Gigabyte GA-8I915P Ultra User manual

GA-8I915P Series

Intel

®

Pentium

®

4 LGA775 Processor Motherboard

User's Manual

Rev. 2002

12ME-8I915PU-2002

Motherboard

GA-8I915P/GA-8I915P Ultra/

GA-8I915P Pro/GA-8I915P-G

Aug. 17, 2004

Aug.17, 2004

Motherboard

GA-8I915P/GA-8I915P Ultra/GA-8I915P Pro/GA-8I915P-G

Copyright

The trademarks mentioned in the manual are legally registered to their respective companies.

Notice

The written content provided with this product is the property of Gigabyte.

No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any

means without Gigabyte's prior written permission. Specifications and features are subject to

change without prior notice.

Product Manual Classification

In order to assist in the use of this product, Gigabyte has categorized the user manual in the

following:

n For quick installation, please refer to the "Hardware Installation Guide" included with the

product.

n For detailed product information and specifications, please carefully read the

"Product User Manual".

n For detailed information related to Gigabyte's unique features, please go to "Technology

Guide" section on Gigabyte's website to read or download the information you need.

Fore more product details, please click onto Gigabyte's website at www.gigabyte.com.tw

- 4 -

Table of Contents

GA-8I915P (Ultra)(Pro)(-G) Motherboard Layout ........................................................6

Block Diagram ...........................................................................................................7

Chapter 1 Hardware Installation ..................................................................................9

1-1 Considerations Prior to Installation ......................................................................... 9

1-2 Feature Summary .................................................................................................10

1-3 Installation of the CPU and Heatsink ...................................................................12

1-3-1 Installation of the CPU .................................................................................... 12

1-3-2 Installation of the Heatsink .............................................................................. 13

1-4 Installation of Memory...........................................................................................14

1-5 Install expansion cards .........................................................................................16

1-6 I/O Back Panel Introduction .................................................................................17

1-7 Connectors Introduction ........................................................................................18

Chapter 2 BIOS Setup ............................................................................................ 29

The Main Menu (For example: BIOS Ver. : F1) ............................................................30

2-1 Standard CMOS Features ...................................................................................32

2-2 Advanced BIOS Features ....................................................................................34

2-3 Integrated Peripherals ...........................................................................................36

2-4 Power Management Setup ...................................................................................40

2-5 PnP/PCI Configurations .......................................................................................42

2-6 PC Health Status ..................................................................................................43

2-7 MB Intelligent Tweaker(M.I.T.) .............................................................................44

2-8 Load Fail-Safe Defaults .........................................................................................46

2-9 Load Optimized Defaults .......................................................................................46

2-10 Set Supervisor/User Password .......................................................................... 47

2-11 Save & Exit Setup ...............................................................................................48

2-12 Exit Without Saving .............................................................................................. 48

- 5 -

Chapter 3 Install Drivers ......................................................................................... 49

3-1 Install Chipset Drivers ..........................................................................................49

3-2 Software Applications ............................................................................................50

3-3 Driver CD Information ...........................................................................................50

3-4 Hardware Information ...........................................................................................51

3-5 Contact Us ............................................................................................................51

Chapter 4 Appendix ............................................................................................... 53

4-1 Unique Software Utilities ......................................................................................53

4-1-1 Xpress Recovery Introduction ....................................................................... 54

4-1-2 Flash BIOS Method Introduction .................................................................... 57

4-1-3 2 / 4 / 5.1 / 7.1 Channel Audio Function Introduction .................................. 68

4-2 Troubleshooting ......................................................................................................74

- 6 -

GA-8I915P (Ultra)(Pro)(-G) Motherboard Layout

KB_MS

ATX_12V

CPU_FAN

LGA 775

LPT

ATX

GA-8I915P (Ultra)(Pro)(-G)

COMA

DDR1

DDR2

DDR3

DDR4

PWR_FAN

SPDIF_OUT

SPDIF_IN

CODEC

F_U SB1

IT8712

Intel ICH 6

BACK

BIOS

PCI2

F2_1 394

F1_1 394

BAT

PCI1

F_U SB2

TSB43AB23

PWR_LED

F_PAN EL

SYS_FAN

CLR_CMOS

PCIE_3

PCIE_2

MAIN

BIOS

IR

S_ATA1

AUDIO1

Intel 915P

PCIE_16

USB

PCIE_1

AZALIA_FP

IDE1

FDD

CD_IN

USB

LAN

S_ATA4

S_ATA2

Marv ell

8001AUDIO2

S_ATA3

NB_FAN

IDE3

IDE2

IT8212

Only for GA-8I915P Ultra.

Only for GA-8I915P Pro.

Only for GA-8I915P-G.

- 7 -

Block Diagram

LGA775

Processor

CPUCLK+/-(200/133MHz)

PCI Express x16

33MHz

Host

Interface

Intel

915P

MCH

MCHCLK (200/133M Hz)

66MHz

48MHz

LPT Port

COM Port

Floppy

PS/2 KB/M ouse

24MHz

33MHz

IT 8712

4 Serial ATA

ATA33/66/100

IDE1 Channels

Intel

ICH6

3 PCI E xpressx 1 Ports

14.318MHz

Dual BIOS

8 USB

Ports

PCI Express x1 Bus

PCICLK

(33MHz)

2 PCI

PCI Bus

Line-Out

MIC

Surround Speaker Out

Center/Subwoofer Speaker Out

Back Surround Speaker Out

CODEC

Line-In

SPDIF In

SPDIF Out

3 IEEE1394

TSB43AB23

Marvell

8001

RJ45

DDR 400/333/266MHz DIMM

Dual Channel Memory

PCI-ECLK

(100MHz)

PCI-ECLK

(100MHz)

IDE2/IDE3

IT8212

IDE RAID

Only for GA-8I915P Ultra.

Only for GA-8I915P Pro.

Only for GA-8I915P-G.

- 8 -

Hardware Installation- 9 -

English

1-1 Considerations Prior to Installation

Preparing Your Computer

The motherboard contains numerous delicate electronic circuits and components which can

become damaged as a result of electrostatic discharge (ESD). Thus, prior to installation, please

follow the instructions below:

1. Please turn off the computer and unplug its power cord.

2. When handling the motherboard, avoid touching any metal leads or connectors.

3. It is best to wear an electrostatic discharge (ESD) cuff when handling electronic components

(CPU, RAM).

4. Prior to installing the electronic components, please have these items on top of an antistatic pad or

within a electrostatic shielding container.

5. Please verify that you the power supply is switched off before unplugging the power supply connector

from the motherboard.

Installation Notices

1. Prior to installation, please do not remove the stickers on the motherboard. These stickers are required

for warranty validation.

2. Prior to the installation of the motherboard or any hardware, please first carefully read the information

in the provided manual.

3. Before using the product, please verify that all cables and power connectors are connected.

4. To prevent damage to the motherboard, please do not allow screws to come in contact with the

motherboard circuit or its components.

5. Please make sure there are no leftover screws or metal components placed on the motherboard or

within the computer casing.

6. Please do not place the computer system on an uneven surface.

7. Turning on the computer power during the installation process can lead to damage to system

components as well as physical harm to the user.

8. If you are uncertain about any installation steps or have a problem related to the use of the product,

please consult a certified computer technician.

Instances of Non-Warranty

1. Damage due to natural disaster, accident or human cause.

2. Damage as a result of violating the conditions recommended in the user manual.

3. Damage due to improper installation.

4. Damage due to use of uncertified components.

5. Damage due to use exceeding the permitted parameters.

6. Product determined to be an unofficial Gigabyte product.

Chapter 1 Hardware Installation

GA-8I915P Series Motherboard - 10 -

English

CPU w Supports the latest Intel

®

Pentium

®

4 LGA775 CPU

w Supports 800/533MHz FSB

w L2 cache varies with CPU

Motherboard w GA-8I915P Series Motherboard:

GA-8I915P Ultra/GA-8I915P Pro/GA-8I915P-G/GA-8I915P

Chipset w Northbridge: Intel

®

915P Express Chipset

w Southbridge: Intel

®

ICH6

Memory w 4 DDR DIMM memory slots (supports up to 4GB m emory)

(Note 1)

w Supports dual channel DDR400/333/266 DIMM

w Supports 2.5V DDR DIMM

Slots w 1 PCI Express x 16 slot

w 3 PCI Express x 1 slots

w 2 PCI slots

IDE Connections w 1 IDE connection (UDM A 33/ATA 66/ATA 100), allows connection of 2

IDE devices (IDE1)

w 2 IDE connection (UDMA 33/ATA 66/ATA 100/ATA 133), compatible with

RAID, allows connection of 4 IDE devices (IDE2,IDE3)

FDD Connections w 1 FDD connection, allows connection of 2 FDD devices

Onboard SATA w 4 Serial ATA connections

Peripherals w 1 parallel port supporting Normal/EPP/ECP mode

w 1 Serial port (COM A)

w 8 USB 2.0/1.1 ports (rear x 4, front x 4 via cable)

w 3 IEEE1394 ports (requires cable)

w 1 front audio connector

w 1 IR connector

w 1 PS/2 keyboard port

w 1 PS/2 mouse port

Onboard LAN w Onboard Marvell 8001 chip (10/100/1000 Mbit)

w 1 RJ 45 port

Onboard Audio w C-Media 9880 CODEC (UAJ)

w Supports Jack Sensing function

w Supports 2 / 4 / 5.1 / 7.1 channel audio

w Supports Line In ; Line Out ; MIC ; Back Surround Speaker Out ;

Center/Subwoofer Speaker Out ; Surround Speaker Out connection

w Supports SPDIF In/Out connection

w CD In

(Note 1) Due to standard PC architecture, a certain amount of memory is reserved for system usage and

therefore the actual memory size is less than the stated amount.

For example, 4 GB of memory size will instead be shown as 3.xxGB memory during system startup.

1-2 Feature Summary

Only for GA-8I915P Ultra.

Only for GA-8I915P Pro.

Only for GA-8I915P-G.

Hardware Installation- 11 -

English

On-Board IDE RAID w Onboard GigaRAID IT8212 chipset

(IDE2, IDE3) w Supports disk striping (RAID 0) or disk m irroring (RAID 1) or

striping + mirroring (RAID 0 + RAID 1)

w Supports JBOD function

w Supports concurrent dual ATA133 IDE controller operation

w Supports ATAPI m ode for HDD

w Supports IDE bus master operation

w Supports ATA133/RAID m ode switch by BIOS

w Displays status and error checking m essages during boot-up

w Mirroring supports autom atic background rebuilds

w Features LBA and Extended Interrupt 13 drive translation in

controller onboard BIOS

I/O Control w IT8712

Hardware M onitor w CPU / System / Power fan speed detection

w CPU temperature detection

w System voltage detection

w CPU / System / Power fan failure warning

w CPU Smart FAN Control

BIOS w Use of licensed AWARD BIOS

w Supports Dual BIOS /Q-Flash

Additional Features w Supports @BIOS

w Supports EasyTune

Overclocking w Over Voltage via BIOS (CPU/DDR/PCI-E)

w Over Clock via BIOS (CPU/DDR)

Form Factor w ATX form factor; 30.5cm x 24.4cm

Only for GA-8I915P Ultra.

Only for GA-8I915P Pro.

GA-8I915P Series Motherboard - 12 -

English

1-3 Installation of the CPU and Heatsink

Before installing the CPU, please comply with the following conditions:

1. Please make sure that the motherboard supports the CPU.

2. Please take note of the one indented corner of the CPU. If you install the CPU in the wrong

direction, the CPU will not insert properly. If this occurs, please change the insert direction

of the CPU.

3. Please add an even layer of heat sink paste between the CPU and heatsink.

4. Please make sure the heatsink is installed on the CPU prior to system use, otherwise

overheating and permanent damage of the CPU may occur.

5. Please set the CPU host frequency in accordance with the processor specifications. It is not

recommended that the system bus frequency be set beyond hardware specifications since it

does not meet the required standards for the peripherals. If you wish to set the frequency

beyond the proper specifications, please do so according to your hardware specifications

including the CPU, graphics card, memory, hard drive, etc.

HT functionality requirement content :

Enabling the functionality of Hyper-Threading Technology for your computer system requires all

of the following platform components:

- CPU: An Intel

®

Pentium 4 Processor with HT Technology

- Chipset: An Intel

®

Chipset that supports HT Technology

- BIOS: A BIOS that supports HT Technology and has it enabled

- OS: An operation system that has optimizations for HT Technology

1-3-1 Installation of the CPU

Fig. 1

Gently lift the m etal

lever located on the

CPU socket to the

upright position.

Metal Lever

Fig. 2

Rem ov e the pl astic

covering on the CPU

socket.

Fig. 3

Notice the sm all gold

colored triangle

located on the edge of

the CPU socket.

Align the indented

corner of the CPU with

Fig. 4

Once the CPU is

properly inserted,

please replace the

plastic covering and

push the m etal lever

back into its original

position.the triangle and gently insert the CPU into position.

(Grasping the CPU firm ly between your thum b

and forefinger, carefully place it into the socket in a

straight and downwards motion. Avoid twisting or

bending motions that m ight cause dam age to the

CPU during installation.)

Hardware Installation- 13 -

English

1-3-2 Installation of the Heatsink

Fig.1

Please apply an even layer of heatsink paste on

the surface of the installed CPU.

The heatsink may adhere to the CPU as a result of hardening of the heatsink paste.To prevent

such an occurrence, it is suggested that either thermal tape rather than heat sink paste be used

for heat dissipation or using extreme care when removing the heatsink.

Fig. 6

Finally, please attach the power connector of the

heatsink to the CPU fan header located on the

motherboard.

Fig. 3

Place the heatsink atop the CPU and m ake sure

the push pins aim to the pin hole on the

m otherboard.Pressing down the push pins

diagonally.

Fig. 2

(Turning the push pin along the direction of arrow

is to rem ove the heatsink, on the contrary, is to

install.)

Please note the direction of arrow sign on the m ale

push pin doesn't face inwards before installation.

(This instruction is only for Intel boxed fan)

Fig. 4

Please make sure the Male and Female push pin

are join ed cl osely . (fo r de tail ed i nsta llation

instructions, please refer to the heatsink installation

section of the user manual)

Fig. 5

Please check the back of m otherboard after

installing. If the push pin is inserted as the picture,

the installation is com plete.

Male Push Pin

Female Push Pin

The top of Female Push Pin

GA-8I915P Series Motherboard - 14 -

English

Before installing the memory modules, please comply with the following conditions:

1 . Please make sure that the memory used is supported by the motherboard. It is recommended that

me mo ry o f si mi la r ca pa ci ty , spe ci fi ca ti on s an d br an d be u se d.

2 . Be fo re i ns ta ll in g or r em ov ing m em or y mo du le s, p le as e m ak e su re t ha t th e co mp ut er

p ow e r i s sw i t ch e d

o ff t o p re v en t h ar dw a re d a ma ge .

3 . Memory modules have a foolproof insertion design. A memory module can be installed in only one

direction. If you are unable to insert the module, please switch the direction.

Notch

DDR

1-4 Installation of Memory

The m otherboard supports DDR memory modules, whereby BIOS will autom atically detect m emory

capacity and specifications. M emory modules are designed so that they can be inserted only in one

direction. The memory capacity used can differ with each slot.

Fig.1

The DIMM socket has a notch, so the DIMM memory module can

only fit in one direction. Insert the DIMM memory module vertically

into the DIMM socket. Then push it down.

Fig.2

Close the plastic clip at both edges of the DIMM sockets to lock

the DIMM module.

Reverse the installation steps when you wish to remove the DIMM

module.

Hardware Installation- 15 -

English

Dual Channel DDR

GA-8I915P Series supports the Dual Channel Technology. After operating the Dual Channel Technology,

the bandwidth of Mem ory Bus will add double up to 6.4GB/s.

GA-8I915P Series includes 4 DIMM sockets, and each Channel has two DIM M sockets as following:

Channel A : DDR 1, DDR 2

Channel B : DDR 3, DDR 4

If you want to operate the Dual Channel Technology, please note the following explanations due

to the limitation of Intel chipset specifications.

1. One/three DDR mem ory module is installed: The Dual Channel Technology can't operate

when only one DDR mem ory module is installed.

2. Two DDR mem ory modules are installed (the sam e m emory size and type): The Dual

Channel Technology will operate when two m em ory m odules are inserted individually into

Channel A and B. If you install two mem ory modules in the same channel, the Dual Channel

Technology will not operate.

3. Four DDR memory modules are installed: If you install four mem ory modules at the same

time, the Dual Channel Technology will operate only when those modules have the same

memory size and type.

We'll strongly recom mend our user to slot two DDR memory m odules into the DIMMs with the same

color in order for Dual Channel Technology to work.

The following table is for Dual Channel Technology com bination: (DS: Double Side, SS: Single Side)

2 memory modules

4 memory modules

DDR 1 DDR 2 DDR 3 DDR 4

DS/SS X DS/SS X

X DS/SS X DS/SS

DS/SS DS/SS DS/SS DS/SS

GA-8I915P Series Motherboard - 16 -

English

1-5 Install expansion cards

You can install your expansion card by following the steps outlined below:

1. Read the related expansion card's instruction document before install the expansion card into the

computer.

2. Remove your computer's chassis cover, screws and slot bracket from the computer.

3. Press the expansion card firmly into expansion slot in motherboard.

4. Be sure the metal contacts on the card are indeed seated in the slot.

5. Replace the screw to secure the slot bracket of the expansion card.

6. Replace your computer's chassis cover.

7. Power on the computer, if necessary, setup BIOS utility of expansion card from BIOS.

8. Install related driver from the operating system.

Installing a PCI Express x 16 expansion card:

Please carefully pull out the small white-

drawable bar at the end of the

PCI Express x 16 slot when you try to

install/Uninstall the VGA card. Please align

the VGA card to the onboard

PCI Express x 16 slot and press firmly

down on the slot .M ake sure your VGA

card is locked by the sm all white-draw-

able bar.

Hardware Installation- 17 -

English

1-6 I/O Back Panel Introduction

PS/2 Keyboard and PS/2 Mouse Connector

To install a PS/2 port keyboard and mouse, plug the mouse to the upper port (green) and the keyboard

to the lower port (purple).

Parallel Port

The parallel port allows connection of a printer, scanner and other peripheral devices.

SPDIF_O (SPDIF Out)

The SPDIF output is capable of providing digital audio to external speakers or compressed AC3

data to an external Dolby Digital Decoder.

SPDIF_I (SPDIF In)

Use SPDIF In feature only when your device has digital output function.

COM A (Serial Port)

Connects to serial-based m ouse or data processing devices.

USB port

Before you connect your device(s) into USB connector(s), please make sure your device(s) such

as USB keyboard, mouse, scanner, zip, speaker...etc. have a standard USB interface.

Also make sure your OS supports USB controller. If your OS does not support USB controller,

please contact OS vendor for possible patch or driver upgrade. For more information please

contact your OS or device(s) vendors.

LAN Port

The provided Internet connection is Gigabit Ethernet, providing data transfer speeds of

10/100/1000Mbps.

Line In

Devices like CD-ROM , walkm an etc. can be connected to Line In jack.

Line Out (Front Speaker Out)

Connect the stereo speakers, earphone or front surround channels to this connector.

MIC In

Microphone can be connected to MIC In jack.

Only for GA-8I915P Ultra.

Only for GA-8I915P Pro.

Only for GA-8I915P-G.

GA-8I915P Series Motherboard - 18 -

English

1-7 Connectors Introduction

2

1

14

4

18

8

3

12

13

16

17 11

15

7

5

10

19

You can use audio software to configure 2-/4-/5.1-/7.1-channel audio functioning.

6

Back Surround Speaker Out

Connect the back surround channels to this connector.

Center/Subwoofer Speaker Out

Connect the Center/Subwoofer channels to this connector.

Surround Speaker Out

Connect the surround channels to this connector.

1) ATX_12V

2) ATX (Power Connector)

3) CPU_FAN

4) SYS_FAN

5) PWR_FAN

6) NB_ FAN

7) FDD

8) IDE1

9) IDE2/IDE3

10) S_ATA1 / S_ATA2 / S_ATA3 / S_ATA4

11) PWR_LED

12) F_PANEL

13) AZALIA_FP

14) CD_IN

15) F_USB1 / F_USB2

16) F1_1394 / F2_1394

17) I R

18) CLR_CMOS

19) BAT

9

Only for GA-8I915P Ultra.

Only for GA-8I915P Pro.

Hardware Installation- 19 -

English

Pin No. Definition

1 GND

2 GND

3 +12V

4 +12V

1/2) ATX_12V/ATX (Power Connector)

With the use of the power connector, the power supply can supply enough stable power to all the

components on the motherboard. Before connecting the power connector, please make sure that all

components and devices are properly installed. Align the power connector with its proper location on

the motherboard and connect tightly.

The ATX_12V power connector mainly supplies power to the CPU. If the ATX_12V power connector

is not connected, the system will not start.

Caution!

Please use a power supply that is able to handle the system voltage requirements. It is

recommended that a power supply that can withstand high power consumption be used (300W or

greater). If a power supply is used that does not provide the required power, the result can lead to an

unstable system or a system that is unable to start.

Please remove the sticker on the motherboard before plugging in while the ATX power supplier is 24

pins; Otherwise, please do not remove it.

Pin No. Definition

1 3.3V

2 3.3V

3 GND

4 VCC

5 GND

6 VCC

7 GND

8 Power Good

9 5V SB(stand by +5V)

10 +12V

11 +12V

12 3.3V(Only for 24pins ATX)

13 3.3V

14 -12V

15 GND

16 PS_ON(soft On/Off)

17 GND

18 GND

19 GND

20 -5V

21 VCC

22 VCC

23 VCC

24 GND

2 4

1 3

1 2

1

3

1

4

2

GA-8I915P Series Motherboard - 20 -

English

3/4/5) CPU_FAN / SYS_FAN / PWR_FAN (Cooler Fan Power Connector)

The cooler fan power connector supplies a +12V power voltage via a 3-pin/4-pin (only for

CPU_FAN) power connector and possesses a foolproof connection design.

Most coolers are designed with color-coded power connector wires. A red power connector

wire indicates a positive connection and requires a +12V power voltage. The black connector

wire is the ground wire (GND).

Please remember to connect the power to the cooler to prevent system overheating and

failure.

Caution! Please remember to connect the power to the CPU fan to prevent CPU overheating

and failure.

1

CPU_FAN

SYS_FAN

PWR_FAN

1

Pin No. Definition

1 GND

2 +12V

3 Sense

4 Speed Control

(Only for CPU_FAN)

6) NB_FAN (Chip Fan Connector)

If you installed wrong direction, the chip fan will not work. Sometimes will damage the chip fan.

(Usually black cable is GND)

Pin No. Definition

1 +12V

2 GND

1

Page is loading ...

Gigabyte GA-8I915P Ultra User manual

This manual is also suitable for

Gigabyte GA-8I915P Ultra User manual

Related papers

Other documents