Treadmill Owner’s Manual
Bladez DX7T-ME
BH North America Corporation
20155 Ellipse
Foothill Ranch, CA 92610
Phone: 949-206-0330
Fax: 949-206-0013
Email: 0H[email protected]
BH North America • 20155 Ellipse • Foothill Ranch • CA • 92610
• Phone 949-206-0330 • Fax 949-206-0013
1
INTRODUCTION:
Congratulations for selecting BH as your primary source of fitness.
BH treadmills offer many exercise programs that benefit users of all levels
and ages. Your new treadmill is designed to make your workouts more effective
and enjoyable. Please read this entire manual carefully before using your
treadmill. This will allow you to get a full understanding of all the features your
BH treadmill provides. If you have any questions or concerns, please
contact the BHNorth America or any authorized distributors in your area
.
BH North America Corporation
20155 Ellipse
Foothill Ranch, CA 92610
Phone: 949-206-0330
Fax: 949-206-0013
Email: 1H
BEFORE YOU BEGIN
It is very important to become familiar with the frequently used components of
your BH treadmill.
www.bhnorthamerica.com
2
TABLE OF CONTENTS
1. IMPORTANT SAFETY INSTRUCTIONS ...................................................... 3
2. ASSEMBLY INSTRUCTIONS....................................................................... 5
3. GETTING STARTED ....................................................................................10
4. WORKOUT PROGRAM DETAILS................................................................14
5. USING YOUR LCD DISPLAY.......................................................................18
6. PROGRAM PROFILES ................................................................................20
7. PREVENTIVE MAINTENANCE....................................................................22
8. TROUBLESHOOTING .................................................................................23
9. WARRANTY .................................................................................................25
Section Page
BH North America • 20155 Ellipse • Foothill Ranch • CA • 92610
• Phone 949-206-0330 • Fax 949-206-0013
www.bhnorthamerica.com
3
SECTION 1
IMPORTANT SAFETY INSTRUCTIONS
Read all instructions before using the treadmill.
Notice: Before using this or any other exercise equipment consult your family physician
or health care professional to develop a well planned exercise program to fit your health
needs. If you encounter any pain or breathing discomfort while working out, STOP!,and
consult a physician before continuing
WARNING!
1. It is wise to always unplug this appliance from the electrical outlet immediately after
use.
2. Keep children away from the machine while in use.
3. Do not wear loose or dangling clothing while using the treadmill.
4. Keep a minimum clearance of 18” on each side and 24” at the rear of the treadmill for
safety.
5. It is mandatory that you unplug the treadmill prior to cleaning to reduce the risk of
electric shock, serious burns, and the risk of injuries.
6. The treadmill should never be left unattended when in operation. Unplug the treadmill
from the outlet when not in use or when servicing the treadmill.
7. Close supervision is necessary when this appliance is used by or near children,
8. Use this appliance only for its intended use as described in this manual
.
Do not use any attachment not recommended by the manufacturer.
9. Never operate this appliance if it has a damaged cord or plug, or if it is not working
properly. Call your service center for any service concerns before taking your treadmill
in for repair.
10. Keep the cord away from heated surfaces.
11. Never drop or insert any object into any opening.
12. Do not use outdoors.
13. Do not operate where aerosol (spray) products are being used or where oxygen is
being administered.
14. To disconnect, turn all controls to the off position, then remove plug from outlet.
15. Connect this appliance to a properly grounded outlet only.
16. This appliance is intended for household use only.
SAVE THESE INSTRUCTIONS
BH North America • 20155 Ellipse • Foothill Ranch • CA • 92610
• Phone 949-206-0330 • Fax 949-206-0013
www.bhnorthamerica.com
4
IMPORTANT SAFETY INSTRUCTIONS CONTINUED
GROUNDING INSTRUCTIONS
This product must be grounded. If it malfunctions or breaks down, grounding
provides a path of least resistance for electric currents, to reduce the risk of
electric shock. This product is equipped with a cord that has an equipment-
grounding conductor and a grounding plug. The plug must be plugged into an
appropriate outlet that is properly installed and grounded in accordance with all
local codes and ordinances.
WARNING! – An improper connection of the equipment grounding conductor
can result in a risk of an electrical shock. Check with a qualified electrician if you
are in doubt as to whether the product is properly grounded. Do not modify the
plug provided to you. If it does not fit the outlet, have a proper outlet installed by
a qualified electrician.
This product is for use on a nominal 110-120-volt circuit and has a grounding
plug that looks like the plug illustrated in the figure. Make sure that the product is
connected to an outlet having the same configuration as the plug. No adapter or
extension cord should be used with this product.
GROUNDING METHODS
GROUNDED OUTLET
GROUNDING
PIN
BH North America • 20155 Ellipse • Foothill Ranch • CA • 92610
• Phone 949-206-0330 • Fax 949-206-0013
www.bhnorthamerica.com
5
SECTION 2
ASSEMBLY INSTRUCTIONS
ITEM Description Qty
A Computer Console
B Frame
C Upright (L)
D Upright(R)
E Decorative Cover (L)
F Decorative Cover(R)
G Handrail (L)
H Handrail (R)
I Handrail Cover (L)
J Handrail Cover(R)
K Bottle
1
1
1
1
1
1
1
1
1
1
1
BH North America • 20155 Ellipse • Foothill Ranch • CA • 92610
• Phone 949-206-0330 • Fax 949-206-0013
www.bhnorthamerica.com
6
ASSEMBLY INSTRUCTIONS CONTINUED
ITEM Description Qty
a Screw M5x0.8x15
b Self Tapping Screw ψ5x25 2
c Allen Bolt ψ13 M8xP1.25x60 4
d Allen Bolt M8xP1.25x1 510
e Allen Wrench 5mm
f Allen Wrench 6mm
g Safety Key/Clip
h SILICON 1
i Power Cord
j TV Remote Controller
k MP3 Sound Wire
l Magazine Shelf
4
1
1
1
1
1
1
1
BH North America • 20155 Ellipse • Foothill Ranch • CA • 92610
• Phone 949-206-0330 • Fax 949-206-0013
www.bhnorthamerica.com
7
ASSEMBLY INSTRUCTIONS CONTINUED
A minimum of two people are required
to assemble this treadmill. Also, READ
and understand ALL INSTRUCTIONS
thoroughly BEFORE ASSEMBLING the
treadmill.
1. Pull out the Control Wire with the Guide
Thread in the right Upright. Insert the
Control Wire into the hole on the side of
the right Upright. Attach the Uprights (C,
D) to the frame with Bolt (d).
• Ensure that the wire is not pinched
between the upright and the treadmill
base when securing the upright.
2. After the Uprights are tightened, insert
the Decorative Covers (E, F) into the
Frame and tighten with Screw (a).
3.
BH North America • 20155 Ellipse • Foothill Ranch • CA • 92610
• Phone 949-206-0330 • Fax 949-206-0013
www.bhnorthamerica.com
8
ASSEMBLY INSTRUCTIONS CONTINUED
3. Connect the cables for the Pulse
Sensors, Elevation and Speed
Switches in the Handrails to the
cables from the Computer Shelf.
Insert the Handrails (G, H) into the
frame in the direction shown in
drawing.
4. Place the Computer Shelf on the
top of the assembled frame.
Thread the Control Wire and Cable
Wire of the Upright into the tube,
and then pull them out from the
upper hole on the Computer Shelf.
Then place the Computer Shelf on
the Upright and tighten with Allen
Bolt (c).
Note: When you tighten the screws,
make sure not to damage the
Control wire and Cable wire in the
tube.
BH North America • 20155 Ellipse • Foothill Ranch • CA • 92610
• Phone 949-206-0330 • Fax 949-206-0013
www.bhnorthamerica.com
9
ASSEMBLY INSTRUCTIONS CONTINUED
5. After the above is done, attach the
Handrail Cover (I, J) to the
Computer Shelf and tighten with Self
Tapping Screw (b), and then
assemble the Magazine Shelf (p) in
the direction shown in the drawing.
Note: When you tighten the screws, make
sure not to damage the control wire
in the tube.
BH North America • 20155 Ellipse • Foothill Ranch • CA • 92610
• Phone 949-206-0330 • Fax 949-206-0013
www.bhnorthamerica.com
10
SECTION 3
GETTING STARTED
FOLDING:
To fold your treadmill into the upright position, first be sure to set the elevation to 0 %
incline. The treadmill will not lock into the upright position if the treadmill is not at 0 %
incline.
Using both hands, lift the treadmill by the end caps at the rear of the treadmill and push it
up until the retaining shaft locks the treadmill into place.
UNFOLDING:
To unfold the treadmill from the upright position simply depress the unfolding pedal with
your foot and guide the deck down with both hands. Make sure that you do not let go until
the deck is firmly on the floor.
MOVING THE TREADMILL
The treadmill will need to be locked in the upright position as illustrated above.
Grasp the end caps with two hands and slowly pull the deck down towards your body until
the casters are able to roll freely. Keep the treadmill at that angle until you are done with
your move.
BH North America • 20155 Ellipse • Foothill Ranch • CA • 92610
• Phone 949-206-0330 • Fax 949-206-0013
www.bhnorthamerica.com
11
GETTING STARTED CONTINUED
SAFETY KEY & CLIP
Your Bladez treadmill is equipped with a safety key that will disable the treadmill if it is not
in place. You should attach the clip end to your clothing. The magnet end goes into the
recess of the console. If at any time you need to stop the treadmill quickly simply pull the
safety key off the console. This will cut all power to the treadmill and it will come to a
complete stop. To resume your workout, place the safety key back in place. You will then
need to program your workout again.
BH North America • 20155 Ellipse • Foothill Ranch • CA • 92610
• Phone 949-206-0330 • Fax 949-206-0013
www.bhnorthamerica.com
12
GETTING STARTED CONTINUED
BEFORE STARTING
Do not stand on the walking belt while starting or stopping the treadmill. Straddle the
running belt and stand on the side rails.
I. TV-OSD Start Display:
1. After you start the treadmill, the window will display weight unit KGS/LBS:
Metric unit KGS pre-set value is 70.
English unit LBS pre-set value is 150.
Pre-set value will be displayed and set in the WEIGHT window. Press to
change the value. This value along with others is used to determine the number of
calories burned during your workout.
Press ” ” to go into the ready start mode.
2. Put the safety key in the recess of the console.
A beep will sound and all windows will display values. The initial values are 0, and
then heart shape will blink in the window. This shows the treadmill is in
START/READY mode. In this mode, the user can hold the grip pulse sensor to
detect the user’s heart rate value.
3. After you start the treadmill, if you remove the SAFETY KEY, the window shows a
blinking .↓
** If the safety key/ clip is not placed in the recess of the console, LED windows will
display “----“, and the treadmill can’t be operated normally.
** During work out, if the safely key/clip is removed, a beep will sound for warning,
then the treadmill will stop operation. If you put the safety key back into the recess
of the console, then all the values will go back to initial values.
** Under START/READY condition, if you do not hold the grip pulsesensors, then the
PULSE window will display HP. When you hold both of the handgrips for at least 10
seconds, the PULSE window display the heart rate value.
** PULSE display range: 40~240 Beats/min.
BH North America • 20155 Ellipse • Foothill Ranch • CA • 92610
• Phone 949-206-0330 • Fax 949-206-0013
www.bhnorthamerica.com
13
GETTING STARTED CONTINUED
** The table below shows the relationship between the optimum amount of running
under different age and heart rate:
170 OVER
150 166 MIDDLE
120 146 162 LOW
117 143 157
114 137 153
111 135 149
108 131 145
105 128 140
102 124 136
99 120 132
96 116
HEART BEATS/MIN
93
20 25 30 35 40 45 50 55 60 65 (Age)
II. Operation instructions:
1. In START/READY mode, press” ”, the system enters and starts Manual run.
2. Press” ”to start treadmill. The treadmill will start with a speed of 0.8 km/hr
(0.5MPH). At this time press ,to increase/decrease speed (you can also press
instant buttons to select the desired speed). Press ” ”tostopthe
workout, (press ” ” once, all values will freeze and the treadmill will pause for 4
minutes and then reset to the START/READY status. If you press ” ” once, then
press a second time and hold the ” ” button for 3 seconds, the treadmill will
automatically reset to the START/READY status).
3. If you press ” ”when the motor is running, the motor stops, inclination motor
stops and returns to start and the time window displays ”Stop”；if you press ” ”,
the motor will re-start after 3 seconds count down. The speed will be maintained
the same as it was before the stop and the incline will be maintained the same as
it was before the stop.
4. This treadmill is equipped with an inclination adjustment, which accommodates
treadmill incline by stages. Press , to adjust the inclination of the treadmill (you
can also press instant buttons to select the desired inclination). Press
,continuously, the treadmill changes inclination adjustment, when you get to the
inclination you want, release the button.
** Segment inclination: 0-15 levels.
5. Besides using the control button on theconsole, the control button on the handrail
can also be used to adjust speed and elevation. The control button on the left
handrail is for elevation while the right handrail button is for speed adjustment.
**Range of speed: Metric unit 0.8~18 km/hr, Step: 0.1 km/hr.
English Unit 0.5~11 mile/hr, Step: 0.1 mile/hr.
BH North America • 20155 Ellipse • Foothill Ranch • CA • 92610
• Phone 949-206-0330 • Fax 949-206-0013
www.bhnorthamerica.com
14
SECTION 4
WORKOUT PROGRAM DETAILS
MODE Operation Instructions (This mode includes MANUAL and 6 pre-set
PROGRAMS):
6. MANUAL: In this mode you can set the time and distance freely, the operation
method is shown below:
6.1. Press, ” ”, and you will see the MANUAL LED light blinking. Press ” ” to enter
the MANUAL mode.
6.2. At this time, you can press ,
to set the time. When finished, press
”to
start your workout, or press ” ” to come back to the MODE selection.
**Program Preset value is 20 min; Range of time:20~99 min, Step is 1 min.
7. PROGRAM MODE: This mode includes 6 patterns, P1~P6, you can choose the
desired mode to use. The operation method is shown below:
7.1 Press” ”, when the MANUAL LED light is blinking. Press ,to choose any
mode from P1 to P6. Press ” ” to enter the mode you have chosen.
7.2 You will see the TIME window blinking after you enter the program control function.
Press ,to set the exercise time you want or press ” ” directly to start
running without counting down. (** Range of time: 20~99 min; preset value is
30min, step is 1)
7.3 There are 30 stages in PROGRAM. The first 3 stages for WARM UP, the last 3
stages for COOL DOWN, each are 3 minutes. After deducting 6 minutes for the first
and last stage, the rest of the 24 stages will be executed evenly in the PROGRAM.
III. Program Mode
1. MANUAL RUN:
When choosing this mode, the program will ask you to enter the following values:
Time: pre-set 30min: Range 20~99min: step 1min.
After setting up the correct value, press ” ” to return to MODE or press ” ”to
start the workout.
2. 9 HOLE WALK (P1)
The window will show the program drawing, and the windows of speed and
elevation will show the max range of speed and elevation in this program. The
speed led window will be flashing. Press INCLINE ” ,” to select the speed.
Press ” ”and the incline led window will be flashing. Press INCLINE ” ,”to
select the elevation. After finishing the setting, press ” ”or ” ” to start running.
The unit will stop after 3.5 KM or 2.17 miles. The elevation level will go back to zero,
and the display will show ”End”.
BH North America • 20155 Ellipse • Foothill Ranch • CA • 92610
• Phone 949-206-0330 • Fax 949-206-0013
www.bhnorthamerica.com
15
WORKOUT PROGRAM DETAILS CONTINUED
3. HILL CLIMB (P2):
When choosing this mode, the program will ask you to enter the following values:
Time: pre-set 30min: Range 20~99min: step 1min. After setting up correct value,
press ” ”to set next value.
The window will show the program drawing, and the windows of speed and
elevation will show the max range of speed and elevation in this program. The
speed led window will be flashing. Press INCLINE ” ,” to select the speed.
Press ” ”, the incline led window will be flashing, Press INCLINE ” ,”to
select the elevation. After finishing the setting, press ” ”or ” ” to start running.
4. ENDURANCE RUN (P3):
When choosing this mode, the program will ask you to enter the following values:
Time: pre-set 30min: Range 20~99min: step 1min. After setting up correct value,
press ” ”to set next value.
The window will show the program drawing, and the windows of speed and
elevation will show the max range of speed and elevation in this program. The
speed led window will be flashing. Press INCLINE ” ,” to select the speed.
Press ” ”, the incline led window will be flashing. Press INCLINE” ,”to
select the elevation. After finishing the setting, press ” ”or ” ” to start running.
5. INTERVAL RUN (P4):
When choosing this mode, the program will ask you to enter the following values:
Time: pre-set 30min: Range 20~99min: step 1min. After setting up correct value,
press ” ”to set next value.
The window will show the program drawing, and the windows of speed and
elevation will show the max range of speed and elevation in this program. The
speed led window will be flashing. Press INCLINE ” ,” to select the speed.
Press ” ”, the incline led window will be flashing. Press INCLINE ” ,”to
select the elevation. After finishing the setting, press ” ”or ” ” to start running.
6. ROLLING RUN (P5):
When choosing this mode, the program will ask you to enter the following values:
Time: pre-set 30min: Range 20~99min: step 1min. After setting up correct value,
press ” ”to set next value.
The window will show the program drawing, and the windows of speed and
elevation will show the max range of speed and elevation in this program. The
BH North America • 20155 Ellipse • Foothill Ranch • CA • 92610
• Phone 949-206-0330 • Fax 949-206-0013
www.bhnorthamerica.com
16
WORKOUT PROGRAM DETAILS CONTINUED
speed led window will be flashing. Press INCLINE ” ,” to select the speed.
Press ” ”, the incline led window will be flashing. Press INCLINE ” ,”to
select the elevation. After finishing the setting, press ” ”or ” ” to start running.
7. WEIGHT LOSS WALK (P6):
When choosing this mode, the program will ask you to enter the following values:
Time: pre-set 30min: Range 20~99min: step 1min. After setting up correct value,
press ” ”to set next value.
The window will show the program drawing, and the windows of speed and
elevation will show the max range of speed and elevation in this program. The
speed led window will be flashing. Press INCLINE ” ,” to select the speed.
Press ” ”, the incline led window will be flashing. Press INCLINE ” ,”to
select the elevation. After finishing the setting, press ” ”or ” ” to start running.
IV. BodyFat Mode: (Perform this function in Start/Ready position):
1. Under STANDBYposition, press ””, the Body Fat LED light is blinking, which
shows that the Body Fat function is on. When you choose this function, the program
will require the user to enter the following values.
◎Age: Age: Preset value is 30, range: 13~80, Step is 1, choose the correct value with
the ,keys, then press ” ” to go to the next value setting.
◎Height: Preset is 170cm ( 5’7” ), range: 120~200cm ( 3’11”~6’7”), Step is 1cm
(1”)，press ,to adjust, then press ” ”，to go to the next value
setting.
◎Sex: Preset value is one (Male). Press ,to change 1 (Male), 0(Female),
press ” ” to go to the next value setting.
◎Weight: Pre-set value is 70 kg (150LBS), range: 23~130kg (50~286 LBS), Step is
1 kg (2LBS). Press ,to adjust and choose the correct value. Press ” ”,
and hold the grip pulse sensor about 15 seconds. The Body Fat window will
display your Body Fat value, and at the same time, the LED light on the computer
left side will display figure evaluation.
2. As the male and female have different body fat, the figure evaluation light is also
different. See the list below for reference:
Light
Sex
1. (Male) 0.0~4.9 5.0~9.9 10.0~14.9 15.0~19.9 20.0~24.9 25.0~29.9 30.0~34.9 35.0 abo ve
0. (Female) 0.0~14.9 15.0~19.9 20.0~24.9 25.0~29.9 30.0~34.9 35.0~39.9 40.0~44.9 45.0 abo ve
BH North America • 20155 Ellipse • Foothill Ranch • CA • 92610
• Phone 949-206-0330 • Fax 949-206-0013
www.bhnorthamerica.com
17
WORKOUT PROGRAM DETAILS CONTINUED
V. U1. U2. U3. U4. U5. SAVE Buttons Instructions:
1. U1~U5 are used for setting individual in formation. The setting content includes the
values of BODY FAT.
2. Turn on the treadmill, select one of U1~U 5 to set age, height, sex, weigh. After
setting, press” ”for storage and return to Start/Ready status automatically. U1-
U5 is 5 groups with 5 units of integrated values. That means 5 units of data used
for 5 persons.
3. During Setting, press” ” to shift to next item. After finished setting completely,
press” ” for cycle. When set for the first time, all display values are preset
values.
4. When you turn on the treadmill again or the safety key is removed, data set
previously are retained and not replaced by preset values.
