Electrolux 9CHG584138 User manual

Brand: Electrolux

Model: 9CHG584138

Category: Cookers

Type: User manual

thermaline S90

PASTA COOKER, GAS

PASTA COOKER POUR GAZ

Doc.

62.9680.01_UL

Edition 1

01.2006

US INSTALLATION- AND OPERATING INSTRUCTIONS page 3

FR INSTRUCTIONS D’INSTALLATION ET D’EMPLOI page 13

FOR YOUR SAFETY

Do not store or use gasoline or

other flammable vapors or liquids

in the vicinity of this or any other

appliance.

POUR VOTRE SÉCURITÉ

Ne déposez pas ou n'employez

pas l'essence ou d'autres vapeurs

ou liquides inflammables à pro-

ximité de ceci ou d'aucun autre

appareil.

WARNING

Improper installation, adjust-

ment, alteration, service or

maintenance can cause property

damage, injury or death. Read the

installation, operating and

maintenance instructions thorou-

ghly before installing or servicing

this equipment.

AVERTISSEMENT

L'installation inexacte, l'ajuste-

ment, le changement, le service

ou l'entretien peuvent causer des

blessures matériels, des domma-

ges ou la mort. Lisez les instruc-

tions d'installation, d'opération et

d'entretien complètement avant

d'installer ou entretenir cet

équipement.

INSTRUCTION

Post in a prominent location instructions to be followed if the user smells gas. Consult

the local gas supplier to obtain the information.

Présentez dans des instructions en avant d'un endroit d'être suivi si l'utilisateur sent le

gaz. Consultez le fournisseur local de gaz pour obtenir l'information.

Doc. 62.9680.01_UL

Against wall - contre une paroi

Free standing - isolé

Connections - Raccordement

Gas - Gaz

Fig.1 INSTALLATION DRAWINGS - PLANS D'INSTALLATION

Page is loading ...

GENERAL INFORMATION

62.9680.01_UL Page 3

I . GENERAL INFORMATION

1. INSTRUCTIONS FOR SAFETY AND USE

1.1 INSTALLATION AND INITIAL OPERATION

1.2 OPERATOR'S OBLIGATIONS

1.3 USE AS PRESCRIBED

1.4 SAFETY-CONSCIOUS WORKING

S The installation, adjustment and initial opera-

tion of the appliance must be carried out

according to the manufacturer's instructions

and may only be done by an authorised spe-

cialist.

S Installations for the supply of electricity and

gas must be carried out by approved special-

ists in compliance with specific national and

local regulations. They bear the responsibil-

ity.

S The installation must conform with local

codes, or in the absence of local codes, with

the National Fuel Gas Code, ANSI

Z223.1/NFPA 54, or the Natural Gas and

Propane Installation Code, CSA B1 49.1.

S The appliance and its individual shutoff valve

must be disconnected from the gas supply

piping system during any pressure testing of

that system at pressures in excess of 1/2 psi

(3.5 kPA)

S The appliance must be isolated from the gas

supply piping system by closing its individual

manual shutoff valve during any pressure

testing of the gas supply piiping system at

test pressures equal to or less than 1/2 psi

(3.5 kPA)

S The manager is responsible for ensuring that

all components relevant to safety are in per-

fect working order at all times. The operating

condition of these components must be

examined by an authorised specialist at least

once a year and any defects remedied if

required.

S The operator of this appliance is responsible

for total observation of the national regula-

tions concerning operating safety.

S Remain the manual for future reference.

S Closed containers (jars, cans, bottles, tubes,

etc.) must not be heated owing to the danger

of bursting and injuries.

S Baskets filled with food must be placed

slowly in the full water trough, so the the hot

water does not overflow. - Danger of

burning!

S Ensure that no substances are put into the

water bath that could cause excess foaming

when boiling. - Danger of burning!

S The trough heating must not be switched on

if there is no water in the trough or the water

level has fallen below the minimum level. -

Risk of fire.

S The escape of burnable gases represents a

fire and explosion hazard. Action in the case

of a gas leak and a smell of gas:

- No smoking, no fire

- Do not operate electric switches or bells.

- Do not operate the piezo igniter

- Close gas cylinder valves and the main

gas valve on the appliance.

- Ventilate the room thoroughly

- Place the leaking gas cylinders upright in

the open with valves closed.

S The waste-gas outlets of the pasta cooker

become hot. Avoid touching them.

S The waste-gas outlets of the psta cooker are

not to be covered by any objects.

S Spraying the appliance or parts of it with a

high-pressure cleaning device may cause

malfunctions and is not to be done.

S Keep the appliance area free and clear from

combustibles

S Do not obstruct the flow of combustion and

ventilation air.

S For appliances with a downpipe, the hose

should lead into a drain opening which is cov-

ered by a grating such that it cannot be

kicked or tipped, or a drain gutter should run

underneath the appliance.

S Devices on wheels set up in block

configuration must be checked before each

start-up whether the potential equalization is

connected with the neighbour equipment.

The connection may be done only by

authorized technical personnel.

S Appliances on wheels must be fastened to

the building.

GENERAL INFORMATION

Page 4 62.9680.01_UL

1.5 AFTER-SALES SERVICE AND REPAIR 2. TECHNICAL DATA

3. PACKAGING

All the packaging materials used are environmentally friendly.

They may burnt at an incineration plant or sent for recycling.

4. TESTS / CERTIFICATES

All gas appliances are tested according to the standard ANSI

Z83.11-2002 and CSA 1.8-2002 of Gas Food Service Equip-

ment.

5. SPECIFICATION PLATE

The specification plate (E) is located in each case inside and

outside on the right of the operator panel (C) (Fig. 5).

The serial number is marked on the type plate. The 8 digits

give following information:

Y last digit of the year of production

WW week of production

XXXXX running number

S In the event of a permanent fault which inter-

feres with operation, the appliance must be

switched off and disconnected from the

power supply.

S To perform maintenance and repairs contact

the factory, the factory representative or a

local service company.

S Repair, maintenance work and other adjust-

ments are only to be carried out by an

authorised specialist. The valid local and

national regulations must be observed. This

applies especially to burners, ignition, safety

and control elements. Parts requiring

replacement are only to be replaced by origi-

nal spare parts. Periodic tests for gas leaks

must be carried out. A service contract is

therefore recommended.

S Cleaning and maintenance must be done

only when the heating surfaces are cold. Do

not use inflammable liquids to clean the

appliance.

S An obligatory service check is required

annually.

PNC Appliances Appliance type

Width

Depth

Height

Base

feet

height

Trough

capacity

Power

Gas

consumption

in mm in Liter

9CHG584138 WKGROFOOOO 500

900

700

200 1 x 40

14.3 kW

49000 BTU

9CHG584139 WKGROAOOOO

INSTALLATION INSTRUCTIONS

62.9680.01_UL Page 5

II . INSTALLATION INSTRUCTIONS

1. INSTALLATION

The appliance is designed for connection to fixed lines. The

appliances are suitable for setting up as single appliances or as

a group of appliances. They can be set up freely in the room,

side by side, at the side and/or at the back against a wall.

Gaps between two appliances or appliance and sidewall

should be filled with a FDA approved silicone such as Samco

RTV103.

1.1 DISTANCES

If an appliance is set up next to or against temperature-sensi-

tive furniture or similar, a safety gap of approximately 6“ (150

mm) should be maintained or some form of heat insulation fit-

ted.

The walls must be made up of non-combustible material like

tiles or steel.

1.2 HEIGHT ADJUSTMENT

Appliance on feet.

D Turn the lower part of the feed to adjust the appliance high.

The feet are adjustable from 4“ to 8“ (100 to 200 mm). A high

of 8“ (200 mm) can be recommended and results in an appli-

ance high of 35,4“ (900 mm).

Note:

Adjustment of the legs shall provide an unobstructed

clearance of minimal 6“ (150 mm) and maximal 8“ (200

mm) beneath the unit due to sanitary and stability

aspects.

The lower part of the foot must not be unscrewed too far.

The exposure of threads is prohibited.

1.3 ASSEMBLING TWO APPLIANCES

The assembly kit contains two of each of the following:

caged nuts (1 / Fig.1) pre-assembled on the right-hand side of

the appliance, hexagonal screws M8x25 (1 / Fig.1) and moun-

ting links (2 / Fig.1)

D Remove the control panels from both appliances as in 2.2

D Remove the front panels from both appliances as in 2.1

D Keeping the screw (1 / Fig.1) loose, turn it until it is approxi-

mately 5 mm deep in the caged nut.

Positioning the appliances:

D Place the appliances next to one other.

D Align for position and height.

Connect the appliances:

D Fit the mounting link (2 / Fig.1) into the inside of the second

appliance's left connecting plate.

D Tighten the screws.

Note

If required, the caged nuts can also be fitted on the other side

of the appliance.

Appliance on feet: Alignment is carried out by screwing the

lower foot parts in or out.

Appliance on

steel plinth:

Irregularities or differences in height can

be equalized by inserting one or several

strips of chrome nickel steel.

Fig.1 Lateral connection

(1)

(2)

(3b)

(3a)

(3c)

(1)

(2)

(3c)

INSTALLATION INSTRUCTIONS

Page 6 62.9680.01_UL

1.4 SIDEWALL (D)

The assembly kit contains two of each of the following:

hexagonal screws M8x25 (1 / Fig.1), bolts with retaining rings

(2 / Fig.1), mounting links (3 / Fig.1), hexagonal screws M8x16

with serrated washers and hexagonal nuts M8, hexagonal

screws M5 with serrated washers (4 / Fig.2)

and a fastening angle (5 / Fig.2).

D Insert the bolts with the retaining rings (2 / Fig.1a) from out-

side into the guide in the sidewall.

D Keeping the screw (1 / Fig.1a) loose, turn it until it is

approximately 5 mm deep in the pre-assembled caged

nuts in the sidewall.

D Attach the fastening angle (5 / Fig.2b) to the bottom of the

frame using the screws, serrated washers and nuts.

D (4 / Fig.2).

D Position the sidewall and screw it on from below using two

hexagonal screws and the serrated washers.

D Fit the mounting link (3 / Fig.1b) into the inside of the appli-

ance's connecting plate.

D Align the sidewall and firmly tighten all screws.

1.5 STEEL PLINTH

To assemble the plinth you will need:

• Right and left side plinth (1 / Fig.3).

• Plinth for the front and, for free-standing appliances, for the

rear also (2 / Fig.3).

D Push the side plinth (1 / Fig.3) onto the legs from front to

rear using the fastener. The larger gap (b / Fig.3) on the

fastener must be at the bottom.

D Affix the fasteners (3 / Fig.3) to the plinth (2 / Fig.3).

D The larger gap (b / Fig.3) on the fastener must be at the

bottom.

D Attach the plinth with the fasteners (3 / Fig.3) onto the feet.

1.6 ASSEMBLING ON CASTORS

The assembly kit for mounting on castors contains two cross

bars (2/Fig.4a) each with a fixed rear wheel (1/Fig.4a) and a

turnable front wheel (3/Fig.4a).

Mounting the castors:

D Put the appliance on supports.

D Remove the feet; each is tightened with four screws

(Fig.4b).

D Bring the two cross bars into the correct position below the

appliance and fasten it with 8 screws arrows (Fig.4a).

D Remove the supports.

D Fasten the appliance to the building. Use the hole to attach

a chain descending from the wall (arrow/Fig.4c). Making

sure the chain is shorter than the gas and electric connec-

tions.

Note:

Appliances on wheels must be secured by fasten it to the

building.

2. ACCESS TO INTERIOR

Note:

Only authorized technicians may access the interior.

Fig.2 Assemblage of sidewall

Fig. 3 Plinth assembly

()

(5)

(4)

(3c)

()

(5)

(4)

(1)

(2)

(3)

(3c)

(1)

(2)

(3)

Fig.4 Assemblage on castors

Fig. 5 General view

()

(5)

(4)

(3c)

INSTALLATION INSTRUCTIONS

62.9680.01_UL Page 7

3. FRONT PANELS (A) and (B)

D Unscrew screws (1 or 3). Also, in the case of a built-in oven,

unscrew screws (2 and/or 4) on the inside of the oven.

D Pull the panel away forwards and downwards.

3.1 CONTROL PANEL (C)

D Remove the knob.

D Loosen the screws underneath (1 / Fig.7a) and remove the

base plate.

D Loosen the screws (2 / Fig.7b) and 3 / Fig.7c)

D Remove the panel.

3.2 OVEN, STORAGE SPACE, HOT CABINET

D Remove panels A, B and C.

D Undo screws (5).

D Pull out element.

4. DOWNPIPE

Work surfaces with a downpipe (Fig.8a) have the downpipe

opening on the right-hand side of the appliance. A flexible sili-

con hose when installed in the standard manner ends under-

neath and to the right, 20 mm behind the front of the appliance

(Fig.8b).

D Alternatively, the hose can be relocated to the rear and be

routed through other pre-cut openings (Fig.8c).

Fig.6 Front panel

Fig. 7 Control panel

(1)

(3c)

(1)

(3c)

(2)

(3)

Fig. 8 Downpipe

(3c)

(1)

(3)

INSTALLATION INSTRUCTIONS

Page 8 62.9680.01_UL

5. GAS CONNECTION

The installation of the gas connection, as well as the laying of

the customer's gas line, is only to be carried out by an author-

ised specialist subject to the relevant national and local regula-

tions.

NOTE

• The gas appliance may only be installed in an adequately

ventilated location.

• Appliances are set up for natural gas. The type of gas, gas

pressure and gas category are entered on the specification

plate. Prior to connection, check that the appliance is set

up for the type of gas available on site. To do this, compare

the details on the specification plate with the existing gas

data.

• If this is not the case, the appliance must be converted or

adapted by the service personnel responsible to suit local

conditions. The following points should be noted:

- Has the appliance been tested for the new gas data?

- Conversion in accordance with the Service Manual.

- A new specification plate or a durable marking with the

new gas data must be affixed to the appliance.

5.1 CONNECTION

Gas-only appliances as well as combination electric and gas

appliances require a gas connection.

The gas connection is located under the appliance on the right

hand side. For all types the gas connection is NPT 3/4“.

The installation of a dirt trap in the gas supply line by the owner

is recommended.

After connection, all lines carrying gas must be tested for leaks

at operating pressure by painting with non-corrosive foam-

forming media, (e.g. soapy water or leak spray).

5.2 GAS PRESSURE

The current gas pressure should be measured at the Mertik

regulator with a liquid U-tube manometer (scale at least 0.1

mbar = 1 mm water column).

D Remove the control panel. The measuring nipple is located

in downwards direction at the gas supply pipe before the

two gas valves.

D Close off the mains gas leading to the appliance.

D The measuring nipple is provided at the left side of the reg-

ulator. The incoming pressure is measured in front, the out-

going pressure behind.

D Loosen the slotted screw (1 turn) in the measuring nipple.

Then connect the pressure gauge by attaching a flexible

tube to the nipple (out-side diameter 8 mm).

D Open the main gas leading to the appliance.

D Run all burners on the appliance at full output.

D Check whether the connection pressure is in permitted tol-

erance.

D Turn off the appliance again.

D Close the main gas valve.

D Retighten the slotted screw in the measuring nipple. Gas

pressure deviation tolerances are laid down by EN 203. If

the existing gas pressure is outside the given tolerances,

correct combustion can no longer be ensured. Compulsory

measures: pressure adjustment by the gas works or con-

version of the range by the service personnel. Please refer

to "Conversion to another gas type".

Gas pressure tolerances

Gas pressure variation tolerances are as

follows: mbar

Gas type Normal

pressure

Min.

pressure

inch

water g.

mbar inch

water g.

mbar

Natural gas A 7 17.4 3.5 8.7

USA

Liquid gas E 11 27.4 8.0 20

Propane

USA

INSTALLATION INSTRUCTIONS

62.9680.01_UL Page 9

6. WATER CONNECTIONS

6.1 DRINKING WATER CONNECTION

• Before connecting the appliance, flush the water pipes and

fittings and clean out any dirt.

• The appliance is designed for connection to fixed lines.

• Metal installation pipes may not protrude more than 3.9“

(10 cm) from the floor or the wall.

• The maximum water pipe pressure must not exceed 87 psi

(600 kPa).

• A mechanical filter, a shutoff valve and a non-return valve

should be built into the customer fresh water feed pipe.

• In general, all national and local water regulations must be

observed.

• The appliance is to be connected to the sanitation system

in accordance with the valid installation connection plans

and diagrams.

6.1.1 FREE-STANDING INSTALLATION

The water connections come up from the floor.

D Make corresponding openings in the base of the frame to

lead the hoses through.

D Remove front panel (B) (see Chapter 3. on page 7).

D Dismantle the storage space or hot cabinet if necessary.

D Connect the flexible hoses (5), with a G ½" inside thread,

with or without fitting a stop valve, to the customer-supplied

water pipes protruding from the floor.

6.1.2 FITTING AGAINST A WALL

The water connections come up from the floor or out of the

wall. For floor connection (see Chapter 6.1.1 on page 9).

D Pull the flexible hoses (5) out of the open rear wall and con-

nect to the customer-provided water pipes protruding from

the wall with a G ½" inside thread, with or without fitting a

stop valve.

D Position the appliance against the wall.

6.2 WASTE WATER

The appliance outlet pipe must be taken through a sufficiently

large waste water opening.

Note

Ensure accurate measurement of the waste water collecting

point and the exact positioning of the appliance.

OPERATING INSTRUCTIONS

Page 10 62.9680.01_UL

III . OPERATING INSTRUCTIONS

1. GENERAL

The Pasta Cooker is used for boiling pasta of all types, rice,

noodles, dumplings, vegetables and soups. The desired

temperature can be adjusted between 50 and 100 °C.

The water trough has a capacity of 40 litres and is operated by

a 13 kW output bar burner.

In the front part of the water trough there is a standing surface

for parking and draining off the baskets. Excess water or foam

can run off through a water overflow under the standing

surface.

The water trough is seamlessly integrated into the appliance

cover. Sharply rounded corners and edges facilitate easy

cleaning. All parts of the appliance are made of corrosion-

resistant stainless steel.

Recommended accessories:

- rectangular baskets, 1 x GN 1/1, 2 x GN 1/2 or

3 x GN 1/3

- round baskets, 3

- Base insert to stand round baskets on.

-Cover

2. OPERATION

D Turn on main gas tap (1/Fig.9).

0 = Off

1 = On

D For liquid gas operation also open the bottle or tank valve.

D Switch on gas burner (Chapters 2.1 and 2.2)

D Turn on the water supply tap (4/Fig.9) until the trough is

full.

D Switch on trough heating (Chapters 2.3 and 2.4).

D Water loss in the trough can be replaced by turning on the

tap (4/Fig.10).

The knob (2/ Fig.9) has four main settings:

2.1 IGNITING THE PILOT BURNER

D Push the knob (2/Fig.9) fully in.

D Turn it anti-clockwise to the pilot burner ignition ( )

position.

D Hold the knob (2/Fig.9) fully pressed in.

D At the same time, ignite the gas escaping at the pilot

burner with the piezo ignition device. The burner is ignited

by turning the knob (3) clockwise or anti-clockwise.

D After lighting the pilot burner, keep the rotary switch

pushed in for about 15 seconds.

It is only after this period of time that the pilot light will burn

after the rotary switch is released.

D If the pilot light extinguishes, repeat the whole process.

2.2 IGNITING THE MAIN BURNER

D Press the knob (2/Fig.9) in lightly and turn it from the pilot

burner ignition position ( ) anti-clockwise to the high ( )

position.

The high position ( ) equates to the maximum burner

power or rated thermal load.

2.3 TEMPERATURE SELECTION

The intensity of the flame can be adjusted between the "high

position" ( )and the "low position" ( ).

D Push the knob (2/Fig.9) fully in and turn it anti-clockwise

from the high setting ( ) towards the lowest ( ) setting.

The flame becomes smaller and smaller.

In the lowest setting ( ) the main burner has the lowest

output.

D To return from the lowest setting ( ) towards the highest

setting ( ), push the knob (2 / Fig.9) fully in and turn it

clockwise.

Note:

Do not switch on the trough heating or leave it switched on, if

the water level falls below the marking on the trough wall. Non-

observance of these instructions can cause severe damage to

the boiling trough and the appliance operating elements.

2.4 INITIAL OPERATION

Before initial operation of the appliance, the trough and the

baskets must be thoroughly cleaned of the protective industrial

grease by carrying out a boiling procedure without food and

with the addition of neutral soap.

2.4.1 STANDBY

The water must always be at the correct level, clean and

always able to be kept at the boil.

Check before each use:

D The water trough overflow must not be blocked.

D The operating elements must not be damaged.

1 Knob

2 Switch, Piezo ignition device

Fig.9 Control panel

Off

Igniting the pilot burner

High setting

Low setting

4 Water supply tap

5 Water drain valve

Fig.10 Front view

OPERATING INSTRUCTIONS

62.9680.01_UL Page 11

2.4.2 WORKING RULES

D Turn the switch (2/Fig.9) to the highest setting ( ).

D As soon as the water in the trough has reached boiling

point, add salt and ingredients. The use of fine salt is

recommended, to prevent corrosion of the trough base. If

this is not available, dissolve the salt beforehand in a sepa-

rate container of water.

D Place the baskets with the food to be cooked slowly in the

trough.

The overflow pipe ensures control of the maximum amount

of water and the escape of any foam that occurs during

cooking.

D Set the appropriate cooking temperature with the switch

(2/Fig.9), according to the quantity and quality of the food

to be cooked.

2.5 SWITCHING OFF THE OVEN

2.5.1 MAIN BURNER

D Turn the knob (2/Fig.9) back clockwise from the highest

setting ( ) to pilot burner ignition ( ).

The gas supply to the main burner is stopped and the main

flame is shut down. The flame of the pilot burner keeps on

burning and is available for further main burner ignitions.

2.5.2 PILOT BURNER FLAME

D Press the knob (2/Fig.9) lightly and turn it clockwise from

pilot burner ignition to Off.

The complete gas supply is cut off and the pilot light

extinguishs.

= Off

D Ignition can only start again when the heating element has

cooled down.

2.5.3 WATER DRAIN

D Drain the water from the trough by opening the water outlet

valve (5/Fig.10) (turn the handle anti-clockwise into the ver-

tical position).

D Clean any food residues from the trough and the baskets.

2.5.4 LONG SHUT-DOWNS

The following should be observed when shutting down for a

long period:

D When operating with liquid gas, also turn off the bottle or

tank valve.

D Never store the appliance where the temperature can drop

below 32°F (0 °C).

D Do not leave the troughs full of water, since this prevents

the normal passivation of the steel and the surfaces are

thus less resistant to corrosion.

D Rub all chrome nickel steel surfaces with a cloth soaked in

vaseline oil, to lay down a thin protective coating.

D Air the installation site regularly.

D Turn off the water supply.

3. CLEANING

The appliance should be cooled before every cleaning

operation.

Clean at least once daily after use:

D Shut off all the gas taps and control valves on the range.

D Drain water from the trough.

D Clean outlet nozzles with a brush.

D Remove the outlet strainer of the floor of the water trough

(snap fastening) and clean.

D Clean the outlet on the base of the trough as well as the

overflow (8) with a bottle brush.

D Using a brush, wash the water trough with hot soapy water

to which a fat-dissolving agent has been added.

D Then rinse with hot water and rub dry with a cloth or absor-

bent paper.

D Wash rust-resistant chrome nickel steel panels with hot

soapy water to which a fat-dissolving agent has been

added and rub them dry.

Water containing cooking salt or food should not dry in the boi-

ler, to prevent the danger of corrosion.

Note

D The appliance must not be sprayed with a water jet or

high-pressure cleaner.

D The floor directly in front of, near and behind the appliance

must be cleaned normally without a high-pressure cleaner.

D When cleaning the outlet pipe, do not use any sharp

objects that might damage the rubber hose.

D Never use inflammable liquids to clean the appliance

interior.

D Never use steel wool, spatulas or ordinary steel wire

brushes for cleaning the surfaces, since the deposition of

steel particles can lead to rust formation. Stainless steel

wool can possibly be used, but only in the grinding

direction.

D Never use chloric products (bleaching dye, hydrogen

chloride etc.) for cleaning chrome nickel steel, even if they

are diluted.

D Never use corrosive substances for cleaning the floor

under the appliance (e.g. hydrochloric acid). Clean the

appliance with commercial cleaning agents.

3.1 GAS BURNER

So far as is necessary, the pilot burner and main burner are

cleaned by after-sales service.

3.2 FLAME

In a visual check, the flames must be dark blue without any

upper yellow or orange tips; they must be stable and soot-free

and adhere firmly to the outlets.

If there is a lack of primary air, the flame has yellow streaks

and tips; if there is too much primary air, the flame is short,

transparent and tends to lift off the burner.

When the flame is correctly adjusted, it must not lift off or

backfire when the burner is cold as well as warm.

The flame will backfire into the inside of the burner when the

speed of the gas-air mixture through the burner outlets is too

low, particularly when the air passages are dirty.

The different ignition processes must also take place without

any delays. This concerns: ignition, arc-through and. extending

the flame over the whole burner area.

If the flame fails to meet all the requirements, cleaning or

maintenance is necessary.

OPERATING INSTRUCTIONS

Page 12 62.9680.01_UL

4. MALFUNCTION

Pasta Cooker overheats;

the power is too weak.

• Water level too low. - Top up with water.

Flame smokes. • Gas mix too rich.

• Partially blocked burner

gaps.

- Inform Customer

Service.

Long yellow flame tips • Mixing tube narrowed by

dirt.

- Inform Customer

Service.

Flame lifts off. • Exit velocity too high due

to blocked burner gaps.

• Pressure regulator on

gas cylinder not

operating correctly.

- Inform Customer

Service.

Flame flashes back. • Mixture too lean.

• Insufficient exit velocityat

burner gaps.

• Soiled airways

• Blocked nozzle.

- Inform Customer

Service.

No flame or flame too

small.

• Blocked nozzle or mixer

tube

• Blocked gas tap.

• No gas.

• Insufficient gas

pressure.

- Inform Customer

Service.

- Check gas tap setting.

No flame at low setting. • Blocked low setting

nozzle.

- Inform Customer

Service.

No flame. • Blocked burner gaps.

• Blocked nozzle.

- Clean pilot burner cap.

Flame goes out after

control valve release.

• Thermo-element

insufficiently heated

(dirty?)

• Defective thermo-

element

• Defective pilot burner

- Remove dirt; do not use

abrasive paper!

- Inform Customer

Service.

Flame too small or too

large.

• Primary air ratio

adjusted.

• Nozzle blocked.

- Inform Customer

Service.

Malfunction Possible cause Remedy

Pilot burner

Page is loading ...

62.8504.11 Table of nozzle - Tableau de gigleur

thermaline S90 Gas Pasta Cooker (14.3 kW)

Gas type

±1%

Nominal pres

sure with burner

in operation

±1%

Pressure after

the pressure

regulator with

burner in opera

tion

Category Main flame Small flame Ignitions burner

Air adjustment

Distance X

inch Water

Gauche

mbar

inch Water

Gauche

mbar in mm No. in mm No. No. No. in mm

Natural

gases

Natural

gas USA

7.0 17.4 6.0 15 A 0.116 2.95 72.7803.18 0.071 1.80 712 345064.36 0.98 25

1 106 1234

1.18 30

Liquid

gases

Propane

gas USA

11.0 27.4 10.0 25 E 0.079 2.00 72.7803.12 0.047 1.20 712 345064.21 0.94 24 1 106 1235 1.18 30

Electrolux 9CHG584138 User manual

Brand: Electrolux

Model: 9CHG584138

Category: Cookers

Type: User manual

Download PDF

report

in other languages

français: Electrolux 9CHG584138 Manuel utilisateur

Electrolux 9CHG584138 User manual

Electrolux 9CHG584138 User manual

in other languages

Related papers

Other documents