Renkforce Dual 4K Owner's manual

Brand: Renkforce

Model: Dual 4K

Category: Coffee making accessories

Type: Owner's manual

Page is loading ...

b) AC adapter

• The design of the plug-in power adapter complies with IEC Protection Class II (double insu-

lated electrical appliances). Use only a standard mains socket as the power source for the

power adapter.

• The power socket into which the power adapter is inserted must be easily accessible.

• Only use the power adapter provided to power the docking station.

• Do not pull the power adapter from the mains socket by pulling on the cable. Hold it on the

sides of the casing and pull it out of the mains socket.

• Never touch a power adapter that shows signs of damage, as this could cause a fatal electric

shock!

First, switch off the mains voltage to the socket to which the power adapter is connected

(switch off at the corresponding circuit breaker or, for example,remove the safety fuse or

switch off at the corresponding RCD protective switch, so that the socket is fully disconnected).

You can then unplug the power adapter from the mains socket. Dispose of the faulty power

adapter in an environmentally friendly way, do not use it any more. Replace it with a power

adapter of the same design.

c) Operation

• The product is only intended for use in dry indoor locations. No part of the product should

become damp or wet; never handle it if your hands are wet!

Power adapters pose the potential risk of a fatal electric shock!

• Choose a stable, even, at and sufciently large surface for setting up the docking station.

• Never use the product immediately after moving it from a cold room into a warm one. The

condensation that forms may damage the product under certain circumstances. A power unit

also carries the risk of a potentially fatal electric shock!

Allow the product to reach room temperature before connecting it to the power supply and

putting it into use. In some cases, this may take several hours.

• When setting up the product, make sure that the cables are neither kinked nor pinched.

Connections and control elements

1 Power switch (”O“ = off, „I“ = on)

2 Round socket for power supply

3 RJ45 network jack

4 HDMI port 1

5 Display port 1

6 HDMI port 2

7 Display port 2

8 USB3.0 connectors

9 USB type C™ connector for the connection to a USB3.0/3.1 port of a computer

10 USB3.0 connectors

11 Power LED

12 3.5 mm jack for headphones

13 3.5 mm jack for microphone

Getting started

• Switch on your computer, if not done yet, and wait until the operating system has nished loading.

• Insert the enclosed CD into the corresponding drive on your computer. If the installation program does not

start automatically, open the CD main directory and start the “setup.exe“ program. Follow all instructions

given by the software or Windows.

Latest drivers are available at www.displaylink.com.

• Afterwards, it may be necessary to restart.

• Connect the round low voltage plug of the enclosed power adapter to the corresponding connector on the

back of the docking station.

• Connect the power adapter to the mains voltage; i.e. plug it into a mains socket.

• Connect the USB type C™ connector of the docking station to an available USB connector on your com-

puter.

A conventional USB2.0 port cannot deliver the required amounts of data (for the image display

on the connected monitors) and is thus not suitable for the docking station. Therefore, use a

USB3.0 or USB3.1 port.

• Place the docking station on a level, rm and sufciently large area.

Protect valuable furniture surfaces by using a suitable mat to prevent scratches or pressure

points.

• Switch the docking station on. The power LED (11) lights up. At the rst startup, Windows may nd new

hardware and will install the required drivers. The screen may icker a few times or go black for a short

time during the installation; this is normal (detection of the docking station’s external graphics card).

• Connect your devices to the matching ports of the docking station.

Operating instructions

USB Type C™ Docking Station

Item no. 1574791

Intended use

The product is designed for connection to a computer with a USB3.0 interface in order to provide additional

interfaces:

a) External graphics card: By means of a special driver, up to two monitors connected to it (with HDMI, DVI

or VGA port) work as if your computer or your normal graphics card had additional monitor connections.

b) External network adapter: A network connection can be established, e.g., if the computer does not have

a network connection.

c) External USB hub: An integrated USB3.0 hub provides 6 additional USB ports, e.g., for a USB mouse or

USB keyboard.

d) External sound card: Two stereo jack sockets (3.5 mm, for headphone and microphone) are used to

connect e.g., a headset.

The included power adapter is used to the voltage/power supply of the docking station.

For safety and compliance reasons, the product must not be converted or modied in any way. If you use the

product for other purposes than those described above, the product may be damaged. Moreover, improper

use involves risks such as short-circuits, re, electric shocks, etc. Please read the operating instructions

carefully and do not discard them. If you pass the product on to a third party, please hand over these operat-

ing instructions as well.

This product complies with the applicable national and European Regulations. All names of companies and

HDMI is a registered trademark of HDMI Licensing L.L.C.

Package contents

• Docking station

• USB cable #1 (USB3.0 type A connector on USB type C™ connector

• USB cable #2 (USB3.0 type C™ connector on USB type C™ connector

• AC adapter

• Driver CD

• Operating instructions

Up-to-date operating instructions

Download the latest operating instructions via the link www.conrad.com/downloads or scan the QR code.

Follow the instructions on the website.

Explanation of symbols

The lightning symbol inside a triangle is used when there is a potential risk of personal injury,

such as electric shock.

An exclamation mark inside a triangle indicates important instructions in this operating manual

which must be adhered to.

The arrow symbol indicates specic tips and advice on operation.

Safety instructions

Please read the operating instructions carefully and pay particular attention to the safety

instructions. We do not assume liability for any injuries/material damages resulting from

failure to observe the safety instructions and the information in these operating instruc-

tions regarding the proper use of the product. Furthermore, in such cases, the warranty/

guarantee will be null and void.

a) General information

• The product is not a toy. Keep out of the reach of children and pets.

• Do not carelessly cast aside the packaging material. It may become a dangerous plaything

for children.

• Protect the product from extreme temperatures, direct sunlight, strong vibrations, high humid-

ity, moisture, combustible gases, vapours and solvents.

• Never expose the product to mechanical stress.

• Please handle the product carefully. The product can be damaged if crushed, struck or

dropped, even from a low height.

• Also observe the safety and operating instructions of any other devices that are connected

to this product.

• If safe operation is no longer possible, take the device out of service and secure it against

unintended use. Safe operation is no longer possible, if the product:

- shows visible damage,

- no longer functions properly,

- has been stored under adverse ambient conditions for an extended period of time or

- has been exposed to considerable strain during transport.

• If you have doubts about how the product should be operated or how to safely connect it,

consult a qualied technician.

• Maintenance, adjustment and repair work should only be carried out by an expert or a spe-

cialised workshop.

• If you have any questions that are not answered in these operating instructions, please con-

tact our technical customer service or other professionals.

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).

All rights including translation reserved. Reproduction by any method, e.g. photocopy, microlming, or the capture in

electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.

This publication represent the technical status at the time of printing.

Tips and notes

a) General information

• Do not disconnect the USB connection between the docking station and the computer during operation,

as this may lead to data loss.

• Do not use the docking station without the enclosed power adapter.

b) Connecting the monitor

• The docking station allows the operation of up to 2 monitors.

Please note:

Connect only one monitor to each of the two combined monitor outputs “DISPLAY 1” and

“DISPLAY 2”.

Connect monitor # 1 to the HDMI or “DISPLAY 1” display port connector (see chapter “Connec-

tions and controls”, pos. “4” or “5”); connect monitor # 2 to “DISPLAY 2” (see gure, pos. “6” or “7”).

If you connect both monitors to the outputs “4” and “5” for example, you will only get a picture on

the monitor that is connected to the display port.

If you want to connect a 5K monitor to the docking station, connect both display port outputs of

the docking station to your monitor.

• The operating system should be able to recognize the second monitor automatically after the drivers are

installed and the computer is connected to the docking station. For example, in Windows, the mouse

pointer can be moved from the rst monitor to the second one. Also, windows on the rst monitor can be

moved to the second monitor.

• Depending on what mode you have set in the display settings of the driver software or,on Windows, a

second monitor can be used as an extension of the rst monitor, or the monitors show the same display

content.

• During startup/ boot up of the computer, there won’t be a picture on the monitor that is connected to the

docking station, since at this point the driver is not yet loaded.

A picture will appear only after the operating system and the driver have nished loading.

• To change the monitor allocations, edit the graphic settings in Windows (for Windows 7/8/10, click on an

unused area of the desktop with the right mouse button and select “screen resolution”) or even use the

setting options of the docking station’s software (Displaylink functions).

For example, the location of the second monitor can be changed (whether it is allocated to the left or the

right of the rst monitor), or you can adjust the resolution as desired.

• Since the picture content is transferred via USB3.0/3.1, you may encounter delays in the display of picture

content, if the picture content changes quickly. This is observed mostly if a very high resolution was

selected or videos are being played.

• The graphic output of the docking station cannot be used for games, as it is not suitable for 3D operation.

• Since all data between the computer and docking station is transferred via a USB port, the use of graphics

output, network port, external sound card and USB3.0 hub have an impact on each other. Transferring

large data amounts via the network connection or the USB3.0 hub will reduce the speed of the graphics

output (e.g., moving windows on the desktop gets slower, or similar).

• Never set a higher resolution/display refresh rate (or a combination of both values) than supported by the

monitor. Observe the user manual of the monitor for this.

c) USB 3.0 Hub

• The USB3.0 ports of the integrated USB hub may be used with any USB device, such as a USB webcam,

USB mouse or USB keyboard.

• The USB3.0 hub is compatible with USB2.0/1.1. You can also connect slower devices.

• It doesn’t matter, which of the USB3.0 ports you use rst.

d) External sound card

• One stereo jack bushing is used as a adset output, the other one as a connection for microphones. For this

purpose, observe the symbols next to the sockets. Do not swap round the connectors, otherwise neither

the headset, nor the microphone operates.

• If the computer to which the docking station is connected has its own sound card, Windows normally

automatically activates the ports on the docking station when the latter is connected to the computer and

switched on.

• In the audio properties of the Windows system control, the microphone input and the audio output can be

selected, so that you can switch between internal and external sound cards.

e) Network connection

• If there is a network or system administrator who is responsible for your network (for example, in a larger

company), let the administrator set up the connection and the conguration.

• The RJ45 network port on the docking station is connected to your router or network switch,for example,

via a fully wired network cable with a 1:1 connection.

• The specied maximum data transfer rate of 1000MBit (gigabyte LAN), or about 125MByte/s, is never

reached in practical operation. This is caused by the transmission method used, transmission errors, other

devices in the network and so on; another reason is the maximum transfer rate of the USB port (the data

for the graphic output is transferred via the same USB port; the same is true for the external sound card

and the USB hub in the docking station).

• With Windows, it might take some time until the PCs appear on the network. When you turn on the com-

puter, after a few seconds, when Windows is loaded on all computers, you will be able to access all the

other PCs immediately.

If, after a few minutes, it is still not possible to access other PCs, check any rewall and/or virus scanner

settings that may be used.

Naturally, the access permissions also have to be set accordingly, if you are using an operating system

that offers such features.

Consult the applicable operating instructions, when using a network printer or other devices in the network.

There are numerous causes explaining why a network connection is not successful. Please refer to the

appropriate specialist literature or to a specialist technician.

• If you are not using a DHCP Server (e.g., integrated in all DSL routers), you should assign an IP address

to each PC.

Set the rst computer e.g., to 192.168.1.2, the second to 192.168.1.3, etc. The rst three numbers must

be the same for all computers; the last number can be between 1 and 254.

The „subnet mask“ has to be set to 255.255.255.0 for all the computers in the network.

• Please keep in mind that an IP address (such as 192.168.1.1) can only be used once in the network. When

you set your router to the IP address 192.168.1.1, no other device in the network can use this IP address!

Care and cleaning

Before cleaning the product, switch it off and unplug the wall plug transformer from the mains socket.

Never use abrasive cleaning agents, rubbing alcohol or other chemical solutions, since these could damage

the casing or even impair operation.

Use a dry, lint-free cloth to clean the product.

Disposal

Electronic devices are recyclable material and do not belong in the household waste. Dispose of

an unserviceable product in accordance with the relevant statutory regulations.

Technical data

a) Docking station

Latest drivers are available at www.displaylink.com.

Operating voltage ..........................................20 V/DC

USB standard ................................................USB3.0

Number of USB3.0 ports ...............................6

Video outputs .................................................2x HDMI

.......................................................................2x display port

Monitors connected .......................................1 or 2

Resolution for video outputs ..........................max. 4K

If both display port connectors are used for one monitor, a resolution up to 5K is possible,

5120 x 2880, max. 60 Hz.

Audio connections .........................................1x audio output (3.5 mm jack socket)

.......................................................................1x microphone input (3.5 mm jack socket)

Network ports ................................................1x Gigabit (10/100/1000 MBit)

Ambient conditions ........................................ Temperature 0 °C to +40 °C, air humidity 10% to 90% relative,

noncondensing

Dimensions (W x H x D) ................................225 x 85 x 27 mm

Weight ...........................................................350 g

b) AC adapter

Operating voltage ..........................................100 - 240 V/AC, 50/60 Hz

Output ............................................................20 V/DC, 2 A

Page is loading ...

Renkforce Dual 4K Owner's manual

Brand: Renkforce

Model: Dual 4K

Category: Coffee making accessories

Type: Owner's manual

Download PDF

report

in other languages

français: Renkforce Dual 4K Le manuel du propriétaire
Deutsch: Renkforce Dual 4K Bedienungsanleitung
Nederlands: Renkforce Dual 4K de handleiding

Renkforce Dual 4K Owner's manual

Renkforce Dual 4K Owner's manual

in other languages

Related papers

Other documents