Moffat E33D5 Operating instructions

Brand: Moffat

Model: E33D5

Category: Microwaves

Type: Operating instructions

This manual is also suitable for

246963-1

Installation and Operation Manual

E 3 3 D 5 - 3 P h a s e M o d e l

 2 Speed Fan

 Moisture Mode

 Multi-Stage Cooking

 Optional Core Temp Probe

The reproduction or copying of any part of this manual by any means whatsoever is strictly forbidden unless authorized previously in writing

by the manufacturer.

In line with policy to continually develop and improve its products, Moffat Ltd. reserves the right to change the specifications and design

without prior notice.

Moffat Limited

Rolleston 7675

New Zealand

AUSTRALIA

Moffat Pty Limited

Web: www.moffat.com.au

E.Mail: vsales@moffat.com.au

Main Office: (tel) +61 (03) 9518 3888

(fax) +61 (03) 9518 3838

Service: (tel): 1800 622 216

Spares: (tel): 1800 337 963

Customer Service: (tel): 1800 335 315

(fax): 1800 350 281

CANADA

Serve Canada

Web: www.servecanada.com

E.Mail: info@servecanada.com

Sales: (tel): 800 551 8795 (Toll Free)

Service: (tel): 800 263 1455 (Toll Free)

NEW ZEALAND

Moffat Limited

Web: www.moffat.co.nz

E.Mail: sales@moffat.co.nz

Main Office: (tel): 0800 663328

UNITED KINGDOM

Blue Seal

Web: www.blue-seal.co.uk

E.Mail: sales@blue-seal.co.uk

Sales: (tel): +44 121 327 5575

(fax): +44 121 327 9711

Spares: (tel): +44 121 322 6640

(fax): +44 121 327 9201

Service: (tel): +44 121 322 6644

(fax): +44 121 327 6257

UNITED STATES

Moffat

Web: www.moffat.com

Sales: (tel): 1-800 551 8795 (Toll Free)

(tel): 336 661 1556

(fax): 336 661 9546

Service: (tel): 866 673 7937 (Toll Free)

REST OF WORLD

Moffat Limited

Web: www.moffat.co.nz

E.Mail: e[email protected]

Contents List

Safety Information

Installation Requirements

Unpacking

Location

Clearances

Stand Mounted Ovens

Electrical Connection

Water Connection

Recommended Water Specifications

Positioning and Levelling of Oven

Initial Start-Up

Commissioning

Operation Guide

Cooking in Manual Mode

Cooking in Manual Mode using Core Temp Probe

Cooking in Program Mode

Programs

Parameters

Programs Revision Numbering

Files

Changing Operator Settings

Operator Settings

Cleaning Guidelines

Oven Cleaning

Periodic Maintenance

Introduction

Before using your new oven, please read this instruction manual

carefully, pay particular attention to any information labelled

‘WARNING’, ‘CAUTION’, ‘IMPORTANT’ or ‘NOTE’ in this manual.

Indicates a hazardous situation

which, if not avoided, will result in

death or serious injury.

Indicates a hazardous situation

which, if not avoided, will result in

minor or moderate injury.

If you are unsure of any aspect of the installation, instructions or

performance of your oven, contact your TURBOFAN dealer promptly.

In many cases a phone call could answer your question.

Should you contact your TURBOFAN dealer on any matter concerning

this oven, please have the information provided opposite, readily

available.

This manual must be kept by the owner for future reference.

A record of

Date of Purchase,

Date of Installation

and

Serial

Number of the oven

should be recorded in the area provided

below.

The serial number of this oven can be found on the

Technical Data Plate located on the front right hand side

panel, see diagram in ‘Installation Section’.

For your safety, please pay attention to the following symbols

marked on the appliance.

- Risk of electric shock.

No user serviceable parts inside.

Qualified service person access only.

Disconnect from power before servicing.

Specifications

E33D5

Oven Power Ratings 380V, 50Hz, 3P+N+E, 6.0kW.

L1 : 0.7A, L2 : 13.2A, L3 : 13.2A

Oven Tray Details Tray Capacity 5 Shelf, 1/1 GN Pan.

Tray Spacing 85mm / 31/3”.

Water Connection Max Water Pressure 80psi / 550kPa.

Connection Size 3/4” BSP.

NOTE: If the Moisture Mode cooking option is not required, the oven does not need to

be connected to a water supply.

Installation

1. Remove all packaging and transit protection including all

protective plastic coating from the exterior stainless steel

panels.

2. Check the oven and supplied parts for damage. Report any

damage immediately to the carrier and distributor.

3. Check that the following parts have been supplied with your

oven:-

4 x Leg Adjustable.

4. Report any deficiencies to the distributor who supplied your

oven.

5. Securely fit the 4 legs supplied with the oven.

6. Check that the available electrical supply is correct to that

shown on the Technical Data Plate located on the front right

hand side panel.

 Also refer to ‘Specifications’ section, ‘Oven

Specifications Table’ on previous page.

1. Position the oven in its approximate working position.

2. The unit should be positioned so that the control panel

and oven shelves are easily reachable for loading and

unloading.

To ensure correct ventilation for the motor and controls, the

following minimum installation clearances are to be adhered to:-

Top 200mm / 8”.

Rear 50mm / 2”.

Left-hand side 50mm / 2”.

Right-hand side 75mm / 3”.

Clearance From Source of Heat.

A minimum distance of 300mm (12”) from the appliance

sides is required.

NOTE: Fixed installations require at least 500mm (20”)

clearance for service access.

For stand mounted ovens, the oven feet are used to level the oven

on the stand. Refer to the instructions supplied with separately

ordered stands for mounting details.

The vent located on the top of the oven must NOT be

obstructed.

 Installation shall comply with local electrical, health and safety requirements.

 It is most important that this oven is installed correctly and that oven operation is correct before use.

 If you have any questions regarding the proper installation and / or operation of this oven, please contact your local

Turbofan distributor.

Technical Data Plate - Location

Oven Vent Location

Installation

RCD (Residual Current Device) / GFCI (Ground-Fault Circuit-

Interrupter) protection of the power supply to this appliance is

recommended.

Each oven should be connected to an adequately protected power

supply with an appropriate three wire power cord.

An isolation switch must be mounted adjacent to, but not behind

the oven and must be readily accessible to the operator. This

switch must be clearly marked and readily accessible in case of fire.

Check the electricity supply is correct to as shown on the Technical

Data Plate on the front right hand corner of the oven side panel.

NOTE: All electrical connections must only be carried out by

a suitably qualified person.

1. Remove oven right hand side panel.

2. Bring the supply cable up through the grommet at the back of

oven and through the compression gland on the electrical

switchgear panel.

3. Connect the mains supply to the appropriately marked

terminals on the terminal block.

NOTE: If the Moisture Mode cooking option is not required,

the oven does not need to be connected to a water

supply.

1. Tighten the 2 screws securing the

water connection to the rear of the

oven. (These have purposely been

left loose to prevent damage to the

water connection during transit).

2. Connect a cold water supply to the

water inlet (R ¾” Connector) on the

oven.

NOTE:

For USA / Canada / Mexico, the supplied ¾” GHT Brass

Adaptor and Washer should be used to connect a water

supply to the oven water inlet.

- Max Inlet Pressure 80psi / 550kPa.

3. Turn ‘On’ the water supply and check for leaks.

In order to prevent corrosion or scaling in the oven and water

system due to supplying water that is either too soft or too hard,

the following recommendations should be used as a guideline.

Hardness: Between 60 and 90ppm.

PH: Greater than 7.5.

Chlorides: Less than 30ppm.

This oven must be earthed / grounded.

1. Correctly locate the oven into its final operating position and

using a spirit level, adjust the oven feet so that the oven is level

and at the correct height.

Before using the new oven;

1. When using the oven for the first time, operate oven for about

1 hour at 200°C / 400°F to remove any fumes or odours which

may be present.

2. Please refer to the Operation Section of this manual for details

on how to correctly operate and shutdown the oven.

Before leaving the new installation;

1. Check the oven functions in accordance with the operating

instructions specified in the ‘Operation’ section of this manual.

2. Ensure that the operator has been instructed in the areas of

correct operation and shutdown procedure for the appliance.

NOTE: If it is not possible to get appliance to operate

correctly, turn ‘Off’ power at the mains supply and

contact supplier of this appliance.

Tighten Screws.

Operation

 This oven is intended for use in a commercial kitchen and must only be put to the use for which it was intended, i.e. cooking food

product. To use this oven correctly please read the following sections carefully:-

Temperature Display -

Shows pre-set chamber temperature.

When used with the ‘Temp’ key,

display shows actual oven temperature for 5

seconds.

Shows cooking programs and error codes.

‘Steam’ Key and LED -

Used to set moisture level or to

provide a manual injection of moisture

when in Manual Moisture Mode.

LED is ‘On’ when automatic moisture injection is

set or when moisture is manually injected.

Temperature Adjustment Control

Time Display -

Shows cook time in full minutes only

from 180 - 10, and in minutes and seconds for

the final 10 minutes.

NOTE:

In Core Temp Mode, time display alternates

between ‘CP’ and set core probe

temperature.

‘On-Off/Light’ Key and LED -

A dual-function key:

Press ‘On-Off/Light’ key once to turn

the oven ‘On’

When oven is turned ‘On’, press ‘On-Off/Light’

key to switch oven light ‘On-Off’.

Press and hold ‘On-Off/Light’ key for 1.5 seconds

to turn the oven ‘Off’.

Time Adjustment Control

NOTE: In Core Temp Mode, ‘Timer’ knob is

used to set core probe temperature.

‘Program’ Key and LED -

Used to select cooking programs, and

to set program parameters.

‘Temp’ Key and LED -

Displays actual oven temperature for 5

seconds on Temperature Display. LED

‘On’ when heating element is on

(heating indicator).

LED flashes when Upper Display is showing

actual temperature.

NOTE:

In Core Temp Mode, this key is used to

display Actual Oven Temperature (Upper

Display) and actual Core Probe Temperature

(Lower Display).

‘Fan Lo’ Speed Key and LED -

Switches oven fan from high to low

speed. LED is ‘On’ when fan is in Low

Speed Mode. When LED is ‘Off’, fan is

in High Speed Mode.

‘Timer-Start/Stop’ Key & LED -

The ‘Timer-Start/Stop’ key is used to

control the following functions:-

 Cancelling Alarm (All Modes).

 Starting Core Temp Mode (Core Temp

Mode).

 Starting Timer (Manual Mode).

 Re-Setting Timer (Manual Mode).

 Starting Program (Program Mode).

 Cancelling and Re-Setting Program

(Program Mode).

Core Probe Connection Point.

Operation

There are 6 levels of pre-set moisture injection.

Each level defines the number of moisture injection pulses per

moisture cycle during oven operation.

H-0 Manual Moisture Mode. Automatic Moisture Injection is ‘Off’.

Pressing ‘Steam’ key in this mode will inject 1 shot of steam

into the oven, ie, no steam injection without user input.

H-1 Level 1. - Minimum automatic moisture injection setting. One

moisture pulse per moisture cycle.

H-2 Level 2.

H-3 Level 3.

H-4 Level 4.

H-5 Level 5. - Maximum automatic moisture injection setting.

Five moisture pulses per moisture cycle.

Selecting Moisture Mode

Press ‘Steam’ key to activate Moisture Mode. ‘Steam’ key

LED will illuminate when Moisture Mode is ‘On’. Moisture

Mode will operate at the preset level during the cooking

cycle.

 When Moisture Mode H-0 is selected, a shot of steam is

available whenever the oven is running, by pressing the

‘Steam’ key.

 When Moisture Mode H-1 to H-5 are selected, these

moisture modes will only operate when a program is run-

ning, Core Temp Probe Mode has been selected or when a

timer is running in Manual Mode.

 When setting Moisture level, consider the Oven Set

Temperature. If set BELOW 100°C (212°F), water may pool

in oven as temperature will be too low to create steam.

Changing Moisture Mode Level

Press and hold the ‘Steam’ Key until the ‘H-X’ level is

displayed and flashing in the upper display.

Rotate the ‘Temp’ Knob -/+ to select Moisture Mode level

required.

Press the ‘Steam’ key to confirm setting.

The ‘Moisture’ Mode level can be changed at anytime during

operation by following the setting method as described above.

An Optional Core Temp Probe Kit #236060 is available for

this oven.

This allows use of the Core Probe Cooking feature of this oven.

When the core probe is fitted to the connection point on control

panel side, the timer function and display becomes the core temp

probe temperature setting and display. Cooking completion is then

determined by the core temp probe reaching the set core probe

temperature.

To enable Core Probe Cooking Mode plug in the Core Probe.

The Timer Display will then change to 'CP' (Core Probe).

The Timer Knob function will then be for Core Temp setting.

To disable Core Probe Cooking Mode, unplug the Core Probe.

The Timer Display and Knob will return to time function.

In Manual mode the ovens settings are.

- Temperature - 50-250C / 150-550F.

- Timer setting - 0-180min or Infinite.

- Fan Speed setting - Hi / Lo.

- Moisture Mode settings - Off / On-Level.

- Oven lights - Off / On.

An Optional Core Probe can also be used in Manual Mode.

In Program Mode 20 Programs are able to be used.

In each program the following settings are possible.

- Temperature - 50-250C / 150-550F.

- Time - 0-180min or Infinite.

- Fan Speed - Hi/ Lo.

- Moisture Mode - Off / On-level.

3 cooking stages can also be set in each of the 20 programs.

- All settings can be changed between cooking stages.

- At completion of each stage an end of stage alarm can also

be set.

Optional Core Probe can also be used in Program Mode.

Changing between Manual to Program Modes

Press ‘Program’ key to select Program Mode. The LED

will illuminate showing Program Mode now set.

Press ‘Program’ Key to return to Manual mode.

This oven features a 2 speed fan.

Hi Speed - This is the default operating speed.

- Hi Fan should be used for most applications.

- Hi Fan provides the fastest cooking time and evenness

throughout oven.

Lo Speed - This is the optional setting.

- Lo Fan speed is selected using the Fan Lo key.

- Lo Fan provides slower cooking with less fan affect on

the product.

- Lo Fan should be used on delicate products such as

cake and muffin.

On start-up, the oven will always default to normal Hi speed fan.

In Manual Mode, fan speed can be changed at any time during use.

In Program Mode, fan speed can be pre-set and each cooking stage

can have a different fan speed.

Changing the Fan Speed

Press ‘FAN LO’ key to change to Lo Fan speed. LED will

illuminate showing Lo Fan speed is now set.

Press ‘FAN LO’ key to change back to Hi Speed fan.

Operation

On oven start-up the controller defaults to the following settings:-

Oven Temperature is set to 150°C (325°F). Refer ‘Controller - Operator Settings’ section to change this start-up temperature.

Oven Timer is not set, display shows ‘ - - -’.

Moisture Setting is setting to Manual Injection.

Fan Speed is set to Hi Speed.

1. SET OVEN TEMPERATURE.

Rotate ‘Temp’ knob to select temperature required.

+ to increase the temperature (Max. 260°C / 500°F).

- to decrease the temperature (Min. 60°C / 140°F).

The oven will commence heating to the displayed set temperature.

NOTE: The oven can be used without using the timer.

2. SET TIMER.

Rotate ‘Timer’ knob to select time required.

+ to increase the time (Max. 180 minutes).

- to decrease the time (Min. 1 minute).

NOTE: Timer can be set to ‘Infinity’ . If timer is set to ‘Infinity’, timer will

count elapsed time to a max of 999 minutes and elapsed time will be

shown on the Lower Display.

3. SET MOISTURE MODE.

Press and hold ‘Steam’ key for 3 seconds.

Rotate ‘Temp’ knob to select desired moisture level (H-0 to H-5).

Press ‘Steam’ key to confirm settings.

NOTE: Refer to ‘Moisture Mode Settings’ at start of this section for additional

explanation of moisture level adjustments.

4. SET FAN SPEED.

Press ‘Fan Lo’ key, to change fan speed. ‘Fan Lo’ LED will illuminate when

fan low speed is selected.

5. STARTING TIMER.

Press ‘Timer-Start/Stop’ key to start timer operation. LED will illuminate to indicate the

timer is running.

Press and hold ‘Timer-Start/Stop’ key for 3 seconds to cancel timer.

6. CANCELLING ‘TIME UP’ ALARM (COOKING TIME COMPLETED).

When the set Cooking Time is completed, alarm will sound and Lower Display flashes.

- Press ‘Timer-Start/Stop’ key to cancel alarm, oven will continue cooking at Oven Set Temperature. Display will revert to Set

Temperature and Time.

- Alternatively, open oven door to cancel alarm and turn ‘Off’ fan and heating. Close oven door to resume cooking at Oven

Set Temperature. Display will revert to Set Temperature and Time.

NOTE: Any of the above settings can be adjusted during the cooking operation by using the above controls and keys.

 Viewing Actual Oven Temperature. Press ‘Temp’ key during cooking, Oven Actual Temperature will display on Upper

Display for 5 seconds and then will revert to displaying Oven Set Temperature.

‘Steam’ LED will

illuminate when

automated

Moisture Mode is

set (H-1-H-5) or

during each

moisture

injection in H-0.

‘Fan Lo’ LED is

‘On’ when oven

fan is operating

at low speed.

‘Timer-Start/

Stop’ LED is

steady ‘On’ when

Timer is running.

‘Temp’ LED will

remain ‘On’ until

oven reaches Set

Temperature.

Operation

On oven start-up the controller defaults to the following settings:-

Oven Temperature is set to 150°C (325°F). Refer ‘Controller - Operator Settings’ section to change this start-up temperature.

Oven Timer is not set, display shows ‘ - - -’.

Moisture Setting is setting to Manual Injection.

Fan Speed is set to Hi Speed.

1. CONNECT CORE TEMP PROBE.

Connect Core Temp Probe to connector on lower right side of

control panel, will be displayed on Lower Display.

2. SET OVEN TEMPERATURE.

Rotate ‘Temp’ knob to select temperature required.

+ to increase the temperature (Max. 260°C / 500°F).

- to decrease the temperature (Min. 60°C / 140°F).

The oven will commence heating to the displayed set temperature.

3. SET CORE PROBE TEMPERATURE.

Rotate Timer Knob to set the desired core probe temperature.

+ to increase temperature (Max. 90°C / 194°F).

- to decrease temperature (Min. 50°C / 122°F).

Once Core Probe Set Temperature is set, Lower Display will alternately flash

between and Core Probe Set Temperature.

‘Timer-Start/Stop’ LED is ‘Off’, indicating that cooking has not yet started.

4. SET MOISTURE MODE.

Press and hold ‘Steam’ key for 3 seconds.

Rotate ‘Temp’ knob to select desired moisture level (H-0 to H-5).

Press ‘Steam’ key to confirm settings.

NOTE: Refer to ‘Moisture Mode Settings’ at start of this section for additional

explanation of moisture level adjustments.

5. SET FAN SPEED.

Press ‘Fan Lo’ key, to change fan speed. ‘Fan Lo’ LED will illuminate when fan

low speed is selected.

6. START CORE TEMP MODE COOKING.

Press ‘Timer-Start/Stop’ key to start Core Temp Mode cooking. ‘Timer-Start/Stop’ LED is ‘On’ during Core Temp Mode

cooking. Lower Display will alternately flash between and Core Probe Set Temperature during cooking.

7. CANCELLING CORE TEMP ALARM (CORE TEMP SETTING REACHED - COOKING COMPLETE).

When Core Probe Set Temperature is reached, an alarm will sound and the Lower Display will flash.

- Press ‘Timer-Start/Stop’ key to cancel alarm, oven will continue cooking at Oven Set Temperature. Display will show Oven

Set Temperature and Core Probe Set Temperature.

- Alternatively, open oven door to cancel alarm and turn ‘Off’ fan and heating. Close oven door to resume cooking at Oven

Set Temperature. The display will revert to the Oven and Core Probe Set Temperatures.

NOTE: Any of the above settings can be adjusted during cooking operation by using the above controls and keys.

 Viewing Actual Oven and Core Temperatures. During cooking, press ‘Temp’ key to check Oven Actual

Temperature (Upper Display) and Core Probe Actual Temperature (Lower Display). Actual temperatures will display for 5

seconds before display reverts to show Oven Set Temperature (Upper Display) and Core Probe Set Temp (Lower Display).

 Exiting Core Temp Cooking Mode. Disconnect Core Probe from connector on low er right side of control

panel. Lower Display and ‘Timer’ knob will revert to normal Timer Mode operation.

In Core Temp

Mode, the Lower

Display will

alternate

between ‘CP’ and

the Core Probe

Set Temperature.

‘Timer-Start/

Stop’ LED is ‘On’

when Cook Mode

in Progress.

In Core Temp

Mode, pressing

‘Temp’ key will

also display Core

Probe Actual

Temperature on

Lower Display.

In Core Temp

Mode, the ‘Timer’

knob is used to

set Core Probe

Temperature.

Operation

The oven can be pre-programmed with up to 20 Programs; each program can contain a maximum of 3 stages. When you receive your oven,

the controller is not pre-programmed.

1. SELECTING A PROGRAM.

Press ‘Program’ key.

Upper Display will show program number selected.

+ to scroll forward through programs.

- to scroll backward through programs.

Lower Display will show , oven is ‘Pre-Heating’.

Program cannot be started until pre-heating is completed.

2. OVEN READY.

Lower Display will show when oven is up to pre-heat temperature and an

alarm will sound.

Load product into oven.

3. CONNECT CORE TEMP PROBE (IF REQUIRED).

Connect Core Temp Probe to connector on lower right side of control panel,

will be displayed on Lower Display.

NOTE: A Core Temp Probe can be used as part of a multi-stage cooking program.

If a program reaches a Stage that requires a Core Temp Probe and no Core

Temp Probe is connected, an error alarm will sound and ‘CP’ will flash on

Lower Display. The program is automatically paused until the Core Temp

Probe is connected. Once the probe is connected to the control panel and

inserted into the food product, press the ‘Timer-Start/Stop’ key to resume

the program.

4. START PROGRAM.

Press ‘Timer-Start/Stop’ key to start cooking program.

 Pressing and holding ‘Timer-Start/Stop’ key for 3 seconds will cancel the program and return to the Preset Program.

During Program Operation the Upper and Lower Displays will show the following:-

 Upper Display shows Program Number, e.g.

 Lower Display will show either,

- Total Time Remaining in Program.

- Total Elapsed Time of Program (if any Program Stages are set to CP or InF).

- Alternate between ‘CP’ and Core Probe Set Temp (if presently in a Core Probe Stage).

5. CANCELLING PROGRAM ‘TIME UP’ ALARM (COOKING TIME COMPLETED).

When program is completed, the alarm will sound.

 To cancel alarm, press ‘Timer-Start/Stop’, oven will continue to cook at Oven Set Temperature. Display will revert to

Program Number (Upper Display) and Total Program Time (Lower Display).

 Alternatively, open oven door to cancel alarm and turn ‘Off’ fan and heating. Close oven door to resume cooking at Oven

Set Temperature. Display will revert to Program Number (Upper Display) and Total Program Time remaining (Lower

Display).

‘Program’ LED is

‘On’ when Oven

operating in

Programs Mode.

Operation

NOTE: Adjustments made during cooking will not be saved to the program.

A. VIEWING STAGE NUMBER AND STAGE TIME REMAINING.

To view the Program and Stage numbers on the Upper Display, e.g. 3.1 = Program 3, Stage 1, and the Total Time Remaining in Stage

remaining on the Lower Display:

- Press ‘P’ key during Program Cooking.

- Turn Timer knob in either direction.

 Upper Display will show Program and Stage, e.g.

 Lower Display will show either,

- Total Time Remaining in Stage.

- Total Elapsed Time of Stage (if Stage is set to ‘InF’).

- Core Probe Set Temp (if Stage is set to ‘CP’).

- Alternate between ‘CP’ and Core Probe Set Temp (if presently in a Core Probe Stage).

Display will revert back to Overall Display after 5 seconds.

B. USING ‘TEMP’ KNOB DURING PROGRAM COOKING.

 VIEWING SET TEMPERATURE

Turn ‘Temp’ knob (in either direction) to display Set Temperature of Current

Stage on Upper Display. Display will revert back to Overall Display after a

5-second delay.

 ADJUSTING SET TEMPERATURE

Hold ‘Temp’ knob in either direction for 3 seconds will enter ‘Temp Edit Mode’

where ‘Temp’ knob can be used to temporarily adjust temperature for the current

stage. Controller will update the Temperature and exit ‘Temp Edit Mode’ after a

5-second delay.

C. USING ‘TIMER’ KNOB DURING PROGRAM COOKING.

 VIEWING STAGE NUMBER AND REMAINING TIME

Turn ‘Timer’ knob (in either direction) to switch the display from Overall

(Program, Total Time remaining) to Current Stage-in-Progress (Stage, Stage

Time Remaining). Display will revert to Overall display after a 5-second delay.

 ADJUSTING REMAINING TIME / ADJUSTING CORE PROBE SET TEMP

Hold the ‘Timer’ knob in either direction for 3 seconds to enter ‘Timer Edit Mode’

where ‘Timer’ knob can be used for temporary adjustment of either:

- Core Probe Set Temperature.

- Stage Time remaining.

The controller will update the value and exit ‘Timer Edit Mode’ after a 5-second delay.

Time remaining can be adjusted between 0-180 minutes, but cannot be set to ‘InF’ or

‘CP’.

Core Probe Set Temp can be set between 50-90°C (122-194°F).

NOTE: Any changes will only apply to the current stage. Any following stages will

revert to the programmed settings.

Here the Oven Set Temperature has been

increased from 150 to 175°C (325 to 350°F).

Here Core Probe Temperature has been

increased from 54 to 75°C (129 - 167°F).

Operation

D. CHANGING THE MOISTURE SETTING.

Press and hold ‘Steam’ key for 3 seconds.

Rotate ‘Temp’ knob to select desired moisture level (H-0 to H-5).

Press ‘Steam’ key to confirm settings.

NOTE: Refer to ‘Moisture Mode Settings’ at start of this section for additional explanation of moisture level adjustments.

E. CHANGING FAN SPEED.

The pre-set fan speed can be changed by pressing ‘Fan Lo’ key. ‘Fan Lo’ indicator will illuminate when fan low speed is

selected.

F. VIEWING ACTUAL OVEN TEMPERATURE / ACTUAL CORE PROBE TEMPERATURE.

Press ‘Temp’ key during cooking. Oven Set Temperature will display on Upper Display for 2 seconds, then Actual Temperature

will display on Upper Display for 2 seconds. At the same time, Actual Core Probe temperature will display on Lower Display

for 4 seconds. After 4 seconds, controller will revert to displaying the program number.

G. ADDING MORE TIME TO A STAGE WHEN THE END OF STAGE ALARM IS SOUNDING.

At the end of a stage, provided that ‘ALr’=On, an end of stage alarm will sound for 1 minute before automatically progressing on to the

next stage of the program. While alarm is sounding, additional cooking time can be added to the stage that has just finished.

Rotate and hold ‘Timer’ knob for 3 seconds to enter Timer Edit Mode and add time to the stage.

When the length of time required has been added, either;

- Press ‘Timer-Start/Stop’ key to resume the stage,

- Wait for the auto-resume feature to progress the oven on to the next stage, 1 minute after alarm initially sounded.

When the additional time has run out, the end of stage alarm will sound for a second time. Either press ‘Timer-Start/Stop’ key

to progress on to the next stage, or let the program automatically progress on to the next stage after 1 minute of inactivity.

H. TURNING THE LIGHTS ‘ON/OFF’.

Whenever the oven is ‘On’, the ‘On/Off-Light’ key is used to turn the oven lights ‘On/Off’. Press ‘On-Off/Light’ key to switch

oven light ‘On-Off’.

To extend bulb life, an auto time-out can be pre-set to switch oven lights ‘Off’ after a set length of time. The factory default

for time-out is ‘Off’ (‘0’, ie lights remain ‘On’ until light key is pressed again). This time-out can be activated by setting the

‘Controller - Operator Settings’, L-0 from 1-60 minutes.

NOTE: Any changes will only apply to the current stage. Following stages will revert to the programmed settings.

Programming

The oven can be pre-programmed with up to 20 Programs; each program can contain a maximum of 3 stages. When you receive your oven,

the controller is not pre-programmed. To set programs, carry out the following for each program required:

1. SELECT PROGRAMS MODE.

Press ‘Program’ key to enter Programs Mode.

‘Program’ LED will illuminate.

2. SELECT PROGRAM REQUIRED (P01 - P20).

Rotate ‘Temp’ knob to the program required.

Upper Display will show program selected.

3. ENTER PROGRAMMING MODE.

Press and hold ‘Program’ key until a beep is heard, indicating entry into

Programming Mode. Upper Display shows program and stage numbers

= Program 3, Stage 1.

‘Program’ LED will flash whilst in Programming Mode.

4. SELECT STAGE TO PROGRAM.

NOTE: If Multi-Stage Cooking is disabled, (Parameter ’StG’ - refer to section

‘Controller Operator Settings’) skip to Step 6 to continue

programming otherwise continue as below and overleaf.

All active stages and the first inactive stage are visible and can be accessed by

rotating the ‘Temp’ knob to scroll through the stages. When editing a program for

the first time, only the first stage will be visible and it will be ‘Off’ by default.

Setting parameters for a stage changes its state from ‘Off’ to ‘On’ (activates the

stage).

 To Turn a Stage ‘On’.

Either - Rotate ‘Timer’ knob clockwise to

select ‘On’.

Or - Press ‘P’ key and program stage settings.

(Setting parameters for a stage automatically

changes its state to ‘On’).

 To Turn a Stage ‘Off’.

Rotate ‘Timer’ knob anti-clockwise to select ‘Off’.

NOTE: Only the last active (‘On’) stage can

be turned ‘Off’.

Rotate ‘Temp’ knob:-

‘+’ to advance one stage.

‘-’ to go to the previous stage.

‘Program’ LED is ‘On’

when Oven is

operating in

Programs Mode.

In Program Mode,

‘Temp Knob’ is

used to select:-

Program.

Stage.

And to set:-

Cook Temperature.

Moisture Level.

Fan Speed Option.

In Program Mode,

‘Timer’ Knob is

used to select:-

Core Probe.

And to set:-

Program Time.

Core Probe

Temperature.

Program 3, Stage 1.

STATE: ON.

Program 3, Stage 2.

STATE: ON.

Program 3, Stage 3.

STATE: OFF (ie; Inactive).

Programming

5. CONFIRM STAGE TO EDIT.

Press ‘Program’ key to begin editing a program and stage displayed on the Upper Display.

6. SET OVEN TEMPERATURE.

*Upper Display flashing*

Rotate ‘Temp’ knob to select temperature required.

+ to increase the temperature (Max. 260°C / 500°F).

- to decrease the temperature (Min. 60°C / 140°F).

Press ‘P’ key to confirm temperature setting. Controller will step to Cook Time / Core Temp Probe setting.

7. SET COOK TIME / CORE TEMP PROBE.

*Lower Display flashing*

The ‘Timer’ knob can be used to select Core Temp Probe or a Cook Time option.

 By setting a Cook Time, the stage w ill be governed by Oven Tem perature, Timer, Moisture setting and Fan Speed.

Rotate ‘Timer’ knob to select time required.

+ to increase Cook Time (Max. 180 minutes).

- to decrease Cook Time (Min. 1 minute).

Press ‘P’ key to confirm Timer setting and advance to setting Moisture setting.

 By setting Core Temp Probe (CP), the stage will run at a set Oven Temperature, Moisture Mode and Fan Speed until the actual

core temperature reaches the pre-set core probe temperature value. Refer to the ‘Cooking in Manual Mode with Core Probe’

Section for instructions on cooking with the Core Probe fitted. Turn and hold timer knob until lower display shows ‘CP’.

Controller will step to setting Core Probe Temperature. Core Probe Temperature value is displayed on Lower Display.

Rotate ‘Timer’ knob to select temperature required.

‘+’ to increase Core Probe Temperature (Max 90°C / 194°F).

‘-’ to decrease Core Probe Temperature. (Min 50°C / 122°F).

Press ‘P’ key to confirm Core Probe Temp Setting. Controller will step to Moisture setting.

 By setting Infinite Time setting (‘InF’), Oven counts time upwards up to a limit of 999 minutes. The Infinite (‘InF’) timer

option is only available as an option when setting the last stage of a program. If the ‘InF’ timer option is programmed, no stages

after the ‘InF’ stage will be available / visible. Turn ‘Off’ all stages that come after a given stage in order to set an ‘InF’ timer for

that stage.

Press ‘P’ key to confirm infinite time ‘InF’ setting and advance to setting Moisture setting.

= Stage has been set to ‘OFF’.

= Infinity Time Setting.

= Core Temp Probe (optional extra).

Time = From 1 minute to 180 minutes.

Turn and Release Timer Knob to change

selection.

Hold Knob to Fast Forward Fast Reverse.

   

1 Min 180 Mins

Programming

8. SET MOISTURE OPTION (H-0 - H-5).

*Upper Display flashing*

Rotate ‘Temp’ knob to select Moisture setting required.

‘+’ to increase moisture setting.

‘-’ to decrease moisture setting.

(Refer to Operation section, ‘Moisture Mode Settings’, for additional explanation of moisture level adjustment).

Press ‘P’ key to confirm Moisture setting. Controller will step to Fan Speed setting.

9. SET FAN SPEED (LO - HI).

Upper Display shows

*Lower Display Flashing with current Fan setting*

Rotate ‘Timer’ knob to select desired fan option, shown on Lower Display.

Press ‘P’ key to confirm fan speed setting. Controller will step to Alarm setting for End of Stage.

NOTE: If Multi-Stage Cooking is disabled, (Operator setting ’StG’ - set to ‘no’), the controller will exit the Programming

Mode after the ‘P’ key is pressed to confirm fan speed setting.

10.SET ALARM FOR END OF STAGE (‘ON-OFF’).

Upper Display shows

*Lower Display flashing with current alarm setting*

Rotate ‘Timer’ knob to select desired alarm state which will be shown on the Lower Display.

‘ON’ - Alarm sounds at completion of the cooking stage, the program is paused awaiting user action. Without any input, the program

will automatically resume after 1 minute.

- Press ‘Timer-Start/Stop’ key to stop the alarm, resume cooking and to continue to the next cooking stage.

- Open oven door to stop alarm. Close door and press ‘Timer-Start/Stop’ key to continue cooking and to continue on to the

next cooking stage.

‘OFF’ - Oven continues on to the next cooking stage without sounding an alarm.

NOTE: Regardless of the setting applied to the last stage of the program, a Cook Time Completed Alarm will sound to indicate the

end of the program.

Press ‘P’ key to confirm alarm option. Alarm will sound to confirm that all stage parameters have been set.

Repeat Step 1 to Step 10 to program additional stages.

11.EXIT PROGRAMMING MODE.

Press and hold ‘P’ key for 3 seconds until alarm sounds to exit the Programming Mode.

USB Export / Import

The Oven controller is equipped with USB connectivity, through the USB port located on the lower right hand side of the control panel.

The set of programs, P01 - P30, stored in the controller memory can be:

 Written to a USB memory stick (Export).

 Replaced with a set of programs located on the USB stick (Import).

1. To export the set of programs from the controller to the USB stick:

 Ensure the oven is in ‘Standby Mode’ – ‘On / Off’ LED is lit.

 Insert a USB memory stick into the USB port.

 Upper display will show ‘USB’ and lower display will show ‘EPr’ (Export Programs).

 Press ‘Start / Stop’ button.

 Lower display will alternate between ‘rEv’ and ‘001’ (Revision Number e.g. 000 to 999).

(The set of programs can be given a different/new revision number at this point)

 Rotate ‘Timer’ Knob to select revision number required.

 Press ‘Start / Stop’ button to copy programs from controller to USB stick.

If an error message (Err, Er1 or Er2) appears in lower display, refer to

section ‘Fault Finding’

 Lower display will show ‘rUn’, followed by ‘dnE’ once copying is done.

 Remove USB memory stick from USB port.

 Controller will go back to ‘Standby Mode’.

The export feature is useful for backing up the set of programs created in the controller,

creating a copy of the set of programs to apply to another oven, and for editing programs

externally.

2. To import the set of programs to the controller from the USB stick:

 Ensure the oven is in ‘Standby Mode’ - ‘On / Off’ LED is lit.

 Insert a USB memory stick, containing at least one ‘MPRGRXXX.csv’ file into the USB port

(See Section ‘Import / Export Files’).

 Upper display will show ‘USB’ and lower display will show ‘EPr’ (Export Programs).

 Rotate ‘Timer’ knob to change to ‘IPr’ on lower display (Import Programs).

NOTE: IPr will not show on display if a ‘MPRGRXXX.csv’ file is not present.

 Press ‘Start / Stop’ button to copy programs from USB stick to controller.

 If more than one file is present, i.e. MPRGR001, MPRGR002…, the option to select between

these will appear:

 Lower display will alternate between ‘rEv’ and ‘001’ (Revision Number e.g. 000 to 999).

 Rotate ‘Timer’ Knob to select revision number required.

(A maximum of 10 revisions on the USB Stick will be selectable).

 Lower display will show ‘rUn’, followed by ‘dnE’ once copying is done.

 Remove USB memory stick from USB port

 Controller will go back to ‘Standby Mode’.

The import feature is useful for restoring a backed up set of programs, copying programs from another oven, and for loading

programs edited externally.

‘ON / OFF’ LED is ‘On’

when oven is in

‘Stand-By’ Mode.

‘Timer-Start / Stop’ LED

is ‘On’ when oven is in

’Stand-By’ Mode.

USB Export / Import

With the USB connectivity, it is also possible to export / import the parameters that determine the functions of the oven.

The export function described under ‘USB EXPORT / IMPORT – PROGRAMS’, also exports the parameter file ‘PARAM.csv’, so the

process is almost identical:

1. To export the Parameters from the controller to the USB stick:

 Ensure the oven is in ‘Standby Mode’ - ‘On / Off’ LED is lit.

 Insert a USB memory stick into the USB port.

 Upper display will show ‘USB’ and lower display will show ‘EPr’ (Export Programs).

 Press ‘Start / Stop’ button to copy programs from controller to USB stick.

 Lower display will show ‘rUn’, followed by ‘dnE’ once copying is done.

 Remove USB memory stick from USB port.

 Controller will go back to ‘Standby Mode’.

The export feature is useful for backing up the parameters in the controller, or creating

a copy of the set of parameters to apply to another oven.

2. To import the set of parameters from the USB stick to the controller:

 Ensure the oven is in ‘Standby Mode’ - ‘On/Off’ LED is lit.

 Insert a USB memory stick, containing a ‘PARAM.csv’ file, into the USB port

(see Section ‘Import / Export - Files’).

 Upper display will show ‘USB’ and lower display will show ‘EPr’ (Export Programs).

 Rotate ‘Timer’ knob to change to ‘IPr’ on lower display (Import Programs).

 Press ‘Start/Stop’ button to copy parameters from USB stick to controller.

 Lower display will show ‘rUn’, followed by ‘dnE’ once copying is done.

 Remove USB memory stick from USB port.

 Controller will go back to ‘Standby Mode’.

The import feature is useful for restoring a backed up set of parameters, or applying a copy of parameters from another

oven.

‘ON/OFF’ LED is ‘On’

when oven is in ’Stand-

By’ Mode

‘Timer-Start / Stop’ LED

is ‘On’ when oven is in

’Stand-By’ Mode

USB Export / Import

The ‘Set of Programs’, P01-P30, in the controller, has a revision number attached to it, for the purpose of keeping track of changes and

updates to the set of programs stored in the controller or externally on USB Stick / PC.

1. To view the current Program Set Revision Number:

Enter into ‘User Settings’, as described under ‘Controller - User Settings’.

Quick Guide:-

 Place the oven into ‘Standby Mode’ - ‘On / Off’ LED is lit.

 Press and hold ‘Steam’ and ‘Start / Stop’ buttons together until ‘PAS’ is

showing in upper display.

 Rotate ‘Timer’ knob until ‘123’ shows on lower display.

 Press ‘FAN LO’ button.

 Rotate ‘Timer’ knob until parameter ‘PrG’ shows in upper display.

 Lower display will alternate between showing ‘rEu’, (for revision), and the revision

number, i.e. ‘001’.

 The revision number can be edited, if required, in the same manner as other ‘User Settings’.

(Refer to ‘Controller - User Settings’ on the following pages)

Refer section ‘USB Export / Import - Programs’ for further information on using ‘Programs Revision Numbering’.

‘ON/OFF’ LED is ‘On’

when oven is in ’Stand-

By’ Mode

Page is loading ...

Moffat E33D5 Operating instructions

Brand: Moffat

Model: E33D5

Category: Microwaves

Type: Operating instructions

This manual is also suitable for

Download PDF

report