Robstep X1 Series User manual

Page is loading ...

47

GB

1. Introduction of manual

Thank you for choosing and purchasing

Robstep X1. This manual is designed to help

you assemble, use and maintain Robstep X1

quickly.

1.1 Overview

• Introducing features of Robstep X1

• Describing safety and warning

information

• Introducing parts of Robstep X1

• Notes for safe driving

• Maintenance methods

1.2 Reading guide

This manual is designed to help you use

Robstep X1 correctly.

WARNING!

When driving Robstep X1, you may suﬀ er

injury from falling, losing control collision,

etc. To reduce unknown risks, please read this

manual carefully.

Description of warning signs

When reading this manual, please pay

special attention to the following warning

information:

WARNING!

The user’s improper operation may cause injury.

WARNING!

Only for use on private roads and private land.

WARNING!

Please be aware that the regulations for

using this product vary from country to

country. It is the user’s responsibility to

be aware of and comply with the relevant

national regulations.

2. Introduction to Robstep X1

2.1 Three views of Robstep X1

48

2.2 Product description

The product you purchased is Robstep X1

lithium battery foldable vehicle, which is

developed and produced by Robstep.

Robstep X1 is the latest product launched

by Robstep with great innovation in user

expecience, safety, appearance, etc.,

which provised user with superior driving

experience.

2.3 Product information

2.3.1 Basic parts

1. Accelerator

2. Display panel

3. Brake handlebar

4. Upper telescopic rod

5. Clamp

6. Lower telescopic rod

7. Front case

8. Front fork

9. Front tire

10. Folding joint piece

11. Folding button

12. Battery

13. Pedal

14. Rear motor

15. Rear case

16. Saddle

17. On/oﬀ button

18. Speed reducer

2.3.2 Packing list

1. The frame

2. Upper telescopic rod

3. Foot brace

4. Battery

5. Charger

6. Screw package

7. Wrench package

8. USB line

9. Pedal

10. Seat

11. Warning light

12. Rear fender

13. Product manual

14. Warranty card

15. Battery maintenance card

WARNING!

After opening the box, please check the list

of products in the packing box ﬁ rst. Please

contact the sales manufacturer if ther is any

problem.

49

GB

2.3.3 Display panel

The display panel shows the operation status of Robstep X1.

2.3.4 USB charging port and Bluetooth audio

Other electronic products such as mobile phones, tablet etc. can be charged through USB

charging port.

Waterproof Bluetooth audio can connect mobile phone or tablet to play music.

Total mileage

indicator

Single ride mile-

age indicator

Failure indicator

Bluetooth con-

nection indicator

Parking indicator

Remote controller

indicator

Battery

percentage

indicator

Lamp indicator

Total/single ride

mileage

Driving speed

USB charging port

Bluetooth audio

50

2.3.5 Lithium battery

This section mainly introduces the speciﬁ cation, correct charging method, maintenance

method, safety notes etc. of the battery of Robstep X1.

2.3.5.1 Speciﬁ cations of battery

Type

High conﬁ guration/low conﬁ guration lithium battery

Charging time

3 hours

Voltage

48 V

Weight

1,7 kg (only for reference, be subject to actual weight)

Initial capacity

4400 mAh

Working temperature

-20 - +60 °C (recommend 0-45 °C)

Charging temperature

0 - +45 °C (recommend 10-30 °C)

Relative humidity of storage

80 ±25% R.H.

Noise

< 70 dB(A)

2.3.5.2 Capacity Depletion of Battery

If battery percentage doesn’t show up on the

display panel, it means the battery capacity

is extremely low, user must stop driving. In

this case, if user does not stop driving, the

lifespan of the battery would be shortened

signiﬁ cantly.

WARNING!

User should pay attention to the prompt

on the display panel and operate

correspondingly for safety when driving.

2.3.5.3 Battery Charging Steps

Insert one end of charging cable into the

charging port on Robstep X1 (make sure the

charging port is dry), and then insert the

plug of the charger into the power socket.

When the indicator of the charger turns to

green from red, it means the battery is fully

charged.

The battery can be charged directly when

locked at Robstep X1. And the battery can be

Charging port,

battery lock

51

GB

detached to charge also.

WARNING!

• Please use local standard plug.

• Please charge and store the battery

as described in the manual. Improper

operation may cause damage to the

battery and shorten the lifespan of the

battery.

• The time to fully charge Robstep X1 is

around 3 hours, and the charger current

will be cut oﬀ automatically after full

charge.

• The battery has a limited lifespan. After

600 cycles, the capacity declines to 80%

of the original capacity, and the using

time may be shortened rapidly even if

the battery is fully charged.

• Please fully charge the battery before ﬁ rst

ride. The battery will discharge gradually

if it is not used for some time.

• The battery can be charged before

capacity depletion.

• Please charge the battery under 10 to

30 °C as to keep battery at optimum

performance.

• It is normal that the battery heats up

after being used for a long time.

• In cold places, the driving distance will

be shortened even if used a fully charged

battery.

• Please charge in clean and dry

environment.

• Please do not charge if the charging port

is wet.

• Please do not throw the battery into ﬁ re,

heat the battery, or store the battery

under high temperature.

• Please do not throw the battery into

water. Store it under dry conditions.

• Please do not insert conductive articles

into charging port, which may result in

damage to internal electronic devices.

• Do not modify the battery.

2.3.5.4 Direction for Using Battery Lock

• Insert key into the keyhole, press the key

slightly and rotate counter clockwise to

lock the battery.

2.3.5.5 Ultra-High or Ultra-Low Temperature

• When the working temperature of the

battery is within the recommended

temperature described in above battery

speciﬁ cation, Robstep X1 will operate at

highest eﬃ ciency.

• The temperature before and during

charge must be within above mentioned

working temperature range. When the

temperature is within the recommended

value, the charging eﬃ ciency will be

higher. If the temperature is too low

or too high, the charging time will be

extended or the battery can not be fully

charged.

• Under low temperature, the driving

distance will be shortened.

Battery keyhole

Charging port

52

2.3.5.6 Notes on Transporting Battery

WARNING!

• The lithium battery is regarded as a

dangerous article, and it may not be

allowed to transport without the prior

approval of local laws.

• If you want to transport Robstep X1

with a lithium battery by air or transport

the lithium battery separately by other

means, please contact Robstep or its

appointed agents.

2.3.5.7 Others

WARNING!

• Please strictly use the battery as

described in the manual to ensure your

safety and the safety of others, extend

the lifespan of the battery as long as

possible and improve its performance.

• If there is any damage, leakage, or

peculiar smell, please stop using the

battery immediately.

• Please do not contact any substance

leaking from the battery.

• Only professional engineer can

disassemble the internal of the battery.

• The battery contains toxic substance. It’s

not allowed to open or insert anything

into it.

• If Robstep X1 isn’t used for a period of

time, please store it after full charged and

charge it every three months.

• Do not let children and pets contact the

battery.

• Please use the charger provided by

Robstep for Robstep X1 only.

53

GB

2.4 Parameters of Robstep X1

Maximum driving speed

20 km/h (1)

Maximum driving distance

25 km (2)

Maximum uphill angle

15°

Net weight

17 kg (3)

Max load

100 kg

Packing dimension

88×40×49 cm

Product dimension

123×60×76 cm

Charging requirement

110-240 VAC 50-60 Hz

Charging time

3 hours

Motor type

DC brushless

Motor power

250 W

Charger

1,5 W

(1) The maximum driving speed can be conﬁ gured by an application. If Robstep X1 is in sprint

status during driving, it will run at a speed higher than 20 km/h in a short time.

(2) The maximum driving distance is measured on ﬂ at road with the load of 70 kg. This

parameter is aﬀ ected by the capacity of battery, driving habit, load, environment,

temperature, road conditions etc.

(3) The net weight refers to weight of the whole Robstep X1 with a 4,4 Ah lithium battery.

54

3. Operation of Robstep X1 and

safety notice

3.1 Operation description

Please read this manual carefully before

using.

• Please assemble Robstep X1 correctly

and fully charge the battery before use.

• Before driving, user should fully gen up

the driving environment.

• Please do not war sharp objects to avoid

injury during driving.

• Please do not drive on wet and slippery

ground.

Step 1: Take Robstep X1 frame and

parts out of the package.

Step 2: Robstep X1 electric bicycle

assembly

1. Let the power wire located at lower

telescopic rod go through the upper

telescopic rod.

2. Press the metal marble and make it be

in alignment with the groove inside the

lower telescopic rod, and then insert

the upper telescopic rod into the lower

telescopic rod.

Power wire

Upper telescopic rod

Lower telescopic rod

Metal marble

55

GB

3. Connect handlebar’s power wire with the

power wire inside the telescopic rod.

4. Insert the handlebar into the upper

telescopic rod, and tighten six screws,

and then buckle up the clamp.

5. Install saddle, and tighten four screws.

6. Install pedals, and tighten four screws,

and then unfold the pedals.

7. Unfold the bicycle body.

8. Buckle up the folding button to ﬁ x front

and rear parts.

56

9. Assemble kickstand and rear fender.

10. Insert the battery into the bicycle body,

and use the key to lock the battery.

Battery, charging port,

battery lock

Step 3: Press on/oﬀ button, and display panel will light up. Brake the left brake to enter

into driving mode, rotate the accelerator slightly, and Robstep X1 will get started.

Left brake

Display panel

On/oﬀ button

Accelerator

57

GB

WARNING!

• Please do not shake the handlebar

violently, which may increase the

probability of accidents.

• Please do not brake suddenly, especially

on smooth road.

• User must drive according to this manual.

• Please do not drive on wet or slippery

road, which may cause slip of wheels and

control loss.

3.2 Safety Notice

WARNING!

• Please read the manual carefully for safe

driving. You can learn a lot of important

information through it.

• Before using, please install every part

correctly to protect Robstep X1 from

damage during use.

• Please do not use Robstep X1 to injure

any persons or damage any property.

• Please do not change or modify any parts

of Robstep X1 randomly.

3.2.1 Weight Limit for User

The minimum weight limit for user: 20 kg

The maximum weight limit for user: 100 kg

3.2.2 Maximum Driving Distance

The maximum driving distance of Robstep

X1 is 25 km. However, it is aﬀ ected by many

factors, such as:

• Road Condition: The driving distance will

increase if user drives on ﬂ at road. If user

drives on hilly or bumpy road, the driving

distance will decrease.

• Speed & Driving Habits: The driving

distance will increase if user keeps the

driving speed stable. If user starts, stops,

accelerates or decelerates frequently, the

driving distance will decrease.

• Weight of User.

• Temperature: If driving under

recommended temperature, the driving

distance will increase. Otherwise, the

driving distance will decrease.

3.2.3 Speed Limit

The maximum speed is 20km/h.

3.2.4 Brake Description

• If braking under high-speed driving,

please do not use front brake ﬁ rst as to

avoid danger.

58

3.2.5 Using Environment

3.2.5.1 Driving under High or Low

Temperature Environment

• When user drives Robstep X1 under high

temperature, parts such as motor will

heat up obviously, which may aﬀ ect the

performance and lifespan of Robstep

X1. When the temperature of parts rises

to over 50°C, the speed limit decreases.

The decrease value depends on the

actual temperature. If you experience the

maximum speed reducing, allow your

Robstep X1 to cool down before you

continue using it.

• When user drives under low temperature

environment, lubrication of movable

parts will be aﬀ ected, and the resistance

will increase. Meanwhile, the discharge

speed and capacity of battery will decline

obviously. Therefore, please do not use

Robstep X1 violently below -5°C, which

may cause injury from losing control or

falling.

3.2.5.2 Uphill or Downhill Driving

• The maximum uphill and downhill angle

is 15°. User should pay attention to the

slope.

• When user drives uphill, Robstep X1

works with heavy loads, parts in the

system heat up rapidly, and the battery

is under a heavy load status. The lifespan

and capacity of the battery will be

shortened if driving uphill for a long time,

thus driving uphill for a long time is not

recommended. In addition, due to the

heavy load, the system will automatically

decrease the maximum driving speed for

safety.

• Over-speed downhill driving should

be avoided entirely. When user drives

downhill, the system may be under

energy recovery mode depending on

the slope and load, and thus continuous

downhill driving is helpful to increase

the driving distance. When the capacity

of battery is full, continuous downhill

driving may cause an overcharge of the

battery and even damage to the battery.

The system will automatically decrease

the maximum driving speed as to reduce

the possibility of overcharge.

3.2.5.3 Warning on Raining & Snowing

Conditions

• Riding at snow and heavy rain weather

should be avoided.

• Do not ride in deep water.

3.3 Other Safety Notices

• It’s forbidden to use battery or

accessories of other brands. If any

accident incurred due to misuse, it is not

within warranty scope.

• Modiﬁ cation of Robstep X1 voids

warranty. Any loss resulting from

modiﬁ cation, Robstep will not be

responsible. If there is any glitch, please

contact Robstep or its appointed agents.

• Destroying the labels on the battery

or on the body of Robstep X1 voids

warranty.

59

GB

4. Maintenance of Robstep X1

User needs to conduct routine maintenance

for Robstep X1. This chapter mainly

introduces some maintenance tips.

WARNING!

• Before conducting below operation,

ensure the power supply and the

charging cable are disconnected. When

power is on or the battery is under

charging, the following operation is

forbidden.

4.1 Maintenance

• Inspect regularly on screws of front and

rear tires to see if they are tightened.

• Check the outer tires tread to see if there

is any abrasion and crack. If the tires

are worn, please contact Robstep or its

appointed agents.

• Inspect regularly on screws of Robstep

X1 if they are tightened. If they are loose,

please tighten up.

• Before using, please check to conﬁ rm the

folding button is buckled up.

• Check regularly to see if there is any

broken parts. For any replacement,

please contact Robstep or its appointed

agents.

WARNING!

• For safety, if the battery reaches to 600

cycles, please return for inspection.

4.2 Cleaning

• Please use neutral detergent on Robstep

X1, wipe with a cloth, and then clean

again with a dry cloth.

WARNING!

• Do not spray water or other liquid

on Robstep X1 as to protect internal

electrical components and circuits from

being damaged.

4.3 Handling

• Lift and put down Robstep X1 with

proper skills:

• Make sure Robstep X1 is not connected

with the charger and is in power oﬀ

status.

• Lift with two hands at the middle of

Robstep X1 for handing. Please do not

use the handlebar as the main force.

4.4 Storage

• Please store Robstep X1 indoors with

dry and suitable temperature. If it isn’t

used for a period of time, please do not

connect it with power supply.

WARNING!

• User should not open internal circuit or

motor.

• Modiﬁ cation voids warranty.

• User should store Robstep X1 with a fully

charged battery, if not using for a long

period of time. And the battery should be

charged every three months.

60

5. Failure Treatment

• Serial Number: Every Robstep X1 has

a unique serial number, which is used

for quality tracking. The serial number

should be in safe keeping.

• Method to acquire the serial number:

Acquire from the packing case or the SN

registration card.

• If there is any glitches, please contact

Robstep or its appointed agents for

maintenance.

WARNING!

• User should operate in accordance

with this manual. Robstep shall not

be liablefor any legal consequences

resulting from user’s improper operation.

• For more information and support,

please visit the oﬃ cial website

www. robstep.com.

Service centre

Note: Please quote the product model

number in connection with all inquiries.

The model number is shown on the front of

this manual and on the product rating plate.

For:

• Complaints

• Replacements parts

• Returns

• Guarantee issues

• www.schou.com

Environmental information

Electrical and electronic equipment

(EEE) contains materials,

components and substances that

may be hazardous and harmful to

human health and the environment

if waste electrical and electronic equipment

(WEEE) is not disposed of correctly. Products

marked with the following crossed-out

wheeled bin are electrical and electronic

equipment. The crossed-out wheeled bin

indicates that waste electrical and electronic

equipment must not be disposed of with

unsorted household waste, but must be

collected separately.

Manufactured in P.R.C.

Manufacturer:

Schou Company A/S

Nordager 31

DK-6000 Kolding

be reproduced, either in full or in part, in any way by

electronic or mechanical means, e.g. photocopying or

publication, translated or saved in an information storage

and retrieval system without written permission from

Schou Company A/S.

61

GB

EC DECLARATION OF CONFORMITY

The undersigned manufacturer

Manufacturer: Dongguan Robstep Robot Co. Ltd

Address: 6 South Industrial Road, High-tech Industrial Park, Songshan Lake. Dongguan. China

Importer:

Address: Schou Company A/S Nordager 31. DK-6000 Kolding.

herewith declares that the product

Product identiﬁ cation: Robstep Foldable Electric Bike. Model X1

Art. no. 36745 and Item no. 44773

is in conformity with the provisions of the following EC directive

Reference no.

Title

Yes / No

2006/42/EC

Machine Directive

Yes

2014/30/EC

EMC Directive

Yes

2014/35/EC

LVD Directive

Yes

2011/65/EC + Amendments

RoHS Directive

Yes

and that the standards and/or technical speciﬁ cations referenced overleaf have been applied.

CCO Mr. Thomas L. Lyckhage at Schou Company A/S is authorized to compile the technical ﬁ le with reference towards

Directory 2006/42/EC Annex 2 1.A.2.

Standards and/or technical speciﬁ cations applied for this declaration of conformity, or parts there of :

Harmonized Standard No.

Title of the standard

EN 15194:2017

ETSI EN 301 489-1 V1.9.2

ETSI EN 301 489-17 V2.2.1

ETSI EN 301 489-3 V1.6.1

EN 61558-2-16:2009+A1:2013

EN 61558-1:2005+A1:2009

ETSI EN 300 440-1 V1.6.1:2010-08

ETSI EN 300 440-2 V1.4.1:2010-08

ETSI EN300 328 V1.9.1:2015-02

EN 62479:2010

EN 60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013

EN 61000-3-2:2014

EN 61000-3-3:2013

Place: Dongguan, China Date: 1/18/19

Title & Position in company:

Signature:

Page is loading ...

Robstep X1 Series User manual

Robstep X1 Series User manual

in other languages

Other documents