Bikehut 151657 Operating instructions

Brand: Bikehut

Model: 151657

Category: Bicycle accessories

Type: Operating instructions

3. Hold down the “RESET” button l till the LCD digit is blank, then release it. The

computer will RESET the DST, RTM, AVG, MAX.

CLOCK SETTING (Fig. 2)

1. Change the LCD display to CLK screen.

2. Press the SET button k to enter the clock adjusting screen to setting the clock.

3. A quick press of the MODE button j to select 12HR or 24HR.

4. Adjust the clock data as the data setting procedures.

RESET OPERATION (Fig. 4)

1. Hold down the RESET button l till the LCD digit is blanked, then release it. The

computer will reset AVG, DST, RTM and MAX data from stored values to zero.

2. It cannot reset ODO, CLK.

AUTOMATIC START/STOP

1. The computer will automatically begin counting data upon riding and stop counting data

when riding is stopped.

2. The flickering symbol " " indicates that the computer is at start status.

POWER AUTO OFF

To preserve battery, this computer will automatically switch off and just displays the CLK

data when it has not been used for about 15 minutes. The power will be turned on by

pressing the SET button k (Fig. g).

LOW BATTERY INDICATOR

1. The symbol " " will appear to indicate the battery is nearly exhausted.

2. Replace battery with a new one within a few days after the symbol was appeared,

otherwise the stored data may be lost when the battery voltage is too low.

BATTERY CHANGE (Fig. c)

1. All data will be cleared when battery is replaced.

2. This computer allows you to re-key in data of ODO which you have had rode

after replacing battery.

3. Keep record the ODO data before you remove the old battery.

4. Replace with a new CR2025 battery in the compartment on the back of the computer

with the positive (+) pole toward the battery cap.

5. Initiate the main unit again.

PRECAUTIONS

1. Do not leave the main unit exposed to direct sunlight when you don't ride the bike.

2. Do not try to disassemble the main unit or its accessories.

 Sensor:No Contact Magnetic Sensor.

 Battery Type:3.0V Battery X 1 (Typical No. CR2025)

 Battery Operating Life:CR2025 in Main Unit About one year

 (based on the average riding time of 1.5 hours per day)

 CR2032 in Speed Transmitter Around 24000km

 Dimensions/Weight:33 x 51 x 13.5mm / 22.4g

Wheel Circumference Setting:1mm - 3999mm (1mm increment)

 Operation Temperature:0°C ~ 50°C (32°F ~ 122°F)

 Storage Temperature:-10°C ~ 60°C (14°F ~ 140°F)

3. Check relative position between sensor, magnet and main unit periodically.

4. Don’t use thinner, alcohol or benzine to clean the main unit or its accessories when

they become dirty.

5. Remember to pay attention to the road while riding.

TROUBLE SHOOTING Check the following before taking unit in for repairs.

MAIN UNIT SETUP (Fig. 1)

When setting up the computer do not have

thecomputer on the handlebar bracket and ensure that the computer is only held by the sides.

INITIATE THE COMPUTER (ALL CLEAR)

1. A battery is already loaded in the main unit when purchased.

2. Hold down the SET button k and RESET button l simultaneously for more than 3

seconds to initiate the computer and clear all data. IMPORTANT: Be sure to initiate the

computer before it is be used, otherwise the computer may run errors.

3. The LCD segments will be tested automatically after the unit is initiated.

4. Press MODE button j to stop LCD test, then the flickering "KM/H".

UNIT SELECTION

Press MODE button j to choose KM/H or M/H. Then press the SET button k to store

selection.

WHEEL CIRCUMFERENCE

l Precise Measurement (Fig. a)

Roll the wheel until the valve stem is at its lowest point close to the ground, then mark this

first point on the ground. Get on the bicycle and have a helper push you until the valve

stem returns to its lowest point. Mark the second point on the ground. Measure the

distance between the marks. Enter this value to set the wheel circumference.

l Quick Table (Fig. b): Get a suitable circumference value from the table.

FUNCTIONS

(Fig. 3)

: Current Speed0.0–199.9Km/h (120.0 Mile/h), 0.1Km/h (Mile/h), +/- 1%

The current speed is always displayed on the upper set when riding. It displays current

speed up to 199.9 Km/h or 120.0 Mile/h (for wheel diameters over 24 inches).

CLK: 12HR or 24HR Clock 1H00M–12H59M or 0H00M–23H59M, 1 Minute, +/- 0.3%

It can display the current time either in 12HR or 24HR clock.

DST: Trip Distance 0.00–999.99Km (Miles), 0.01Km (Mile), +/- 0.01%

The DST function accumulates the distance data from the last RESET operation as long as

the bike is being ridden.

RTM: Riding Time 0M00S-59M59S, 1 Second, 0H00M-99H59M, 1 Minute, +/- 0.03%

1. The RTM totals the riding time from the last RESET operation.

2. It displays in 1 second increments when RTM is less than 1 hour and changes to 1 Minute

increments after 1 hour. It will restart from zero after 100 hours.

AVG: Average Speed 0.0–199.9Km/h (120.0Mile/h), 0.1Km/h (Mile/h), +/- 0.1%

1. It is calculated from the DST divided by the RTM. The average data counted is from the

last RESET to current point.

2. It will display "0.0" when RTM is less than 4 seconds.

3. It is updated about one second when RTM is over 4 seconds.

MAX: Maximum Speed

0.0–199.9Km/h (120.0Mile/h), 0.1Km/h (Mile/h), +/- 1%

It shows the highest speed from the last RESET operation.

TMP: Current Temperature °C / °F -10°C ~ 60°C (14°F ~ 140°F)

ODO: Odometer 0-99999Km (Miles), 1Km (Miles), ± 0.1%

The ODO accumulates total distance as long as the bicycle is running, the ODO data can be

cleared by the All Clear operation only.

: SCAN

1. Auto-Scanning Display Mode.

Press the MODE button j till the symbol is displayed. The computer will change the

display modes in a loop sequence automatically every 5 seconds.

2. Fixed Display Mode.

Press the MODE button j to turn off the symbol and select a desired display mode; the

computer will stop the auto-scanning display operation.

/ : Speed Pacer

It flashes the speed pacer arrow while the current speed is higher than the average

speed and the down arrow flickers conversely.

BUTTON AND OPERATIONS

After 15 minutes of inactivity the computer will lock the mode

button and will show a key on the screen (fig e), to unlock press button k.

MODE BUTTON j

Quickly press this button to move in a loop sequence from one function screen to another.

LOCK/SET BUTTON k

Hold down this button 2 seconds to get in or out the setting screens when you want to reset

to bike, or the current time of the CLK.

LIGHT/RESET BUTTON l

1. Light for 4 seconds after each press. (Fig. d)

2. The symbol " " will apper to indicate the EL back-light functuon is at working status.

English

1. Change one new battery.

2. Be sure that the positive pole of the

battery is facing the battery cap.

1. Refer to the setting procedure and

complete the adjustment.

2. Refer to Installations and re-adjust

position and gap correctly.

3. Refer to "Circumference Setting" and

enter correct value.

4. Refer to Installations and adjust distance or

angle between the main unit and the sensor.

5. Change one new battery.

6. Move the computer from this interference

source.

Refer to the "Main Unit Setup" and initiate

the computer again.

Place main unit in the shade to return to normal

state. There won't be negative effect for data.

Unit will return to normal state when the

temperature rises.

PROBLEM

CHECK YOUR COMPUTER REMEDY

No display

No current

speed or

incorrect

data

Irregular

display

LCD is black

Display is

slow

1. Is the battery dead?

2. Is the battery installation correct?

1. Is it at the MAIN UNIT SETUP or

other setting displays?

2. Is the relative position, gap between

sensor and magnet correct?

3. Is the circumference value input correct?

4. Is the sensing distance too long or the

installation angle of the sensor

incorrect?

5. Is the sensor battery nearly exhausted?

6. Is there any strong interference source

nearby?

Have you left the main unit exposed to

direct sunlight and no riding for a long time?

Is the temperature below 0°C (32°F)?

ALL CLEAR UNIT SELECTION CIRCUMFERENCE SETTING END SETTING General Mode Touch key Stuck (Mode key)

CLOCK SETTING ODO SETTING

RESET OPERATION (DST=0, RTM=0, AVG=0, MAX=0)

2s 2s

SEGMENTS

LCD

AUTO TEST

0~3 0~9 +1 0~9

0~5

jk kk l

j j j j j j j

ll l

j j

0~23

1~12

0~23 +1

0~9 +1

lj j j j

CLOCK DST RTM AVG MAX TMP ODO SCAN

4403000000_20090423_v1

MODE

OK!

j MODE

0 1 2 3 4

9 8 7 6 5

c. BATTERY CHANGE

Low battery

indicator

Data Setting Mode

k k

Tire Size

Circumference

Nunber

18 Inch 1436 mm

20 Inch 1596

22 Inch 1759

24x1.75 1888

24 Inch 1916

24x 1 3/8 1942

26x1.40 1995

26x1.50 2030

26x1.75 2045

26x1.95 2099

26x2.1 2133

700C TUBULAR 2117

700x20C 2092

700x23C 2112

700x25C 2124

700x28C 2136

700x32C 2155

700x35C 2164

700x38C 2174

27.5 Inch 2193

28 Inch (700B) 2234

28.6 Inch 2281

b. POPULAR TIRES

CIRCUMFERENCE

REFERENCE TABLE

0~9

0~3

WHEEL CIRCUMFERENCE

2nd 1st

LOCK/

SET

LIGHT/

RESET

Mount On Bracket

CR2025

15m

OFF

k k

ON OFF

f. g.

Power Off

Auto Key-lock

d. EL Back-light

e. KEY-LOCK

Mount On Bracket

Stop

Status

Riding

Status

15m

Release

Sensing zone

Key Stuck

OK!

O-ring

151657 Bikehut 11 Function Computer

Bikehut 151657 Operating instructions

Brand: Bikehut

Model: 151657

Category: Bicycle accessories

Type: Operating instructions

Download PDF

report

Bikehut 151657 Operating instructions

Bikehut 151657 Operating instructions

Other documents