Fagor CFS-900AX Owner's manual

FR GUIDE D'UTILISATION

ES MANUAL DE UTILIZACIÓN

EN GUIDE TO INSTALLATION

DE BETRIEBSANLEITUNG

Hotte décorative

Campana extractora decorativa

Decorative Hood

Dekor-Dunstabzugshaube

Page is loading ...

6

••

DESCRIPTION DE VOTRE APPAREIL

Ouïes

Cheminée

Enveloppe

Commandes

A

B

C

D

11 //

A L’ATTENTION DE L’UTILISATEUR

FR

2

7

4

m

Evac Min 650- Max 1002

Reci Min 750-Max 1102

5

0

m

600 / 700 / 9

00 / 1200 m

m

608mm

112mm

3

1

m

(

9

0

0 /1

20

0

)

2

7

1

m

( 6

0

/ 7

0

)

B

C

A

D

Page is loading ...

24

••

DESCRIPCION DE SU APARATO

Aberturas

Chimenea

Carcasa

Mandos

A

B

C

D

11 //

A LA ATENCIÓN DEL USUARIO

ES

2

7

4

m

Evac Min 650- Max 1002

Reci Min 750-Max 1102

5

0

m

600 / 700 / 9

00 / 1200 m

m

608mm

112mm

3

1

m

(

9

0

0 /1

20

0

)

2

7

1

m

( 6

0

/ 7

0

)

B

C

A

D

Page is loading ...

34

33 //

UTILIZACIÓN DEL APARATO

ES

SATURACIÓN DEL FILTRO DE CARBÓN (Filtro opcional)

••

AUTO STOP VENTILADOR

••

AUTO STOP ALUMBRADO

••

Si se olvida de apagar su campana, ésta se detendrá al cabo de 9 horas de funcionamiento.

Si se olvida de apagar luz de su campana, ésta se apagará al cabo de 9 horas de funciona-

miento.

SATURACIÓN DEL FILTRO CARTUCHO

••

Cuando el piloto

FF ppaarrppaaddeeaa

, nos indica que los filtros de cartucho deben limpiarse (ver capí-

tulo “Limpieza filtro cartucho”).

Presionar prolongadamente sobre la tecla para desbloquear la función “saturación”.

Cuando el piloto

FF nnoo ppaarrppaaddeeaa

, indica que los filtros de carbón deben cambiarse (ver capítulo

“Cambio del filtro de carbón”).

Presionar prolongadamente sobre la tecla para desbloquear la función “saturación”.

Únicamente en modo reciclaje.

MODO RECICLAJE / EVACUACIÓN

••

Presione prolongadamente y para elegir el modo de evacuación o reciclaje.

El piloto o se ilumina y la configuración puede comenzar.

Presione brevemente la tecla o para seleccionar el modo de reciclaje ( ) o el modo

de evacuación ( ).

Presione brevemente y para validar la configuración.

Presione brevemente sobre para anular la configuración.

Page is loading ...

38

As part of our commitment to constantly improving our products, we reserve the right to make

changes to them based on technical advances to their technical and functional features and ap-

pearance

Warning:

Before installing and using your appliance, please carefully read this Guide to

Installation and Use, which will allow you to quickly familiarise yourself with its operation.

ES

20

FR

02

EN

38

DE

56

39

TABLE OF CONTENTS

11 // NNOOTTIICCEESS TTOO TTHHEE UUSSEERR

• Safety recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

• Environmental protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

• Description of your appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

22 // IINNSSTTAALLLLIINNGG YYOOUURR AAPPPPLLIIAANNCCEE

• Using the evacuation mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

• Using the recycling mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

• Electrical connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

• Assembling the hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

• Assembling the ventilation shaft

º Outdoor evacuation ...........................................................................46

º Recycling ..............................................................................................47

33 // UUSSIINNGG YYOOUURR AAPPPPLLIIAANNCCEE

• Description of control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

44 // CCAARRIINNGG FFOORR

AANNDD CCLLEEAANNIINNGG YYOOUURR AAPPPPLLIIAANNCCEE

• Cleaning the filter cartridges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

• Changing the carbon filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

• Cleaning the outer surfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

• Changing the light bulb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

• Maintaining your appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

55 // TTRROOUUBBLLEESSHHOOOOTTIINNGG ...............................................................................................

...................................................................................................

50

66 // AAFFTTEERR--SSAALLEESS SSEERRVVIICCEE...................................................

.........................................................................................................................................

50

EN

40

1 / NOTICES TO THE USER

SAFETY RECOMMENDATIONS

— This oven was designed for use by private

persons in their homes.

— This appliance is not designed to be used by

people (including children) with reduced phys-

ical, sensorial or mental capacity or people

lacking in experience or knowledge, except if

they have the benefit, through the intermedi-

ary of a person responsible for their safety, of

preliminary supervision or instruction con-

cerning the use of the appliance. It is advis-

able to supervise children to make sure that

they do not treat the appliance as a toy.

— When you receive the appliance, unpack or

have it unpacked immediately. Give it an over-

all general inspection. Make note of any con-

cerns or reservations on the delivery slip and

make sure to keep a copy of this form.

— Your appliance is intended for standard

household use. Do not use it for commercial

or industrial purposes or for any other pur-

pose than that for which it was designed.

— Do not modify or attempt to modify any of

the characteristics of this appliance. This

would be dangerous to your safety.

— Repairs must only be carried out by an

approved specialist.

— Always unplug the hood before cleaning it

or performing other maintenance acts.

— Provide adequate ventilation for the room in

the case of simultaneous use of the hood and

other appliances powered by an energy

source other than electricity. This will prevent

the hood from aspirating the combustion gas-

es.

— You should never "flambé" dishes under the

hood or operate gas rings under the hood

without placing cookware on them (the flames

sucked up into the hood can damage the

appliance).

— When frying food under the appliance, you

must carefully monitor the preparation at all

times. Oils and grease brought to very high

temperatures can catch fire.

— Respect the recommended frequency of

cleaning and filter replacements. The accumu-

lation of grease deposits may cause a fire.

— The hood should never be used over a com-

bustible fuel burning stove (wood, coal, etc.).

— Never use steam or high-pressure devices

to clean your appliance (requirement imposed

by electrical safety).

— With a view to constantly improving our

products, we reserve the right to modify their

technical, functional or aesthetic characteris-

tics, making any changes to their features

considered necessary or desirable in view of

technical progress.

— In order to easily locate the reference infor-

mation for your appliance, we recommend

that you note these data on the "After-Sales

Service Department and Customer Relation

•

Attention

Keep this user guide with your appli-

ance. If the appliance is ever sold or trans-

ferred to another person, ensure that the

new owner receives the user guide. Please

become familiar with these recommenda-

tions before installing and using your appli-

ance. They were written for your safety and

the safety of others.

Warning

In the case of a kitchen heated by a

device connected to a chimney (a stove, for

example) the "recycling" version of the

hood should be installed. Do not use the

hood without metal filters.

Suitable ventilation should be provided in

the room when the hood is used at the

same time as appliances operated by gas

or another combustible fuel.

EN

41

Warning

Installation should only be performed by installers and qualified technicians.

Warning

Remove the protective film from the filter cartridge before use.

ENVIRONMENTAL PROTECTION

•

— This appliance's packaging material is recyclable. Help recycle it and protect the environment

by dropping it off in the municipal receptacles provided for this purpose.

— Your appliance also contains a great amount of recyclable material. It is marked with this label

to indicate the used appliances that should not be mixed with other waste. This way, the appli-

ance recycling organised by your manufacturer will be done under the best possible

conditions, in compliance with European Directive 2002/96/EC on Waste Electrical

and Electronic Equipment. Contact your town hall or your retailer for the used appli-

ance collection points closest to your home.

— We thank you doing your part to protect the environment.

1 / NOTICES TO THE USER

EN

42

•

DESCRIPTION OF YOUR APPLIANCE

Vents

Ventilation shaft

Top surface

Control panel

A

B

C

D

1 / NOTICES TO THE USER

EN

2

7

4

m

Evac Min 650- Max 1002

Reci Min 750-Max 1102

5

0

m

600 / 700 / 9

00 / 1200 m

m

608mm

112mm

3

1

m

(

9

0

0 /1

20

0

)

2

7

1

m

( 6

0

/ 7

0

)

B

C

A

D

43

2 / INSTALLING YOUR APPLIANCE

USING THE EVACUATION MODE

If you possess an outlet to the exterior

(fig. 1)

Your hood can be connected to this outlet

using a flue (minimum diameter 125 mm that is

enamelled, in aluminium, flexible or made of

inflammable material). If your flue is less than

125 mm in diameter,

yyoouu mmuusstt uussee tthhee rreeccyy--

cclliinngg mmooddee..

•

USING THE RECYCLING MODE

If you do not possess an outlet to the exterior

(fig. 2)

All of our appliances can be used in recycling

mode.

In this case, you should add an active carbon

filter which will keep in odours.

(See Chapter 4: Changing the carbon filter.)

•

- The appliance must be unplugged during installation or when any repair or maintenance work

is being performed.

- Ensure that the network voltage corresponds to the voltage noted on the identification plate

located inside the hood.

- If the electrical installation at your residence requires any changes in order to hook up your

Appliance, call upon a professional electrician.

- If the hood is being used in evacuation mode, do not connect the appliance to a combustion

gas exhaust duct (boiler, chimney, etc.) or to a CMV (controlled mechanical ventilation) system.

- Under no circumstances should the exhaust duct empty into the attic.

- Install the hood at a safe distance of at least 70 cm from an electric, gas or combined cooking

hob.

EN

125

150

125

150

fig. 1

fig. 2

44

Warning

This appliance is delivered with a H 05

VVF power cord that has three-0.75 mm2

conductors (neutral, phase and ground). It

must be connected to the main power supply

(which should be a 220-240 V single phase

current) via a CEI 60083 standardised socket

that should remain accessible after installa-

tion, in keeping with installation guidelines.

We cannot be held responsible for any acci-

dent resulting from an inexistent, defective

or incorrect ground lead. The fuse for your

installation must be 10 or 16A. If the power

cable is damaged, call the after-sales serv-

ice department in order to avoid danger.

Warning

If the electrical installation at your resi-

dence requires any changes in order to hook

up your appliance, call upon a professional

electrician.

Warning

If the hood displays any malfunctions,

unplug the appliance or remove the fuse cor-

responding to the electrical socket where

your appliance is plugged in.

•

ELECTRICAL CONNECTIONS

During installation and maintenance opera-

tions, the appliance must be unplugged from

the electrical grid; fuses must be cut off or re-

moved.

The electrical connections are made before

the appliance is installed in its housing.

Ensur

e that:

- the electrical installation has sufficient volt-

age,

- the electrical wires are in good condition,

- the diameter of the wires complies with the

installation requirements.

2 / INSTALLING YOUR APPLIANCE

EN

Important

The accessible parts of this appliance

may become hot if it is used with a cooking

appliance.

45

2 / INSTALLING YOUR APPLIANCE

ASSEMBLING THE HOOD

Warning

The hood must be installed in compli-

ance with all applicable regulations concern-

ing the ventilation of premises. In France

these regulations are described in DTU 61.1

from the CSTB. In particular, the evacuated

air should never be conveyed to a duct used

to evacuate smoke from appliances that use

gas or other combustible fuels. Unused

ducts may only be used after approval from

a competent specialist.

The minimum distance between the cooking

surface and the lowest part of the hood must

be 70 cm. If the instructions for the hob

installed under the hood specify a distance of

more than 70 cm, this requirement must be

respected.

— Draw a horizontal line 70 cm minimum from

the cooker top (A/fig. 1).

— Draw a vertical line (B/fig. 1) on the wall that

is centred over the cooker top and that ex-

tends from the horizontal line drawn in the

previous step (A) to the ceiling.

— Place the drilling template (C/fig. 1) on the

wall. In the case of a hollow wall, use suitable

wall plugs and screws.

— Drill the two holes. Insert the 2 wall plugs.

— Screw the fastening bar to the wall (C/fig. 2),

with the 2 screws (D/fig. 2)

— Hang the suction hood by its hooks (E/fig.

2).

— Adjust the height and level by moving the

clamping screws (E/fig. 2) of the supports

(the top screw for horizontal fit and the bot-

tom screw for fitting to the wall).

— Fit the anti-lifting screw (D/fig. 1)

— Remove the adhesive tape from the compo-

nent unit (F/fig. 3).

— Lift the unit around 2 cm then release it. Give

it a quarter turn then slide it and fasten it using

2 screws above the motor (fig. 3).

WWaarrnniinngg:: ddoo nnoott ddaammaaggee tthhee ccaabblleess wwhhiillee rroo--

ttaattiinngg aanndd ffaasstteenniinngg..

•

fig. 2

> 70 cm

=

C

A

B

fig. 1

EN

90°C

2cm

1

2

3

fig. 3

D

E

F

D

C

46

2 / INSTALLING YOUR APPLIANCE

EN

ASSEMBLING THE VENTILATION

SHAFT

•Outdoor evacuation

— Using the two screws (fig. 1), attach the met-

al chimney bracket against the wall, flush with

the ceiling for support.

— Mount the back-flow valve near the motor

outlet (fig. 2). This back-flow valve makes it

possible to block the entry of air from the out-

side.

— If a 125 mm flue is being installed, use the

adapter provided (fig. 3). If the diameter of

your exterior flue is less than125 mm, you

must connect your hood in recycling mode.

— Slide the end of the flue over the motor out-

let (fig. 4).

— Prepare your telescoping ventilation shaft,

taking care not to block the vents (B/fig. 4).

Fit the chimney to the hood and lift the upper

portion to adjust the height and then screw it

(G/fig.4) on the metal chimney bracket (A/fig.

4).

•

fig. 1

fig. 2

fig. 3

A

B

C

D

E

CChhiimmnneeyy bbrraacckkeett

FFlluuee

AAddaapptteerr

BBaacckk--ffllooww vvaallvvee

MMoottoorr oouuttlleett

F

TTeelleessccooppiinngg vveennttiillaattiioonn sshhaafftt

CChhiimmnneeyy hhoollddiinngg ssccrreeww

G

Tip

For optimal use of your appliance, we

recommend that you connect the hood to a

150 mm-diameter flue (not delivered with the

appliance). Minimise the number of angles

and bends and the lengths of the flue. In the

event that the hood will be operated using

outdoor evacuation, you should ensure a

sufficient inflow of fresh air to avoid a pres-

sure deficiency in the room.

fig. 4

A

C

D

E

F

G

B

47

2 / INSTALLING YOUR APPLIANCE

EN

•Recycling

— Remove the back-flow valve (fig. 1).

— Using the two screws (fig. 2), attach the plastic

smoke deflector against the wall, flush with the

ceiling for support. Be careful to centre the

deflector in relation to the vertical line drawn on

the wall (fig. 2).

For models up to 700 mm, add the 2 struts sup-

plied in the pocket (A/fig. 2)

— Slide one end of the flue over the deflector and

the other end over the motor outlet (fig. 3).

— Prepare your ventilation shaft, taking care to

face the vents upward so that they are visible

(B/fig. 3).

— Attach the assembled chimney (C/fig. 3) to the

hood and lift the upper portion to adjust the

height, then screw it to the smoke deflector

(A/fig. 3) using the two screws (F/fig. 3).

A

B

C

D

E

SSmmookkee ddeefflleeccttoorr

TTeelleessccooppiinngg vveennttiillaattiioonn sshhaafftt

FFlluuee

MMoottoorr bbrraacckkeett

VVeennttss

fig. 1

fig. 2

CChhiimmnneeyy hhoollddiinngg ssccrreeww

F

A

fig. 3

A

B

D

E

F

C

48

3 / USING YOUR APPLIANCE

EN

••

DESCRIPTION OF CONTROL PANEL *(Depending on model)

E

A

C

D

B

On / Off

A

B

C

Timer / Delayed shutdown

(10 min)

Indicator

Speed reduction

D

E

Lighting

F

G

F

G

Speed increase

Boost

H

I

H

I

Oxygen *

Automatic mode *

Tip

This guide to Installation and Use is valid for several models. Minor differences in

details and fittings may emerge between your appliance and the descriptions provided.

AUTOMATIC MODE (depending on model)

••

These hoods are designed with the capacity to adapt. Fitted with sensing devices, they activate

automatically when they detect any emission of steam or heat, spontaneously adapt suction

speed and stop operating when the last of the smoke has been evacuated.

49

3 / USING YOUR APPLIANCE EN

Selecting the type of hob in automatic mode *

To select your hob type, your hood should be switched off.

Press for >2s simultaneously on and to enter configuration mode. Press to select

the hob type: the indicator displays I for an induction hob, U for a ceramic hob and G for a gas

hob. Pressing once and simultaneously on and will validate your configuration.

Automatic mode setting

You have the possibility of refining the reaction time of your hood in automatic mode.

To adjust its sensitivity, press the button for more than 2s.

: minimum sensitivity

: average sensitivity

: maximum sensitivity

Press to increase sensitivity and to reduce it.

Press once to cancel your settings

Your settings are automatically validated after 10s.

Press . The indicator will flash and tell you that the hood is in automatic mode.

Changing to automatic mode

Shutting down the hood in automatic mode

You are in automatic mode and want to shut down your hood. Press .

Info

Timed shutdown is automatic in these hoods.

Through this system, the hood continues to operate for five, ten or fifteen minutes, depending

on the power used for cooking, in order to process and remove all smoke.

50

3 / USING YOUR APPLIANCEEN

SWITCHING ON THE HOOD IN MANUAL MODE

••

Pressing the button starts up the hood at speed 1 (the indicator displays 1).

••

SWITCHING OFF THE HOOD

••

Press the button to switch the hood off.

CHANGING SPEED

••

After starting up the hood, you can change the suction speed by pressing or .

The function allows your hood to remain for 10 min at maximum speed 4 and then change

to speed 2

At the end of cooking, you can select the button to shut down your hood. This function

maintains suction for 10 minutes at the selected speed.

To cancel delayed shutdown, press the same button to stop the delayed function.

DELAYED SHUTDOWN

51

3 / USING YOUR APPLIANCE EN

LIGHTING

••

Press the button once to switch the halogen lighting of your hood on or off.

Your hood (depending on the model) gives you the possibility of changing the intensity of the

light as you wish to make it more or less bright. Pressing and holding the button can vary

the intensity of the lighting.

OXYGEN FUNCTION (DEPENDING ON MODEL)

••

Press the button once to switch on the hood at reduced speed and in silent mode for 1

hour. The indicator is displayed.

To shut down this function press again.

PPrrooggrraammmmiinngg tthhee OOxxyyggeenn ffuunnccttiioonn

Press and hold the button to activate the programming.

11

and will flash alternately, indicating the start of programming.

Every time the button is pressed once, this will increase the period of operation of the

Oxygen function (from 2h to 9h maximum). The hood will operate at reduced speed and in silent

mode during the selected period. The figure representing the time in hours (1, 2, 3, 4, 5, 6, 7, 8

or 9) and will flash alternately throughout the Oxygen program.

Every time the button is pressed once the time will be reduced (from 8h to 1h).

The program is validated automatically after 10 min.

Programming can be cancelled before automatic validation by pressing the button .

To shut down this function press

52

33 //

USING YOUR APPLIANCE

EN

CARBON FILTER SATURATION (Optional filter)

••

AUTOMATIC FAN SHUTDOWN

••

AUTOMATIC LIGHTING SHUTDOWN

••

If you forget to switch off your hood, it will shut down after 9 hours’ operation.

If you forget to switch off the lighting on your hood, it will shut down after 9 hours’ operation.

FILTER CARTRIDGE SATURATION

••

When the

FF iinnddiiccaattoorr iiss ffllaasshhiinngg

, this indicates that the filter cartridges should be cleaned (see

section on “Cleaning the filter cartridge”).

Press and hold the button to release the “saturation” function.

When the

FF iinnddiiccaattoorr iiss nnoott ffllaasshhiinngg

, it indicates that the carbon filters should be changed (see

section on “Changing the carbon filter”).

Press and hold the button to release the “saturation” function.

Only in recycling mode.

RECYCLING / EVACUATION MODE

••

Press and hold the and buttons to select Evacuation or

Recycling mode. The or indicator is displayed. You can now enter your settings.

Press or once to select recycling mode ( ) or evacuation mode ( ).

Press and once to validate the settings.

Press once to cancel the settings.

53

CHANGING THE LIGHT BULB

•

MMooddeell wwiitthh hhaallooggeenn bbuullbb

— Remove the lighting port (fig. 2).

— Change the G4-20W-12V halogen bulb.

— Replace the bulb by repeating these steps

in reverse order.

fig. 2

CLEANING THE OUTER SURFACES

To clean the outside of your hood, use soapy water, but do not use abrasive creams or scrubbing

sponges.

•

4 / CARING FOR AND CLEANING YOUR APPLIANCE

Warning

Always unplug the hood before cleaning it or performing other maintenance acts.

Regular maintenance of your appliance is a guarantee of proper functioning, good perform-

ance and durability.

Warning

Failure to respect the guidelines for cleaning the appliance and filters may cause fires.

Please carefully adhere to the maintenance recommendations.

CLEANING THE FILTER CAR-

TRIDGES

They must be cleaned after approximately 30

hours of use or at least once a month. These fil-

ters can be cleaned in a vertical position in your

dishwasher. Use a brush, hot water and mild de-

tergent.

Rinse and dry them thoroughly before returning

them to the hood.

•Dismantling the filter cartridge

( fig. 1)

— Replace it after approximately 120 hours of

use.

— Remove the filter cartridge by unclipping it (fig.

1).

•

CHANGING THE CARBON FILTER

(depending on model)

Replace it after approximately 120 hours of

use.

— Remove the filter cartridge by unclipping it (fig.

1).

•

EN

fig. 1

Page is loading ...

Fagor CFS-900AX Owner's manual

Related papers

Other documents