place it

in a bag for protection. Do not

wash colored linen with whites.

Watch the weights !

For best results, do not exceed

the weight limits stated below

(figures show weight of dry

garments):

- Resistant fabrics:

12 lbs(5.5 kg) maximum

- Synthetic fabrics:

6 lbs 10 oz (3 kg) maximum

- Delicate fabrics:

5 lbs 8 oz (2.5 kg) maximum

Denim Alert.

Some overalls have straps with

hooks that can damage the

drum of your washing machine

or other garments during the

wash. To minimize the risk,

place hooks in the pocket and

fasten with safety pins.

Vacations: unplug the

appliance.

It is recommended that you

should unplug the machine from

the socket and turn off the water

supply. Leave the door ajar to

allow air circulation to the draw

and the door gasket area. This

will prevent unpleasant odours.

Combined (Wash&Dry)

• Look at table A to the side

and follow the instructions

provided for MAX load to have

an automatic washing and

drying cycle.

• Follow the instructions for

wash only (see page 9, the

section "Starting the Washer-

Dryer")

• Set the dryer time on Dryer

knob.

• Press the Power button.

If the laundry load to be

washed and dried exceeds

the maximum load (see table

A), then:

- follow the instructions

provided for wash only (page

9, in section "Starting the

Washer-Dryer" and follow

these instructions.

- when the wash cycle has

finished, remove your

washing, divide it up and

replace part of it inside the

drum.

Now follow the instructions

provided for a dry only cycle.

Repeat this procedure for the

remainder of the load.

Dry only

• Load the clothes no more

than 2/3 full (8 lbs/3.5 kg) for

cottons, (see table for other

fabrics), make sure that:

- the door is shut correctly;

- the plug is inserted in the socket;

- the water tap is turned on;

- Power button has not been

pressed (O position).

• Set the Washer knob to the

appropriate “OFF” setting

depending on the type of fabric

• Set dryer time on the Dryer

knob

• Press Power button to start.

When Drying is Complete...

Mode+ Lock light flashes

slowly. Turn the washer-dryer

off by pressing the Power

button (O position). Wait

approximately one minute

before opening the door. Once

you have removed the dry

clothes from the appliance,

leave the door open or ajar to

avoid the formation of bad

odors and turn off the water (if

attached with a faucet adapter

kit.)

The data contained in the table are purely indicative.

The drying time depends largely on the type of material (some

fibers absorb more water than others), on the dampness of the

articles when the drying is started and on the amount of the

laundry. Table napkins, towels and similar (rather thick) articles

will take a long time to dry.

A combined Washing and Drying Program

For more delicate

garments:

protect underwear,

tights and stockings

and delicate items by

placing them in a

linen bag

For cotton loads of less than 2 lbs (1 Kg), use the drying

program designed for synthetic fabrics.

A spin cycle is carried out during the drying if you have

set a cotton program .

IMPORTANT

For best results, we

recommend you use very

little detergent, taking care

not to wash more than

3 lbs (1,5 kg) of laundry.

WOOL CYCLE

Table A.

Drying time (minutes)

- Pure new wool:

3 lbs(1,5 kg) maximum

- Bathrobe:5 lbs 8 oz (2.5 kg)

maximum

How much does it weigh?

1 sheet 11/4 lb (400-550 gr.)

1 pillow case 4 oz.(120 gr.)

1 tablecloth 1 lb (450 gr.)

1 bathrobe 2-3 lbs

(900-1,300 gr.)

1 towel 5

oz/1 lb (150-500 gr.)

Colored T-shirts, printed ones

and shirts last longer if turned

inside out before washing.

Printed T-shirts and sweatshirts

should always be ironed inside

out.

12

Instructions for installation and use

www.aristonappliances.us

Blood

Rinse or soak fresh stain in cold water. Work detergent into any

remaining stain. Rinse. If stain persists, put a few drops of ammonia

on stain and repeat detergent treatment. Rinse. If necessary bleach.

Candle Wax

Scrape off excess. Place stain between clean white blotters or several

layers of facial tissues. Press with warm iron. Sponge with cleaning

fluid. If dye spot remains, bleach.

Ketchup

Scrape of excess. Soak in cold water 30 minutes. Pretreat with a

detergent paste. Launder.

Chewing Gum

Rub with ice to harden. Scrape off excess with dull blade. Sponge

with cleaning fluid.

Chocolate or Cocoa

Soak 15 minutes in cold water. Rub detergent paste into stain, then

rinse thoroughly. Launder in hottest water safe for fabric. If colored

stain remains, sponge with hydrogen peroxide, rinse and launder.

Cod liver Oil

Sponge article with cleaning fluid. Soak in warm suds. If stain

persists, wash with bleach safe for fabric. To remove yellow stain,

sponge with hydrogen peroxide. Rinse and launder. Old stains

may be nearly impossible to remove.

Coffee or Tea (Black)

Soak fresh stains immediately in cold water. Then use bleach

treatment with hottest water safe for fabric. Or if safe for the fabric

pour boiling water through spot from a height of 1 to 3 feet. Launder.

Coffee or Tea (With Cream)

Rinse or soak in cold water. Work detergent into stain. Rinse. Dry. If

grease stain remains, sponge with cleaning fluid. Repeat, if

necessary. If stain remains, bleach.

Cosmetics: eye shadow, lipstick, liquid make-up,

mascara, powder, pancake make-up or rouge

Apply undiluted liquid detergent to stain, or dampen stain and rub

in soap or detergent paste until thick suds are formed. Work in until

stain is gone, rinse well. Repeat if necessary. If color remains,

bleach if safe for fabrics.

Cream, Ice Cream or Milk

Sponge stain with cool water or soak stain in cool water for 30

minutes or longer. If stain remains, work a detergent in- to spot then

rinse. Bleach if necessary.

Deodorants and Antiperspirants

Wash or sponge stain thoroughly with warm water and de- tergent;

rinse. If stain remains, bleach with hot sudsy water. Launder. You

may be able to restore fabric color by sponging with ammonia.

Rinse thoroughly.

Dye

Rinse or soak in cold water. Work detergent into stain. Rinse. If

necessary, bleach. Stain is not always possible to remove. A

commercial color remover may also be used.

Egg or Meat Juice

Rinse in cold water. If stain remains, sprinkle with meat tenderizer,

let stand 15-20 minutes. If stain still remains, sponge with cleaning

fluid or diluted bleach. Launder in hot water. The use of hot water

first may set stain.

Stain Removal Chart

Fabric Softener Stain

Rub with bar soap until stain has lightened. Rinse thoroughly.

Launder. Rubbing alcohol is sometimes effective in the color of

the garment can take it. Launder. If desired, dry cleaning can be

used.

Felt tip pen

Spray spot with cleaners suitable to this purpose. Sponge stain

thoroughly. Rinse with cold water. Reapply cleaner if necessary .

Fruit, Wine

Soak fresh stains immediately with cool water. Then use bleach

treatment with hottest water safe for fabrics, pour boiling water

through spot from a height of 1 to 3 feet. Launder.

Grass

Work detergent into stain. Sponge with denatured alcohol. Bleach,

if necessary.

Grease or Oil

Scrape away excess. Rub detergent paste or a general pur- pose

liquid household cleaner into stain, rinse with hot water. If stain

remains, sponge thoroughly with a grease solvent. Dry. Repeat if

necessary. To remove yellow stain, use a chlorine or oxygen

bleach.

Ink. Ball-point

Same ball-point inks are set by water. First test a scrap of cloth.

Sponge stain repeatedly with acetone, amyl acetate or rubbing

alcohol. Hair spray is effective. Launder. Bleach if necessary.

Use amyl acetate on triacetate, arnel, dynel and verel. Use

acetone on other fabrics.

NOTE: Some inks cannot be removed.

Mildew

Brush off surface growth to keep mold spores from spreading.

Dip article into solution of 1/2 cup bleach per 1 gallon of cool

sudsy water for 5 to 10 minutes. Rinse well. Launder.

Mud

Let stain dry; then brush well. Rinse repeatedly in cool water until

mud comes out. Launder. (Hot soaps suds set a red or yellow

clay stain).

Mustard

Soak in hot detergent water for several hours. If stain remains,

bleach.

Nail Polish

Treat while fresh, scraping or wiping off as much as possi- ble,

before it dries. Place stain face down on white paper towels.

Sponge back of stain acetone (nail polish remover) or sponge

with denatured alcohol and a few drops of household ammonia.

Sponge stain frequently. Launder with water at temperature

suitable for fabric.

Do not use acetone on acetate, arnel, dynel or rayon.

Paint

Sponge or soak in turpentine or solvent recommended as a

thinner on label. Launder.

Perfume

Rinse in cold water. Rub undiluted liquid detergent or a detergent

paste into stain. Rinse. If stain remains, bleach.

13

Instructions for installation and use

www.aristonappliances.us

Permt Press/

wrinkle resistant

Delicate/

Gentle

Normal/

Cotton Heavy Duty

Water Temp.

Machine Wash

Cycle

Tumble

Dry

Special

Instructions

Bleach

Symbols

Normal/

Cotton Heavy Duty

Permanent Press/

wrinkle resistant

Do not washHand wash Do not wring

Hot

(50

o

C/120

o

F)

Warm

(40

o

C/105

o

F)

Cold/Cool

(30

o

C/85

o

F)

Dry Do not

tumble dry

Do not dry

Line dry/

hang to dry

Drip dry Dry flat In the shade

Any bleach

(when needed)

Only non-chlorine bleach

(when needed)

Do not bleach

Delicate/

Gentle

UNDERSTANDING FABRIC CARE LABELS

The symbols on labels of your garments will help you in choicing the suitable wash program, the right temperature,

wash cycles, and ironing methods. Don’t forget to give a glance to these useful indications !

Look,

...and select

the right

temperature !

14

Perspiration

Wash or sponge stain thoroughly with warm water and detergent

paste. If perspiration has changed the color of the fabric, restore it

by treating with ammonia or vinegar. Apply ammonia to fresh stains;

rinse with water. Apply vinegar to old stains; rinse with water.

Rust and Iron

Apply commercial rust remover, according to manufacturer’s

directions. Rinse. Or, if safe for fabric, boil stained article in solution

of 4 teaspoons of cream of tartar to 1 pint water.

Scorch

Rinse or soak in cold water. Work detergent into stain. Rinse.

Bleach, if necessary. Stain may be impossible to re move.

Urine

Soak in cool water. If stain is dry, work a detergent paste into the

spot then rinse. If necessary, bleach.

Shoe

Polish Scrape off as much as possible. Pretreat with a detergent

paste; rinse. If stain persists, sponge with rubbing alcohol (1 part

to 2 parts water) or turpentine. Remove turpentine by sponging

again with warm detergent solution or with alcohol. Bleach if

necessary.

Soft Drinks

Sponge with cold water, some stains are invisible when they have

dried, but turn brown when heated and may be impossible to

remove.

Tar and Asphalt

Act quickly before stain is dry. Sponge with grease solvent or

turpentine. Launder.

Instructions for installation and use

www.aristonappliances.us

Useful tips about the detergent dispenser

It’s important for a good wash

The first secret is the easiest: the detergent dispenser is opened by pulling it out.

The detergent dispenser can

be removed and cleaned: pull

it outwards, as indicated in the

figure. Then leave it under

warm running water for a few

minutes.

Detergent dispenser

cleansing

1

2

In compartment

1:

Detergent for pre-washing

(powder)

In compartment

2:

Detergent for washing

(powder or liquid)

In compartment

3:

Additives (softeners,

perfumes, etc.)

In compartment

4:

Bleach and delicate bleach.

MAX

1

2

4

3

Cutting costs efficiently

A guide to environmentally friendly and economic use

of your appliance.

MAXIMISE THE LOAD SIZE

Achieve the best use of energy, water, detergent

and time by using the recommended maximum

load size.

SAVE up to 50% energy by washing a full load

instead of 2 half loads.

DO YOU NEED TO PRE-WASH?

For heavily soiled laundry only!

SAVE detergent, time, water and between 5 to

15% energy consumption by NOT selecting

Prewash for slight to normally soiled laundry.

IS A HOT WASH REQUIRED?

Pretreat stains with stain remover or soak dried

in stains in water before washing to reduce the

necessity of a hot wash programme.

SAVE up to 50% energy by using a 60°C wash

programme.

BEFORE USING A DRYING PROGRAM ...

SAVE energy and time by selecting a high spin

speed to reduce the water content in laundry

before using a drying programme.

15

Bleach cycle and stain

removal button

If bleaching is necessary, the

extra case 4 (provided) must

be inserted into compartment

1 of the detergent dispenser.

When pouring in the bleach,

be careful not to exceed the

"max" level indicated on the

central pivot (see illustration).

The use of the additional

bleach container excludes

the possibility of using the

pre-wash cycle.

Traditional bleach can only be

used on sturdy white fabrics,

whereas delicate bleach can

be used for colored fabrics,

synthetics and for wool.

You cannot bleach with the

“Silk” program.(See page 11).

NOTE: BLEACH ONLY WORKS

WITH HOT WASH TEMP.

MAX

You must follow the quantity

recommendations provided by

the manufacturers when

adding detergent or fabric

softener. Quantities will vary

according to the wash load, the

water hardness and how soiled

the clothes are.

Experience will help you select

the right quantity almost

automatically.

Before adding detergent for

pre-washing in compartment

1, make sure that the extra

compartment for bleach 4 has

not been inserted.

Ensure no overfilling when

adding fabric conditioner in

compartment 3.

The washing machine automa-

tically adds the softener to the

wash in each program.

Liquid detergent is poured into

compartment 2 just a few

seconds before starting the

wash cycle.

Remember that liquid

detergent is only designed for

wash cycles of up to 60

degrees on non pre-wash

items.

Special containers are sold

with liquid or powder deter-

gents for placing inside the

washing machine drum, these

are positioned according to the

instructions found in the

detergent box

Never use hand wash deter-

gent, because it may form too

much foam, which could da-

mage the washing machine.

Detergents that are specifically

formulated for both hand and

machine wash are an excep-

tion.

One last secret: when washing

with cold water, always reduce

the amount of detergent you

use: it dissolves less easily in

cold water than in hot water, so

part of it would be wasted.

Instructions for installation and use

www.aristonappliances.us

The washer-dryer fails

to fill with water.

Is the hose correctly

connected to the tap?

Is there a water shortage ?

There could be work in

progress in your building or

street.

Is there sufficient water

pressure? The autoclave

may be malfunctioning.

Is the tap filter clean? If the

water is very calcareous, or

if work has recently been

carried out on the water

piping, the tap filter could be

clogged with particles and

debris.

Is the rubber hose kinked?

The rubber hose bringing

water to washer-dryer must

be as straight as possible.

Make sure it is not squashed

or kinked.

The Washer knob

keeps turning?

Wait a few minutes for the

drain pump to empty the

tub, switch the washer-dryer

“I only want an authorised

specialised technician

with original

Ariston spare parts!”

off, select one of the

positions stop/Reset , then

switch it back on. If the knob

continues to turn, call for

assistance because it is

showing an anomaly.

The washer-dryer

continuously fills and

drains water.

Is the drain hose positioned

too low? It must be installed

at a height ranging from 25”

to 34” (62 to 86 cms.).

Is the end of the hose

immersed in water?

Does the wall drainage

system have a breather

pipe? If the problem persists

even after these checks, turn

the water supply off the

machine and call for

assistance.

If you live on an upper floor

of your building, there may be

a problem with your drain

trap.

To solve this problem, a

special valve must be

installed.

Before calling, read the following

Troubleshooting

In most cases, when your washer-dryer fails to work, the problems arising can be easily solved

without having to call for a technician. Before calling for assistance, always check these points.

The washer-dryer fails

to start.

Is the plug correctly inserted

into the socket? It could have

been moved while cleaning.

Is there electricity in the

house?

A circuit breaker may have

switched off as a result of too

many electrical appliances

working at the same time. Or

maybe due to a general failure

in your entire area.

Is the washer-dryer door

closed properly?

For safety reasons, the

washer-dryer cannot work if

the door is open or not shut

properly.

Is the On/Off button

pressed?

If it is, then a program has

been set.

Is the Washer knob in the

correct position for those

models concerned?

Is the water supply turned

on? For safety reasons, if the

washer-dryer does not load

water, it cannot start a wash

cycle.

Simple: with the new Ariston technology, you need less

than half of it, to get good results on twice as much!

This is why you cannot see the water through the door:

because there is little, very

little of it, to respect the

environment yet without

renouncing maximum

cleanliness.

And, on top of that, you are

also saving electricity.

But where did all the water go?

You will be charged for a service call while the

appliance is in warranty if the problem is not

caused by defective workmanship or materials.

RIGHT WRONG

Turn off the water

supply after use.

This will eliminate

the possibility of

leakage.

Always leave the

appliance door ajar to

avoid bad odours.

Clean the appliance’s

exteriors gently.

To clean the

exteriors and the

rubber parts of the

appliance, always use

a soft cloth dipped in

warm and soapy

water.

Leave the washing machine plugged

in while cleaning.

Even during maintenance, the

appliance should always be un-

plugged.

Use solvents and aggressive

abrasives.

Never use solvents or abrasives to

clean the external and rubber parts

of the washing machine.

Neglect the detergent dispenser.

It is removable and can easily be

cleaned by leaving it under running

water.

Go on holiday without thinking about

her.

Before leaving, always make sure

that the washing machine is un-

plugged and that the water supply is

turned off.

16

Instructions for installation and use

www.aristonappliances.us

ZZZZ...

Too much foam.

Is the detergent appropriate

for machine washing? Check

whether the definition on its

label reads “for machine wash”

or “hand and machine wash”,

or any other similar wording.

Is the correct amount being

used? An excessive amount of

detergent, besides producing

too much foam, does not

guarantee a more effective

wash, and causes scaling in the

internal parts of the appliance.

The washer-dryer

does not dry.



Check whether:

the plug has been correctly

inserted into the socket; there

is electricity in your home; the

appliance door has been shut

properly; a delayed start (if

available) has not been

selected; program knob A

has been set to Reset and

the drying cycle knob C has

been set to position

0 minutes.

The washer-dryer doesn't

dry properly.



Check whether:

1) the end of the drain hose

is underwater; 2) the drain

pump is obstructed; 3) the

advice given on the maxi-

mum loads has been taken;

4) the water tap has been

turned on.

If, despite all checks, the

washer-dryer fails to function

and the problem persists, call

your nearest authorized

Customer Service Centre,

1-800-426-0825 providing the

following information:

- the nature of malfunction

- the model type no. (Mod. ....)

- the serial number (S/N ....)

This information can be found

on the data plate situated at the

back of the washer-dryer.

Is there space between the

machine and adjacent

units? If it is not a built-in

model, the washer-dryer will

oscillate a bit during the spin

cycle. A few cm of space

should therefore be left

around it.

The washer-dryer

leaks.

Is the metal ring of the inlet

hose properly attached?

Turn off the water supply,

unplug the appliance and try

tightening its attachment

without forcing it.

Is the detergent dispenser

obstructed? Remove and

wash it under tap water.

Is the drain hose well

attached? Turn off the water

supply, unplug the

appliance and try tightening

its attachment.

Is the drain hose kinked?

The drain hose must be as

straight as possible. Make

sure the drain hose is not

crimped or kinked.

Is the washer-dryer’s drain

hose clogged? Is there an

extension of the drain hose?

If so, is it positioned

incorrectly, blocking the

water flow?

Excessive vibration

during the spin cycle.

Have all shipping bolts

been removed during

installation? See the

following page on

installation procedures.

Has the washer-dryer been

levelled correctly? The

levelling of the appliance

should be checked

periodically. Adjust the feet

and check them with a level.

The washer-dryer

does not drain or

spin.

Does the selected program

incorporate water drai-

ning? Some programs stop

at the end of the wash cycle

and draining will have to be

selected manually.

Is the “Easy iron" function

-where provided - enabled?

This function requires

manual selection for

draining.

Is the drain pump clogged?

To check it, turn off the water

supply, unplug the washer-

dryer and follow the

instructions on page 18, or

call technical support.

17

Drain: to avoid flooding

be careful to the adjust the drain

hose to at least

25” above the base

of the appliance.

Fasten the hoses securely.

Cleaning Filters

Remove filters

using tweezers,

clean and replace

Remove

filters, clean

and replace

Tape

Always get

assistance from

authorized service

agent and always

insist on original

spare parts.

Instructions for installation and use

www.aristonappliances.us

18

When in need, check the pump and the rubber hose.

The washer-dryer comes equipped with a self-cleaning pump that does not require any cleaning or maintenance. Small

objects may accidentally fall into the pump: coins, hair clips, loose buttons, etc. To avoid possible damage, they are

withheld in an accessible coin trap, located at the bottom right end of the machine.

Attention: Before attempting to examine this coin trap, first ensure

that the machine has finished its program and is empty. Unplug

the machine, as with any maintenance.

To gain access, gently ease down the top of the kick plate panel at

the base of the machine with a screwdriver etc, to release it. Then

ease the top edge forward to allow it to be lifted clear (Fig. 1).

Place a shallow dish or tray below the cover of the pre-chamber to

catch any water that might be present. Open the cover by turning

it counter-clockwise (Fig. 2). When finished cleaning, ensure that

the cover is securely tightened.

Re-fit the kick plate cover by inserting the hooks on its lower edge

into the slots and ease the top edge back into position.

The water inlet hose

Check the rubber hoses at least once a year. If you see any cracks, replace the hose immediately. When you use your washer-

dryer, water pressure is very strong and a cracked tube could easily split open. Superior quality Stainless Steel hoses are

also available for purchase.

Fig. 1

Fig. 2

Your washer-dryer is a reliable companion in life. It is just as important for you to keep it in shape.

Your washer-dryer is designed

to provide reliable service over

many years. A few simple steps

will help to extend its life and

avoid problems. It is advisable

to turn off water faucets when

the machine is not in use. This

protects the hoses, etc.

If the water in your area is

hard, use a water softener

(hard water often leaves white

stains around taps or drains,

especially in bath tubs. For

more accurate information

about the type of water in the

system, call your local water

utility).

Pockets must always be

emptied, removing pins,

badges, coins, or any other

hard objects.

CLEANING THE EXTERIOR

The washer-dryer exterior

should be cleaned with a rag

dipped in lukewarm water and

soap. Do not use polish of any

kind on the plastic trim. Some

polishes contain agents which

can damage plastics.

Cleaning the interior

If you live an area where

phosphate detergents are

banned, it may be necessary

to recondition the washer

periodically. Because a non-

phosphate detergent must be

used, body oils and detergent

may accumulate in the washer

tub. This is particularly evident

in hard water areas or in

homes where heavily soiled

garments are regularly

laundered. To remove this

build-up, run the washer

through a complete cycle

using hot water and 2 cups of

a non precipitating water

conditioner. Do not add any

clothes, detergent, or other

laundry aids.

Once the accumulation has

been removed, your laundry

should be satisfactory if you

follow the preventive

suggestions in this owner’s

manual.

GENERAL MAINTENANCE

After washing is complete the

water faucets should be turned

off to relieve water pressure on

the hoses.

Wipe the inside of the door with

a soft cloth to remove any

remaining moisture.

Periodically, a thin coat of pa-

ste wax should be applied to

the inner door or the washer;

especially to the area which

is immediately next to the

door window. This will protect

the door finish from laundry

aid spills and any

discoloration which may

results of these spills.

Clear the Coin Trap

Clear the coin trap in case of

blockage. For instructions,

please read the section

below.

Never add too much

detergent.

Detergents already contain

deliming agents. Only if the

water is particularly hard, that

is, rich in lime content, do we

recommend the use of a

specific product at every

wash.

A periodical wash cycle with

a dose of a deliming product,

without detergents or

washing, may prove useful.

Never use too much

detergent or additives

because this could cause

excessive sudsing, scaling,

and possible damage to

components in your

washer-dryer.

It is important to wash

the detergent dispenser

regularly.

To prevent dried washing

powder from

accumulating, place the

dispenser under running

water for a few minutes.

Easy Care and Maintenance

Treat your machine well and it will provide

many years of trouble free service

Do not forget to empty all

pockets:

small objects can cause

serious damage to your

washer-dryer !

Use only low-sudsing deter-

gents.

Instructions for installation and use

www.aristonappliances.us

Service Contact Number

SERVICE & PARTS : (800) 426-0825

19

Model

AWD 121

Dimensions

width 23.4" (59.5 cm)

height 33.4" (85 cm)

depth 21" (53.5 cm)

Capacity ashing

: 2-12 lbs

Drying

: 2-8 lbs

Electrical

connections

voltage 120 Volt 60 Hz

(minimal working 108 volt)

maximum absorbed power 1350 W, 13 A.

Water

connections:

maximum pressure 100 psi (689.6 kPa)

minimum pressure 20 psi (137.9 kPa)

Spinning speed up to 1200 rpm

This appliance conforms with the

UL

directives

for USA and Canada

C

U

L

US LISTED

®

Technical characteristics

As a result of technological progress, the manufacturer reserves the right to make any improvements to its appliances without

giving prior notice to its clientele.

Instructions for installation and use

www.aristonappliances.us

Ultra 8 International, 3027 East Sunset Road, Suite 101, LAS VEGAS, Nevada 89120

STATEMENT OF WARRANTIES

ARISTON Clothes Washer/Dryer

The warranties provided by (Ariston) in this statement of warranties apply only to Ariston clothes washer/dryer sold to

the first using purchaser by Ariston or its authorized distributors, dealers, retailers or service centers in the United

States or Canada. The warranties provided herein are not transferable.

Length of Warranty

2 Years Full Limited Warranty from the date of installation

*

Ariston will repair or replace, free of charge, any component part that proves defective in conditions of normal home

use. Shipping and labor costs included. Waranty repair service must be performed by an authorized Ariston service

center.

3rd - 5th Year Limited Warranty on Electronics from the date of installation*

Ariston will repair or replace ree of charge, any microprocessor or circuit board that proves defective under conditions

of normal home use 3rd year through 5th year from the date of original installation, labor charges excluded.

3rd - 5th Year Limited Warranty on Motor from the date of installation*

Ariston will repair or replace free of charge, any motor or component part of the motor that proves defective under

conditions of normal home use, 3rd year through 5th year, from the date of original installation, labor charges excluded.

Lifetime Limited Warranty against Stainless Steel Rust Through from the date of installation*

Ariston wll replace your clothes dryer, free of charge, with the same model or a current model that is equivalent or

better in functionality if the washer drum should rust though under conditions of normal home use, labor, shipping, and

installation charges excluded.

10 day warranty after purchase on cosmetic damages detected

Ariston will replace any cosmetic parts, free of charge - including service call, which are detected damaged with in 10

days after purchase. Any damages deemed caused by improper handing, shipping, or installation will not be covered

under this clause.

* Date of installation shall refer to the earlier of the date the clothes washer is installed or ten business days after

delivery date.

Exlusions:

This warranty does not cover repair or service calls to correct the installation, to provide instructions on the use of

your product, to replace house fuses or correct plumbing or the electric wiring in your home. In addition any repair to

the products that’s use was in a manner other than what is normal for home use is void of any warranty claim.

The warranties exclude any defects or damage arising from accident, alteration, misuse, abuse, improper installation,

unathorized service work, or external forces beyond Ariston control, such as fire, flood, and other acts of God, or

installation not in accordance with local electric or plumbing codes. Labor, shipping, and installation charges incurred

in the repair or replacement of any product after a period of one year from the date of installation shall not be covered

by this warranty. Any and all replaced or repaired parts shall assume the identity of the original for the purposes of

the applicable warranty period. To the extent permitted by law, this warranty is in lieu of all other express and implied

warranties, including the implied warranties of merchantability and fitness for a particular purpose. Ariston does not

assume any responsibility for incidental or consequential damages.

To obtain warranty services call 1-800-426-0825, or write to:

Ultra 8 International, 2505 Anthem Village Drive, Suite E - PO BOX 562, Henderson Nevada 89052

Be sure to provide: model number, serial number, purchase date, and the sellers name and address.

Page is loading ...

Whirlpool AWD 121 (NA) Owner's manual

This manual is also suitable for

Whirlpool AWD 121 (NA) Owner's manual

in other languages

Related papers

Other documents