OWNER’S
MANUAL
Date of purchase: _____/ _____/ _____
Clayton 3 PC
Bistro Set
Product code: D71 M80211
UPC code: 7-6945575484-4
1
Vendor Item: AS-I-138-2R/3
PARTS
Read through all the instructions before beginning assembly. Unpack and identify all the parts.
Place them on a flat, non-abrasive surface. Assembly by two people is recommended.
G (1)
Metal
Center Ring
ACCESSORIES
Ha (1 spare)
Short Bolt
Hb (4)
Long Bolt
Hc (1 spare)
Small Metal Washer
Hk (1 spare)
Glass Bumper
2
F (3)
Leg (1 Metal
Washer and 1
Bolt attached
for each)
Hg (4)
Nut
A (2)
Rocker Top
He (3)
Screw
B (2)
Base
Hd (4)
Large Metal Washer
Hh (1)
Hex Open Wrench
C (2)
T Shaped
Connector
D (2)
Center Post
E (1)
Tempered Glass
Tabletop
Hi (1)
Hex Wrench
Hj (1)
Allen Wrench
Hf (4)
Lock Wahser
Hl (1)
Assembly
Instructions Sheet
ASSEMBLY INSTRUCTIONS
Place the rocker top (A) upside down on
your non-abrasive work surface. Attach
the T shaped connector (C) to the bottom
of the rocker seat by inserting a long
bolt (Hb) through a lock washer (Hf),
through the rocker top (A), through the
connector (C), through a large metal
washer (Hd) and secure with a large
nut (Hg) for each hole. See Fig. 1.
Securely tighten the bolts.
Align the connector of the assembled rocker
seat (A, C) with the hole in center post and
push the rocker seat down firmly until fully
engaged. See Fig. 3. Repeat procedure for
the other rocker.
Place the base (B) on flat surface, and
insert the center post (D) into the hole
located at the center of the base (B).
See Fig. 2. Push the center post (D)
down firmly and twist it left and right
as necessary.
1
2
3
3
ROCKER ASSEMBLY
Fig. 1
Fig. 2
Fig. 3
Hg
Hd
Hb
Hf
B
C
A
D
CARE INSTRUCTIONS
Wash with a mild solution of soap and water; rinse thoroughly. Dry completely. Do not use bleach or solvents.
Cover furniture with outdoor furniture covers when not in use.
Made in CHINA
Distributed by Sears, Roebuck and Co., Hoffman Estates, IL 60179
See our extensive assortment of outdoor living products
on-line at www.sears.com and www.kmart.com
For questions or comments about product:
Call toll-free:
800-457-4652
Please refer to part numbers when reordering
Place the tempered glass tabletop (E)
upside down on your non-abrasive work
surface. Remove all bolts (Ha) and metal
washers (Hc) from legs (F).
Attach three legs (F) to the tempered glass
tabletop (E). Insert three legs (F) into the
plastic receivers on tabletop (E), working
the legs in until the holes in the leg line up
with the holes in the receivers. Place the
center ring (G) between three legs. Align
the holes, for each hole insert a short
bolt (Ha) through a small metal washer (Hc),
through the center ring (G) and into the
leg (F). See Fig. 4.
Now go back and securely tighten all the
bolts. Turn the table over.
Your table and rockers are now ready to use.
TABLE ASSEMBLY
4
5
6
Fig. 4
Fig. 5
4
Insert a screw (He) through each receiver
and secure into the tip of the leg. See Fig. 5.
7
E
F
G
He
F
Ha
Hc
G
/