Crux SWRTY-61C Radio Replacement User manual
- Category
- Motorcycle Accessories
- Type
- User manual
rev.042523
SWRTY-61C
Radio Replacement with Steering Wheel Control Retention for
Select Toyota Vehicles 2018-Up
1 of 3
RADIO REPLACEMENT
SWC RETENTION
+
R
INTERFACING SOLUTIONS
- Pre-programmed to retain factory Steering Wheel Controls.
- Retains factory back-up camera.
- Retains factory Auxiliary Audio Input.
- Includes antenna adapter.
PRODUCT FEATURES:
PARTS INCLUDED:
SWRTY-61C Module TY-61C Harness Speaker Harness SWC Cable USB Adapter
INSTALLATION DIAGRAM:
AFTERMARKET
RADIO
+12V Constant Yellow
+12V ACC Red
Ground
Reverse Gear Output
Vehicle Speed Sense Pink
Parking Brake Output Light Green
Amp Turn On Blue/White
Right Front (+) Gray
Right Front (-) Gray/Black
Left Front (+) White
Left Front (-) White/Black
Right Rear (+) Violet
Right Rear (-) Violet/Black
Left Rear (+) Green
Left Rear (-) Green/Black
Audio Input Red/White RCA
(Retains Factory AUX Input)
TO FACTORY
HARNESS
12-Pin Black
Connector
30 PIN
USB Retention Adaptor
(included in kit)
ANTENNA ADAPTOR
(Included in Kit)
Blue / Antenna Turn On
28 PIN
Yellow RCA
(Retains OE Camera)
Rear View Camera Signal Output
AFTERMARKET
RADIO SELECTOR
(See Chart)
TOYOTA
SWC SETTING
(OFF ON OFF ON)
ON RADIO VEHICLE
1 2 3 4 5 6 7 8
ON RADIO VEHICLE
1 2 3 4 5 6 7 8
4-Pin
Connector
Cap or insulate if
not being used
Kenwood/JVC (BLUE / YELLOW)
Insulate with tape
if not being used
3.5MM SWC CABLE
Plug in the 3.5MM SWC cable to the 4-pin port
on the module. See below for DIP switch settings.
To aftermarket
radio SWC wire
or 3.5mm port
To aftermarket radio
Remote Turn On wire
(Blue or Blue/White wire)
To aftermarket radio Aux Input
Purple/White or
Red/White
Ground
rev.042523
2 of 3
RADIO REPLACEMENT
SWC RETENTION
+
R
INTERFACING SOLUTIONS
SWRTY-61C
Radio Replacement with Steering Wheel Control Retention for
Select Toyota Vehicles 2018-Up
1. Connect the SWRTY-61C
harness. Refer to the diagram on
page 1 for wire color codes.
2. Remove the padded trim above the glove compartment.
3. Carefully pull out the trim under the
radio.
4. Remove the small trim next to the 5. Remove the AC control panel below
the radio.
6. Unplug the connector behind the AC
control panel.
7. Pull out the radio and unplug the
connectors.
8. Mate the factory radio connectors
to the SWRTY-61C T-harness. Test
rev.042523
3 of 3
RADIO REPLACEMENT
SWC RETENTION
+
R
INTERFACING SOLUTIONS
DIP SWITCH SETTINGS:
AFTERMARKET RADIO DIP SWITCH SETTINGS:
NOTE: Insulate the Blue/Yellow wire or 3.5mm plug if not being used.
TOYOTA STEERING WHEEL CONTROL DIP SWITCH SETTING:
DIP: 5 6 7 8
Toyota OFF ON OFF ON
SWC MODULE
ON RADIO VEHICLE
1 2 3 4 5 6 7 8
RADIO BRAND: DIP: 1 2 3 4
Atoto, Dual, Farenheit, Jensen, Pioneer
Power Acoustik, Soundstream
Alpine
Clarion
Kenwood
JVC
Boss, Old Sony
New Sony
OFF OFF ON ON
OFF OFF ON ON
OFF OFF ON ON
OFF OFF OFF OFF
OFF ON ON OFF
OFF ON ON ON
OFF ON OFF ON
OFF ON OFF OFF
OFF OFF ON OFF
SWC MODULE
ON RADIO VEHICLE
1 2 3 4 5 6 7 8
NOTE:
check the aftermarket radio’s manual to see if the SWC buttons need to be programmed.
3.5MM SWC CABLE
Plug in the 3.5MM to 4-Pin SWC cable to the SWC module.
VEHICLE APPLICATIONS:
SWRTY-61C
Radio Replacement with Steering Wheel Control Retention for
Select Toyota Vehicles 2018-Up
RED to SWC Key 1
WHITE to SWC Key 2
SHIELD to SWC Ground
SWC wires as follows:
Note that there are some radios that only have SWC1 and SWC2, in this case “shield” does not need to be connected.
Toyota
2020-Up
2019-Up
2018-Up
2019-Up
2018-Up
2020-Up
4Runner
Avalon
Camry
CH-R
Corolla
Highlander
2019-Up
2020-Up
2018-Up
2020-Up
2020-Up
RAV4
Sequoia
Sienna
Tacoma
Tundra
-
1
-
2
-
3
Crux SWRTY-61C Radio Replacement User manual
- Category
- Motorcycle Accessories
- Type
- User manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI