X Rocker 2.1 Wireless User manual

Brand
X Rocker
Model
2.1 Wireless
Type
User manual

This manual is also suitable for

2.1 Wireless
Need Help? Email: [email protected]
Phone: 866-969-2603
IMPORTANT: You must keep your original retail receipt as proof of purchase.
2
Thank you for purchasing this X Rocker gaming
chair. You are now close to enhancing your
favorite games with audio!
To get started, please assemble the chair using
get rocking!
Table of contents
3 Box contents and control panel overview
4
5
6 Connect by controller (PS4 systems only)
7
8
Welcome to X Rocker!
3
+
+
++
+
+
Control panel overview
B1 - 3m RCA to RCA Audio cable
B2 - 1m 3.5mm to 3.5mm Audio cable
B3 - RCA female to female adapters
B4 - 15cm RCA to 3.5mm audio cable
B5 – 15cm 3.5mm to 3.5mm audio cable
B6 – Power Supply Cable
B
B1
B3
B5 B6
B4
B2
+B7
ON/OFF
4
B7) to your TV set using the 3.5mm to 3.5mm cable (B2/B5)
Once connected, Set the control panel on the chair and the Wireless
1,2,3)
To get the best sound, make sure that the volume on the TV is set to
approximately 50% of the maximum. Depending on the TV you may need
refer to TV manual for guidelines.)
(All consoles)
B5
TV/Mobile/Tablet
ON/OFF
5
1. Connect B1 Cable to X Rocker control panel RCA INPUT sockets
2. Connect B3 RCA adapters to other end of B1 RCA cable
3. Connect B4 RCA cable to B3 Adapter.
4. Connect B4 3.5mm end into the headphone socket of your Television
5. Once connected to your TV, increase volume to 50% of the maximum
for the best sound level.**
*OTE: If your TV does not feature a headphone socket then you may need
console for audio. Contact support for more details.
**Depending on your TV you may need to Increase the headphone
(All consoles)
TV/Mobile/Tablet
B4
ON/OFF
6
1. Connect the B2
headset socket.
2. Connect the other end of the B2 cable to the chair via the green port.
3. With the PS4 turned on, go to the main menu (or locate the main
menu screen). Press and hold
the quick menu appears on screen.
4. In this menu select [Adjust sound and devices]
5. Then select [output to headphones]
6. [Chat Only] to [All audio]
7. Make sure the volume in the previous menu is set to the maximum.
8. Set the control panel Wireless switch to the ‘OFF
Connect by controller:
(PS4 systems only)
B2
7
• Make sure that the power cable is
connected correctly.
• Make sure that the power supply at the
power source is working correctly.
give the power cable a slight wiggle in the
then please contact support (details below).
• Make sure that the wireless channel
(1,2,3 for wireless and AUX for wired
• Please make sure that the volume of
the source device is at a higher level to
strengthen the audio signal.
• Please contact X Rocker support
([email protected]) regarding
this issue.
• In this case, try another of the three
wireless bands to isolate the signal.
No power going to control panel
Issue
No sound
The cables connected to my
X Rocker have been broken
accidentally
8
• Avoid immersing or allowing the X Rocker to come into contact
with liquids.
• Please consult X Rocker Support before unscrewing any of the electrical
components on the chair.
• Please be mindful of any cabling laid out between the X Rocker and
power source/audio device.
the X Rocker.
• If the cables or electrical equipment are broken then this may present
a choking risk, please contact Support for replacements and dispose of
these parts safely.
• Do not stand on the X Rocker or exceed the 250lbs weight limit via
other means.
• If your X Rocker comes with a pedestal,do not lean back on the chair to

• If your X Rocker comes with armrests,X Rocker armrests are designed for
support and comfort during gameplay, please do not use these as support

• Playing audio for long periods at loud volumes may contribute to

• Please be considerate to others when playing audio through the X Rocker
speakers at higher volumes.
Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
FCC NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
7KLVGHYLFHFRPSOLHVZLWK3DUWRIWKH)&&5XOHV2SHUDWLRQLVVXEMHFWWRWKHIROORZLQJWZRFRQGLWLRQV
WKLVGHYLFHPD\QRWFDXVHKDUPIXOLQWHUIHUHQFHDQG
WKLVGHYLFHPXVWDFFHSWDQ\LQWHUIHUHQFHUHFHLYHGLQFOXGLQJLQWHUIHUHQFHWKDWPD\FDXVHXQGHVLUHGRSHUDWLRQ
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
IC
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts. L'exploitation
est autorisée aux deux conditions suivantes :
(1) l'appareil ne doit pas causer d'interférences, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en
compromettre le fonctionnement.
IC Radiation Exposure Statement:
This equipment complies with Canada radiation exposure limits set forth for uncontrolled environments.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Déclaration d’IC sur l’exposition aux radiations:
Cet équipement est conforme aux limites d’exposition aux radiations définies par le Canada pour des environnements
non contrôlés.
Cet émetteur ne doit pas être installé au même endroit ni utilisé avec une autre antenne ou un autre émetteur.
Need Help? Email: 
Phone: "##"$&'
ǁǁ͘džƌŽĐŬĞƌŶĂƚŝŽŶ͘ĐŽŵ

"
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9

X Rocker 2.1 Wireless User manual

Brand
X Rocker
Model
2.1 Wireless
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents