Whirlpool WED8300SB2 Owner's manual

Brand: Whirlpool

Model: WED8300SB2

Category: Electric laundry dryers

Type: Owner's manual

This manual is also suitable for

ELECTRONIC

ELECTRICDRYER

For questions about features, operation/pen%rmance, parts,

accessories or service, call: 1-800-253-1301

or visit our website at... www.wbidpooLcom

Table of Contents .................................................... 2

W10151580A

TABLEOFCONTENTS

DRYER SAFETY .............................................................................. 2

INSTALLATION INSTRUCTIONS .................................................. 3

Tools and Parts ............................................................................ 3

Optional Pedestal ......................................................................... 4

Location Requirements ............................................................... 4

Electrical Requirements ............................................................... 6

Electrical Connection ................................................................... 8

Venting Requirements ................................................................ 13

Plan Vent System ....................................................................... 14

Install Vent System ..................................................................... 15

Install Leveling Legs ................................................................... 15

Connect Vent .............................................................................. 15

Level Dryer ................................................................................. 15

Reverse Door Swing .................................................................. 16

Complete Installation ................................................................. 17

DRYER USE .................................................................................. 18

Starting Your Dryer..................................................................... 18

Stopping or Restarting Your Dryer ............................................ 19

Lock Controls ............................................................................. 19

Drying and Cycle Tips ................................................................ 19

Status Lights ............................................................................... 19

Cycles ......................................................................................... 20

Additional Features .................................................................... 21

Changing Cycles, Options and Modifiers .................................. 21

Drying Rack Option .................................................................... 21

DRYER CARE ................................................................................ 22

Cleaning the Dryer Location ....................................................... 22

Cleaning the Lint Screen ............................................................ 22

Cleaning the Dryer Interior ......................................................... 23

Removing Accumulated Lint ...................................................... 23

Vacation and Moving Care ......................................................... 23

TROUBLESHOOTING .................................................................. 24

ASSISTANCE OR SERVICE ......................................................... 26

ACCESSORIES ............................................................................. 26

WARRANTY .................................................................................. 28

DRYERSAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the dryer, follow basic precautions,

including the following:

• Read all instructions before using the dryer.

• Do not place items exposed to cooking oils in your dryer.

Items contaminated with cooking oils may contribute to

a chemical reaction that could cause a load to catch fire.

• Do not dry articles that have been previously cleaned in,

washed in, soaked in, or spotted with gasoline, dry-

cleaning solvents, or other flammable or explosive

substances as they give off vapors that could ignite or

explode.

• Do not allow children to play on or in the dryer. Close

supervision of children is necessary when the dryer is

used near children.

• Before the dryer is removed from service or discarded,

remove the door to the drying compartment.

• Do not reach into the dryer if the drum is moving.

• Do not install or store the dryer where it will be exposed

to the weather.

• Do not tamper with controls.

• Do not repair or replace any part of the dryer or attempt

any servicing unless specifically recommended in this

Use and Care Guide or in published user-repair

instructions that you understand and have the skills to

carry out.

• Do not use fabric softeners or products to eliminate static

unless recommended by the manufacturer of the fabric

softener or product.

• Do not use heat to dry articles containing foam rubber or

similarly textured rubber-like materials.

• Clean lint screen before or after each load.

• Keep area around the exhaust opening and adjacent

surrounding areas free from the accumulation of lint, dust,

and dirt.

• The interior of the dryer and exhaust vent should be

cleaned periodically by qualified service personnel.

[] See installation instructions for grounding requirements.

SAVE THESE INSTRUCTIONS

INSTALLATIONINSTRUCTIONS

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

• Flat-blade screwdriver • Vent clamps

• #2 Phillips screwdriver • Caulking gun and

compound (for installing

• Adjustable wrench that new exhaust vent)

opens to 1" (2.5 cm) or

hex-head socket wrench • Tin snips (new vent

(for adjusting dryer feet) installations)

• Wire stripper (direct wire • 1/4"nut driver or socket

installations) wrench (recommended)

• Level • Tape measure

Parts supplied

Remove parts packages from dryer drum. Check that all parts are

included.

• Parts package.

4 Leveling legs

NOTE: Do not use leveling legs if installing the dryer on a

pedestal.

Parts needed

Check local codes. Check existing electrical supply and venting.

See "Electrical Requirements" and "Venting Requirements"

before purchasing parts.

• For close-clearance installations between 28.65" (72.77 cm)

and 34.15" (86.74 cm), see "Plan Vent System" section for

venting requirements.

I_-- s4.15"-_'1

(86.74 cm)

Mobile home installations require metal exhaust system hardware

available for purchase from the dealer from whom you purchased

your dryer. For further information, please refer to the "Assistance

or Service" section.

If using a power supply cord:

Use a UL listed power supply cord kit marked for use with

clothes dryers. The kit should contain:

• A UL listed 30-amp power supply cord, rated

120/240 volt minimum. The cord should be type SRD or

SRDT and be at least 4 ft (1.22 m) long. The wires that

connect to the dryer must end in ring terminals or spade

terminals with upturned ends.

• A UL listed strain relief.

Areyouplacingthedryeronapedestal?Youhavetheoptionof

purchasingpedestalsofdifferentheightsseparatelyforthisdryer.

Youmayselecta10"(25.4cm)pedestalora15.5"(39.4cm)

pedestalwithashelfandbindividers.Thesepedestalswilladdto

thetotalheightofthedryerforatotalheightofapproximately46"

(116.8cm)or51.5"(130.8cm),respectively.

Foragarageinstallation,youwillneedtoplacethedryeratleast

18"(46cm)abovethefloor.

Optional pedestal (15.5" [39.4 cm] model shown)

To order, call the dealer from whom you purchased your dryer or

refer to the "Assistance or Service" section.

Pedestal Color Part Number

Height

10" (25.4 cm) White WHP1000SQ

15.5" (39.4 cm) with White WHP1500SQ

shelf and bin dividers

Drying Rack

To order a drying rack, call the dealer from whom you purchased

your dryer or refer to the "Assistance or Service" section. Ask for

Part Number 8563738. For more information, see "Drying Rack

Option."

Stack Kit

Are you planning to stack your DUET SPORT TM washer and

dryer? To do so, you will need to purchase a Stack Kit.

To order, call the dealer from whom you purchased your dryer or

refer to the "Assistance or Service" section. Ask for Part Number

8572546.

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer.

Place dryer at least 18 inches (46 cm) above the floor

for a garage installation.

Failure to do so can result in death, explosion, or fire.

You will need

• A location that allows for proper exhaust installation. See

"Venting Requirements."

• A separate 30-amp circuit.

• If you are using a power cord, a grounded electrical outlet

located within 2 ft (61 cm) of either side of the dryer. See

"Electrical Requirements."

• A sturdy floor to support the total dryer weight of 127 Ibs

(57.6 kg). The combined weight of a companion appliance

should also be considered.

A level floor with a maximum slope of 1" (2.5 cm) under entire

dryer. (If slope is greater than 1" [2.5 cm], install Extended

Dryer Feet Kit, Part No. 279810.) Clothes may not tumble

properly and automatic sensor cycles may not operate

correctly if dryer is not level.

• For a garage installation, you will need to place the dryer at

least 18" (46 cm) above the floor. If using a pedestal, you will

need 18" (46 cm) to the bottom of the dryer.

Do not operate your dryer at temperatures below 45°F (7°C). At

lower temperatures, the dryer might not shut off at the end of an

automatic cycle. Drying times can be extended.

The dryer must not be installed or stored in an area where it will

be exposed to water and/or weather.

Check code requirements. Some codes limit, or do not permit,

installation of the dryer in garages, closets, mobile homes or

sleeping quarters. Contact your local building inspector.

Installation clearances

Thelocation must be large enoughto allow the dryer door to

open fully.

Dryer Dimensions

36"

(91,4 cm)

27"

(68.6 cm)

501/2"

(128.27 cm)

*Most installations require a minimum 5" (12.7 cm) clearance

behind the dryer for the exhaust vent with elbow. See "Venting

Requirements."

Installation spacing for recessed area or closet installation

The following spacing dimensions are recommended for this

dryer. This dryer has been tested for spacing of 0" (0 cm)

clearance on the sides and rear. Recommended spacing should

be considered for the following reasons:

• Additional spacing should be considered for ease of

installation and servicing.

• Additional clearances might be required for wall, door and

floor moldings.

• Additional spacing should be considered on all sides of the

dryer to reduce noise transfer.

For closet installation, with a door, minimum ventilation

openings in the top and bottom of the door are required.

Louvered doors with equivalent ventilation openings are

acceptable.

• Companion appliance spacing should also be considered.

Custom undercounter installation - Dryer only

-- 2"*

i'"1"1'''°m'

36"rein

-,ilI I1 11II

1"* _ _'_27"--•-)_ _:-- 1"*

(2.5 crn) (68 6 crn) (2.5 crn)

*Required spacing

Closet installation - Dryer only

__'_ 48 in.2.

(310 c,i,,:

24 in.2 .

(155crn2)

11"*_28.6s"--_1s"**l

{2.5crn) (72.77crn)(12.7crn)

3"*

-- (7.6 crn)

A. Side view - closet or confined area

B. Closet door with vents

*Required spacing

**For side or bottom venting, 0" (0 cm) spacing is allowed.

Recessed or closet installation - Dryer on pedestal

I olo

1,,-_tl_- 2T'--_ll_-- 1" 1".1I_-- 28.65"--)-Is"**l

(2.5 cm) (68.6 crn) {2.5 cm) {2.5 crn) {72.77 cm) (12.7 crn)

A B

A.Recessed area

B.Side view - closet or confined area

*Required spacing

**For side or bottom venting, 0" (0 cm) spacing is allowed.

Recommended installation spacing for cabinet

installation

" • T'* (17.8 cm)

cm) 5"** 28.65" 1"*

For cabinet installation, with a door, minimum ventilation

openings in the top of the cabinet are required.

1" 27" 1"

(12.7 crn) (72,77 crn) (2.5 cm) (2.5 cm)(68.6 crn) (2,8 crn)

* Required spacing

**For side or bottom venting, 0" (0 cm) spacing is allowed.

Recommended installation spacing for recessed or

closet installation, with stacked washer and dryer

The dimensions shown are for the recommended spacing.

46 in? *

{310 cm 2)

24 in. 2 *

(188crn2)

*Required spacing

5"* -_.

(12.7cm)

8"* (;.2 crn)

72"

(182.9 crn)

(2.8 cm) 88.6 cm

*Required spacing

Mobile home - additional installation requirements

This dryer is suitable for mobile home installations.

The installation must conform to the Manufactured Home

Construction and Safety Standard, Title 24 CFR, Part 3280

(formerly the Federal Standard for Mobile Home Construction

and Safety, Title 24, HUD Part 280).

Mobile home installations require:

• Metal exhaust system hardware, which is available for

purchase from your dealer.

Special provisions must be made in mobile homes to

introduce outside air into the dryer. The opening (such as a

nearby window) should be at least twice as large as the dryer

exhaust opening.

It is your responsibility

• Tocontact a qualified electrical installer.

• To be sure that the electrical connection is adequate and in

conformance with the National Electrical Code, ANSI/NFPA

70-latest edition and all local codes and ordinances.

The National Electric Code requires a 4-wire supply

connection for homes built after 1996, dryer circuits involved

in remodeling after 1996, and all mobile home installations.

A copy of the above code standards can be obtained from:

National Fire Protection Association, One Batterymarch Park,

Quincy, MA 02269.

Tosupply the required 3 or 4 wire, single phase, 120/240 volt,

60 Hz., AC only electrical supply (or 3 or 4 wire, 120/208 volt

electrical supply, if specified on the serial/rating plate) on a

separate 30-amp circuit, fused on both sides of the line. A

time-delay fuse or circuit breaker is recommended. Connect

to an individual branch circuit. Do not have a fuse in the

neutral or grounding circuit.

• Do not use an extension cord.

• If codes permit and a separate ground wire is used, it is

recommended that a qualified electrician determine that the

ground path is adequate.

Electrical Connection

To properly install your dryer, you must determine the type of

electrical connection you will be using and follow the instructions

provided for it here,

[] If local codes do not permit the connection of a neutral

ground wire to the neutral wire, see "Optional 3-wire

connection" in the "Electrical Connection" section.

This dryer is manufactured ready to install with a 3-wire

electrical supply connection. The neutral ground wire is

permanently connected to the neutral conductor (white wire)

within the dryer. Ifthe dryer is installed with a 4-wire electrical

supply connection, the neutral ground wire must be removed

from the external ground conductor screw (green screw), and

secured under the neutral terminal (center or white wire) of

the terminal block. When the neutral ground wire is secured

under the neutral terminal (center or white wire) of the

terminal block, the dryer cabinet is isolated from the neutral

conductor.

A 4-wire power supply connection must be used when the

appliance is installed in a location where grounding through

the neutral conductor is prohibited. Grounding through the

neutral is prohibited for (1) new branch-circuit installations,

(2) mobile homes, (3) recreational vehicles, and (4) areas

where local codes prohibit grounding through the neutral

conductors.

If using a power supply cord:

Use a UL listed power supply cord kit marked for use with

clothes dryers. The kit should contain:

[] A UL listed 30-amp power supply cord, rated

120/240 volt minimum. The cord should be type SRD or

SRDT and be at least 4 ft (1.22 m) long. The wires that

connect to the dryer must end in ring terminals or spade

terminals with upturned ends.

[] A UL listed strain relief.

If your outlet looks like this:

4-wire receptacle (14-30R)

Then choose a 4-wire power supply cord with ring or spade

terminals and UL listed strain relief. The 4-wire power supply

cord, at least 4 ft (1.22 m) long, must have four 10-gauge copper

wires and match a 4-wire receptacle of NEMA Type 14-30R. The

ground wire (ground conductor) may be either green or bare. The

neutral conductor must be identified by a white cover.

If your outlet looks like this:

3-wire receptacle (10-30t:?)

Then choose a 3-wire power supply cord with ring or spade

terminals and UL listed strain relief. The 3-wire power supply

cord, at least 4 ft (1.22 m) long, must have three 10-gauge copper

wires and match a 3-wire receptacle of NEMA Type 10-30R.

If connecting by direct wire:

Power supply cable must match power supply (4-wire or 3-wire)

and be:

[] Flexible armored cable or nonmetallic sheathed copper cable

(with ground wire), protected with flexible metallic conduit. All

current-carrying wires must be insulated.

[] 10-gauge solid copper wire (do not use aluminum).

[] At least 5 ft (1.52 m) long.

GROUNDING INSTRUCTIONS

[] For a grounded, cord-connected dryer:

This dryer must be grounded. In the event of malfunction or

breakdown, grounding will reduce the risk of electric shock

by providing a path of least resistance for electric current.

This dryer uses a cord having an equipment-grounding

conductor and a grounding plug. The plug must be plugged

into an appropriate outlet that is properly installed and

grounded in accordance with all local codes and ordinances.

[] For a permanently connected dryer:

This dryer must be connected to a grounded metal,

permanent wiring system, or an equipment-grounding

conductor must be run with the circuit conductors and

connected to the equipment-grounding terminal or lead on

the dryer.

WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock.

Check with a qualified electrician or service representative

or personnel if you are in doubt as to whether the dryer is

properly grounded. Do not modify the plug on the power

supply cord: if it will not fit the outlet, have a proper outlet

installed by a qualified electrician.

SAVE THESE INSTRUCTIONS

Power Supply Cord

Fire Hazard

Use a new UL listed 30 amp power supply cord.

Use a UL listed strain relief.

Disconnect power before making electrical connections.

Connect neutral wire (white or center wire) to center

terminal (silver).

Ground wire (green or bare wire) must be connected to

green ground connector.

Connect remaining 2 supply wires to remaining

2 terminals (gold).

Securely tighten all electrical connections.

Failure to do so can result in death, fire, or

electrical shock.

Direct Wire

Fire Hazard

Use 10 gauge solid copper wire.

Use a UL listed strain relief.

Disconnect power before making electrical connections.

Connect neutral wire (white or center wire) to center

terminal (silver).

Ground wire (green or bare wire) must be connected to

green ground connector.

Connect remaining 2 supply wires to remaining

2 terminals (gold).

Securely tighten all electrical connections.

Failure to do so can result in death, fire, or

electrical shock.

1. Disconnect power.

2. Remove the hold-down screw and terminal block cover.

A. Neutral ground wire

B. External ground conductor screw

C. Center, silver-colored terminal block screw

D. Terminal block cover and hold-down screw

Install strain relief.

Style 1: Power supply cord strain relief

Remove the screws from a %" (1.9 cm) UL listed strain

relief (UL marking on strain relief). Put the tabs of the two

clamp sections into the hole below the terminal block

opening so that one tab is pointing up and the other is

pointing down, and hold in place. Tighten strain relief

screws enough to hold the two clamp sections together.

;f-_- ....................................A

{

L i,. .................D

-°iV

A. Strain relief tab pointing up

B. Hole below terminal block opening

C. Clamp section

D. Strain relief tab pointing down

Put power supply cord through the strain relief. Be sure

that the wire insulation on the power supply cord is inside

the strain relief. The strain relief should have a tight fit with

the dryer cabinet and be in a horizontal position. Do not

further tighten strain relief screws at this point.

Style 2: Direct wire strain relief

Unscrew the removable conduit connector and any

screws from a %" (1.9 cm) UL listed strain relief (UL

marking on strain relief). Put the threaded section of the

strain relief through the hole below the terminal block

opening. Reaching inside the terminal block opening,

screw the removable conduit connector onto the strain

relief threads.

.......... C

A. Removable conduit connector

B. Hole below terminal block opening

C. Strain relief threads

Put direct wire cable through the strain relief. The strain

relief should have a tight fit with the dryer cabinet and be

in a horizontal position. Tighten strain relief screw against

the direct wire cable.

Now complete installation following instructions for your type

of electrical connection:

4-wire (recommended)

3-wire (if 4-wire is not available)

Electrical Connection Options

If your home has: And you will be Go to Section

connecting to:

4-wire receptacle A UL listed, 120/ 4-wire connection:

(NEMA Type 14-30R) 240-volt Power supply cord

minimum,

30-amp, dryer

power supply

cord*

4-wire direct A fused 4-wire connection:

disconnect or Direct Wire

circuit breakerbox*

(12.7 cm)

3-wire receptacle A UL listed, 120/

(NEMA type 10-30R) 240-volt

(_ minimum,

30-amp, dryer

power supply

cord*

3-wire connection:

Power supply cord

3-wire direct A fused 3-wire connection:

disconnect or Direct Wire

circuit breaker

box*

*If local codes do not permit the connection of a cabinet-ground

conductor to the neutral wire, go to "Optional 3-wire

connection" section.

4-wire connection: Power supply cord

IMPORTANT: A 4-wire connection is required for mobile homes

and where local codes do not permit the use of 3-wire

connections.

A /¸

C D E G

A. 4-wire receptacle (NEMA type 14-30R)

B. 4-prong plug

C. Ground prong

D. Neutral prong

E.Spade terminals with upturned ends

F. 3A,,(1.9 cm) UL Iisted strain relief

G. Ring terminals

1. Remove center silver-colored terminal block screw.

Remove neutral ground wire from external ground conductor

screw. Connect neutral ground wire and the neutral wire

(white or center wire) of power supply cord under center,

silver-colored terminal block screw. Tighten screw.

4-wire connection: Direct wire

IMPORTANT: A 4-wire connection is required for mobile homes

and where local codes do not permit the use of 3-wire

connections.

Direct wire cable must have 5 ft (1.52 m) of extra length so dryer

can be moved if needed.

Strip 5" (12.7 cm) of outer covering from end of cable, leaving

bare ground wire at 5" (12.7 cm). Cut 11/2'' (3.8 cm) from

3 remaining wires. Strip insulation back 1" (2.5 cm). Shape ends

of wires into a hook shape.

A. External ground conductor screw - Dotted line shows

position of NEUTRAL ground wire before being moved to

center silver-colored terminal block screw.

B. Center silver-colored terminal block screw

C. Neutral ground wire

D. Neutral wire (white or center wire)

E. 3/4,,(1.9 cm) UL listed strain relief

Connect ground wire (green or bare) of power supply cord to

external ground conductor screw. Tighten screw.

When connecting to the terminal block, place the hooked end of

the wire under the screw of the terminal block (hook facing right),

squeeze hooked end together and tighten screw, as shown.

Remove center silver-colored terminal block screw.

Remove neutral ground wire from external ground conductor

screw. Connect neutral ground wire and place the hooked

end (hook facing right) of the neutral wire (white or center

wire) of direct wire cable under the center screw of the

terminal block. Squeeze hooked ends together. Tighten

screw.

A. External ground conductor screw

B. Ground wire (green or bare) of power supply cord

C. ,_" (1.9 cm) UL listed strain relief

D. Center silver-colored terminal block screw

E.Neutral ground wire

E Neutral wire (white or center wire)

Connect the other wires to outer terminal block screws.

Tighten screws.

!! !!

5. Tighten strain relief screws.

6. Insert tab of terminal block cover into slot of dryer rear panel.

Secure cover with hold-down screw.

You have completed your electrical connection. Now go to

"Venting Requirements."

A. External ground conductor screw - Dotted line shows

position of NEUTRAL ground wire before being moved to

center silver-colored terminal block screw.

B. Center silver-colored terminal block screw

C. Neutral ground wire

D. Neutral wire (white or center wire)

E. 3/4"(1.9 cm) UL listed strain relief

Connect ground wire (green or bare) of direct wire cable to

external ground conductor screw. Tighten screw.

A. External ground conductor screw

B. Ground wire (green or bare) of power supply cable

C. 3/4"(1.9 cm) UL listed strain relief

D. Center silver-colored terminal block screw

E. Neutral ground wire

E Neutral wire (white or center wire)

4. Place the hooked ends of the other direct wire cable wires

under the outer terminal block screws (hooks facing right).

Squeeze hooked ends together. Tighten screws.

!I !!

5. Tighten strain relief screw.

6. Insert tab of terminal block cover into slot of dryer rear panel.

Secure cover with hold-down screw.

7. You have completed your electrical connection. Now go to

"Venting Requirements."

3-wire connection: Power supply cord

Use where local codes permit connecting cabinet-ground

conductor to neutral wire.

A ......

C G F

A. 3-wire receptacle (NEMA type 10-30R)

B. 3-wire plug

C. Neutral prong

D. Spade terminals with up turned ends

E, _" (1.9 cm) UL Iisted strain relief

F. Ring terminals

G. Neutral (white or center wire)

1. Loosen or remove center silver-colored terminal block screw.

2. Connect neutral wire (white or center wire) of power supply

cord to the center, silver-colored terminal screw of the

terminal block. Tighten screw.

A. External ground conductor screw

B. Neutral ground wire

C. Center silver-colored terminal block screw

D. Neutral wire (white or center wire)

E. _" (1.9 cm) UL listed strain relief

3. Connect the other wires to outer terminal block screws.

Tighten screws.

!! !!

4. Tighten strain relief screws.

5. Insert tab of terminal block cover into slot of dryer rear panel.

Secure cover with hold-down screw.

6. You have completed your electrical connection. Now go to

"Venting Requirements."

3-wire connection: Direct wire

Use where local codes permit connecting cabinet-ground

conductor to neutral wire.

Direct wire cable must have 5 ft (1.52 m) of extra length so dryer

can be moved if needed.

Strip 31/2'' (8.9 cm) of outer covering from end of cable. Strip

insulation back 1" (2.5 cm). If using 3-wire cable with ground

wire, cut bare wire even with outer covering. Shape ends of wires

into a hook shape.

When connecting to the terminal block, place the hooked end of

the wire under the screw of the terminal block (hook facing right),

squeeze hooked end together and tighten screw, as shown.

Loosen or remove center silver-colored terminal block screw.

Place the hooked end of the neutral wire (white or center wire)

of direct wire cable under the center screw of terminal block

(hook facing right). Squeeze hooked end together. Tighten

screw.

A.External ground conductor screw

B.Neutralground wire

C.Center silver-colored terminal block screw

D.Neutral wire (white or center wire)

EL_" (1.9cm) UL Iisted strain relief

Place the hooked ends of the other direct wire cable wires

under the outer terminal block screws (hooks facing right).

Squeeze hooked ends together. Tighten screws.

!! !!

4. Tighten strain relief screw.

5. Insert tab of terminal block cover into slot of dryer rear panel.

Secure cover with hold-down screw.

6. You have completed your electrical connection. Now go to

"Venting Requirements."

Optional 3-wire connection

Use for direct wire or power supply cord where local codes

do not permit connecting cabinet-ground conductor to

neutral wire.

1. Remove center silver-colored terminal block screw.

2. Remove neutral ground wire from external ground conductor

screw. Connect neutral ground wire and the neutral wire

(white or center wire) of power supply cord/cable under

center, silver-colored terminal block screw. Tighten screw.

A. External ground conductor screw

B. Center silver-colored terminal block screw

C. Neutral ground wire

D. Neutral wire (white or center wire)

EL_" (!.9 cm) UL Iisted strain relief

E Grounding path determined by a qualified electrician

Connect the other wires to outer terminal block screws.

Tighten screws.

!! !!

4. Tighten strain relief screws.

5. Connect a separate copper ground wire from the external

ground conductor screw to an adequate ground.

6. Insert tab of terminal block cover into slot of dryer rear panel.

Secure cover with hold-down screw.

Fire Hazard

Use a heavy metal vent.

Do not use a plastic vent.

Do not use a metal foil vent.

Failure to follow these instructions can result in death

or fire.

WARNING: To reduce the risk of fire, this dryer MUST BE

EXHAUSTED OUTDOORS.

IMPORTANT: Observe all governing codes and ordinances.

The dryer exhaust must not be connected into any gas vent,

chimney, wall, ceiling or a concealed space of a building.

If using an existing vent system

• Clean lint from the entire length of the system and make sure

exhaust hood is not plugged with lint.

• Replace any plastic or metal foil vent with rigid or flexible

heavy metal vent.

• Review Vent system chart. Modify existing vent system if

necessary to achieve the best drying performance.

If this is a new vent system

Vent material

• Use a heavy metal vent. Do not use plastic or metal foil vent.

• 4" (10.2 cm) heavy metal exhaust vent and clamps must be

used. DURASAFF Mventing products are recommended.

4" (10.2cm) heavymetal exhaust vent

DURASAFF Mvent products can be purchased from your

dealer or by calling Whirlpool Parts and Accessories. For

more information, see the "Assistance or Service" section.

Rigid metal vent

• For best drying performance, rigid metal vents are

recommended.

• Rigid metal vent is recommended to avoid crushing and

kinking.

Flexible metal vent

• Flexible metal vents are acceptable only if accessible for

cleaning.

• Flexible metal vent must be fully extended and supported

when the dryer is in its final location.

• Remove excess flexible metal vent to avoid sagging and

kinking that may result in reduced airflow and poor

performance.

• Do not install flexible metal vent in enclosed walls, ceilings or

floors.

Elbows

45° elbows provide better airflow than 90° elbows.

Clamps

Good Better

Use clamps to seal all joints.

Exhaust vent must not be connected or secured with screws

or other fastening devices that extend into the interior of the

duct. Do not use duct tape.

Clamp

Exhaust

Recommended hood styles are shown here.

1_4,,--_" I

(10.2 cm)

A. Louvered hood style

B.Box hood style

The angled hood style (shown here) is acceptable.

(10.2 cm)__

(6.4 cm)

• An exhaust hood should cap the vent to keep rodents and

insects from entering the home.

• Exhaust hood must be at least 12" (30.5 cm) from the ground

or any object that may be in the path of the exhaust (such as

flowers, rocks or bushes, snow line, etc.).

• Do not use an exhaust hood with a magnetic latch.

improper venting can cause moisture and lint to collect

indoors, which may result in:

[] Moisture damage to woodwork, furniture, paint, wallpaper,

carpets, etc.

[] Housecleaning problems and health problems.

Choose your exhaust installation type

A. Dryer

B. Elbow

C. Wall

D. Exhaust hood

E. Clamps

E Rigid metal or flexible metal vent

G. Vent length necessary to connect elbows

H. Exhaust outlet

Optional exhaust installations

Fire Hazard

Cover unused exhaust holes with the following kit:

279818 (white)

Contact your local dealer.

Failure to follow these instructions can result in death,

fire, electrical shock, or serious injury.

This dryer can be converted to exhaust out the right side, left

side, or through the bottom. Contact your local dealer to have the

dryer converted.

A B

A. Standard rear offset exhaust installation

B. Left or right side exhaust installation

C. Bottom exhaust installation (not an option

with pedestal installations)

Alternate installations for close clearances

Venting systems come in many varieties. Select the type best for

your installation. Two close-clearance installations are shown.

Refer to the manufacturer's instructions.

T-%;#

, _ X& _-

A B

A. Over-the-top installation (also available with one

offset elbow)

B. Periscope installation

NOTE: The following kits for close clearance alternate

installations are available for purchase. Please see the

"Assistance or Service" section to order.

• Over-the-Top Installation:

Part Number 4396028

• Periscope Installation (For use with dryer vent to wall vent

mismatch):

Part Number 4396037 - 0" (0 cm) to 18" (45.72 cm)

mismatch

Part Number 4396011 - 18" (45.72 cm) to 29" (73.66 cm)

mismatch

Part Number 4396014 - 29" (73.66 cm) to 50" (127 cm)

mismatch

Special provisions for mobile home installations

The exhaust vent must be securely fastened to a noncombustible

portion of the mobile home structure and must not terminate

beneath the mobile home. Terminate the exhaust vent outside.

Determine vent path

• Select the route that will provide the straightest and most

direct path outdoors.

• Plan the installation to use the fewest number of elbows and

turns.

• When using elbows or making turns, allow as much room as

possible.

• Bend vent gradually to avoid kinking.

• Use the fewest 90° turns possible.

Determine vent length and elbows needed for best

drying performance

• Use the following Vent system chart to determine type of vent

material and hood combinations acceptable to use.

NOTE: Do not use vent runs longer than those specified in

the Vent system chart. Exhaust systems longer than those

specified will:

• Shorten the life of the dryer.

• Reduce performance, resulting in longer drying times and

increased energy usage.

The Vent system chart provides venting requirements that will

help to achieve the best drying performance.

Vent system chart

NOTE: Side and bottom exhaust installations have a 90° turn

inside the dryer. To determine maximum exhaust length, add one

90° turn to the chart.

Number of Type of Box or Angled

90° turns vent Iouvered hoods

or elbows hoods

0 Rigid metal 64 ft (20 m) 58 ft (17.7 m)

Flexible metal 36 ft (11 m) 28 ft (8.5 m)

1 Rigid metal 54 ft (16.5 m) 48 ft (14.6 m)

Flexible metal 31 ft (9.4 m) 23 ft (7 m)

2 Rigid metal 44 ft (13.4 m) 38 ft (11.6 m)

Flexible metal 27 ft (8.2 m) 19 ft (5.8 m)

3 Rigid metal 35 ft (10.7 m) 29 ft (8.8 m)

Flexible metal 25 ft (7.6 m) 17 ft (5.2 m)

4 Rigid metal 27 ft (8.2 m) 21 ft (6.4 m)

Flexible metal 23 ft (7 m) 15 ft (4.6 m)

1. Install exhaust hood. Use caulking compound to seal exterior

wall opening around exhaust hood.

2. Connect vent to exhaust hood. Vent must fit inside exhaust

hood. Secure vent to exhaust hood with 4" (10.2 cm) clamp.

3. Run vent to dryer location. Use the straightest path possible.

See "Determine vent path" in "Plan Vent System." Avoid 90°

turns. Use clamps to seal all joints. Do not use duct tape,

screws or other fastening devices that extend into the interior

of the vent to secure vent.

Excessive Weight Hazard

Use two or more people to move and install dryer.

Failure to do so can result in back or other injury.

1. To protect the floor, use a large flat piece of cardboard from

the dryer carton. Place cardboard under the entire back edge

of the dryer.

2. Firmly grasp the body of the dryer (not the console panel).

Gently lay the dryer on the cardboard. See illustration.

Examine the leveling legs. Find the diamond marking.

Screw the legs into the leg holes by hand. Use a wrench to

finish turning the legs until the diamond marking is no longer

visible.

Place a carton corner post from dryer packaging under each

of the 2 dryer back corners. Stand the dryer up. Slide the

dryer on the corner posts until it is close to its final location.

Leave enough room to connect the exhaust vent.

1. Using a 4" (10.2 cm) clamp, connect vent to exhaust outlet in

dryer. If connecting to existing vent, make sure the vent is

clean. The dryer vent must fit over the dryer exhaust outlet

and inside the exhaust hood. Check that the vent is secured

to exhaust hood with a 4" (10.2 cm) clamp.

2. Move dryer into its final location. Do not crush or kink vent.

3. (On gas models) Check that there are no kinks in the flexible

gas line.

4. Once the exhaust vent connection is made, remove the

corner posts and cardboard.

Check the levelness of the dryer. Check levelness first side to

side, then front to back.

If the dryer is not level, prop up the dryer using a wood block.

Use a wrench to adjust the legs up or down and check again for

levelness.

You can change your door swing from a right-side opening to a

left-side opening, if desired.

1. Place a towel or soft cloth on top of the dryer or work space

to protect the surface.

Remove the door assembly

1. Remove the 4 screws that hold the door hinge on the front

panel of the dryer.

A. Dryer front panel

B. Door assembly

Lay the door assembly on a flat, protected surface with the

inside (inner door assembly) facing up.

Remove the 6 Phillips head screws to release the outer door

assembly from the inner door assembly, as indicated below.

See illustration. It is important that you remove only the

6 indicated screws.

4. Lift the inner door assembly off the outer door assembly.

5. Disengage locking tabs by rotating inner ring clockwise. See

illustration.

Reverse hinge

1. Use a small flat-blade screwdriver to remove 2 plug strips

from the inner door. Slide the head of the screwdriver under

the plugs, being certain not to scratch the inner door surface.

Lift up.

Remove hinge cover.

A ...................(__

A. Door hinge

B. Plug strips

C. Hinge cover

Remove the 4 screws that attach to the inner door hinge and

move the hinge to the other side. Reinstall the 4 screws.

A. Door hinge

4. Reinstall plug strips on opposite side of the inner door.

5. Check for fingerprints on the glass. Clean glass if necessary.

6. Place the inner door assembly inside the outer door

assembly. To fit correctly, the inner door assembly edge fits

completely inside the outer door assembly edge.

A. Inner ring

B. Outer ring

6. Turn inner ring 180 ° and lock tabs into place.

7. Reassemble the inner and outer door assemblies with the

6 screws.

Reverse the strike

1. Use a small flat-blade screwdriver to remove plug strip from

the dryer door opening. Slide the head of the screwdriver

under the plugs, being certain not to scratch the dryer

surface. Lift up.

2. Remove the strike.

3. Insert strike and plug strip on the opposite side.

A.Plug strip (cannot be seenfrom this angle)

B. Door strike

Reinstall the door

1. Reattach door to dryer front panel with the 4 screws.

1. Check that all parts are now installed. If there is an extra part,

go back through the steps to see which step was skipped.

2. Check that you have all of your tools.

3. Dispose of/recycle all packaging materials.

4. Check the dryer's final location. Be sure the vent is not

crushed or kinked.

5. Check that the dryer is level. See "Level Dryer."

6. For power supply cord installation, plug into an outlet. For

direct wire installation, reconnect power.

7. Remove the blue protective film on the console and any tape

remaining on the dryer.

8. Read "Dryer Use."

9. Wipe the dryer drum interior thoroughly with a damp cloth to

remove any dust.

10. Select a Timed Dry heated cycle, and start the dryer. Do not

select the Air Only modifier.

If the dryer will not start, check the following:

• Controls are set in a running or "On" position.

• Start button has been pushed firmly.

• Dryer is plugged into an outlet and/or electrical supply

is connected.

• Household fuse is intact and tight, or circuit breaker has

not tripped.

• Dryer door is closed.

11. When the dryer has been running for 5 minutes, open the

dryer door and feel for heat. If you feel heat, cancel cycle and

close the door.

If you do not feel heat, turn off the dryer and check the

following:

• There may be 2 household fuses or circuit breakers for

the dryer. Check that both fuses are intact and tight, or

that both circuit breakers have not tripped. If there is still

no heat, contact a qualified technician.

NOTE: You may notice a burning odor when the dryer is first

heated. This odor is common when the heating element is first

used. The odor will go away.

A. Dryer front panel

B. Door assembly

2. Check for fingerprints on the glass. Clean the glass if

necessary.

3. Close door and check that it latches securely.

DRYERUSE

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer.

Do not dry anything that has ever had anything

flammable on it (even after washing).

Failure to follow these instructions can result in death,

explosion, or fire.

Fire Hazard

No washer can completely remove oil.

Do not dry anything that has ever had any type of oil on

it (including cooking oils).

Items containing foam, rubber, or plastic must be dried

on a clothesline or by using an Air Cycle.

Failure to follow these instructions can result in death

or fire.

WARNING: To reduce the risk of fire, electric shock, or injury to

persons, read the IMPORTANT SAFETY INSTRUCTIONS before

operating this appliance.

Follow these basic steps to start your dryer. Please refer to

specific sections of this manual for more detailed information.

f. Clean lint screen before each load. See "Cleaning the Lint

Screen."

2. Place laundry into dryer and shut door.

3. Press POWER.

Point the dial to an Auto or Manual Cycle. The preset settings

for Auto or Manual Cycles will illuminate. The estimated (auto

cycle) or actual (manual) cycle time (in minutes) will show in

the display.

NOTE: A preset time is displayed when an automatic cycle is

selected. During the first few minutes of the drying process,

the cycle time may automatically vary from the preset time

based on the size and fabric type of the load. Toward the end

of the drying process, the estimated time display will adjust

again, showing the final drying time.

To use an Auto Cycle

• Select DRYNESS to adjust how dry you want the load.

The time displayed is an estimated length of the cycle

based on the Dryness selected. As the cycle runs, the

control senses the dryness of the load and adjusts the

time automatically for the selected dryness level.

NOTE: Time is not adjustable for Automatic Cycles. Pressing

the Timing Up or Down buttons will cause a triple beep,

indicating that the time cannot be changed.

To make changes to the Dryness and/or Options during

an Auto Cycle:

• Press PAUSE/CANCEL once.

Adjust Dryness and/or Options.

NOTE: Dryness level selections can be made only while

using Auto Cycles. Selecting More Dry, Normal or Less

Dry automatically adjusts the sensed time needed.

MOREDRY

NORMAL

• Select an Auto Cycle. Auto cycles will default to the last

dryness setting used for that cycle.

DRYNESS

AutoCycles

Auto Dry cycles take the guesswork out of drying time

and enhance fabric care. The amount of time that is

displayed is the estimated time remaining in the cycle.

To use a Manual Cycle

• Point the dial to a Manual Cycle.

• Press TIMING Up or Down until the desired drying time is

displayed. Tap TIMING Up or Down, and the time will

change by 1-minute intervals. Press and hold TIMING Up

or Down, and the time will change by 5-minute intervals.

NOTE: The Timing feature can be used only with Manual

Cycles.

@®

rIMING

• Press TEMP ADJUST until the desired temperature

illuminates.

To make changes to Time, Temperature, WRINKLE

SHIELD TM feature and Cycle Signal during a Manual

Cycle:

• Press PAUSE/CANCEL once.

• Adjust theTime, Temperature, WRINKLE SHIELD TM

feature and End of Cycle Signal.

(OPTIONAL STEP) If desired, select WRINKLE SHIELD TM

feature. For more details, see "WRINKLE SHIELD TM Feature"

in "Additional Features."

(OPTIONAL STEP) The Cycle Signal is preset to ON. If

desired, you may turn the Cycle Signal OFR

Press and hold START for approximately 1 second until dryer

starts. Be sure the door is closed.

• If you do not press Start within 5 minutes of selecting a

cycle, the dryer automatically shuts off.

To pause/stop the dryer at any time

Open the door or press PAUSE/CANCEL once.

To restart the dryer

Close the door. Press and hold START until dryer starts.

To cancel your dryer at any time

Press PAUSE/CANCEL twice.

NOTE: Drying will continue from where the cycle was interrupted

if you close the door and press Start within 5 minutes. Ifthe cycle

is interrupted for more than 5 minutes, the dryer will shut off.

Select new cycle settings before restarting the dryer.

This feature allows you to lock your settings to avoid unintended

use of the dryer. You can also use the control lock feature to

avoid unintended cycle or option changes during dryer operation.

To enable the control lock feature:

Press and hold END OF CYCLE SIGNAL button for 3 seconds.

The Lock/Unlock Control icon lights up, and a single beep tone is

heard. To unlock, press and hold END OF CYCLE SIGNAL button

for 3 seconds. The indicator light turns off.

Select the correct cycle and dryness level or temperature for your

load. If an Auto Cycle is running, the display shows the estimated

cycle time when your dryer is automatically sensing the dryness

level of your load. If a Manual Cycle is running, the display shows

the exact number of minutes remaining in the cycle.

Cool Down tumbles the load without heat during the last few

minutes of all cycles. Cool Down makes the loads easier to

handle and reduces wrinkling. The length of the Cool Down

depends on the load size and dryness level.

Drying tips

• Follow care label directions when they are available.

• If desired, add a fabric softener sheet. Follow package

instructions.

• Remove the load from the dryer as soon as tumbling stops to

reduce wrinkling. This is especially important for permanent

press, knits and synthetic fabrics.

• Avoid drying heavy work clothes with lighter fabrics. This

could cause overdrying of lighter fabrics, leading to increased

shrinkage or wrinkling.

Cycle tips

• Dry most loads using the preset cycle settings.

• Refer to the Auto or Manual Preset Cycle Settings chart (in

the "Cycles" section) for a guide to drying various loads.

Drying temperature and Dryness are preset when you

choose an Auto Cycle. You can choose a different

dryness level, depending on your load by pressing the

DRYNESS button to select MORE DRY or LESS DRY.

• If you wish to adjust the cycle length of a Manual Cycle,

you must press TIMING Up or Down. Adjust the

temperature of a Manual Cycle by pressing TEMP

ADJUST until the desired temperature is selected.

NOTE: You cannot choose a Dryness Level with Manual

Cycles.

You may follow the progress of your dryer with the drying Status

indicator lights.

SENSING/

WET_/

DAMP:/

COOLDOWN

CYCLECOMPLETE;i_

WRINKLESHIELD

Sensing

When a cycle is first turned on, the SENSING light illuminates

until a wet item is detected.

• In an Auto Cycle, if a wet item has not been detected within

5 minutes, the Sensing light will turn off.

• In a Manual Cycle, if a wet item is not detected within

5 minutes, the Sensing light will turn off and the Damp light

will turn on.

Wet

The WET light will turn on when a wet item has been detected in

the dryer. The Wet light will remain on until:

• The damp dry point is reached in an Auto or Manual Cycle.

Damp

The DAMP light indicates that the load has reached the damp dry

level.

Cool Down

The COOL DOWN light illuminates during the cool down part of

the cycle. Laundry is cooling down for ease in handling.

Cycle Complete

This light illuminates when a drying cycle is finished. Ifthe

WRINKLE SHIELD TM feature has been selected, the WRINKLE

SHIELD TM feature indicator light will also be illuminated.

The Cycle Complete light turns off 1hour after the end of a drying

cycle (including the WRINKLE SHIELD TM cycle of 90 minutes),

when Pause/Cancel is pressed, or when the door is opened.

WRINKLE SHIELD TM Feature

The WRINKLE SHIELD TM feature light illuminates when this

option is selected. This indicator stays on with the Cycle

Complete light.

Indicator lights

Other indicator lights on the control panel show when Cycle,

Temp Adjust, and End of Cycle settings are selected.

Select the drying cycle that matches the type of load you are

drying. See Auto Preset or Manual Preset Cycle Settings charts.

c/_u

DELICATE

SUPER/ _ __TOUCH

DEUCAT /

DAMP_ \\ _\ _ QUICK

0R, \\ D,Y

_TIMED

\ _ ,DRY

AUTO MANUAL

Cycle control knob

Auto Cycles

Auto Cycles allow you to match the cycle to the load you are

drying. See the following Auto Preset Cycle Settings chart. Each

cycle dries certain fabrics at the recommended temperature. A

sensor detects the moisture in the load and automatically adjusts

the drying time for optimal drying.

Heavy Duty

Use this cycle to get High heat for heavyweight mixed loads,

cotton towels or jeans.

Normal

Use this cycle to get Medium heat for drying mixed loads and

sturdy fabrics such as work clothes.

Casual

Use this cycle to get Low heat for drying no-iron fabrics such as

sport shirts, casual business clothes and permanent press

blends.

Delicate

Use this cycle to get Low heat for drying synthetic fabrics,

washable knit fabrics and no-iron finishes.

Super Delicate

Use this cycle to get Extra Low heat to gently dry items such as

lingerie, exercise wear or sheer curtains.

Damp Dry

Use this cycle to dry items to a damp level using Low heat, or to

dry items that do not require an entire drying cycle. Damp dry

items such as jeans (to avoid stiffness) or cotton clothing (to

make ironing easier). The temperature setting on this cycle

cannot be adjusted. Items will have different levels of dampness.

At the end of this cycle, clothes will be damp.

Auto Preset Cycle Settings

Auto Cycles Temp. Time*

Load Type (Minutes)

HEAVY DUTY High 40

Heavyweight mixed loads,

cotton towels, jeans

NORMAL Medium 35

Mixed loads, corduroys, work

clothes, sheets

CASUAL Low 35

Permanent press, synthetics

DELICATE Low 30

Lightweight items, blouses,

synthetics

SUPER DELICATE Extra Low 25

Lingerie

DAMP DRY Low 20

Clothes to come out suitable

for ironing

*Estimated Time with Auto DRYNESS (Normal) setting.

Time will vary depending on load type and load size.

Manual Cycles

Use Manual Cycles to select a specific amount of drying time and

a drying temperature. When a Manual Cycle is selected, the

ESTIMATED TIME REMAINING display shows the actual time

remaining in your cycle. You can change the actual time in the

cycle by pressing TIMING Up or Down.

Timed Dry

Use this cycle to complete drying if items are still damp after an

Auto Cycle. Timed Dry is also useful for drying heavyweight and

bulky items such as bedspreads and work clothes.

Quick Dry

Use this cycle for drying small loads or loads that need a short

drying time.

Touch Up

Use this setting to help smooth out wrinkles from such items as

clothes packed in a suitcase or items wrinkled from being left in

the dryer too long.

Manual Preset Cycle Settings

Manual Cycles Temp. Default Time

Load Type (Minutes)

TIMED DRY High* 40

Heavyweight, bulky items,

bedspreads, work clothes

QUICK DRY Medium 27

Small loads

TOUCH UP Medium 20

Helps smooth out wrinkles

*The Timed Dry cycle will default to the last temperature used for

Timed Dry.

Page is loading ...

Whirlpool WED8300SB2 Owner's manual

Brand: Whirlpool

Model: WED8300SB2

Category: Electric laundry dryers

Type: Owner's manual

This manual is also suitable for

Download PDF

report

Whirlpool WED8300SB2 Owner's manual

This manual is also suitable for

Whirlpool WED8300SB2 Owner's manual

Related papers

Other documents