Makita JV0600 User manual

1

INSTRUCTION MANUAL

MANUEL D'INSTRUCTION

MANUAL DE INSTRUCCIONES

DOUBLE INSULATION

DOUBLE ISOLATION

DOBLE AISLAMIENTO

IMPORTANT: Read Before Using.

IMPORTANT: Lire avant usage.

IMPORTANTE: Leer antes de usar.

Jig Saw

Scie Sauteuse

Sierra Caladora

JV0600

011955

2

ENGLISH (Original instructions)

SPECIFICATIONS

Model JV0600

Length of stroke 23 mm (7/8")

Wood 90 mm (3-1/2")

Max. cutting capacities

Mild steel 10 mm (3/8")

Strokes per minute 500 - 3,100/min

Overall length 236 mm (9-1/4")

Net weight 2.4 kg (5.2 lbs)

• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.

• Specifications may differ from country to country.

• Weight according to EPTA-Procedure 01/2003

GEA008-2

General Power Tool Safety

Warnings

WARNING Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

serious injury.

Save all warnings and

instructions for future reference.

The term "power tool" in the warnings refers to your

mains-operated (corded) power tool or battery-operated

(cordless) power tool.

Work area safety

1. Keep work area clean and well lit. Cluttered or

dark areas invite accidents.

2. Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust. Power tools

create sparks which may ignite the dust or fumes.

3. Keep children and bystanders away while

operating a power tool. Distractions can cause

you to lose control.

Electrical Safety

4. Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodified plugs and matching outlets will

reduce risk of electric shock.

5. Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of

electric shock if your body is earthed or grounded.

6. Do not expose power tools to rain or wet

conditions. Water entering a power tool will

increase the risk of electric shock.

7. Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or

moving parts. Damaged or entangled cords

increase the risk of electric shock.

8. When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of

a cord suitable for outdoor use reduces the risk of

electric shock.

9. If operating a power tool in a damp location is

unavoidable, use a ground fault circuit

interrupter (GFCI) protected supply. Use of an

GFCI reduces the risk of electric shock.

Personal Safety

10. Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired or

under the influence of drugs, alcohol or

medication. A moment of inattention while

operating power tools may result in serious

personal injury.

11. Use personal protective equipment. Always

wear eye protection. Protective equipment such

as dust mask, non-skid safety shoes, hard hat, or

hearing protection used for appropriate conditions

will reduce personal injuries.

12. Prevent unintentional starting. Ensure the

switch is in the off-position before connecting

to power source and/or battery pack, picking

up or carrying the tool. . Carrying power tools

with your finger on the switch or energising power

tools that have the switch on invites accidents.

13. Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may

result in personal injury.

14. Do not overreach. Keep proper footing and

balance at all times. This enables better control

of the power tool in unexpected situations.

15. Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing, and gloves

away from moving parts. Loose clothes,

3

jewellery or long hair can be caught in moving

parts.

16.

If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used.

Use of

dust collection can reduce dust-related hazards.

Power tool use and care

17. Do not force the power tool. Use the correct

power tool for your application. The correct

power tool will do the job better and safer at the

rate for which it was designed.

18. Do not use the power tool if the switch does

not turn it on and off. Any power tool that cannot

be controlled with the switch is dangerous and

must be repaired.

19. Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing

accessories, or storing power tools. Such

preventive safety measures reduce the risk of

starting the power tool accidentally.

20. Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool. Power tools are

dangerous in the hands of untrained users.

21. Maintain power tools. Check for misalignment

or binding of moving parts, breakage of parts

and any other condition that may affect the

power tool's operation. If damaged, have the

power tool repaired before use. Many accidents

are caused by poorly maintained power tools.

22. Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

23. Use the power tool, accessories and tool bits

etc. in accordance with these instructions,

taking into account the working conditions

and the work to be performed. Use of the power

tool for operations different from those intended

could result in a hazardous situation.

Service

24. Have your power tool serviced by a qualified

repair person using only identical replacement

parts. This will ensure that the safety of the power

tool is maintained.

25. Follow instruction for lubricating and

changing accessories.

26. Keep handles dry, clean and free from oil and

grease.

USE PROPER EXTENSION CORD. Make sure your

extension cord is in good condition. When using an

extension cord, be sure to use one heavy enough to

carry the current your product will draw. An undersized

cord will cause a drop in line voltage resulting in loss of

power and overheating. Table 1 shows the correct size to

use depending on cord length and nameplate ampere

rating. If in doubt, use the next heavier gage. The smaller

the gage number, the heavier the cord.

Table 1: Minimum gage for cord

Ampere Rating

Volts

Total length of cord in feet

More Than Not More Than

120V 25 ft. 50 ft. 100 ft. 150 ft.

AWG

06

6

10

12

10

12

16

18

16

14

16 16 14

1416

16

12

14

12

Not Recommended

220V - 240V 50 ft. 100 ft. 200 ft. 300 ft.

000300

GEB016-3

JIG SAW SAFETY WARNINGS

1. Hold power tool by insulated gripping

surfaces, when performing an operation

where the cutting accessory may contact

hidden wiring or its own cord. Cutting

accessory contacting a "live" wire may make

exposed metal parts of the power tool "live" and

could give the operator an electric shock.

2.

Use clamps or another practical way to secure

and support the workpiece to a stable platform.

Holding the work by hand or against your body

leaves it unstable and may lead to loss of control.

3. Always use safety glasses or goggles.

Ordinary eye or sun glasses are NOT safety

glasses.

4. Avoid cutting nails. Inspect workpiece for any

nails and remove them before operation.

4

5. Do not cut oversize workpiece.

6. Check for the proper clearance beyond the

workpiece before cutting so that the blade will

not strike the floor, workbench, etc.

7. Hold the tool firmly.

8. Make sure the blade is not contacting the

workpiece before the switch is turned on.

9. Keep hands away from moving parts.

10. Do not leave the tool running. Operate the tool

only when hand-held.

11. Always switch off and wait for the blade to

come to a complete stop before removing the

blade from the workpiece.

12. Do not touch the blade or the workpiece

immediately after operation; they may be

extremely hot and could burn your skin.

13. Do not operate the tool at no-load

unnecessarily.

14. Some material contains chemicals which may

be toxic. Take caution to prevent dust

inhalation and skin contact. Follow material

supplier safety data.

15. Always use the correct dust mask/respirator

for the material and application you are

working with.

SAVE THESE INSTRUCTIONS.

WARNING:

DO NOT let comfort or familiarity with product

(gained from repeated use) replace strict adherence

to safety rules for the subject product. MISUSE or

failure to follow the safety rules stated in this

instruction manual may cause serious personal

injury.

USD201-2

Symbols

The followings show the symbols used for tool.

󺹮 volts

󺹮 amperes

󺹮 hertz

󺹮 alternating current

󺹮 no load speed

󺹮 Class II Construction

󺹮 revolutions or reciprocation per minute

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and

unplugged before adjusting or checking function on

the tool.

Selecting the cutting action

1

011956

This tool can be operated with an orbital or a straight line

(up and down) cutting action. The orbital cutting action

thrusts the blade forward on the cutting stroke and

greatly increases cutting speed.

To change t he cu ttin g a ction, jus t t ur n the c ut ti ng act io n

changing lever to the desired cutting action position.

Refer to the table to select the appropriate cutting action.

Position

Cutting action

Applications

For cutting mild steel,

stainless steel and plastics.

For clean cuts in wood

and plywood.

Small orbit

cutting action

For cutting mild steel,

aluminum and

hard wood.

For cutting wood and

plywood.

For fast cutting in aluminum

and mild steel.

Large orbit

cutting action

For fast cutting in wood

and plywood.

0

Straight line

cutting action

Medium orbit

cutting action

006582

Switch action

1

2

011957

1. Switch trigger

2. Lock button

1. Cutting action

changing lever

5

CAUTION:

• Before plugging in the tool, always check to see

that the switch trigger actuates properly and returns

to the "OFF" position when released.

• Switch can be locked in "ON" position for ease of

operator comfort during extended use. Apply

caution when locking tool in "ON" position and

maintain firm grasp on tool.

To s ta rt th e tool, sim pl y pull th e swi tc h tr ig ge r. R elease

the switch trigger to stop.

For continuous operation, pull the switch trigger and then

push in the lock button.

To st op the to ol from th e lo cked position, pull the switch

trigger fully, then release it.

Speed adjusting dial

1

011958

The tool speed can be infinitely adjusted by turning the

speed adjusting dial. Higher speed is obtained when the

speed adjusting dial is turned in the direction of number

5; lower speed is obtained when it is turned in the

direction of number 1.

Refer to the table to select the proper speed for the

workpiece to be cut. However, the appropriate speed

may differ with the type or thickness of the workpiece. In

general, higher speeds will allow you to cut workpieces

faster but the service life of the blade will be reduced.

Number on adjusting dial

4 - 5

Mild steel 3 - 5

Stainless steel 3 - 4

Aluminum 3 - 5

Plastics 1 - 4

Workpiece to be cut

Wood

006368

CAUTION:

• The speed adjusting dial can be turned only as far

as 5 and back to 1. Do not force it past 5 or 1, or the

speed adjusting function may no longer work.

ASSEMBLY

CAUTION:

•

Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Installing or removing saw blade

CAUTION:

• Always clean out all chips or foreign matter

adhering to the blade and/or blade holder. Failure

to do so may cause insufficient tightening of the

blade, resulting in a serious personal injury.

• Do not touch the blade or the workpiece

immediately after operation; they may be extremely

hot and could burn your skin.

• Use only B type blades. Using blades other than B

type blades causes insufficient tightening of the

blade, resulting in a serious personal injury.

• When you remove the saw blade, be careful not to

hurt your fingers with the top of the blade or the tips

of workpiece.

1

2

3

4

011959

1

012053

Before installing the blade, make sure that the blade

clamp lever is in the released position.

To i ns ta ll th e blade, ins er t t he b la de ( teet h fac in g f orwa rd )

into the blade holder until it latches. The lever moves to

1. Blade clamp

lever

1. Blade holder

2. Blade

3. Fixed position

4. Released

position

1. Speed adjusting

dial

6

the fixed position by itself and the blade is locked. Pull

the blade lightly to make sure that the blade does not fall

off during operation.

CAUTION:

• If the lever does not move to the fixed position by

itself, the blade is not installed completely. Do not

press the lever by hand to the fixed position. It may

damage the tool. Make sure that the back edge of

the blade fits into the roller.

To r em ove th e bla de , pu sh the le ve r f orw ard as f ar as it

will go. This allows the blade to be released.

Hex wrench storage

1

2

011960

When not in use, store the hex wrench as shown in the

figure to keep it from being lost.

OPERATION

CAUTION:

• Always hold the base flush with the workpiece.

Failure to do so may cause blade breakage,

resulting in a serious injury.

• Advance the tool very slowly when cutting curves or

scrolling. Forcing the tool may cause a slanted

cutting surface and blade breakage.

• Hold the tool firmly with one hand on the main

handle when performing the tool. If necessary, the

front part of the tool may be supported by the other

hand.

Turn the tool on without the blade making any contact

and wait until the blade attains full speed.

1

2

011961

Then rest the base flat on the workpiece and gently move

the tool forward along the previously marked cutting line.

Bevel cutting

011962

CAUTION:

• Always be sure that the tool is switched off and

unplugged before tilting the base.

With the base tilted, you can make bevel cuts at any

angle between 0° and 45° (left or right).

1

2

3

011963

Loosen the bolt on the back of the base with the hex

wrench. Move the base so that the bolt is positioned in

the center of the cross-shaped slot in the base.

1

2

011964

Tilt the base until the desired bevel angle is obtained.

The edge of the housing indicates the bevel angle by

graduations. Then tighten the bolt to secure the base.

Front flush cuts

1

2

3

011965

1. Base

2. Hex wrench

3. Bolt

1. Edge

2. Graduation

1. Hex wrench

2. Bolt

3. Base

1. Cutting line

2. Base

1. Wrench holder

2. Hex wrench

7

Loosen the bolt on the back of the base with the hex

wrench and slide the base all the way back. Then tighten

the bolt to secure the base.

Cutouts

Cutouts can be made with either of two methods A or B.

A) Boring a starting hole

1

011966

For internal cutouts without a lead-in cut from an edge,

pre-drill a starting hole 12 mm (1/2") or more in diameter.

Insert the blade into this hole to start your cut.

B) Plunge cutting

011967

You need not bore a starting hole or make a lead-in

cut if you carefully do as follows.

(1) Tilt the tool up on the front edge of the base

with the blade point positioned just above the

workpiece surface.

(2) Apply pressure to the tool so that the front

edge of the base will not move when you

switch on the tool and gently lower the back

end of the tool slowly.

(3) As the blade pierces the workpiece, slowly

lower the base of the tool down onto the

workpiece surface.

(4) Complete the cut in the normal manner.

Finishing edges

011968

To trim edges o r mak e di mensio na l adj us tmen ts, r un the

blade lightly along the cut edges.

Metal cutting

Always use a suitable coolant (cutting oil) when cutting

metal. Failure to do so will cause significant blade wear.

The underside of the workpiece can be greased instead

of using a coolant.

Dust extraction

1

011969

Clean cutting operations can be performed by connecting

this tool to a Makita vacuum cleaner. Insert the hose of

the vacuum cleaner into the hole at the rear of the tool.

Rip fence (Optional accessory)

CAUTION:

• Always be sure that the tool is switched off and

unplugged before installing or removing

accessories.

1. Straight cuts

1

011970

When repeatedly cutting widths of 160 mm or less,

use of the rip fence will assure, clean, straight cuts.

1

2

3

4

011971

To ins tall, in sert th e r ip fen ce into t he r ecta ngul ar

hole on the side of the base with the fence guide

facing down. Slide the rip fence to the desired

cutting width position, then tighten the bolt to

1. Bolt

2. Fence guide

3. Hex wrench

4. Rip fence (Guide

rule)

1. Rip fence

(Guide rule)

1. Hose

1. Starting hole

8

secure it.

2. Circular cuts

When cutting circles or arcs of 170 mm (6-11/16")

or less in radius, install the rip fence as follows.

1

2

3

4

011972

Insert the rip fence into the rectangular hole on the

side of the base with the fence guide facing up.

Insert the circular guide pin through either of the

two holes on the fence guide. Screw the threaded

knob onto the pin to secure the pin.

1

011973

Now slide the rip fence to the desired cutting radius,

and tighten the bolt to secure it in place. Then move

the base all the way forward.

NOTE:

• Always use blades No. B-17, B-18, B-26 or B-27

when cutting circles or arcs.

Anti-splintering device (Optional accessory)

1

2

011974

For splinter-free cuts, the anti-splintering device can be

used. To install the anti-splintering device, move the tool

base all the way forward and fit it from the back of tool

base. When you use the cover plate, install the

anti-splintering device onto the cover plate.

CAUTION:

• The anti-splintering device cannot be used when

making bevel cuts.

Cover plate (Optional accessory)

1

2

011975

Use the cover plate when cutting decorative veneers,

plastics, etc. It protects sensitive or delicate surfaces

from damage. Fit it on the back of the tool base.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and

unplugged before attempting to perform inspection

or maintenance.

•

Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

To main tain produ ct SA FET Y and RELI AB ILI TY, repa irs,

carbon brush inspection and replacement, any other

maintenance or adjustment should be performed by

Makita Authorized or Factory Service Centers, always

using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:

• These accessories or attachments are

recommended for use with your Makita tool

specified in this manual. The use of any other

accessories or attachments might present a risk of

injury to persons. Only use accessory or

attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

• Jig saw blades

• Hex wrench 3

• Rip fence (guide rule) set

• Anti-splintering device

• Hose (For vacuum cleaner)

• Cover plate

NOTE:

• Some items in the list may be included in the tool

package as standard accessories. They may differ

from country to country.

1. Cover plate

2. Tool base

1. Anti-splintering

device

2. Tool base

1. Rip fence (Guide

rule)

1. Threaded knob

2. Pin

3. Rip fence

(Guide rule)

4. Fence guide

9

MAKITA LIMITED ONE YEAR WARRANTY

Warranty Policy

Every Makita tool is thoroughly inspected and tested

before leaving the factory. It is warranted to be free of

defects from workmanship and materials for the period

of ONE YEAR from the date of original purchase.

Should any trouble develop during this one year period,

return the COMPLETE tool, freight prepaid, to one of

Makita’s Factory or Authorized Service Centers. If

inspection shows the trouble is caused by defective

workmanship or material, Makita will repair (or at our

option, replace) without charge.

This Warranty does not apply where:

IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY

INDIRECT, INCIDENTAL OR CONSEQUENTIAL

DAMAGES FROM THE SALE OR USE OF THE

PRODUCT. THIS DISCLAIMER APPLIES BOTH

DURING AND AFTER THE TERM OF THIS

WARRANTY.

MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED

WARRANTIES, INCLUDING IMPLIED WARRANTIES

OF "MERCHANTABILITY" AND "FITNESS FOR A

SPECIFIC PURPOSE," AFTER THE ONE YEAR TERM

OF THIS WARRANTY.

This Warranty gives you specific legal rights, and you

may also have other rights which vary from state to

state. Some states do not allow the exclusion or

limitation of incidental or consequential damages, so

the above limitation or exclusion may not apply to you.

Some states do not allow limitation on how long an

implied warranty lasts, so the above limitation may not

apply to you.

repairs have been made or attempted by others:

repairs are required because of normal wear and

tear:

the tool has been abused, misused or improperly

maintained:

alterations have been made to the tool.

EN0006-1

Page is loading ...

28

Some dust created by power sanding, sawing, grinding, drilling, and other

construction activities contains chemicals known to the State of California

to cause cancer, birth defects or other reproductive harm. Some examples

of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this

type of work. To reduce your exposure to these chemicals: work in a well

ventilated area, and work with approved safety equipment, such as those

dust masks that are specially designed to filter out microscopic particles.

WARNING

< USA only >

ADVERTENCIA

Algunos tipos de polvo creados por el lijado, serrado, amolado, taladrado, y

otras actividades de la construccion contienen sustancias quimicas

reconocidas por el Estado de California como causantes de cancer, defectos

de nacimiento y otros peligros de reproduccion. Algunos ejemplos de estos

productos quimicos son:

• plomo de pinturas a base de plomo,

• silice cristalino de ladrillos y cemento y otros productos de albanileria, y

• arsenico y cromo de maderas tratadas quimicamente.

El riesgo al que se expone variara, dependiendo de la frecuencia con la que

realice este tipo de trabajo. Para reducir la exposicion a estos productos

quimicos: trabaje en un area bien ventilada, y pongase el equipo de seguridad

indicado, tal como esas mascaras contra el polvo que estan especialmente

disenadas para filtrar particulas microscopicas.

< USA solamente >

Makita Corporation

3-11-8, Sumiyoshi-cho,

Anjo, Aichi 446-8502 Japan

www.makita.com

885031A945 JV0600-1

Makita JV0600 User manual

Makita JV0600 User manual

in other languages

Related papers

Other documents