Creative DTT 3500 Digital User manual

Brand: Creative

Model: DTT 3500 Digital

Type: User manual

This manual is also suitable for

DTT3500 Digital

User’s Guide

DTT3500 Digital

Information in this document is subject to change without notice and does not represent a commitment on the part of Creative Technology Ltd. No part of this manual may be

reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, for any purpose without the written permission of

Creative Technology Ltd. The software described in this document is furnished under a license agreement and may be used or copied only in accordance with the terms of the

license agreement. It is against the law to copy the software on any other medium except as specifically allowed in the license agreement. The licensee may make one copy of

the software for backup purposes.

Version 1.0

August 2000

Inc., Newton, MA. The Creative logo, Sound Blaster and the Sound Blaster logo are registered trademarks, and EAX, the EAX logo, PC-DVD, CMSS, Live! and Creative Multi

Speaker Surround are trademarks of Creative Technology, Ltd in the United States and/or other countries. NOMAD is a registered trademark of Aonix and is used by Creative

Technology and/or its affiliates under license. The DTT3500 Digital’s Dolby Digital decoder/amplifier is manufactured under license by Dolby Laboratories. Dolby, Dolby

rights reserved. Sony is a registered trademark and PlayStation 2 is a trademark of Sony Computer Entertainment Inc. Microsoft and DirectSound are registered trademarks of

Microsoft Inc. All other brand and product names are trademarks or registered trademarks of their respective holders.

All specifications are subject to change without prior notice. Actual contents may differ slightly from those pictured.

Safety & Regulatory Information

The following sections contain notices for various countries:

CAUTION: This device is intended to be installed by the user in a CSA/TUV/UL certified/listed IBM AT or

compatible personal computers in the manufacturer’s defined operator access area. Check the equipment operating/

installation manual and/or with the equipment manufacturer to verify/confirm if your equipment is suitable for user-

installed application cards.

Modifications

Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to

operate the device.

Compliance

This product conforms to the following Council Directive:

❑

Directive 89/336/EEC, 92/31/EEC (EMC) 72/23/EEC (LVD)

Important Notice

The serial number for the

DTT3500 Digital

is located on the subwoofer. Please write this number down and keep it

in a secure area. This is for your security.

WARNING: To prevent fire or

shock hazard, do not expose this

appliance to rain or moisture.

IMPORTANT SAFETY INSTRUCTIONS

READ INSTRUCTIONS - All safety and

operating instructions should be read

before the DTT3500 Digital amplified

subwoofer/satellite system is operated.

RETAIN INSTRUCTIONS - The safety and

operating instructions should be retained

for future reference.

HEED WARNINGS - All warnings on the

subwoofer and in the operating instructions

should be adhered to.

FOLLOW INSTRUCTIONS - All operating and

use instructions should be followed.

CLEANING - Unplug the subwoofer from the

wall outlet or other power source before

cleaning. Do not use liquid cleaners or aerosol

cleaners. Use a damp cloth for cleaning.

ATTACHMENTS - Do not use attachments not

recommended by Cambridge SoundWorks

as they may cause hazards.

WATER AND MOISTURE - Do not use the

subwoofer near water—for example, near a

bath tub, wash bowl, kitchen sink, or

laundry tub; in a wet basement; or near a

swimming pool; and the like.

ACCESSORIES - Do not place the DTT3500

Digital system on an unstable cart, stand,

tripod, bracket, or table. The subwoofer or

satellites may fall, causing serious injury to

a child or adult, and serious damage to the

product. Use only with a cart, stand, tripod,

bracket, or table recommended by

Cambridge SoundWorks, or sold with the

product. Any mounting of the satellites or

subwoofer should follow the

manufacturer’s instructions, and should use

a mounting accessory recommended by

Cambridge SoundWorks.

VENTILATION - Slots and openings in the

cabinet are provided for ventilation, to

ensure reliable operation of the subwoofer

and to prevent it from overheating; and

these openings must not be blocked or

covered. The openings should never be

blocked by placing the product on a bed,

sofa, rug, or other similar surface. The

subwoofer should not be placed in a built-in

installation such as a bookcase or rack

unless proper ventilation is provided or

Cambridge SoundWorks’ instructions have

been adhered to.

HEAT - The subwoofer should be situated

away from heat sources such as

radiators, heat registers, stoves, and

other products (including amplifiers) that

produce heat.

POWER SOURCES - The subwoofer should

be operated only from the type of power

source indicated on the marking label. If

you are not sure of the type of power supply

to your home, consult your product dealer

or local power company. For products

intended to operate from battery power or

other sources, refer to the operating

instructions.

POLARIZATION - The subwoofer may be

equipped with a polarized alternating-

current line plug (a plug having one blade

wider than the other). This plug will fit into

the power outlet only one way. This is a

safety feature. If you are unable to insert

the plug fully into the outlet, try reversing

the plug. If the plug should still fail to fit,

contact your electrician to replace your

obsolete outlet. Do not defeat the safety

purpose of the polarized plug.

POWER-CORD PROTECTION - Power-supply

cords should be routed so that they are not

likely to be walked on or pinched by items

placed upon or against them, paying

particular attention to cords at plugs,

convenience receptacles, and the point

where they exit from the subwoofer.

LIGHTNING - For added protection for the

DTT3500 Digital system during a lightning

storm, or when it is left unattended and

unused for long periods of time, unplug it

from the wall outlet. This will prevent

damage to the subwoofer due to lightning

and power-line surges.

OVERLOADING - Do not overload wall outlets,

extension cords, or integral convenience

receptacles as this can result in a risk of fire

or electric shock.

OBJECT AND LIQUID ENTRY - Never push

objects of any kind into the subwoofer

through openings as they may touch

dangerous voltage points or short out parts

that could result in a fire or electric shock.

Never spill liquid of any kind on the

subwoofer.

SERVICING - Do not attempt to service the

subwoofer yourself as opening or removing

covers may expose you to dangerous

voltage or other hazards. Refer all servicing

to qualified service personnel.

DAMAGE REQUIRING SERVICE - Unplug

the subwoofer from the wall outlet or other

power source and refer servicing to

qualified service personnel under the

following conditions:

a) When the power-supply cord or plug is

damaged.

b) If liquid has been spilled, or object have

fallen into the subwoofer.

c) If the subwoofer has been exposed to rain

or water.

d) If the subwoofer does not operate normally

by following the operating instructions; or

exhibits a distinct change in performance.

e) If the product has been dropped or

damaged in any way.

REPLACEMENT PARTS - When replacement

parts are required, be sure the service

technician has used replacement parts

specified by Cambridge SoundWorks or

have the same characteristics as the

original part. Unauthorized substitutions

may result in fire, electric shock, or other

hazards.

SAFETY CHECK - Upon completion of any

service or repairs to the DTT3500 Digital

system, ask the service technician to

perform safety checks to determine that the

DTT3500 Digital system is in proper

operating condition.

WALL OR CEILING MOUNTING - The

DTT3500 Digital satellites should be

mounted to a wall or ceiling only as

recommended by Cambridge SoundWorks.

DTT3500 Digital

Contents

Introduction

................................................................................................ 5

Inventory.................................................................................................. 6

Recommended Signal Sources................................................................. 6

Installation Sequence............................................................................... 7

Speaker System Connections................................................................... 7

Speaker System Connection Diagram ..................................................... 8

Signal Source Connections ...................................................................... 9

Signal Source Connection Diagram....................................................... 10

Speaker Cable and Stand Installation .................................................... 11

Mounting Speakers ................................................................................ 12

Speaker Placement................................................................................. 13

Decoder Amplifier Placement ............................................................... 16

Decoder Amplifier Functions ................................................................ 17

Surround Reference ............................................................................... 19

Multiple Connections............................................................................. 21

Applications Guide ................................................................................ 22

Playback Levels ..................................................................................... 25

Specifications......................................................................................... 25

EAX ....................................................................................................... 25

Technical Support.................................................................................. 27

Limited Warranty................................................................................... 30

Thank you for purchasing DTT3500

Digital by Cambridge SoundWorks.

DTT3500 Digital lets you experience

the full potential of Dolby Digital

multichannel sound from your DVD

player or game console, with a

dynamic output that rivals a

component home theater system. It

processes both Dolby Digital and

Dolby Surround program material.

DTT3500 Digital includes an

OPTICAL connection to enhance the

connectivity and usability to any

devices with OPTICAL output.

DTT3500 Digital also includes a

DIGITAL DIN input which supports

discrete 5.1-channel output.

DTT3500 Digital offers up to 6-

channel discrete audio support for

Microsoft DirectSound 3D and its

other derivatives. In some of today’s

best CD-based action games,

DTT3500 Digital can decode the

Dolby Digital cut-scenes while

offering enveloping positional multi-

channel audio. It’s ready for the new

era of DVD-based games.

Also included is Creative Multi

Speaker Surround (CMSS), which

lets you hear all of your favorite

stereo program material with a new

and exciting three-dimensional

quality.

DTT3500 Digital comes equipped

with an I.R. Remote Control,

providing wireless control over a

variety of audio functions.

The Memory Retention feature of

the DTT3500 Digital system

remembers the last used user settings

in standby mode.

Introduction

Inventory

Recommended Signal Sources

Examine each unit carefully for

shipping damage. If there is any, do not

install or use the system. For advice, call

the store where you made your purchase

or call Creative Technology Ltd. technical

support. Save the shipping carton and

inserts in case you have to transport the

system later. All of the items shown in the

illustration below should be included with

your system. If anything is missing, notify

the retailer.

The

DTT3500 Digital

supports many

signal source inputs, both analog and

digital. For example:

1. DVD players with Dolby Digital

(AC-3) optical outputs. DVD players

with coaxial outputs (for example, the

Creative labs PC-DVD Encore) may

also be used.

2. Sound cards that support

DirectSound

3D sound processing,

including front and rear 2-channel

minijack line outputs (like Sound

Blaster Live! series or Creative Labs

Sound Blaster PCI series).

Sound Blaster Live! owners should

utilize the exclusive Digital DIN

connection to hear the clearest digital

audio available.

3. Conventional 2-channel sound cards

such as Sound Blaster 16 or the

Sound Blaster AWE series can also

be used with the

DTT3500 Digital

4. Game consoles like the

PlayStation 2 using the Optical

or Analog Line In connections.

15V 4A DC

Power Adapter

Supports (6)

3m Speaker Cable

Identification Labels

Strips of Rubber Feet (2)

Screws and Plastic

Anchors (2)

Holder/Cap (2)

Frames (2)

Feet (6)

Remote Control

Support

Extends (18)

5m Speaker Cable (2)

Optical Cable

Monitor Stand

(for Center Speaker)

Desktop Stand

(for Center

Speaker)

Dual Female-to-Female

RCA Adapter

“AA”- Size Battery (2)

SPDIF Cable (RCA to RCA)

Stereo to Dual RCA Cable

SPDIF DIN Cable

Tandem Audio Cable

Decoder Amplifier

Center Speaker

Satellites (4)

Subwoofer

Desktop Stand (4)

(for Satellites)

Screw (for Center

Speaker Stands)

Minijack to DIN Cable

1. Read all of the instructions

before installing the speaker

system.

2. Attach the provided stand to the

Decoder Amplifier if you wish to

place the unit vertically. For

more details see “Decoder

Amplifier Placement” on page

16.

3. Connect the Satellites, Center

Speaker, and Subwoofer to the

Decoder Amplifier.

4. Connect the Dolby Digital

output of your digital program

source to the coaxial and/or

optical Dolby Digital input of the

Decoder Amplifier.

5. Connect your normal audio

signal sources via the Analog

Line In inputs. An owner of a

Sound Blaster Live! sound card

with a Digital DIN output should

use the supplied cable to connect

it to the Digital DIN input

instead.

6. Using the placement instructions

as a guide, position the Satellites,

the Center Speaker and

Subwoofer. Install the Desktop

Stands and Floor Stands as

appropriate. If you wish to

substitute a powered subwoofer

for the subwoofer that comes

with DTT3500 Digital, read

“Substituting a powered

subwoofer” on page 15.

7. Connect the Power Adapter to

the Decoder Amplifier.

8. Turn on the power. Use the

TEST function on the Remote

Control to position and balance

the speakers.

9. You may wish to experiment

with speaker placement briefly

before concealing the connecting

cables and making the

installation more permanent.

10. The unit is ready for you to

enjoy.

Speaker Connections

Insert one satellite’s plug into the

corresponding Speaker Output on the

Decoder Amplifier. Repeat this

process for the remaining satellites,

center speaker and subwoofer. For

more details see “Speaker Cable and

Stand Installation” on page 11.

If substituting a powered

subwoofer, connect it to the

Subwoofer Line Out. For more

details see “Substituting a powered

subwoofer” on page 15.

Power Adapter Connections

Insert the small DC connector into

the 15V DC IN jack on the back of

the Decoder Amplifier. Insert the

Power Adapter’s AC plug into an

appropriate receptacle.

Note: Set the Decoder Amplifier to

standby mode before unplugging or

turning off the power supply.

Installation Sequence

Speaker System

Connections

Front Left Satellite

Rear Left Satellite

Rear Right Satellite

Front Right Satellite

Power Adapter

Center Speaker

Subwoofer

Speaker System Connection Diagram

Dolby Digital source

Connect the Dolby Digital/SPDIF

output of your signal source to the

Decoder Amplifier’s Dolby Digital

(AC-3) / PCM Audio Inputs

COAXIAL or OPTICAL jack using

the SPDIF Cable (RCA to RCA) or

the Optical Cable.

Game consoles

Connect the optical output of the

game console (e.g. PlayStation 2) to

the OPTICAL input with the

Optical Cable.

Use the Stereo to Dual RCA

Cable and the Dual Female-to-

Female RCA Adapter to connect to

the game console’s RCA output

through the multiple A/V plug. Then

connect the miniplug end of the

Stereo to Dual RCA Cable to the

FRONT jack of the Decoder

Amplifier.

For devices with optical output

Connect the optical output of these

devices (e.g. CD or MD players) to

the OPTICAL input with the

Optical Cable.

For Sound Blaster Live! sound

cards with Digital Out output

Connect the sound card’s Digital

Out output to the

Digital DIN

input with the

Minijack to DIN

Cable

and the

SPDIF DIN

Cable

For DIN Bracket bundled

with Live! Drive IR

Connect its Digital DIN output to the

DIGITAL DIN input with the

SPDIF DIN Cable.

For all other sound cards

Use the Tandem Audio Cable.

Connect the lime-green stereo

miniplugs to the Line Out minijack

output of your sound card and to the

FRONT minijack input of the

Decoder Amplifier. Connect the

black stereo miniplugs to the Rear

Out minijack output of your sound

card (if present) and to the Rear

minijack input of the Decoder

Amplifier.

Signal Source Connections

Signal Source Connection Diagram

Dual Female-to-Female RCA Adapter

Game Console

DVD Player

CD Player

MD Player

Digital Output (Eg. PC-DVD Encore)

4-Ch Sound Card Output

(Eg. Sound Blaster Live!)

Digital Output

(Bundled with Live! Drive IR)

REAR OUT

LINE OUT

DIGITAL OUT

OPTICAL OUT-

DIGITAL OUT

Stereo to Dual RCA Cable

SPDIF Cable

(RCA to RCA)

Optical Cable

Tandem Audio Cable

SPDIF DIN Cable

2-Ch Sound Card Output

(Eg. Sound Blaster AWE64)

LINE OUT

Lime-Green

Black

Lime-Green

Black

Digital Output (Sound Blaster 5.1 Sound Card)

Minijack to DIN Cable

White

Red

COAXIAL OUTPUT

DIGITAL OUT

Speaker Cable

Installation

Typically, the 3 meter (5 feet) Speaker

Cables will connect the front Satellites

and the Center Speaker to the Decoder

Amplifier and the 5 meter (9 feet)

Speaker Cables will connect the rear

Satellites to the Decoder Amplifier. A

panel of twelve self-adhesive labels is

provided to identify each Satellite and

Subwoofer and the opposite end of the

cable connected to a Satellite and

Subwoofer.

1. Identify a 3 meter Speaker Cable.

Most often, a Satellite will be used

with a Desktop Stand. In this case,

thread the bare cable end of a 3

meter Speaker Cable through the

hole in the Desktop Stand.

Connect this end to a Satellite (as

shown in

Diagram A

). Carefully

insert the Desktop Stand’s

attachment arm into the socket in

the back of the Satellite, taking up

any slack in the cable as required.

2. To use this Satellite in the front left

position, remove the backing from

the small, round “L” label and

apply it to the back of the Satellite

(see

Diagram A

3. Remove the backing from the

remaining, longer “L” label and

wrap it around the opposite end of

the Speaker Cable near the RCA

plug.

4. Place the Satellite in the front left

position.

5. Repeat this process using another

3 meter Speaker Cable for the

front right Satellite, using the “R”

labels.

6. Connect another 3 meter Speaker

Cable to the Center Speaker. Use

the “C” (center) labels. For details

on attaching Center Speaker

stands, see “Center Speaker Stand

Installation” on page 12.

7. Use the RS and LS labels (right

and left surround) and 5 meter

Speaker Cables for the rear

Satellites.

8. If you wish to use the Floor

Stands with the rear Satellites,

assemble the stand according to

the

Floor Stand Assembly

leaflet.

9. Use the last 3 meter Speaker

Cable and the “SUB” labels for

the Subwoofer.

Speaker Cable Usage

To connect the Speaker Cable to each

speaker, press one of the spring-

loaded tabs to expose the connection

hole.

Insert the bare end of the cable into

the exposed hole, then release the tab

to lock the cable in place. Connect

cables with red bands to red tab

connectors, and unmarked wires to

black tab connectors.

Notes:

Matching red cables to red

tabs and unmarked cables to black

tabs insures the speakers all play “in

phase”. “Out-of-phase” connections

will do no electrical harm, but the

overall sound quality will be greatly

reduced. You can substitute regular

18 gauge speaker cable to create

longer cables, if needed. The 5 meter

cables may also be used for the front

satellites if required.

Speaker

Cable and

Stand

Installation

Attachment

Socket

Center Speaker Stand

Installation

Unlike the Desktop Stand (for

Satellites), the stands for the

Center Speaker are of the screw-in

type.

1. Align the Attachment Arm to

the Center Speaker (see

Diagram B).

2. Use the screw provided to

connect the Attachment Arm

to the Center Speaker.

Screw Mounting

Mounting the rear satellites on side

walls will give you superior surround

effects.

For a secure installation, mount the

rear satellites only on walls that are

structurally sound.

1. Place the following near you: rear

satellites, screws, plastic anchors

and rubber pads (supplied). You will

also need a drill and hammer.

2. Mark the wall where each rear

satellite screw will be. Position

the speakers behind you and

slightly above ear level.

3. Drill a hole about 2 cm (1 inch)

deep into each wall. Tap a plastic

anchor into the hole until it is

flush with the wall (see Diagram

C).

4. Screw a M5 x 25 mm screw into

each anchor, leaving about

0.5 cm (¼ inch) of the screw

protruding.

5. Apply four rubber pads on the

corners at the back of each rear

satellite. The rubber pads will

cushion the satellites from any

vibration and help keep them in

position.

6. Slip the keyhole of each rear

satellite onto a protruding screw

to complete the installation.

Attachment Arm

Mounting Speakers

The Front Satellites

The left front and right front

Satellites play stereo music, the off-

screen sounds of video playback and

the front channels of 4-channel

games.

These Satellites should be placed

to the sides of your T.V. or monitor.

Try to form an equilateral triangle

with your head and the satellites (see

Diagram D). Be sure to have a clear

line of sight from your listening

position to these Satellites.

Install the Satellite’s Desktop

Stands when using them on the

desktop, see “Speaker Cable and

Stand Installation” on page 11.

The Center Speaker

The Center Speaker provides the on-

screen effects and dialog in Dolby

Digital, Dolby Surround or Creative

Multi Speaker Surround modes. It

should be placed as close to the

center of your T.V. or monitor as

possible.

There are many mounting

possibilities. The Center Speaker can

be placed on top of the T.V or

monitor by using the provided

Monitor Stand. It directs the sound

down towards the listener (see

Diagram E).

Use the Center Speaker Desktop

Stand to position a Center Speaker in

front of the T.V. or monitor. It directs

the sound up towards the listener (see

Diagram F).

Speaker Placement

E F

The Rear Satellites

The rear Satellites provide the

surround effects in Dolby Digital,

Dolby Surround or Creative Multi

Speaker Surround modes. They also

produce the discrete rear sounds of

4-channel sound cards.

5 meters (16 feet) of cable is

provided with the two remaining

Satellites for more flexibility in rear

channel placement. The rear

Satellites may be placed in any

convenient sites alongside the

listener, including sites slightly

forward of the listening location. The

rear Satellites do not have to be at

exactly the same height as the front

Satellites.

If you have side walls close to your

listening position, excellent

placement for the rear Satellites is

slightly behind your listening

position, slightly above ear level (see

Diagram G). The Satellites may be

hung on the wall using the Screw and

Wall Anchors provided, see

“Mounting Speakers” on page 12.

Any rear Satellite placement to the

left and right side of the listening

position will also provide strong

directional and surround effects.

The rear Satellites may be installed

on their convenient Floor Stands.

The stands should be positioned to

the left and right of your listening

position (see Diagram H).

Larger T.V. consoles or desktops

can accommodate both front and

surround pairs of Satellites. Try the

extreme corners of a console or desk

using the Desktop Stands (see

Diagram I).

After you have positioned the rear

Satellites, use the TEST function on

the Remote Control to make sure

each speaker can be heard clearly.

The Subwoofer

The Subwoofer’s optimum position

is on the floor against the wall. The

closer the Subwoofer is to a corner,

the stronger the maximum bass

output. We strongly recommend

placing the Subwoofer on the floor

(see Diagram J). Leave at least 5 cm

(2 inches) of space between the

Subwoofer face and a wall. Position

the Subwoofer so that it’s connection

panel is facing a wall, shielded from

inadvertent contact. The Subwoofer

is not magnetically shielded, so

position it at least 46 cm (18 inches)

away from the T.V. or computer

monitor.

Substituting a powered

subwoofer

You may substitute a powered

subwoofer for the subwoofer that

comes with the DTT3500 Digital.

Connect its line level input (typically

an RCA jack) to the dedicated

Subwoofer Line Out on the back of

the Decoder Amplifier, using a

shielded audio cable with RCA plugs

on each end. Refer to the powered

subwoofer’s User Manual for

adjustment procedures.

The Decoder Amplifier can be

placed on the desktop, a shelf or any

site that makes the controls

convenient.

The Power Adapter cord must be

able to reach from the Decoder

Amplifier back panel to your AC

power receptacle.

Place the Decoder Amplifier on a

hard, flat surface.

There are ventilation slots on the

Decoder Amplifier’s enclosure. Do

not block these ventilation slots by

placing materials over them.

Model Variations

There are two models of the Decoder

Amplifier.

If you have purchased the

horizontal version please ignore the

following sections. Other than the

changeable face plate feature, all

functions remain the same.

The changeable face plate version

is supplied with mylar sheets which

enable you to choose a different

design or orientation (horizontal or

vertical).

Decoder Amplifier Stand

If placing the unit vertically, attach

the provided stand to the base of the

Decoder Amplifier (see Diagram

K).

Face Plate Installation

The face of the front panel may be

changed to reflect a different design

or orientation. Remove the clear

plastic cover and replace the

underlying mylar sheet with

another of your choice, (see

Diagram K). Replace the cover.

Horizontal Placement

Place the Decoder Amplifier

horizontally if there is adequate

desktop space, (see Diagram L).

Vertical Placement

If your desktop space is limited you

may choose to place the Decoder

Amplifier vertically, (see Diagram

M).

Stand

Mylar Sheet

Front Panel

Decoder Amplifier Placement

The Standby LED lights up when the Power

Adapter is connected to the mains. Press the

Power button to turn on the Decoder

Amplifier.

The CMSS Music LED will

remain illuminated after initial start-

up. The last used CMSS mode’s light

will illuminate for subsequent start-

ups from system standby mode.

The Optical LED also lights up

after initial start-up. The last used

Dolby Digital/PCM Audio input’s

light will illuminate for subsequent

start-ups from system standby mode.

The Digital DIN or Line In LED

lights up, depending on whether

Digital DIN or Analog Line In is

connected. The Digital DIN LED

will blink if a PC connected to the

Decoder Amplifier is off but a

Digital DIN input is connected.

Turning on your PC stops the LED’s

blinking.

The indicator light for Dolby

Digital will illuminate automatically

if a Dolby Digital program is

playing. That is, when a Dolby

Digital signal passes through the

Decoder’s processor via the

Optical,Coaxial or Digital DIN

(Dolby Digital/PCM Audio) inputs.

POWER

Sets the system to

“On” or standby. When set to

“On”, the Standby LED above

the power button turns off.

2. SUBWOOFER, CENTER

AND SURROUND: These

controls adjust the level of the

indicated channels. Their output

level should be balanced with the

fixed output level of the Left and

Right front Satellites.

MASTER

Adjusts the volume

of the entire system. The Master

volume knob is servo controlled

via the Remote Control.

CMSS

(Creative

Multi Speaker Surround)

processes analog program

material. Repeated presses of

this button step through four

different operation modes.

MOVIE: Creates a 5.1 speaker

soundfield appropriate for movie

or game enjoyment from an

analog sound source.

Decoder Amplifier Functions

Legend

Button

LED

MUSIC: Creates a 5.1 speaker

soundfield appropriate for music

from any analog sound source.

FOURPOINT/5.1 DIN: Use

this mode for DVD games

having Dolby Digital

soundtracks with EAX or

Microsoft DirectSound3D for

real-time positioning of sound

effects. Typically a Dolby Digital

5.1-channel + analog signal

source.

If a signal source is connected to

the Analog Line In minijacks, 4.1-

channel output is produced.

If the signal source is connected to

the Digital DIN input, up to 5.1-

channel output is produced.

Typically when using a Sound

Blaster Live! 5.1 sound card or the

DIN bracket bundled with Live!

Drive IR. For more details, see

“Signal Source Connection

Diagram” on page 10.

The DIN LED blinks if no signal

or an invalid audio signal like an

AC-3 signal is detected. In the case

of an AC-3 signal, select Digital

DIN at the Dolby Digital/PCM

Audio input selection.

STEREO: Use this mode when you

want to hear just stereo effects or the

stereo Dolby Digital downmix of a

DVD. The Dolby Surround Pro

Logic processor is disabled in this

mode.

5. DOLBY DIGITAL /PCM

AUDIO: Use this button to

select the signal source input.

Repeated presses of the button

cycles between Optical, Coaxial,

Digital DIN and Off.

MULTI-CHANNEL:

Use

this button to select the signal

source input. Repeated presses of

the button cycle between Line In,

Digital DIN and Off.

AUDIO MODE

Use this

button to play just the left or

right channels of a stereo digital

signal (PCM from an audio CD,

a Video CD or a stereo signal

from a DVD). Use this when, for

example, a Video CD has

different languages on the left

and right channels.

Repeated presses of the button

select which channel is fed to both

the Left and Right front speakers.

LL-Left channel program is directed

to both Left and Right front

speakers.

RR-Right channel program is

directed to both Left and Right front

speakers. See “Audio Mode

Selection” on page 20 for further

information about this feature.

8. DOLBY PRO LOGIC: This

button cycles from Dolby Pro

Logic processing of the digital

input to Dolby Pro Logic

processing of the analog input,

then to no Pro Logic processing.

9. DOLBY DIGITAL: This light

turns on whenever a Dolby

Digital signal is detected at the

SPDIF input of the DTT3500

Digital. For Dolby Digital 5.1

sound reproduction, make sure

only this light is illuminated.

10.

MUTE

Mutes all output from

the DTT3500 Digital. Press the

button once to mute. The blue

LED on the Master volume knob

blinks and all functions are

operable except speaker test.

Press a second time to restore

audio output. After being muted

for more than thirty minutes, the

Decoder Amplifier goes to

standby mode and the Standby

LED lights up.

11.

TEST

Press this button to start

the “test sound” generator. Use

this test sound to position all the

speakers and to balance their

relative output.

The test sound moves in sequence

from the left Satellite, the Center

Speaker, the right Satellite, then to

the rear right Satellite, rear left

Satellite and the subwoofer. All

indicator lights will blink on and off

while the test sound generator is in

operation.

The test sound will operate for

three complete cycles and then stop.

You can terminate the sound at any

point by pressing the Test button

again.

First use the test sound to verify

that each speaker is operating.

Then make sure the speakers are

positioned so that the test sound can

be clearly heard.

Finally, adjust the front panel level

controls for the Center, Subwoofer

and rear Satellites. Adjust each

control so its speaker achieves a

balanced output level with the left

and right satellites (which provide a

fixed “reference” output level).

All functions except for the level

controls are disabled while the test

sound is running.

The speaker level controls operate

at all times. If desired, you may

adjust these controls during program

material to fine-tune the balance.

(This function is only available on

the Remote Control)

Note: Volume levels during the test

sequence are lower than during

normal operation.

12.

DYNAMIC MODE:

Press

this button to experience the full

dynamic range of Dolby Digital

programs. The LEDs on the

upper half of the Decoder

Amplifier light up momentarily.

The program source will sound

louder in Dynamic Mode. If you

press this button again, the

default mode (compressed)

resumes. The LEDs on the lower

half of the Decoder Amplifier

light up momentarily.

(This function is only available

on the Remote Control)

Dolby Digital

Dolby Digital (earlier called AC-3)

delivers five discreet full-range

channels (left front, center, right

front, left surround and right

surround) plus a separate Low

Frequency Effects (LFE) channel.

Many soundtracks on the latest

generation laser discs, DVDs and

High Definition Television (HDTV),

are encoded with Dolby Digital

technology.

When a 5.1-channel Dolby Digital

program source is playing, such as

from a Creative PC-DVD player,

DVD player or game console, the

Dolby Digital indicator light will

illuminate automatically.

Note: Not every section of a DVD

will be 5.1-channel encoded. On

many DVDs, only the main movie

program will be available in 5.1-

channel sound. Other supporting

chapters (like a “Director’s

Comment” section) may be in stereo

or mono. These sections will not

light the Dolby Digital indicator even

though the sound will be properly

reproduced by the DTT3500 Digital.

Dolby Pro Logic

Dolby Surround is an earlier

surround sound standard which is

decoded with a Pro Logic processor

in the DTT3500 Digital. The Pro

Logic steering circuitry derives

separate center and rear channels

from encoded stereo program

sources.

Pro Logic processing provides a

convincing movie soundfield when

the material is specifically encoded

for Dolby Surround. Most older

stereo movie soundtracks will only

be encoded for Dolby Surround,

even though the program source may

be a DVD’s digital output. Most

DVDs containing Dolby Surround

program material will cause both the

Dolby Digital and Dolby Pro Logic

lights to illuminate. DTT3500

Digital will decode these digitally

transferred Dolby Surround

programs through the digital Pro

Logic decoder automatically.

CD-ROMs and CDs with Dolby

Surround encoding will feature the

Dolby Surround logo at the

beginning of the program or on the

packaging.

Process these programs by

selecting Analog In using the Dolby

Pro Logic button for input through

Analog Line In.

If using Digital DIN input, ensure

that the Digital DIN on the Dolby

Digital/PCM Audio input is selected.

Then select Digital In using the

Dolby Prologic button.

When Dolby Pro Logic is selected

CMSS is turned off. To turn on

CMSS again, turn off Dolby Pro

Logic first.

Do not select a Pro Logic decoding

mode if the program material is not

encoded for Dolby Surround.

Excessive center channel output will

result, and most of the stereo effect

will be lost. Use CMSS “Movie” or

“Music” modes to upmix stereo

programs to a realistic 5.1-channel

sound field.

Surround Reference

Creative Multi Speaker

Surround (CMSS)

CMSS is a 2-channel to 5.1-channel

sound processor similar in some

aspects to a Dolby Surround Pro

Logic processor.

The Music mode creates a

convincing 5.1-channel surround

soundfield with typical stereo

sources, whether they are Dolby

Surround-encoded or not. It works

well with Dolby Pro Logic, WAVE,

AVI and MIDI program material. In

essence, CMSS Music mode puts

you “on the stage” for the music’s

performance, surrounding you with

the performers.

In a similar manner, Movie mode

provides the sonic impression of

being front and center at a movie

screening. Dialog and all normally

centered sounds from a stereo

program are heard through the center

speaker. Use this mode whenever a

music program has sounds you want

to blend with on-screen action or

dialog.

Unlike Pro Logic decoding, CMSS

Music, Movie and FourPoint/5.1

DIN modes are appropriate for use

with multi-coded sources such as

DVD games. In some game titles, the

movie sequences may be encoded in

Dolby Surround but the game

sequences may be in the WAV

format. CMSS Movie mode supports

5.1-channel output for .WAV, .AVI,

.MIDI and other audio software

formats. Few, if any of these kinds of

formats are Dolby Surround

encoded.

The FourPoint/5.1 DIN mode

passes the four discreet channel

audio of 4-channel games direct to

each satellite channel. It does not

synthesize rear channel output, so

stereo signal in this mode will play

just through the front two speakers

and subwoofer.

The STEREO mode plays the Left

and Right Front speakers and the

subwoofer. It also lets you hear the

stereo downmix from any DVD.

The Dolby Pro Logic processor is

disabled in this mode.

Audio Mode Selection

The stereo soundtracks of some

movies on Video CDs (VCD format)

contain different languages. For

example, a 2-channel soundtrack

may contain Mandarin on the right

channel and English on the left

channel. The VCD program

literature should indicate the

presence of dual-language

soundtracks. Similarly, some movies

in the DVD format will contain dual-

language soundtracks. DTT3500

Digital lets you select one of these

languages and play it through both

the Left and Right speakers.

If there is no indication of which

channel is which, and you hear two

different language soundtracks

during stereo playback, select the

“LL” and “RR” settings until you

find the language soundtrack you

want.

The Audio Mode selection feature

can only be used with the PCM

digital soundtrack of a Video CD or

DVD with a dual soundtrack, not a

DVD encoded with Dolby Digital

5.1 sound or Dolby Surround-

encoded material. If you have an

analog program with separate left

and right channels (the analog output

of a CD ROM, or the analog stereo

output of a “software” Video CD, for

instance), you will have to use the

balance control in your PC’s audio

software to mute the undesired

channel.

Page is loading ...

Creative DTT 3500 Digital User manual

Brand: Creative

Model: DTT 3500 Digital

Type: User manual

This manual is also suitable for

DTT3500 Digital

Download PDF

report

Creative DTT 3500 Digital User manual

This manual is also suitable for

Creative DTT 3500 Digital User manual

Related papers

Other documents