Asco Series 488 seal kits and repair User manual

Asco
Brand
Asco
Model
Series 488 seal kits and repair
Type
User manual

Asco Series 488 seal kits and repair

Below you will find brief product information for Asco Series 488 seal kits and repair. These kits are designed to help you maintain and repair your Asco Series 488 cylinders.

The kits include all of the necessary seals and wear elements to rebuild your cylinder, including:

  • Piston seal
  • O-ring
  • Rod seal
  • Wear band
  • Bumpers
  • Cushion seals (if applicable)

The kits are available in a variety of bore sizes to fit your specific cylinder. They are also easy to install, following the step-by-step instructions included with each kit.

Asco Series 488 seal kits and repair

Below you will find brief product information for Asco Series 488 seal kits and repair. These kits are designed to help you maintain and repair your Asco Series 488 cylinders.

The kits include all of the necessary seals and wear elements to rebuild your cylinder, including:

  • Piston seal
  • O-ring
  • Rod seal
  • Wear band
  • Bumpers
  • Cushion seals (if applicable)

The kits are available in a variety of bore sizes to fit your specific cylinder. They are also easy to install, following the step-by-step instructions included with each kit.

Information subject to change without notice. For ordering information or regarding your local sales office, please visit www.numatics.com.
23
SEAL KITS - HOW TO ORDER
SERIES
488
Bore Ø (mm) Kit Number
Parts Included
1 2 3 4 5 6
Piston Seal O-Ring Rod Seal Wear Band Bumper Cushion Seal
Single Rod Seal Kits
20
M488502568LN001 • • • • • • • •
25
M488502568MN002 • • • • • • • •
32
M4885025683N003 • • • • • • • •
40
M4885025684N004 • • • • • • • •
50
M4885025685N005 • • • • • • • •
63
M4885025686N006 • • • • • • • •
80
M4885025688N007 • • • • • • • •
20
M488506073LN001 • • • • • •
25
M488506073MN002 • • • • • •
32
M4885060733N003 • • • • • •
40
M4885060734N004 • • • • • •
50
M4885060735N005 • • • • • •
63
M4885060736N006 • • • • • •
80
M4885060738N007 • • • • • •
Double Rod Seal Kits
20
M488506074LN001 • • • • • • • • •
25
M488506074MN002 • • • • • • • • •
32
M4885060743N003 • • • • • • • • •
40
M4885060744N004 • • • • • • • • •
50
M4885060745N005 • • • • • • • • •
63
M4885060746N006 • • • • • • • • •
80
M4885060748N007 • • • • • • • • •
20
M488506075LN001 • • • • • • •
25
M488506075MN002 • • • • • • •
32
M4885060753N003 • • • • • • •
40
M4885060754N004 • • • • • • •
50
M4885060755N005 • • • • • • •
63
M4885060756N006 • • • • • • •
80
M4885060758N007 • • • • • • •
How to Order - Seal Kit
Information subject to change without notice. For ordering information or regarding your local sales office, please visit www.numatics.com.
24
SERIES
488
1. 1. Safely disconnect the cylinder air lines, rod mount and if applicable other mechanical attachments as directed
by machine manufacturer.
2. 2. Remove all mounting accessories from the cylinder.
3. 3. Locate the mounting flats on the front cap (circled above).
4. 4. Using these designated flats, gently loosen the front cap with a wrench and unthread the tube using a strap wrench or
concave devise of similar diameter WARNING: Do not grip the rear cap end of the cylinder or deform the ID of the tube.
5. 5. Carefully remove all internal sealing and wear elements from the head and piston assembly without nicking
or damaging them.
6. 6. If rod bushing is worn more than .13mm out of round, replace head assembly or entire cylinder.
7. 7. With a lint free cloth, remove grease from internal elements as well as the inside of the tube and piston rod.
8. 8. Thoroughly re-lubricate all new replacement seals and tube inside diameter using grease provided. Do not lubricate
the rod bushing.
9. 9. Carefully reassemble all elements back onto the head and piston assembly (as seen in the diagram on the previous page):
10. 1 Piston Seal
11. 2 O-ring
12. 3 Rod Seal
13. 4 Wear Band
14. 5 Bumpers
15. 6 Cushion Seals (if applicable)
16. 10. Using a sinking tube slide the piston rod assembly back into the freshly lubricated tube.
17. 11. Thread the head back onto the cylinder tube, over the piston rod. Torque cylinder 1
°
-2
°
past origin.
Note: Not recommended for C01 Foot Mounts. Misalignment of the mounting holes, flats and ports may occur.
18. 12. Re-attach mounting accessories and then safely back onto machine.
Seal Kit Removal/Installation Instructions
SEAL KIT INSTRUCTIONS
  • Page 1 1
  • Page 2 2

Asco Series 488 seal kits and repair User manual

Asco
Brand
Asco
Model
Series 488 seal kits and repair
Type
User manual

Asco Series 488 seal kits and repair

Below you will find brief product information for Asco Series 488 seal kits and repair. These kits are designed to help you maintain and repair your Asco Series 488 cylinders.

The kits include all of the necessary seals and wear elements to rebuild your cylinder, including:

  • Piston seal
  • O-ring
  • Rod seal
  • Wear band
  • Bumpers
  • Cushion seals (if applicable)

The kits are available in a variety of bore sizes to fit your specific cylinder. They are also easy to install, following the step-by-step instructions included with each kit.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents