Etec A707DXI Operating Instructions Manual

Etec
Brand
Etec
Model
A707DXI
Category
CD players
Type
Operating Instructions Manual
CAUTION: GROUNDING OR POLARIZATION. THE PRECAUTIONS SHOULD BE
TAKEN SO THAT THE WIDER BLADE OF THE AC PLUG MUST MATCH THE SLOT
IN RECEPTACLE "WALL SOCKET".
WARNING: To reduce
the risk of electric shock, do
not remove cover (or back).
No user-serviceable
parts inside. Refer
servicing to qualified
service personnel.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The exclamation
point within the
triangle is a warning
sign alerting you of
important instructions
accompanying the
product.
The lightning flash
and arrowhead
within the triangle
is a warning
sign alerting you of
"dangerous voltage"
inside the product.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPLIANCE TO DRIPPING OR SPLASHING LIQUIDS.
E-2
CAUTION: INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS DEFEATED.
AVOID EXPOSURE TO BEAM.
VORSICHT: UNSICHTBARE LASERSTRAHLUNG TRITT AUS, WENN DECKEL
GEÖFFNET UND WENN SICHERHITSVERRIEGELUNG ÜBERBRÜCKT IST.
NICHT DEM STRAHL AUSSETZEN.
VARNING: OSYNLIG LASERSTRÁLNING NÄR DENNA DEL ÄR ÖPPNAD OCH SPÄRR
ÄR URKOPPLAND. STRÁLEN ÄR FARLIG.
ADVARSEL: USYNLIG LASERSTRÁLING VED ÁBNING. NÁR
SIKKERHEDSAFBRYDERE ER UDE AF FUNKTION. UNDGÁ UDS/ETTELSE FOR
STRÁLING.
ATTENZIONE: RADIONS LASER INVISIDILE. NON GUARDARE DIRETTAMENTE
NELLA SORGENTE DEL LASER.
ACHTUNG: LASERLINSE NICHT BERÜHREN UNSICHTBARER LASERSTRAHL.
AVISO: A LENTE NUNCA DEVE SER TOCADA.
CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
LASER DE CLASSE
LASER DI PRIMA CLASSE
KLASSE 1 LASER
LASER PRIMERA CLASE
LASER CLASSE 1
KLASSE 1 LASER PRODUKT
CAUTION
DO NOT EXPOSE TO DRIPPING OR SPLASHING LIQUIDS!
CAUTION : TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF
PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE
LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE
CORRESPONDANTE DE LA PRISES ET POUSSER JUSQU' AU FOND.
OPERATING INSTRUCTIONS
MODEL : A707DXI
S-BASS
SUPER BASS
BOOSTER
REMOTE
CONTROL
CLOCK
QUARTZ
DIGITAL
HIGH OUTPUT MICRO SHELF SYSTEM
DIGITAL CD-RADIO-CLOCK HI-FI
WITH WALL MOUNTING CAPABILITY
DATE : 5 FEB, 2007
MODEL A707DXI “eTEC”
REVISED ENGLISH I/M FOR APPROVAL
SIZE : 102 (W) X 136 (H) MM FOR EACH PAGE
PRINTING COLOR : BLACK
BLUE
BACKLIGHT
DISPLAY
DX
DIGITAL
DISPLAY
E-3 E-4
1. READ INSTRUCTIONS - All the safety and operating instruction should be read before the product
is operated.
2. RETAIN INSTRUCTIONS - The safety and operating instruction should be retained for future
reference.
3. HEED WARNINGS - All warning on the product and in the operating instructions should be adhered to.
4. FOLLOW INSTRUCTIONS - All operating and use instructions should be followed.
5. CLEANING - Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or
aerosol cleaners. Use a damp cloth for cleaning.
6. ATTACHMENTS - Do not use attachments not recommended by the product manufacturer as they
may cause hazards.
7. WATER AND MOISTURE - Do not use this product near water- for example, near a bath tub,
wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, and the like.
8. ACCESSORIES - Do not place this product on an unstable cart, stand, tripod, bracket, or table.
The product may fall, causing serious injury to a child or adult, and serious damage to the product.
Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with
the product. Any mounting of the product should follow the manufacturer's instructions, and should
use a mounting accessory recommended by the manufacturer.
9. A product and cart combination should be moved with care. Quick stops,
excessive force, and uneven surfaces may causethe appliance and cart
combination to overturn.
10. VENTILATION - Slots and openings in the cabinet are provided for ventilation
and to ensure reliable operation of the product and to protect it from
overheating, and these openings must not be blocked or covered. The openings should never be
blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should
not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is
provided or the manufacturer's instruction have been adhered to.
11. POWER SOURCES - This product should be operated only from the type of power source indicated
on the marking label. If you are not sure of the type of power supply to your home, consult your
product dealer or local power company. For products intended to operate from battery power, or
other sources, refer to the operating instruction.
12. GROUNDING OR POLARIZATION - This product may be equipped with a polarized
alternating-current line plug (a plug having one blade wider than the other). This plug will fit into the
power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the
outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your
obsolete outlet. Do not defeat the safety purpose of the polarizes plug.
ALTERNATE WARNINGS - This product is equipped with a three-wire grounding-type plug, a plug
having a third (grounding) pin. This plug will only fit into a grounding-type power outlet.
This is a safety feature. If you are unable to insert the plug into the outlet, contact you electrician to
replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug.
13. POWER-CORD PROTECTION - Power supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them, paying particular attention to cords
at plugs, convenience receptacles, and point where they exit from the product.
SEE FIGURE:
NEC - NATIONAL ELECTRICAL CODE
GROUND
CLAMP
ANTENNA
LEAD IN WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
ELECTRIC
SERVICE
EQUIPMENT
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
IMPORTANT SAFETY INSTRUCTIONS
14. PROTECTIVE ATTACHMENT PLUG - The product is equipped with an attachment plug having
overload protection. This is a safety feature. See Instruction Manual for replacement or resetting
of protective device. If replacement of the plug is required, be sure the service technician has used
a replacement plug specified by the manufacturer that has the same overload protection as the
original plug.
15. OUTDOOR ANTENNA GROUNDING - If an outside antenna is connected to the receiver, be sure
the antenna system is grounded so as to provide some protection against voltage surges and
built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides
information with regard to proper grounding of the mast and supporting structure, grounding of the
mast and supporting structure, grounding of the lead-in wire to an antenna-discharge unit, size of
grounding conductors, location of antenna-discharge unit, connection to grounding electrodes,
and requirements for the grounding electrode.
16. LIGHTNING - For added protection for this product during a lightning storm, or when it is left
unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the
antenna or cable system. This will prevent damage to the product due to lightning and power-line
surges.
17. POWER LINES - An outside antenna system should not be located in the vicinity of overhead
power lines or other electric light or power circuits, or where it can fall into such power lines or
circuits. When installing an outside antenna system, extreme care should be taken to keep from
touching such power lines or circuits as contact with them might be fatal.
18. OVERLOADING - Do not overload wall outlets, extension cords, or integral convenience
receptacles as this can result in a risk of fire or electric shock.
19. OBJECT AND LIQUID ENTRY - Never push objects of any kind into this product through openings
as they may touch dangerous voltage points or short-out parts that could result in a fire or electric
shock. Never spill liquid of any kind on the product.
20. SERVICING - Do not attempt to service this product yourself as opening or removing covers may
expose you to dangerous voltage or other hazards, Refer all servicing to qualified service personnel.
21. DAMAGE REQUIRING SERVICE - Unplug this product from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
a) When the power-supply cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally be following the operating instructions. Adjust only
those controls that are covered by the operating instructions as an improper adjustment of
other controls may result in damage and will often require extensive work by a qualified
technician to damage and will often require extensive work by a qualified technician to restore
the product to its normal operation.
e) If the product has been dropped or damaged in any way, and
f ) When the product exhibits a distinct change in performance -
this indicates a need for service.
22. REPLACEMENT PARTS - When replacement parts are required, be sure the service technician
has used replacement parts specified by the manufacturer or have the same characteristics as the
original part. Unauthorized substitutions may result in fire, electric shock, or other hazards,
23. SAFETY CHECK - Upon completion of any service or repairs to this product, ask the service
technician to perform safety checks to determine that the product is in proper operating condition.
24. WALL OR CEILING MOUNTING - The product should be mounted to a wall or ceiling only as
recommended by the manufacturer.
25. HEAT - The product should be situated away from heat sources such as radiators, heat registers,
stoves, or other products (including amplifiers) that produce heat.
INSERTION & REMOVAL OF DISCS
- THE SET MUST BE SWITCHED "ON" WHEN OPENING OR CLOSING THE CD-DOOR.
PRESS THE DOOR "OPEN/CLOSE" BUTTON ONCE TO OPEN (OR CLOSE) THE DOOR.
- PLACE A CD INTO THE COMPARTMENT WITH THE LABEL-SIDE (PRINTED SIDE OF DISC)
FACING OUTWARDS (TOWARDS YOU).
- WHEN THE CD HAS LOCKED ONTO THE CENTER SPINDLE,
PRESS THE DOOR "OPEN/CLOSE" BUTTON TO CLOSE THE CD DOOR.
- THE CD IS NOW READY TO BE PLAYED.
- TO REMOVE A DISC, FOLLOW THE SAME PROCEDURE AS DESCRIBED ABOVE, EXCEPT
TO REMOVE THE CD INSTEAD OF INSERTING IT INTO THE COMPARTMENT.
- IMPORTANT : ALWAYS HOLD A CD BY IT'S EDGES. AVOID GETTING ANY FINGER-PRINTS,
SMUDGES OR DIRT ONTO THE SURFACE OF A DISC. IN CASE THIS HAPPENS, USE A
SPECIAL CD-CLEANING CLOTH OR CLEANING KIT TO REMOVE THE DIRT OR SMUDGES.
E-6
POWER SUPPLY
- THIS SET WORKS ON NORMAL HOUSEHOLD AC-POWER.
- MAKE SURE THE SET VOLTAGE OF THE UNIT MATCHES YOUR LOCAL VOLTAGE.
- INSERT THE PLUG OF THE AC-CORD INTO A WALL OUTLET WITH AC-POWER.
- PRESS THE “POWER” ON/ OFF KNOB TO SWITCH “ON” THE UNIT.
WHEN THE POWER IS “ON” THE ENTIRE DIGITAL DISPLAY WILL BE LIT UP WITH
A “BLUE” BACK-LIGHT. THIS INDICATES THE HI-FI IS SWITCHED “ON”.
IMPORTANT : HOW TO TELL IF POWER IS "ON" ?
- SET THE FUNCTION SWITCH TO "RADIO".
- SET THE RADIO BAND SELECTOR SWITCH TO THE DESIRED BAND.
- ROTATE TUNING KNOB TO TUNE-IN THE DESIRED STATION, AS DISPLAYED IN THE LCD
DIGITAL DISPLAY.
- ADJUST THE VOLUME TO THE DESIRED LEVEL. (UP/ DOWN)
- TO IMPROVE FM-RADIO RECEPTION, FULLY EXTEND THE FM-ANTENNA WIRE AND
ADJUST IT'S POSITION.
- TO IMPROVE AM (MW) RADIO RECEPTION, ROTATE OR RE-POSITION THE MAIN UNIT.
OPERATION OF RADIO
THE BUILT IN "SUPER BASS BOOSTER" CIRCUIT PROVIDES A POWERFUL
ENHANCEMENT TO LOW FREQUENCY MUSIC, GIVING A STRONGER BASS
SOUND WHICH IS IDEAL FOR "ROCK" OR "JAZZ" MUSIC.
- THIS SET HAS A BUILT-IN DIGITAL CLOCK, WHICH IS DISPLAYED WHEN THE UNIT IS IN
"CD" MODE OR WHEN THE UNIT IS SWITCHED "OFF" (WITH AC-POWER SUPPLY
CONNECTED).
- TO SET THE CORRECT TIME, PRESS AND HOLD THE "TIME SET SWITCH" AND PRESS
THE "MINUTE" AND "HOUR" ADJUST SWITCHES TO ADVANCE TO THE CORRECT TIME.
SUPER BASS FUNCTION
CLOCK FUNCTION - HOW TO SET CORRECT TIME
LOCATION OF CONTROLS
1. CD/ CLOCK/ RADIO DIGITAL
DISPLAY
2. FM STEREO LED LIGHT
3. DBBS LED LIGHT
4. REMOTE CONTROL SENSOR
5. SPEAKER-OUT SOCKETS
(LEFT & RIGHT)
6. HEADPHONE JACK
7. FM-ANTENNA WIRE
8. STAND (FOR UNIT)
9. AC-CORD & PLUG
10. POWER ON/ OFF SWITCH
11. TIME SET KNOB
12. FUNCTION SWITCH (RADIO/ CD)
13. CLOCK ADJUST “HOUR” KNOB
12
13
14
15 16
17
18
1920
2122
23
24
25
26
11
10
1
89
2728
E-5
14. BAND SWITCH
(FM STEREO/ FM/ AM)
15. CLOCK ADJUST “MINUTE” KNOB
16. RADIO TUNING KNOB
17. CD “PROGRAM” KNOB
18. CD DOOR OPEN/CLOSE KNOB
19. CD “STOP” KNOB
20. CD “PLAY/ PAUSE” KNOB
21. CD “NEXT” KNOB
22. CD “BACK” KNOB
23. CD “REPEAT” KNOB
24. DBBS KNOB
25. VOLUME DOWN KNOB
26. VOLUME UP KNOB
27. SPEAKER (LEFT & RIGHT)
28. STAND (FOR SPEAKER)
18
24
20
19
26
25
10
22
21
2
3
4
5
67
2728
E-8
SPECIFICATIONS
AC-POWER SUPPLY : ...................................... AC 120V , 60 Hz
AC-POWER CONSUMPTION : .......................... 30W
SPEAKER : ......................................................... 4” x 2 WOOFER + 2” X 2 TWEETER
SPEAKER CAPACITY POWER : .........................10W X 2 (4 Ohm)
AMPLIFIER MAXIMUM POWER : ....................... 10 W
TUNER- FREQUENCY : ..................................... AM 530 - 1710 k Hz
FM 88 - 108 MHz
~
THE APPARATUS SHOULD NOT BE EXPOSED TO DRIPPING OR SPLASHING
AND NO OBJECTS FILLED WITH LIQUIDS SHOULD BE PLACED ON THE
APPARATUS.
- THE DISPLAY WILL NOW INDICATE THE EXACT SONG SEQUENCE IN MEMORY
BY DISPLAYING ALL THE SONG NUMBERS RAPIDLY.
- ALSO, THE SYMBOL WILL REMAIN "ON" TO INDICATE THAT YOU
HAVE SAVED A PROGRAM-MEMORY (SEQUENCE).
- PRESSING PLAY WILL NOW PLAY BACK THE "SAVED SEQUENCE" IN
THE PROGRAM MEMORY.
- PRESSING NEXT/ BLACK WILL MOVE TO THE NEXT OR PREVIOUS SONG
IN THE SAVED SEQUENCE.
- TO CLEAR (CANCEL) THE ENTIRE PROGRAM WHICH IS STORED IN THE MEMORY,
SIMPLY PRESS "STOP" TWICE, OR SWITCH "OFF" THE SET.
Prog
E-7
NORMAL CD OPERATION
- INSERT A CD AS DESCRIBED. SET THE FUNCTION SWITCH TO "CD".
- ONCE THE CD-DOOR IS CLOSED (WITH A DISC INSIDE) THE SET WILL IMMEDIATELY
READ THE DISC AND DISPLAY THE NUMBER OF SONGS (TRACKS) ON THE CD.
- PRESS THE PLAY/PAUSE SWITCH . THE DISK WILL START SPINNING AND THE
FIRST SONG (TRACK) WILL START PLAYING. THE DISPLAY WILL INDICATE THE
CURRENT TRACK NUMBER. ("1" IF IT IS THE FIRST TRACK).
- AT ANYTIME DURING PLAYBACK, PRESS THE "STOP" SWITCH TO STOP
OPERATION OF THE SET. THIS WILL RESET THE SET TO THE FIRST TRACK (IF YOU
PRESS PLAY AFTER STOP, THE FIRST TRACK WILL ALWAYS START PLAYING). HOWEVER,
THE DIGITAL DISPLAY WILL SHOW THE TOTAL NUMBER OF TRACKS ON THE DISC.
- AT ANYTIME DURING PLAYBACK, "PRESS AND RELEASE" THE SEEK/SCAN SWITCHES :
"BACK" OR "NEXT" TO SKIP BACKWARDS OR FORWARDS BY ONE TRACK, AS DESIRED.
- AT ANYTIME DURING PLAYBACK, "PRESS AND HOLD" THE SEEK/SCAN SWITCHES :
"BACK" OR "NEXT" TO FAST-REVERSE OR FAST-FORWARD THE SPECIFIC TRACK,
WHICH IS CURRENTLY PLAYING.
- AT ANYTIME DURING PLAYBACK, PRESS THE "CD REPEAT SWITCH" AS FOLLOWS:
PRESS ONCE = TO REPEAT THE CURRENT TRACK (REPEAT SYMBOL WILL "FLASH")
PRESS TWICE = TO REPEAT ALL TRACKS (FULL CD) (REPEAT SYMBOL WILL STAY "ON")
- TO PAUSE PLAY BACK AT ANYTIME DURING PLAYBACK, PRESS THE "PLAY/PAUSE"
SWITCH . PRESS PLAY/PAUSE SWITCH TO RESUME OPERATION AT THE
SAME TRACK AND POSITION.
P
PROGRAMMING THE CD-PLAYER
- THE CD PLAYER CAN BE PROGRAMMED TO PLAY ANY SEQUENCE OF UPTO
20 TRACKS, AS DESIRED.
- ALWAYS PRESS THE STOP SWITCH BEFORE STARTING THE PROGRAMMING.
- PRESS THE PROGRAM SWITCH ,THE DISPLAY WILL SHOW A FLASHING
SYMBOL AND THE DISPLAY WILL SHOW “ ” (FLASHING), TO INDICATE
THAT THE SET IS NOW IN "MEMORY PROGRAMMING MODE", AT MEMORY
POSITION NO. 1.
- REPEAT THE PREVIOUS 2 STEPS, EACH TIME SELECTING ANY TRACK NUMBER
OF YOUR CHOICE TO BE STORED IN THE SUCCESSIVE MEMORY (PROGRAM)
POSITIONS.
- WHEN YOU PRESS THE DISPLAY WILL ADVANCE TO THE NEXT MEMORY
POSITION NUMBER (EG. “ ” FOR 2ND POSITION).
- PRESS THE NEXT/BACK SWITCHES TO SELECT THE TRACK (SONG)
NUMBER YOU WISH TO BE STORED IN THE FIRST MEMORY (PROGRAM)
POSITION, AND PRESS (PROGRAM) TO CONFIRM YOUR SELECTION.
P
P
- AFTER EACH TRACK NUMBER, REMEMBER TO PRESS THE PROGRAM SWITCH .
- AFTER A MAXIMUM OF 20 SONGS (OR LESS) HAVE BEEN SELECTED AS
DESCRIBED ABOVE, PRESS THE SWITCH.
P
Prog
0 1
0 2
P
SYSTEM SET UP PROCEDURE
A. AS A "SHELF SYSTEM" (TABLE TOP USE)
- INCLUDED 1 PC BASE FOR THE MAIN UNIT ( )
FIXING THE BASE TO THE MAIN UNIT:
1. PLACE THE BASE UNDER THE MAIN UNIT,
2. SLIDE THE BASE FROM RIGHT TO LEFT (SEE DIAGRAM BELOW).
3. STOP WHEN ARROWS ARE ALIGNED (SEE DIAGRAM). THE BASE IS NOW LOCKED
TO MAIN UNIT.
(TO RELEASE THE BASE FROM THE MAIN UNIT, SLIDE THE BASE FROM RIGHT TO LEFT
(OPPOSITE DIRECTION) UNTIL IT BECOMES RELEASED.
- INCLUDED 2 PCS BASE FOR THE SPEAKERS ( )
FIXING THE BASE TO THE SPEAKER BOX (LEFT/ RIGHT):
1. PLACE THE BASE UNDER THE SPEAKER,
2. SLIDE THE BASE FORWARD UNTIL YOU HEAR A "CLICK" SOUND,
THEN THE BASE WILL LOCKED. (TO RELEASE THE BASE FROM THE SPEAKER,
LIFT THE LATCH AT THE REAR OF THE BOTTOM OF THE SPEAKER BOX AND
PUSH FORWARD, THEN THE BASE WILL BE UNLOCKED).
"CLICK"
1. 2. 3.
3.
LOCKED WHEN
ARROWS ALIGN
1. 2.
SLIDE UNTIL LOCKED
(ARROWS ALIGNED)
LOWER THE
SPEAKER BOX
ONTO THE BASE
SLIDE THE BASE
FORWARD UNTIL
IT LOCKS
WHEN THESE
ARROWS ARE ALIGNED
THE BASE IS PROPERLY
INSTALLED ONTO MAIN UNIT
110 MM
(8.1")
WALL MOUNT
SCREW GUIDE
WALL MOUNT
SCREW GUIDE
B. AS A "WALL MOUNT SYSTEM"
CONNECTION OF SPEAKER BOXES
- PLACE THE SPEAKER BOXES AS FAR APART AS POSSIBLE FOR BEST SOUND EFFECT.
- UNWRAP THE SPEAKER-CORDS OF BOTH SPEAKER-BOXES.
- INSERT THE "RED" WIRE OF THE LEFT SPEAKER-BOX INTO THE "RED" ( + ) SPEAKER
CONNECTOR BEHIND THE MAIN-UNIT, WHICH HAS THE "L" INDICATION (UNDER THE
SPEAKER-CONNECTOR).
- INSERT THE "BLACK" WIRE OF THE LEFT SPEAKER-BOX INTO THE "BLACK" ( - )
SPEAKER CONNECTOR BEHIND THE MAIN-UNIT, WHICH HAS THE "L" INDICATION
(UNDER THE SPEAKER-CONNECTOR).
- REPEAT THE ABOVE 2 STEPS FOR THE RED & BLACK WIRES OF THE "RIGHT"
SPEAKER BOX, BUT THIS TIME, INSERTING THEM INTO THE RED & BLACK
CONNECTORS WITH THE "R" INDICATION.
- WHEN INSERTING EACH WIRE INTO A CONNECTOR, PRESS DOWNWARDS ON
THE CONNECTOR'S PLASTIC KNOB (RED OR BLACK PART) & PUSH THE EXPOSED
METAL END OF THE WIRE ALL THE WAY INTO THE HOLE ABOVE THIS KNOB.
USE THE BASE OF MAIN UNIT
AS A "TEMPLATE" FOR FIXING
THE 2 SCREWS ON THE WILL.
THE 2 GUIDE HOLES (SEE DIAGRAM)
WILL HELP YOU TO OBTAIN EXACT
LOCATIONS OF THE SCREWS.
ONCE YOU HAVE MOUNTED THE MAIN UNIT IN IT'S INTENDED LOCATION,
FIX THE SPEAKER POSITIONS AS DESIRED. PLEASE TAKE CARE TO LEAVE
ENOUGH ROOM FOR THE SLIDING CD-DOOR TO OPEN (SEE DIAGRAM BELOW).
E-9 E-10
LIMITED 90 DAY WARRANTY
We warrant this product to be free from defects in material and workmanship under normal
use for a 90-day period after purchase. We will repair or replace the unit free of charge
should it become defective under this warranty, providing you submit proof of purchase
During the initial 90 day period after original purchase, we will service or exchange,
at no charge. To obtain warranty service or replacement within the duration of the
(sales slip) along with the unit and all accessories.
90-day warranty, return the product freight prepaid to the address below.
eTEC USA
823 Old Settlers Trail
Suite 100
Hopkins, Minnesota 55343
UNDER NO CIRCUMSTANCES WILL ETEC USA BE LIABLE FOR ANY
INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Please enclose a copy of the sales receipt with the date of purchase and provide a detailed
description of the problem. Failure to enclose required information will result in delay of
This warranty does not cover any product, which has been subject to damage due to an act
of God, misuse, neglect, accident, abuse, commercial use, or modification of, or to, any
part of the product, including the antenna. Damage to external devices such as speakers
and other memory devices are not covered nor is the cost incurred in shipping the unit for
warranty repair. Under no circumstances shall eTEC USA, be liable for any loss (direct,
indirect, incidental, foreseen, unforeseen, special or consequential) or for any damage
your shipment. Please allow 4-6 weeks for product service or replacement.
arising out of, or in connection with, the use of this product.
This warranty does not cover re-manufactured units, or product sold 'As Is'.
This warranty is valid only in the United States and grants specific legal rights.
DATE : 5 FEB, 2007
MODEL A707DXI “eTEC”
REVISED WARRANTY FOR APPROVAL
SIZE : 102 (W) X 136 (H) MM
PRINTING COLOR : BLACK
DATE : 5 FEB, 2007
MODEL A707DXI “eTEC”
FOLDING PLAN FOR APPROVAL
SIZE : 102 (W) X 136 (H) MM FOR EACH PAGE
PRINTING COLOR : BLACK
(FRONT)
COVER
E-2
E-3 E-4
E-5
(BACK)
E-6
E-7
E-8 E-9 E-10
WARRANTY
BLANK
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

Etec A707DXI Operating Instructions Manual

Etec
Brand
Etec
Model
A707DXI
Category
CD players
Type
Operating Instructions Manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents