User Manual: Toshiba-TMPM330
Page | 1
TOSHIBA-TMPM330
About NGX Technologies:
NGX Technologies is a premier supplier of development tools for the ARM7, ARM Cortex M0, M3
and M4 series of microcontrollers. NGX provides innovative and cost effective design solutions
for embedded systems. We specialize in ARM MCU portfolio, which includes ARM7, Cortex-M0, M3
& M4 microcontrollers. Our experience with developing evaluation platforms for NXP controller
enables us to provide solutions with shortened development time thereby ensuring reduced time to
market and lower development costs for our customers. Our cost effective and feature rich
development tool offering, serves as a testimony for our expertise, cost effectiveness and quality.
Contact Information:
NGX Technologies Pvt.Ltd.
#39/39, 'Parusha', 1st 'E' cross,
5th Main Road, Remco Layout,
Vijayanagar 2nd Stage, Bangalore
– 560 040. Phone : +91-80-
40925507
email:s[email protected]
Table of Contents
User Manual: Toshiba-TMPM330
Page | 2
Chapter 1 : Introduction 3
Chapter 2: CoFlash Installation & Flashing Binary codes 3
2.1 Installation & Configuration of CoFlash software 3
2.2 Flashing Binary Codes in CoFlash. 6
Chapter 3 : TMPM330 Development Tool Setup 12
3.1 CMSIS-DAP and CooCox 12
3.2 Installation & Configuration of CooCox(CoIDE1.7.5)software 12
3.3 Installation & Configuration of GNU Tool Chain 17
Chapter 4 : Configuration of ColinkEx Debugger and Programming 21
4.1 Configuration of CMSIS-DAP Debugger and Programming 21
Chapter 5 : Schematic & Board Layout 29
5.1 Schematic & Board Layout 29
Chapter 6 : Change History 30
6.1 Change History 30
User Manual: Toshiba-TMPM330
Page | 3
Chapter 1: Introduction
The TMPM330 is an evaluation stamp board which is exploring the complete features of the new
ARM Cortex-M3 TMPM330FDFG microcontroller by Toshiba.Featuring a Toshiba TMPM330FDFG
microcontroller, the MCBTMPM330 Evaluation Board offers 512KB Flash, 32KB SRAM, a 10 channel
16-bit Timer, a 12 channel 10-bit ADC, real-time clock and watchdog, 3 UARTs, 3 I2C interfaces and
79 GPIO Pins.
TMPM330 Stamp Specifications
• Dimensions: 64.26 mm x 49.53 mm
• Two layer PCB (FR-4 material)
• USB mini connector ( as power source) with power indicator
• On-board linear regulators generate +3.3V/1A from power supply
• Extension headers for all Micro-controller pins
• One RS232 port connector
• 256Kb I2C based EEPROM
• 10 JTAG connector
• On-board two test LED's
• On-board user and reset switches
Chapter 2: CoFlash Installation & Flashing Binary codes
2.1:Installation & Configuration of CoFlash software
Follow the steps given below.
Step 1: Open CoFlash-1.4.6.exe setup downloaded from internet.
User Manual: Toshiba-TMPM330
Page | 4
Step 2: When you open CoFlash-1.4.6.exe setup you will the following window , click on 'Next'.
Step 3: Click on 'Next'.
Step 4: Click on 'Next'.
User Manual: Toshiba-TMPM330
Page | 5
Step 5: Click on 'Install'.
Step 6: Wait till Installation complete.
User Manual: Toshiba-TMPM330
Page | 6
Step 7: CoFlash-1.4.6.exe setup is completed, click on 'Finish' .
2.2: Flashing Binary Codes in CoFlash.
Follow the steps given below to check the binary codes. Step
1: Hardware Setup
Accessories Required:
1. Toshiba-TMPM330 stamp board.
2. CMSIS-DAP board.
3. 10 pin JTAG cable.
4. 2 USB mini cable.
5. 20 to 10 pin converter
6. 20 pin JTAG cable
User Manual: Toshiba-TMPM330
Page | 7
Step 2: Hardware Connection.
• Connect one end of 10-pin ribbon cable to ‘10-pin box header’ of the Toshiba-TMPM330
board and other end to the '10-Pin box header' of 20 to 10 pin converter board as shown in the
following image.
• Connect one end of ‘USB mini cable’ to CMSIS-DAP board and other end to computer, as
shown in the following image.
Step 3: Right click on 'CoFlash' and click on 'Open'.
2
3
4
User Manual: Toshiba-TMPM330
Page | 8
Step 4: You will get the following window when you open CoFlash. Now click on 'config' select
'CMSIS-DAP' Adapter and select 'TMPM330FDFG' in Toshiba as shown in the following image.
Step 5: Now click on 'Command' and browse the binary code.
User Manual: Toshiba-TMPM330
Page | 10
Step 8: Next check for 'Program Done' and click on 'close'.
Step 9: Verify the output as shown in image below.
User Manual: Toshiba-TMPM330
Page | 11
User Manual: Toshiba-TMPM330
Page | 12
Chapter 3 : TMPM330 Development Tool Setup
3.1 CMSIS-DAP and CooCox
NGX’s MCU evaluation platforms are not coupled tightly with any one particular combination of IDE
and debugger. The following sections will explain the setup for CooCox(CoIDE-1.7.5) and CMSIS-
DAP as the IDE and debugger respectively.
3.2 Installation & Configuration of CooCox(CoIDE-1.7.5) software
The Installation of CooCox (CoIDE-1.7.5) software is explained below:
Step 1: Open the CooCox(CoIDE-1.7.5) setup
User Manual: Toshiba-TMPM330
Page | 13
Step 2:
Step 3:
User Manual: Toshiba-TMPM330
Page | 14
Step 4:
User Manual: Toshiba-TMPM330
Page | 15
User Manual: Toshiba-TMPM330
Page | 16
Step 5: Click on Install.
Step 6: CooCox CoIDE(1.7.5) setup is completed, click on Finish .
User Manual: Toshiba-TMPM330
Page | 17
3.3 Installation & Configuration of GNU Tool Chain:
step 1: Open the GNU Tools setup.
Step 2: Select English language and click on OK as shown in below image.
User Manual: Toshiba-TMPM330
Page | 18
Step 3: Click on Yes.
Step 4: Click on Next.
User Manual: Toshiba-TMPM330
Page | 19
Step 5: Select ' I accept the terms of the license agreement' and click on 'Next'.
Step 6: Click on 'Next'.
User Manual: Toshiba-TMPM330
Page | 20
Step 7: Click on 'Next'.
Step 8: Wait till installation complete.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