5. It is not necessary to set data for the second time when you turn on the treadmill
again or the safety key is removed. The information is saved in the computer after
the first setting. Press user key not enter to this item unless this user resets.
6. Press ””to enter, it will display the data you set when the first time you enter
user and use this function after the treadmill is assembled.
7. Press” ”during exercising or when program run ends, the screen will hold for 10
seconds to permit user to press” ” (To save the data to the corresponding order
of USER based on the order of USER unit occupied by user currently.) During use,
press user to enter individual information mode to check the total distance and the
previous information. So during operation, the related data are mainly based on
USER. After run ends, press ” ” to save values to this user. When used next
time, press USER key, the DISTANCE window will display the total distance of this
user. Every window will display the time, distance, average speed, average heart
rate after 5 seconds. To calculate the average speed and the average heart rate to
decimal points, the average speed displays to the first decimal place, the average
heart rate displays an integral number by rounding off.
8. The calculation of the average speed is the average value of user’s exercise
process from beginning to end; the calculation of the average heart rate is the
average value of user’s exercise process from beginning to end.
9. In the Start /Ready state, hold user key for10 seconds to reset all the values of this
user, including the values set by the first time. At this moment, press this user key
again to set the values identical to that of BODY FAT.
10. During exercising, it does not work if you press user key or ” ”.
11. Segment inclination: 0-15 levels.
12. Hold ” ” for 10 seconds to switch between Metric unit and English unit.
BH North America • 20155 Ellipse • Foothill Ranch • CA • 92610
• Phone 949-206-0330 • Fax 949-206-0013
www.bhnorthamerica.com
18
SECTION 5
USING YOUR LCD DISPLAY
VI. LCD TV USER’S MANUAL:
1. Function Keys:
KEY ITEM FUNCTION DESCRIPTION
1 TV/AV/MP3 TV FUNCTION KEY: Press the key to shift between TV/ AV/MP3.
2DATA
To switch the treadmill data display.
3 MODE MENU system setting
4 CH+ 1. Press it once to skip to the upper channel at the TV position.
2. Press it once to skip to the upper item at the MENU position.
5 CH- 1. Press it once to skip to the lower channel at the TV position.
2. Press it once to skip to the lower item at the MENU position.
6 VOL+ 1. Adjust the volume when playing the TV/AV/MP3，press it to increase the volume.
2. Adjust the values in MENU position, press it to increase and change the set value.
7VOL-
1. Adjust the volume when playing the TV/AV/MP3, press it to decrease the volume.
2. Adjust the values in MENU position, press it to decrease and change the set value.
8 LED LIGHT LCD Power indicator, green for on and red for off.
9IR
RECEIVER
Remote controller receive mode.
2. MENU ITEM SETTING INSTRUCTION
ITEM DESCRIPTION
BRIGHTNESS Adjust BRIGHTNESS. 0 ~ 63
CONTRAST Adjust CONTRAST. 0 ~ 63
SHARP Adjust SHARPNESS. 0 ~ 7
SATURATE Adjust SATURATE. 0 ~ 63
HUE Adjust HUE. 0 ~ 63
RESET Reset to DEFAULT value.
MUTE Sound Off
TV SYSTEM TV system selection. NTSC-M, NTSC-J, PAL-BG, PAL-DK, PAL-AI, SECAM-BG,
SECAM-DK, SECAM-L, you can select one according to the TUNER.
SCAN Scan the channels and save them by pressing this key at the TV mode.
EXIT Press VOL+ or VOL- to leave MENU.
BH North America • 20155 Ellipse • Foothill Ranch • CA • 92610
• Phone 949-206-0330 • Fax 949-206-0013
www.bhnorthamerica.com
19
USING YOUR LCD DISPLAY CONTINUED
3. Keys and descriptions of Remote Control
This treadmill is built with MP3 and Walkman playback features. The MP3 player or
Walkman player should be connected with the enclosed cable. Press the AV/TV/MP3
button on the Computer Console or Remote to select the MP3 playback mode to start the
function.
(Please note that the enclosed cable is not suitable for all brands of MP3 and Walkman
devices.)
BH North America • 20155 Ellipse • Foothill Ranch • CA • 92610
• Phone 949-206-0330 • Fax 949-206-0013
www.bhnorthamerica.com
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
