Impecca RA-2103ST Installation guide

Brand: Impecca

Model: RA-2103ST

Category: Freezers

Type: Installation guide

This manual is also suitable for

RA-2103W

Page is loading ...

PLEASE SAVE THESE INSTRUCTIONS. YOU MAY NEED THEM IN

THE FUTURE.

I DANGER AT

THERE IS A RISK OF FIRE: THIS REFRIGERATOR CONTAINS A FLAMMABLE REFRIGERANT. DO NOT PUNCTURE REFRIG-

ERANT TUBING.

RISK OF EXPLOSION: THE REFRIGERANT IS FLAMMABLE. UNIT MUST BE REPAIRED BY A TRAINED SERVICE TECHNICIAN

ONLY. USE CARE NOT TO PUNCTURE ANY TUBING THAT HOUSES THE REFRIGERANT.

I WARNING

ELECTRICAL INFORMATION

The refrigerator must be plugged into its own dedicated 115V, 60Hz, 15 Amp electrical outlet. Be sure not to circumvent the

grounding plug (third prong) on the outlet as it protects against electrical shock hazards.

NOTE: Keep these points in mind as well:

• Do not use an extension cord with this appliance. If the power cord is too short, have a qualied electrician or service

technician install an outlet near the appliance. Use of an extension cord can negatively aect the performance of the unit

and create a re hazard.

• Avoid plugging a refrigerator into a GFCI outlet as it may cause the outlet to trip and is NOT recommended.

• Avoid electrical outlets controlled by a wall switch.

• Avoid plugging the unit into an outlet that has insuicient power. This could damage the compressor and void the war-

ranty.

I NO USER SERVICEABLE PARTS INSIDE ANY COVERED AREA OF YOUR UNIT. TO AVOID THE RISK OF AN ELECTRICAL

SHOCK, DO NOT ATTEMPT REPAIRS YOURSELF.

I WARNING

• When refrigerator is empty, be sure to remove the doors, since it is an attractive place for children to play. This is so even

if it’s being discarded.

• Be careful to throw out any plastic aer installation that could cause a suocation hazard.

–1–

ENGLISHESPAÑOLFRANÇAIS

INTRODUCTION

Thank you for choosing this quality Impecca refrigerator. This

appliance is designed for consumer, household use. Please

carefully read this manual before using this product. Be sure to

keep the manual for later consultation.

Note: All images in this instruction manual are for indication only;

the physical appearance and options on your model may vary.

SERIAL AND MODEL NUMBER

Please record your model number and serial number below.

You can nd the number plate in the upper-le wall inside the

refrigerator.

Model Number: RA-2103

Serial Number: ______________________________

Date of Purchase: ____________________________

BEFORE DISCARDING YOUR OLD REFRIGERATOR:

• Remove the door(s), leave the shelves in place (to help

prevent children from crawling in) and have it removed

from your premises by a qualied technician.

• Check with your retailer to nd out if they’ll take away

and responsibly dispose of or recycle your old refriger-

ator.

• See www.epa.gov/rad for more information on Respon-

sible Appliance Disposal.

SAFETY NOTICES

This appliance is intended to be used in household and similar

applications such as:

• sta kitchen areas in shops, oices and other working

environments;

• individual use in hotel rooms and other residential type

environments;

INSTALLING YOUR APPLIANCE

LOCATION

When selecting a position for your unit, ensure the oor is a

at, level surface and the room is well ventilated. Avoid locating

your unit near a heat source, such as an oven, stove top, boil-

er, or radiator. Also avoid direct sunlight as it may increase the

electrical consumption.

Extreme cold ambient temperatures may also cause the unit

not to perform properly. This unit is not designed for use in a

garage or outdoor installation. Do not place any covering such

as a drape or sheet on the unit.

When installing the unit, ensure that a minimum of 3 inches of

free space is le at both sides and in the rear, and 3 inches of

space at the top of the unit. This will allow cold air to circulate

around the refrigerator and improve the eiciency of the cool-

ing process.

LEVELING THE UNIT

To level the unit, turn the two adjustable feet at the front of the

refrigerator to clockwise or counterclockwise to respectively

raise or lower the corner. If the unit is not level, the door and

magnetic seal will not function properly.

CLEANING BEFORE USE

Wipe the inside of the unit with a weak solution of baking

soda (bicarbonate). Then rinse with warm water using a damp

sponge or cloth. Wash the shelves and bins in warm soapy wa-

ter and dry completely before replacing in the unit. Clean the

exterior of the unit with a damp cloth.

If you require more information refer to the Cleaning section.

UNIT OVERVIEW & FEATURES

• Totally frost-free design

• Adjustable glass shelves

• Interior light

• Adjustable legs

• 2 liter bottle rack

• 2 fruit and vegetable storage bins

• Glass storage bin cover

• Fridge and freezer door racks

• Electronic thermostat

• Recongurable shelves

USING YOUR APPLIANCE

REFRIGERATOR TEMPERATURE CONTROL AND INDICATOR:

You will nd the refrigerator temperature control and indicator

module in the upper-middle section of your refrigerator section.

Press the SET button to adjust the temperature control between

dierent cooling temperatures ranging from 1 (cold) to 5 (cold-

est). To turn unit o, hold SET for 3 seconds.

RELATIVE FREEZER CONTROL:

The freezer also has a control knob which can be found on the

back wall of the freezer compartment. This aects the freez-

er temperature relative to the refrigerator temperature setting.

Simply turn the knob to the desired relative temperature.

NOTE FOR ALL TEMPERATURE CHANGES, ALLOW 24 HOURS

FOR FULL ADJUSTMENT.

–2–

ENGLISH ESPAÑOL FRANÇAIS

CLEANING & CARING FOR YOUR APPLIANCE

DEFROSTING

The refrigerator defrosts automatically. There is no need to do

defrost manually.

CLEANING THE INTERIOR AND THE EXTERIOR OF THE UNIT

• Remove all the shelves and the fruit and vegetable bins.

Wipe the inside of the unit with a weak solution of bak-

ing soda (bicarbonate) and then rinse with warm water

using a damp sponge or cloth. Wipe the surfaces com-

pletely dry to prevent buildup of frost before replacing

the shelves and salad bin.

• Use a damp cloth to clean the exterior, and wipe down

with standard furniture polish. Ensure sure that the door

is closed to avoid the polish getting on the magnetic

door seal or inside the unit.

• The grille of the condenser at the back of the unit and

the adjacent components can be vacuumed using a so

brush attachment.

INTERIOR ACCESSORIES

Slide one of the full size glass storage shelves into the lowest set

of guides, above the fruit and vegetable containers, and keep it

in this position. To do this, pull the storage shelf forward until it

can be tilted upwards or downwards and removed.

According to your needs, feel free to remove one or more shelves

or drawers from the unit and store them in a safe location for

later re-use.

MAINTENANCE

CHANGING THE LIGHT

Only use a 15W MAX light bulb. Disconnect power to the unit,

remove the plastic cover, unscrew the old light bulb and screw

in the new one in its place.

HANDLING / MOVING YOUR UNIT

Under no circumstances should it be lied by holding the edges

of the top area of the unit. Hold the unit around its sides or base

when moving it. .

Do not turn the refrigerator upside down, horizontally, or vibrate

the refrigerator. Do not carry at an angle greater than 45°.

NOT USING FOR EXTENDED PERIODS

When the unit is not in use for a long period of time, disconnect

it from the power supply, empty all food and clean the appli-

ance. Prop the door open somewhat with an object to avoid

unpleasant smells and the buildup of mold.

SERVICING

The unit should be serviced by an authorized technician and

with genuine spare parts. Under no circumstances should you

attempt to repair the unit yourself. Repairs carried out by inex-

perienced persons may cause injury or serious malfunction.

REVERSING THE DOOR

Only try to reverse the door hinges if you feel capable of doing

so. Ask someone to assist you during the process. If you are un-

sure if you are able to reverse the hinges, contact a qualied,

authorized technician.

TOOLS REQUIRED (NOT INCLUDED):

• Phillips screwdriver

• Flat-head screwdriver

• Hexagonal spanner

BEFORE REVERSING THE DOOR:

• Ensure the unit is unplugged and empty.

• Adjust the two leveling feet to their highest position.

• To take the door o, you will need to tilt the unit back-

wards. You should rest the unit against something solid

and block the base so that it will not slide out during the

door reversal process.

• All parts removed must be carefully put aside and re-

used to do the re-installation of the door.

• Do not lay the unit at as this may damage the coolant

system.

Parts included with Hinge Kit (packed inside unit)

Bottom Le Hinge

Le Pin Assembly (2)

Hole Plug (3)

Door Parts

Top Hinge

Top Hinge Shim

Center Hinge

Center Hinge Shim

Bottom Right Hinge

Right Pin Assembly (2)

–3–

ENGLISHESPAÑOLFRANÇAIS

STEP 1

Remove the top hinge cover. Unscrew and remove the top

hinge and top hinge shim. Keep the screws and top cap so they

can be used on the opposite side. Remove the top cap. Be sure

not to drop the freezer door!

STEP 2

Li the freezer door up and away from the appliance.

STEP 3

Unscrew and remove the center hinge and center hinge shim.

Save the screws. Li the refrigerator door up and away from the

appliance. Be sure not to drop the refrigerator door!

Pull

Center

Hinge

Center Hinge

Shim

STEP 4

Unscrew and remove the bottom right hinge. Save the

screws. Remove screw covers from opposite corner (le)

and cover exposed holes (right). Attach new bottom le

hinge with the screws removed from the opposite side.

Remove Right

Hand Hinge

(store for

future use).

New Bottom Le

Hand Hinge (found

in Hinge kit)

Remove

Top Cap

Shim

Top Hinge Top Hinge

Hinge Cover

Pull Up

–4–

ENGLISH ESPAÑOL FRANÇAIS

STEP 5

Remove right pin assemblies from the bottoms of both the

freezer and refrigerator doors. Attach the replacement pin as-

semblies on the opposite side. These can be found in the plas-

tic bag along with the User’s Manual. Use a screwdriver.

Note: Hold on to the screws as they will be needed for attaching

the new assemblies.

STEP 6

Place the refrigerator door on the bottom le hinge. Ensure that

the door is aligned horizontally and vertically. Re-attach the

middle hinge to the top (le) of refrigerator door. Attach shim to

the back of hinge, align with holes and aix to the middle beam

with the saved screws. Fasten with a screwdriver.

STEP 7

Place the freezer door on the center hinge. Ensure that the door

is aligned horizontally and vertically, and that the gasket seals

on all sides before attaching the top hinge. Attach the top hinge

and shim and place the hinge cover and top cap.

Hinge Cover

Top Hinge

Shim

Top Cap

UNIT SPECIFICATIONS

UNIT CAPACITY 9.9 cubic feet

WIDTH: (UNIT/PACKED) 24.0/26.1 (Inches)

DEPTH: (UNIT/PACKED) 26.1/26.14 (Inches)

DEPTH WITH DOOR OPEN: 47.75 (Inches)

HEIGHT: (UNIT/PACKED) 59.84/62.20 (Inches)

WEIGHT (NET/GROSS) 134.4/147.6 (Pounds)

ERROR CODES

If LED1 and LED2 are lit: Refrigerator temperature sensor error

If LED1 and LED3 are lit: Freezer defrost sensor error

If LED1 and LED4 are lit: Ambient temperature sensor error

TECHNICAL SUPPORT

Before calling technical support, please see the troubleshoot-

ing guide below. You may also visit our website at www.im-

pecca.com for answers to Frequently Asked Questions and to

Email: support@impecca.com

Phone: +1 866–954–4440

Web: www.impecca.com

Freezer

Door

Refrigerator

Door

Insert

Center

Hinge

Replace

Door

Center

Hinge

Center

Hinge

Shim

–5–

ENGLISHESPAÑOLFRANÇAIS

PROBLEM SOLUTION

My refrigerator is not getting any power no lights, no hum, etc.

Make sure that the plug is in all the way

Find another outlet. The outlet should NOT be a GFCI outlet. (A GFCI

outlet is the kind with the PUSH and RESET breaker built in, which is

common in kitchens and used only for smaller counter-top appliances).

The refrigerator’s interior light comes on but it is not cooling Check to make sure that the temperature is set cold enough. This can

depend on the environment around the unit.

Refrigerator seems to run for much longer than usual between cycles.

Make sure that the door to the refrigerator is closed all the way

Check the ambient temperature. If it’s very warm, this is normal.

If you recently put very warm food in the refrigerator, this is normal.

Make sure that the gasket around the door is free of debris. If the seal is

not tight, warm air from the environment may seep in, causing it to run

longer.

This is also normal aer being turned on for the rst time aer an ex-

tended time

Inside refrigerator temperature is too warm.

Make sure that the temperature setting is at the desired selections. See

“Using Your Appliance” for more details.

This could be caused by opening the door very oen and letting in warm

air frequently.

This can be caused by warm food

It can take at least four hours for your refrigerator to get to its target tem-

perature setting aer being o for an extended period of time.

The outside of the unit is warm This is a normal part of how a refrigerator works and is nothing to be

concerned about.

There are many dierent noises we hear emanating from the refrigerator

at dierent times, including: loud sounds when it is rst turned on; fans

running when the temperature is below 45°F; popping and/or cracking

sounds; boiling or gurgling sounds and snapping sounds.

All of these noises are typical during normal operation and cycles

There is a vibrating or rattling sounds when the unit runs. The unit may not be level. See the “Leveling The Unit” section above.

There is moisture appearing on the inside of the refrigerator walls. This can be caused by debris in the door gasket preventing a tight seal.

As well, it is a normal occurrence if the ambient air is humid. This can

also occur if the door is opened very frequently.

There is moisture appearing on the outside of the refrigerator walls. Make sure that your door is closing properly.

The light bulb stopped turning on when the door opens. Your bulb may have burned out. Replace with a 15W bulb.

TROUBLESHOOTING GUIDE

Page is loading ...

ENGLISH ESPAÑOL FRANÇAIS

–12–

VEUILLEZ CONSERVER CES INSTRUCTIONS.

ELLES POURRONT VOUS ÊTRES UTILES DANS LE FUTUR.

I DANGER AT

IL Y A UN RISQUE D’INCENDIE : CE RÉFRIGÉRATEUR CONTIENT UN RÉFRIGÉRANT INFLAMMABLE. NE PAS PERCER LA TUYAUTERIE

DE FRIGORIGÈNE.

RISQUE D’EXPLOSION : LE FLUIDE FRIGORIGÈNE EST INFLAMMABLE. L’APPAREIL DOIT ÊTRE RÉPARÉ PAR UN TECHNICIEN QUAL-

IFIÉ SEULEMENT. VEILLEZ À NE PAS PERFORER TOUT CONDUIT QUI ABRITE LE RÉFRIGÉRANT.

I AVERTISSEMENT

INFORMATIONS ÉLECTRIQUES

Le réfrigérateur doit être branché dans sa propre prise électrique de 115 V, 60 Hz, 15 ampères. Veillez à ne pas contourner la prise de terre

(troisième volet) sur la sortie, car elle protège contre les risques de décharge électrique.

REMARQUE : Gardez aussi ces points à l’esprit :

• Ne pas utiliser une rallonge avec cet appareil. Si le cordon d’alimentation est trop court, demandez à un électricien ou un tech-

nicien de service qualié d’installer une prise près de l’appareil. L’utilisation d’une rallonge peut aecter négativement les perfor-

mances de l’appareil et créer un risque d’incendie.

• Évitez de brancher le réfrigérateur dans une prise DDFT comme cela pourrait causer une défaillance et est déconseillé.

• Évitez les prises électriques commandées par un interrupteur mural.

• Évitez de brancher l’appareil dans une prise qui n’a pas une puissance nécessaire. Cela pourrait endommager le compresseur et

annuler la garantie.

I IL N’Y A AUCUN COMPOSANT SUSCEPTIBLE D’Ê TRE RÉPARÉ PAR L’UTILISATEUR À L’INTÉRIEUR DES ZONES COUVERTES

DE VOTRE UNITÉ. POUR ÉVITER LES RISQUES DE DÉCHARGE ÉLECTRIQUE, NE PAS TENTER D’EFFECTUER DES RÉPARATIONS

VOUS-MÊME.

I AVERTISSEMENT

• Lorsque le réfrigérateur est vide, assurez-vous de retirer les portes, comme il peut sembler être endroit de jeu attrayant pour les

enfants. Ceci s’applique même si vous planiez le mettre aux vidanges.

• Après l’installation, faites attention lorsque vous jetez toute matière plastique qui pourrait provoquer un risque de suocation.

Page is loading ...

Impecca RA-2103ST Installation guide

Brand: Impecca

Model: RA-2103ST

Category: Freezers

Type: Installation guide

This manual is also suitable for

RA-2103W

Download PDF

report

in other languages

français: Impecca RA-2103ST Guide d'installation
español: Impecca RA-2103ST Guía de instalación

Impecca RA-2103ST Installation guide

This manual is also suitable for

Impecca RA-2103ST Installation guide

in other languages

Related papers

Other documents