CAME KRONO Installation guide

Category
Gate Opener
Type
Installation guide
KR300 - KR302 - KR310 - KR312
KR510 - KR512
EN English
FA01158-EN
Operator
for swing gates
INSTALLATION MANUAL
p. 2 - Manual FA01158 -EN - 02/2023 - © CAME S.p.A. - Translated original instructions
Danger of hand crushing
Danger! High voltage.
No transiting while the barrier is moving
Danger of foot crushing
WARNING!
important safety instructions for people:
READ CAREFULLY!
PREMISE
• THIS PRODUCT SHOULD ONLY BE USED FOR THE PURPOSE FOR
WHICH IT WAS EXPLICITLY DESIGNED. ANY OTHER USE IS DANGEROUS.
CAME S.P.A. IS NOT LIABLE FOR ANY DAMAGE CAUSED BY
IMPROPER, WRONGFUL AND UNREASONABLE USE • KEEP THESE WARNINGS
TOGETHER WITH THE INSTALLATION AND OPERATION MANUALS THAT COME WITH
THE OPERATOR
.
BEFORE INSTALLING
(CHECKING WHAT'S THERE: IF SOMETHING IS MISSING, DO NOT CONTINUE UNTIL
YOU HAVE COMPLIED WITH ALL SAFETY PROVISIONS)
• CHECK THAT THE AUTOMATED PARTS ARE IN PROPER MECHANICAL ORDER, THAT
THE OPERATOR IS LEVEL AND ALIGNED, AND THAT IT OPENS AND CLOSES PROPERLY.
MAKE SURE YOU HAVE SUITABLE MECHANICAL STOPS • IF THE OPERATOR IS TO BE
INSTALLED AT A HEIGHT OF LESS THAN 2.5 M FROM THE GROUND OR OTHER ACCESS
LEVEL, MAKE SURE YOU HAVE ANY NECESSARY PROTECTIONS AND/OR WARNINGS IN
PLACE • IF ANY PEDESTRIAN OPENINGS ARE FITTED INTO THE OPERATOR, THERE
MUST ALSO BE A A SYSTEM TO BLOCK THEIR OPENING WHILE THEY ARE MOVING
MAKE SURE THAT THE OPENING AUTOMATED DOOR OR GATE CANNOT ENTRAP PEOPLE
AGAINST THE FIXED PARTS OF THE OPERATOR • DO NOT FIT UPSIDE DOWN OR ONTO
ELEMENTS THAT COULD BEND. IF NECESSARY, ADD SUITABLE REINFORCEMENTS TO
THE ANCHORING POINTS • DO NOT INSTALL DOOR OR GATE LEAVES ON TILTED
SURFACES • MAKE SURE ANY SPRINKLER SYSTEMS CANNOT WET THE OPERATOR
FROM THE GROUND UP • MAKE SURE THE TEMPERATURE RANGE SHOWN ON THE
PRODUCT LITERATURE IS SUITABLE TO THE CLIMATE WHERE IT WILL BE INSTALLED
• FOLLOW ALL INSTRUCTIONS AS IMPROPER INSTALLATION MAY RESULT IN SERIOUS
BODILY INJURY • IT IS IMPORTANT TO FOLLOW THESE INSTRUCTIONS FOR THE SAFETY
OF PEOPLE. KEEP THESE INSTRUCTIONS.
INSTALLING
• SUITABLY SECTION OFF AND DEMARCATE THE ENTIRE INSTALLATION SITE TO
PREVENT UNAUTHORIZED PERSONS FROM ENTERING THE AREA, ESPECIALLY MINORS
AND CHILDREN • BE CAREFUL WHEN HANDLING OPERATORS THAT WEIGH OVER
20 KG. IF NEED BE, USE PROPER SAFETY HOISTING EQUIPMENT • ALL OPENING
COMMANDS (THAT IS, BUTTONS, KEY SWITCHES, MAGNETIC READERS, AND SO ON)
MUST BE INSTALLED AT LEAST 1.85 M FROM THE PERIMETER OF THE GATE'S
WORKING AREA, OR WHERE THEY CANNOT BE REACHED FROM OUTSIDE THE GATE.
ALSO, ANY DIRECT COMMANDS (WHETHER BUTTONS, TOUCH PANELS, AND SO ON)
MUST BE INSTALLED AT LEAST 1.5 M FROM THE GROUND AND MUST NOT BE
REACHABLE BY UNAUTHORIZED PERSONS • ALL MAINTAINED ACTION COMMANDS,
MUST BE FITTED IN PLACES FROM WHICH THE MOVING GATE LEAVES AND TRANSIT
AND DRIVING AREAS ARE VISIBLE • APPLY, IF MISSING, A PERMANENT SIGN SHOWING
THE POSITION OF THE RELEASE DEVICE • BEFORE DELIVERING TO THE USERS, MAKE
SURE THE SYSTEM IS EN 12453 STANDARD COMPLIANT (REGARDING IMPACT
FORCES), AND ALSO MAKE SURE THE SYSTEM HAS BEEN PROPERLY ADJUSTED AND
THAT ANY SAFETY, PROTECTION AND MANUAL RELEASE DEVICES ARE WORKING
PROPERLY • APPLY WARNING SIGNS WHERE NECESSARY AND IN A VISIBLE PLACE,
(SUCH AS, SUCH AS THE GATE'S PLATE
SPECIAL USER-INSTRUCTIONS AND RECOMMENDATIONS
• KEEP GATE OPERATION AREAS CLEAN AND FREE OF ANY OBSTRUCTIONS. MAKE
SURE THAT THE PHOTOCELLS ARE FREE OF ANY OVERGROWN VEGETATION AND THAT
THE OPERATOR'S AREA OF OPERATION IS FREE OF ANY OBSTRUCTIONS • DO NOT
ALLOW CHILDREN TO PLAY WITH FIXED COMMANDS, OR TO LOITER IN THE GATE'S
MANEUVERING AREA. KEEP ANY REMOTE CONTROL TRANSMITTERS OR ANY OTHER
COMMAND DEVICE AWAY FROM CHILDREN, TO PREVENT THE OPERATOR FROM BEING
ACCIDENTALLY ACTIVATED. • THE APPARATUS MAY BE USED BY CHILDREN OF EIGHT
YEARS AND ABOVE AND BY PHYSICALLY, MENTALLY AND SENSORY-CHALLENGED
PEOPLE, OR EVEN ONES WITHOUT ANY EXPERIENCE, PROVIDED THIS HAPPENS UNDER
CLOSE SUPERVISION OR ONCE THEY HAVE BEEN PROPERLY INSTRUCTED TO USE THE
APPARATUS SAFELY AND TO THE POTENTIAL HAZARDS INVOLVED. CHILDREN MUST
NOT PLAY WITH THE APPARATUS. CLEANING AND MAINTENANCE BY USERS MUST
NOT BE DONE BY CHILDREN, UNLESS PROPERLY SUPERVISED • FREQUENTLY CHECK
THE SYSTEM FOR ANY MALFUNCTIONS OR SIGNS OF WEAR AND TEAR OR DAMAGE
TO THE MOVING STRUCTURES, TO THE COMPONENT PARTS, ALL ANCHORING POINTS,
INCLUDING CABLES AND ANY ACCESSIBLE CONNECTIONS. KEEP ANY HINGES, MOVING
JOINTS AND SLIDE RAILS PROPERLY LUBRICATED • PERFORM FUNCTIONAL CHECKS
ON THE PHOTOCELLS AND SENSITIVE SAFETY EDGES, EVERY SIX MONTHS. TO CHECK
WHETHER THE PHOTOCELLS ARE WORKING, WAVE AN OBJECT IN FRONT OF THEM
WHILE THE GATE IS CLOSING; IF THE OPERATOR INVERTS ITS DIRECTION OF TRAVEL
OR SUDDENLY STOPS, THE PHOTOCELLS ARE WORKING PROPERLY. THIS IS THE ONLY
MAINTENANCE OPERATION TO DO WITH THE POWER ON. CONSTANTLY CLEAN THE
PHOTOCELLS' GLASS COVERS USING A SLIGHTLY WATER-MOISTENED CLOTH; DO NOT
USE SOLVENTS OR OTHER CHEMICAL PRODUCTS THAT MAY RUIN THE DEVICES • IF
REPAIRS OR MODIFICATIONS ARE REQUIRED TO THE SYSTEM, RELEASE THE OPERATOR
AND DO NOT USE IT UNTIL SAFETY CONDITIONS HAVE BEEN RESTORED • CUT OFF
THE POWER SUPPLY BEFORE RELEASING THE OPERATOR FOR MANUAL OPENINGS AND
BEFORE ANY OTHER OPERATION, TO PREVENT POTENTIALLY HAZARDOUS SITUATIONS.
READ THE INSTRUCTIONS IF THE POWER SUPPLY CABLE IS DAMAGED, IT MUST
BE REPLACED BY THE MANUFACTURER OR AUTHORIZED TECHNICAL ASSISTANCE
SERVICE, OR IN ANY CASE, BY SIMILARLY QUALIFIED PERSONS, TO PREVENT ANY
RISK • IT IS FORBIDDEN FOR USERS TO PERFORM ANY OPERATIONS THAT ARE NOT
EXPRESSLY REQUIRED OF THEM AND WHICH ARE NOT LISTED IN THE MANUALS.
FOR ANY REPAIRS, MODIFICATIONS / ADJUSTMENTS, AND FOR EXTRA-ORDINARY
MAINTENANCE, CALL TECHNICAL ASSISTANCE • LOG THE JOB AND CHECKS INTO
THE PERIODIC MAINTENANCE LOG.
FURTHER RECOMMENDATIONS FOR ALL
KEEP CLEAR OF HINGES AND MECHANICAL MOVING PARTS • DO NOT ENTER
THE OPERATOR'S AREA OF OPERATION WHEN IT IS MOVING • DO NOT COUNTER
THE OPERATOR'S MOVEMENT AS THIS COULD RESULT IN DANGEROUS SITUATIONS
• ALWAYS PAY SPECIAL ATTENTION TO ANY DANGEROUS POINTS, WHICH HAVE TO
BE LABELED WITH SPECIFIC PICTOGRAMS AND/OR BLACK AND YELLOW STRIPES
WHILE USING A SELECTOR SWITCH OR A COMMAND IN MAINTAINED ACTIONS, KEEP
CHECKING THAT THERE ARE NO PERSONS WITHIN THE OPERATING RANGE OF ANY
MOVING PARTS, UNTIL THE COMMAND IS RELEASED • THE GATE MAY MOVE AT
ANY TIME AND WITHOUT WARNING • ALWAYS CUT OFF THE MAINS POWER SUPPLY
BEFORE PERFORMING ANY MAINTENANCE OR CLEANING
.
0
200
400
600
800
1000
1200
2 2,5 3 3,5 4 4,5 5 5,25
KR510 - KR512
KR300 - KR302 - KR310 - KR312
p. 3 - Manual FA01158 -EN - 02/2023 - © CAME S.p.A. - Translated original instructions
Technical data
Type KR300 - KR310 KR302 - KR312 KR510 KR512
Protection rating (IP) 54 54 54 54
Power supply (V - 50/60 Hz) 230 AC 230 AC 230 AC 230 AC
Power supply motor (V) 230 AC 230 AC 230 AC 230 AC
Max draw (A) 1.1 1.1 1.1 1.1
Power (W) 240 300 240 300
Thrust (N) 400 ÷ 3000 400 ÷ 3000 400 ÷ 3000 400 ÷ 3000
Opening time at 90° (s) 22 18 34 30
Duty cycle (%) 30303030
Operating temperature (°C) -20 ÷ +55 -20 ÷ +55 -20 ÷ +55 -20 ÷ +55
Condenser (μF) 8 8 8 8
Motor's thermal monitoring (°C) 150 150 150 150
Weight (Kg) 10 10 12 12
DESCRIPTION
KR300 - KR302 Irreversible gearmotor for swing gates with leaves of up to 3 m long.
KR310 - KR312 Irreversible gearmotor for swing gates with leaves of up to 3 m long with opening and closing limit-switch micro switches.
KR510 - KR512 Irreversible gearmotor for swing gates with leaves of up to 5 m long with opening and closing limit-switch micro switches.
Intended use
This gearmotor is designed to power and operate swing gates in private homes and apartment blocks.
Any installation and/or use other than that specifi ed in this manual is forbidden.
Limits to use
LEGEND
This symbol shows which parts to read carefully.
This symbol shows which parts describe safety issues
This symbol shows which parts to tell users about.
Gate-leaf weight (Kg)
Gate-leaf length (m)
We suggest you always fi t an electrolock onto swing gates for a more reliable closure.
You must install electrolocks onto irreversible operators with gate leaves exceeding 2.5 m.
113
234
956 * - 1356 **
304 * - 504 **
KR300 - KR302 - KR310 - KR312 KR510 - KR512
p. 4 - Manual FA01158 -EN - 02/2023 - © CAME S.p.A. - Translated original instructions
Standard installation
1. Left-side gearmotor
2. Right-side gearmotor
3. Flashing light
4. Antenna
5. Control device
6. Photocells
7. Photocells post
8. Mechanical gate stop
9. Junction pit
10. Control panel
Description of parts
1. Gearmotor
2. Cover
3. Post braces with bushing, fastening screw and self-locking nut
4. Gates braces with grower elastic washer and self-locking nut
5. Limit-switch adjusting screws
6. Release lock
7. Release lever
8. Pinion
9. Cover-fastening screw
Dimensions
(mm)
p. 5 - Manual FA01158 -EN - 02/2023 - © CAME S.p.A. - Translated original instructions
GENERAL INSTALLATION INDICATIONS
Only skilled, qualified staff must install this product.
Preliminary checks
Before beginning, do the following:
• check that the gate structure is sturdy enough, the hinges work efficiently and that there is no friction between the fixed and moving parts;
• make sure that measurement C does not exceed the value shown in the reference table;• make sure you have fitted opening and closing
mechanical gate stops;
• make sure that the point where the gearmotor is fastened is protected from any impacts and that the anchoring surface is solid enough;
• make sure you have set up a suitable dual pole cut off device along the power supply that is compliant with the installation rules. It should
completely cut off the power supply according to category III surcharge conditions (that is, with minimum contact openings of 3 mm);
make sure that any connections inside the container (ones that ensure continuity to the protection circuit) are fitted with additional insulation
with respect to those of other electrical parts inside:
•set up suitable tubes and conduits for the electric cables to pass through, making sure they are protected from any mechanical damage.
Tools and materials
Make sure you have all the tools and materials you will need for installing in total safety and in compliance with applicable regulations. The figure
shows some of the equipment installers will need.
Cable types and minimum thicknesses
Connection Cable type Cable length
1 < 15 m
Cable length
15 < 30 m
Control panel power supply 230 V AC
H05RN-F
3G x 1,5 mm23G x 2,5 mm2
Power supply to motor 230 V AC 4G x 1,5 mm24G x 2,5 mm2
Flashing light 2 x 0,5 mm2
Photocell transmitters FROR CEI 20-22
CEI EN
50267-2-1
2 x 0,5 mm2
Photocell receivers 4 x 0,5 mm2
Command and safety device 2 x 0,5 mm2
Antenna RG58 max 10 m
If cable lengths di er from those specifi ed in the table, establish the cable sections depending on the actual power draw of the connected
devices and according to the provisions of regulation CEI EN 60204-1.
For multiple, sequential loads along the same line, the dimensions on the table need to be recalculated according to the actual power draw and
distances. For connecting products that are not contemplated in this manual, see the literature accompanying said products.
E
p. 6 - Manual FA01158 -EN - 02/2023 - © CAME S.p.A. - Translated original instructions
Fastening the braces
Establish the point the gate and post braces will be fitted, while respecting the quotas shown on the table.
The greater the gate leaf's opening angle, the greater the opening speed and the slower is the gearmotor's thrust.
The smaller the gate leaf's opening angle, the slower the opening speed and the greater is the gearmotor's thrust.
Application dimension (mm)
KR300 - KR302 - KR310 - KR312
Leaf opening arc (°) A B C MAX E
90° 130 130 60 910
120° 130 110 50 910
KR510 - KR512
Leaf opening arc (°) A B C MAX E
90° 200 200 120 1310
130° 200 140 70 1310
INSTALLATION
The following illustrations are just examples, in that the space available for fitting the operator and accessories varies depending on the overall
dimensions. It is up to the installer to find the most suitable solution.
The drawings refer to the left-side gearmotor. Install the operator on the right, symmetrically.
Corrugated tube laying
Fit junction boxes and corrugates tubes for incoming connections from the junction pit.
The number of tubes depends on the type of system and the accessories you
are going to fit.
Gate bracket
Post bracket
p. 7 - Manual FA01158 -EN - 02/2023 - © CAME S.p.A. - Translated original instructions
Assemble and weld the two parts of the post brace.
Fasten the brace to the established point, using suitable plugs and screws. If the post is metallic, weld the brace.
Weld the gate brace to the leaf following the measurements shown on the table.
On non-metallic leaves, assemble and weld the two parts of the brace - use suitable screws to fasten.
W V U W V U
ZA3N - ZA3P
p. 8 - Manual FA01158 -EN - 02/2023 - © CAME S.p.A. - Translated original instructions
Open the leaf, fit the pinion into the gate brace and fasten it using the supplied washer and nut.
Connecting to the control panel
Warning! Before working on the control panel, cut off the main current supply and, if present, remove any batteries.
Fastening the gearmotor
Lubricate the bushing and fit into one of the post brace holes (the holes on the brace are for varying the gate's opening angle.
Fasten the joint to the post brace using the bolt and nut.
230 V AC gearmotor fi tted on the left (inside
view), with delayed opening.
230 V AC gearmotor fi tted on the right (inside
view), with delayed closing.
p. 9 - Manual FA01158 -EN - 02/2023 - © CAME S.p.A. - Translated original instructions
Establishing the limit-switch points
Before establishing the limit-switch points, you must remove the cover by loosening the fastening screw.
For closing
Release the gearmotor.
Push the leaf to its closing strike position.
Send a (2-4) closing command and turn the threaded rod counter clock-wise until the closing microswitch activates to stop the gearmotor.
Leave the nut loose on the threaded rod.
Do the same procedure for the right-side gearmotor.
The closing microswitches are positioned at the far ends of their travel range.
A
B
p. 10 - Manual FA01158 -EN - 02/2023 - © CAME S.p.A. - Translated original instructions
INWARD OPENING CONNECTIONS AND INSTALLING
Fastening the braces
Measure quotas A and B (while respecting the quotas shown on the table) to establish the point where the post brace joined with non-supplied
supplementary brace will be fastened.
Application dimension (mm)
KR300 - KR302 - KR310
Leaf opening arc (°) A B E
90° 130 130 910
KR510 - KR512
Leaf opening arc (°) A B E
90° 200 200 1310
For opening
Release the gearmotor.
Reach the wanted leaf-opening point.
Send a (2-3) opening command and turn the threaded rod clockwise until the microswitch activates to stop the gearmotor.
Leave the nut loose on the threaded rod.
Do the same procedure for the right-side gearmotor.
E
p. 11 - Manual FA01158 -EN - 02/2023 - © CAME S.p.A. - Translated original instructions
Open the gate to 9, weld or fasten the gate brace using suitable bolts (while respecting quota E as shown in the table).
Assemble and weld the supplementary brace to the post brace. Fasten the supplementary brace to the post.
Fasten the gearmotor to the braces by using the supplied nuts and bolts.
ZA3N - ZA3P
W V U W V U
p. 12 - Manual FA01158 -EN - 02/2023 - © CAME S.p.A. - Translated original instructions
Establishing the limit-switch points
Carefully follow the previous description.
To establish the opening limit-switch point, use the threaded rod .
To establish the closing limit-switch point, use the threaded rod .
230 V AC gearmotor fi tted on the left (inside
view), with delayed opening.
230 V AC gearmotor fi tted on the right (inside
view), with delayed closing.
Connecting to the control panel
Warning! Before working on the control panel, cut off the main current supply and, if present, remove any batteries.
90°
90°
p. 13 - Manual FA01158 -EN - 02/2023 - © CAME S.p.A. - Translated original instructions
RELEASING
LOCKING
RELEASING THE GEARMOTOR
This procedure must be done with the main power cut o .
The gearmotor's manual release may cause unwanted movement of the gate, if the latter has any mechanical issues or if it is not balanced.
FINAL OPERATIONS
Proceed with the fi nal steps, only once you have completed all connections and made the gate operational.
Fit the cover and fasten the screw.
p. 14 - Manual FA01158 -EN - 02/2023 - © CAME S.p.A. - Translated original instructions
MAINTENANCE
Periodic maintenance
Before doing any maintenance, cut off the power supply, to prevent any hazardous situations caused by accidentally activating the operator.
Periodic maintenance log kept by users (every six months)
Date Notes Signature
TROUBLESHOOTING
TROUBLES POSSIBLE CAUSES FIXES
It neither opens
nor closes
• Power supply missing
• The gearmotor is stuck
• The transmitter's battery is run down
• The transmitter is broken
• The stop button is either stuck or broken
• The opening/closing button or the key-switch selector is stuck
• Check main power supply
• Lock the gearmotor
• Replace the batteries
• Call for assistance
• Call for assistance
• Call for assistance
The gate opens
but does not close
• The photocells are soiled. • Clean and check that the photocells work
properly. Otherwise call for assistance
p. 15 - Manual FA01158 -EN - 02/2023 - © CAME S.p.A. - Translated original instructions
Extraordinary maintenance
The following table is for logging any extraordinary maintenance jobs, repairs and improvements performed by specialized contractors.
Any extraordinary maintenance jobs must be done only by specialized technicians.
Extraordinary maintenance log
Fitter's stamp Name of operator
Job performed on (date)
Technician's signature
Requester's signature
Job performed __________________________________________________________________________________________
____________________________________________________________________________________________________
__________________________________________________________________________________________
Fitter's stamp Name of operator
Job performed on (date)
Technician's signature
Requester's signature
Job performed __________________________________________________________________________________________
____________________________________________________________________________________________________
__________________________________________________________________________________________
DISMANTLING AND DISPOSAL
CAME S.p.A. applies a certified Environmental Management System at its premises, which is compliant with the UNI EN ISO 14001 standard
to ensure the environment is safeguarded.
Please continue safeguarding the environment. At CAME we consider it one of the fundamentals of our operating and market strategies. Simply
follow these brief disposal guidelines:
DISPOSING OF THE PACKAGING
The packaging materials (cardboard, plastic, and so on) should be disposed of as solid urban waste, and simply separated from other waste for
recycling.
Always make sure you comply with local laws before dismantling and disposing of the product.
DO NOT DISPOSE OF IN NATURE!
DISMANTLING AND DISPOSAL
Our products are made of various materials. Most of these (aluminum, plastic, iron, electrical cables) is classified as solid household waste. They
can be recycled by separating them before dumping at authorized city plants.
Whereas other components (control boards, batteries, transmitters, and so on) may contain hazardous pollutants.
These must therefore be disposed of by authorized, certified professional services.
Before disposing, it is always advisable to check with the specific laws that apply in your area.
DO NOT DISPOSE OF IN NATURE!
Fitter's stamp Name of operator
Job performed on (date)
Technician's signature
Requester's signature
Job performed __________________________________________________________________________________________
____________________________________________________________________________________________________
__________________________________________________________________________________________
CAME S.p.A.
Via Martiri Della Libertà, 15
31030 Dosson di Casier - Treviso - Italy
tel. (+39) 0422 4940 - fax. (+39) 0422 4941
[email protected] - www.came.com
Manual FA01158-EN - 02/2023 - © CAME S.p.A. - Translated original instructions
The contents of this manual may change, at any time, and without notice.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

CAME KRONO Installation guide

Category
Gate Opener
Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI