OWNER'S MANUAL
MODEL
XTRPRO102D
XTRPRO104D
XTRPRO122D
XTRPRO124D
XTRPRO152D
XTRPRO154D
Subwoofer
1
TABLE OF CONTENTS
English . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
PracticeSafeSound™ ................................................
1
What'sinthebox.. .................................................
.2
Tools of the Trade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
Installation .........................................................
2
Finding Speaker Mounting Locations . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . .
2
Features ..........................................................
3
Wiring Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Specifications ......................................................
14
EnclosureRecommendations...........................................
18
Warranty ................................ .................. Backcover
INTRODUCTION
Thank you for your purchase of the Orion XTRPRO Subwoofers. These woofers
represent a combination of incredible performance and value.
PRACTICE SAFE SOUND™
Continuous exposure to sound pressure levels over 100dB may cause permanent
hearing loss. High powered automotive sound systems can generate sound pressure
levels in excess of 130dB. When playing your system at high levels, please use hearing
protection and prevent long term exposure.
Model Number:
Serial Number:
Date of Purchase:
2
WHAT’S IN THE BOX
Included in this box are all the necessary mounting hardware and cables for your basic
installation. Listed below is a detailed list of the components included in this system
package.
Quantity Description
1
Owner's Manual
1
Orion XTRPRO woofer
1
Mounting template
1
Trim ring with hardware..
TOOLS OF THE TRADE
Listed are the majority of the tools required to perform the installation. Having the
proper tools will make the installation much easier. It is very difficult when you get
half way through the installation and discover that you require a specific tool to
get yourself through a particular part of the installation. Some of these tools are
necessities. Some make the job much easier.
Marking Pen Electric Drill and assorted Bits
Phillips Screwdriver Wire Strippers
Allen Wrenches Volt/Ohm Meter (Optional)
Table Saw Jig Saw
Wire Cutters Wire Crimpers
INSTALLATION
The performance of these XTRPRO subwoofers is directly proportional to the quality
of the installation. Care taken with the installation process will be rewarded by years
of satisfying performance. If you are unsure of your installation abilities, please
refer to your local authorized ORION dealer for assistance. Orion dealers are trained
professionals dedicated to extracting the maximum performance out of your Orion
system. If you decide to install this speaker system yourself, please read the entire
section on sealed and vented enclosures before starting the installation.
FINDING SPEAKER MOUNTING LOCATIONS
Choosing the correct speaker locations will have the greatest effect on the sound
quality of the system. Different considerations are needed when choosing the
locations that best suit your needs. The locations must be large enough for the
speakers to fit. Care is needed to ensure that the location you have chosen will not
affect any of the mechanical or electrical operations of the vehicle.
Determining the best location for the speakers will depend on your cosmetic needs
and your vehicle’s interior. Usually the woofers are installed in the trunk, rear seat, or
rear of the vehicle..
3
FEATURES
Figure
1
Figura
1
Abbildung
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
1 Polypropylene dust cap - moisture and UV resistant.
2 Oversized Santoprene surround for linear controlled long excursion.
3 Vented paper cone - moisture and UV resistant.
4 Custom stamped aluminum frame.
5 Spider ring attachment screws.Part of re-cone feature (8 hex screws)
6 Vented Kapton voice coil former (10” uses 2.5" voice coil former, 12” & 15" use a 3"
voice coil former).
7 20mm H type steel front plate
8 Large 2 stack ceramic magnets (15” use large 3 stack ceramic magnets).
9 12mm steel back plate/pole piece T yoke assembly.
10 1.2"(10” speaker) & 1.4”(12” & 15" speaker) vent. Part of the enhanced voice coil
cooling system (forced convection).
11 PVC magnet protector.
12 High temperature Aluminum voice coil wound.Dual 2 and 4 ohm voice coils
available.
13 Dual Interlaced Conex spider with stitched and looped tinsel leads attached.
14 Custom allen head screw terminals.A pair on each side(one pair for each voice coil).
15 Spider space and spider mounting ring assembly part of field re-cone kit attachment
method.(eight allen head screws).
16 Surround clamp ring,part of fiele re-cone kit attachment method.(10” & 12” use
eight allen head screws, 15” use twelve allen head screws).
2 ohm
2 ohm
++
+
__
_
2 ohm
2 ohm
++
+
_
_
_
4 ohm
4 ohm
++
+
_
_
_
4 ohm
4 ohm
+
+
--
4 ohm
4 ohm
+
+
--
+
-
Figure 5
Figura 5
Abbildung 5
2 ohm
2 ohm
+
+
--
2 ohm
2 ohm
+
+
--
+
-
Figure 6
Figura 6
Abbildung 6
4 ohm
4 ohm
+
+
--
4 ohm
4 ohm
+
+
--
4 ohm
4 ohm
+
+
--
+
-
Figure 7
Figura 7
Abbildung 7
2 ohm
2 ohm
+
+
--
2 ohm
2 ohm
+
+
--
2 ohm
2 ohm
+
+
--
+
-
Figure 8
Figura 8
Abbildung 8
4 ohm
4 ohm
4 ohm
4 ohm
4 ohm
4 ohm
4 ohm
4 ohm
+
-
+
+
--
+
+
--
+
+
--
+
+
--
Figure 9
Figura 9
Abbildung 9
2 ohm
2 ohm
2 ohm
2 ohm
2 ohm
2 ohm
2 ohm
2 ohm
+
-
+
+
--
+
+
--
+
+
--
+
+
--
Figure 10
Figura 10
Abbildung 10
2 ohm
2 ohm
++
--
+
-
+
-
Figure 11
Figura 11
Abbildung 11
4 ohm
4 ohm
++
--
+
-
+
-
Figure 12
Figura 12
Abbildung 12
14
SPECIFICATIONS
Specifications are subject to change without notice
Model/Part Number
Fs (free-air resonance, Hz)
Vas (equivalent compliance, cu. ft.)
Vas (equivalent compliance, liters)
Qms (Q, mechanical)
Qes (Q, electrical)
Qts (total driver Q)
Re (DC resistance, ohms)
Z (nominal impedance, ohms)
Le (inductance, mh)
Efficiency (1W @ 1M, dB)
Efficiency (2.86V @ 1M, dB)
Xmax (one way linear excursion, in.)
Xmax (one way linear excursion, mm)
RMS Power Watts
Nominal Power Watts
MAX Music Power Watts*
Mms (total moving mass, grams)
Cms (mechanical compliance, mm/N)
Bl (motor strength, Tesla-M)
Sd (effective radiating area, sq. cm.)
Sd (effective radiating area, sq. in.)
Frequency range (Hz)
Energy Bandwidth Product (EBP)**
Speaker Displacement (cu ft)
Mounting hole diameter (inches/mm) 11.34 / 288 11.34 / 288 13.35 / 339
Mounting depth (inches/mm) 7.27 / 185 7.27 / 185 7.70 / 196
Magnet Weight (Oz)
Basket diameter (inches/mm)
Typical sealed enclosure (cu. ft.)
Vented enclosure (cu. ft.)***
Port tuning frequency (Hz)
Port diameter (inside,inches)
Port square equivalent (inches)
Port length (inches)
250018001800
3
11.19
2.659x2.659
8
3.797
88.7
0.472
88.7
9.6
0.382
0.368
6.8
12
3600
145.959
900
0.116
25.886
366.44
56.798
133
44
35 - 1kHz
0.1204
101
Recommended Enclosures
0.75
0.75
11.349
0.5
0.479
XTRPRO122D
37.1
1.033
29.255
Thiele/Small Parameters
XTRPRO104D
38.7
0.779
22.056
3.4
4
2.392
88.6
91.6
0.528
13.4
1250
5000
258.594
0.071
20.875
539.13
83.565
32 - 1kHz
74
0.1674
176
1.5
1.5
40
4
3.545x3.545
11.26
XTRPRO102D
39.3
0.634
17.952
9.776
0.407
0.391
3.4
4
2.293
87.8
90.8
0.472
12
900
3600
173.461
0.094
19.479
366.44
56.798
35 - 1kHz
97
0.1204
Driver Physical Dimension
3
2.659x2.659
11.19
133
0.75
0.75
44
15
Specifications are subject to change without notice
Model/Part Number
Fs (free-air resonance, Hz)
Vas (equivalent compliance, cu. ft.)
Vas (equivalent compliance, liters)
Qms (Q, mechanical)
Qes (Q, electrical)
Qts (total driver Q)
Re (DC resistance, ohms)
Z (nominal impedance, ohms)
Le (inductance, mh)
Efficiency (1W @ 1M, dB)
Efficiency (2.86V @ 1M, dB)
Xmax (one way linear excursion, in.)
Xmax (one way linear excursion, mm)
RMS Power Watts
Nominal Power Watts
MAX Music Power Watts*
Mms (total moving mass, grams)
Cms (mechanical compliance, mm/N)
Bl (motor strength, Tesla-M)
Sd (effective radiating area, sq. cm.)
Sd (effective radiating area, sq. in.)
Frequency range (Hz)
Energy Bandwidth Product (EBP)**
Speaker Displacement (cu ft)
Mounting hole diameter (inches/mm) 13.35 / 339 16.61 / 422 16.61 / 422
Mounting depth (inches/mm) 7.70 / 196 9.59 / 244 9.59 / 244
Magnet Weight (Oz)
Basket diameter (inches/mm)
Typical sealed enclosure (cu. ft.)
Vented enclosure (cu. ft.)***
Port tuning frequency (Hz)
Port diameter (inside,inches)
Port square equivalent (inches)
Port length (inches)
2500 3600 3600
XTRPRO152D XTRPRO154D
34.9 29.1 31.6
XTRPRO124D
Thiele/Small Parameters
3.249 2.589
38.123 92.002 73.308
1.346
11.35 9.271
0.433 0.399 0.471
11.337
0.385 0.448
6.8 3.4 6.8
0.417
48
3.723 2.449 3.752
8
90.9 90.5
89.3 93.9 90.5
89.3
0.528 0.528
13.4 13.4 13.4
0.528
1800 1800
5000 7200 7200
1250
352.038 375.719
0.093 0.085 0.067
223.823
24.56 33.512
539.13 876.16 876.16
28.453
81
135.805 135.805
32 - 1kHz 28 - 1kHz 28 - 1kHz
83.565
1.5 2 2
373 373176
40 36 36
1.5
11.26
44
3.545x3.545 3.545x3.545 3.545x3.545
4
5.42 5.42
33
73 67
0.2703
Driver Physical Dimension
Recommended Enclosures
3072.04761.0
SPECIFICATIONS
17
Explanation of Enclosure Specifications
There are many different factors that help determine the best style of enclosure for
you or your vehicle. Listed below are some factors that should be considered.
The size of the enclosure is directly proportional to the efficiency and power handling
of that speaker. A woofer in a smaller enclosure will handle more power than the
same woofer in a larger enclosure. The exact opposite is true for efficiency, a larger
enclosure will play lower frequencies at a louder volume with less power than a
smaller enclosure.
The following will explain differences in sealed enclosures. A large enclosure is
best suited if you have smaller amounts of power (25% to 50% of speaker’s power
handling), have a larger vehicle or looking for greater output. While the smaller
enclosure should be utilized if you have recommended power (50% to 100% of
speaker’s rated power handling), have a smaller (high gain) vehicle or are looking for
more accurate sound reproduction. A smaller sealed enclosure will yield more control,
this audible translates into faster and more accurate bass.
A vented enclosure will offer greater efficiency and stronger low bass output compared
to a sealed design. A vented enclosure uses the back wave (sound from the back side
of the cone) to reinforce the output from the speaker. A properly tuned enclosure will
yield gain across the entire bandwidth of the subwoofer system and offer more cone
control than a sealed enclosure. A low tuning will yield less overall gain but greater
extension (low bass). A high tuned enclosure will offer more gain but limit the low
end response of the system. One of the advantages of having a vented enclosure is
because it is tunable to a specific frequency and that tuning frequency is known as the
“Fb”. Another important box specification is “F3”, which is the roll-off frequency at
which the driver's response is down -3dB. This is an important number when it comes
to setting your high-pass filter or your ORION Intelli-Q. The Intelli-Q should be set at
the same frequency as the “F3”as this will keep the speaker from damaging or what
is know as over-loading.
18
ENCLOSURE RECOMMENDATIONS
Enclosure Details
1. External dimensions calculated for 3/4” building material
2. Includes speaker displacement
3. Volumes given are net tuning volume
4. Enclosures include a minimal amount of damping material. Just enough material to
line the inside of the enclosure is required.
XTRPRO102 & 104 Sealed Enclosure Recommendations
Box
Properties
— Description
—
Type:
Closed
Box
Shape: Prism,
Square
— Box Parameters
—
Vb = 0.75
cu.ft
V(total) = 0.791
cu.ft
Qtc =
0.598
QL =
7
F3 = 50.61
Hz
Fill =
none
External
Dimensions
A = 12 in. (305
mm)
B = 15.5 in. (394
mm)
C = 10.8 in. (274
mm)
Internal
Dimensions
A = 10.5 in. (267
mm)
A
B = 14 in. (356
mm)
C = 9.3 in. (236
mm)
C
Wall
Thickness
Front = 0.75 in. (19
mm)
B Side = 0.75 in. (19
mm)
c
To p
&
Bottom
b
d
Front
&
a
Back
c
Sides
—Box
Parts—
Box Shape: Square
Prism
1Top,1
Bottom:
depth (c) = 10.8 in. (274
mm)
width (b) = 15.5 in. (394
mm)
thickness = 0.75 in. (19
mm)
1 Front, 1
Back:
height (a) = 10.5 in. (267
mm)
width (d) = 14 in. (356
mm)
thickness = 0.75 in. (19
mm)
2 Sides: height (a) = 10.5 in. (267
mm)
depth (c) = 10.8 in. (274
mm)
thickness = 0.75 in. (19
mm)
Figure
14
Figura
14
Abbildung
14
—Driver
Mounting—
Mounting:
Front
19
XTRPRO102 & 104 Vented Enclosure Recommendations
Box
Properties
— Description
—
Type:
Vented
Box
Shape: Prism,
Square
— Box Parameters
—
Vb = 0.75
cu.ft
V(total) = 0.841
cu.ft
Fb = 44
Hz
QL =
7
F3 = 35.24
Hz
Fill =
none
— Vents
—
No. of Vents =
1
Vent shape =
round
Vent ends = one
flush
Dv = 3 in. (76
mm)
Lv = 11.19 in. (284
mm)
Figure
15
Figura
15
Abbildung
15
A
B
External
Dimensions
A = 12 in. (305
mm)
B = 15.5 in. (394
mm)
C = 11.39 in. (289
mm)
Internal
Dimensions
A = 10.5 in. (267
mm)
B = 14 in. (356
mm)
C = 9.89 in. (251
mm)
C
Wall
Thickness
Front = 0.75 in. (19
mm)
Side = 0.75 in. (19
mm)
c
To p
&
Bottom
b
d
Front
&
a
Back
h
e
c
Sides
g
—Box
Parts—
Box Shape: Square
Prism
1Top,1
Bottom:
depth (c) = 11.39 in. (289
mm)
width (b) = 15.5 in. (394
mm)
thickness = 0.75 in. (19
mm)
1 Front, 1
Back:
height (a) = 10.5 in. (267
mm)
width (d) = 14 in. (356
mm)
thickness = 0.75 in. (19
mm)
height (a) = 10.5 in. (267
mm)
depth (c) = 11.39 in. (289
mm)
thickness = 0.75 in. (19
mm)
—Driver
Mounting—
Mounting:
Front
Vent
Parts
1
Duct:
outside diameter (e) = 3.25 in. (83
mm)
inside diameter (g) = 3 in. (76
mm)
length (h) = 11.19 in. (284
mm)
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
