Sunjoy G-GZ088PST Owner's manual

Brand
Sunjoy
Model
G-GZ088PST
Type
Owner's manual

Sunjoy G-GZ088PST is a Column Deluxe Gazebo, designed for leisure use and providing shade from the sun. It is not meant to withstand inclement weather, including high winds, rain, and snow. The gazebo's fabric is water-resistant but not waterproof and may leak during precipitation. The gazebo should be set up in an ideal location, at least 6 feet from any obstruction, and on a clear and level surface. It is not recommended to permanently stake or attach the gazebo to a concrete floor or platform. Assembly requires at least two people and some tools, including a ladder and a wrench.

Sunjoy G-GZ088PST is a Column Deluxe Gazebo, designed for leisure use and providing shade from the sun. It is not meant to withstand inclement weather, including high winds, rain, and snow. The gazebo's fabric is water-resistant but not waterproof and may leak during precipitation. The gazebo should be set up in an ideal location, at least 6 feet from any obstruction, and on a clear and level surface. It is not recommended to permanently stake or attach the gazebo to a concrete floor or platform. Assembly requires at least two people and some tools, including a ladder and a wrench.

Owner’s manual
Assembly Instruction: COLUMN DELUXE GAZEBO
G-GZ088PST
Safety Warning and Precautions
Note: This gazebo is meant to be used for decorative and sunshade purposes only and is not
meant to withstand all inclement weather including high winds, rain and snow.
Please read drawings carefully before assembling
1) Do not cook underneath gazebo.
2) Do not ignite fireworks underneath gazebo. Keep all flame and heat sources away from
tent material. Gazebo fabric meets CPAI-84 specifications for flame resistance, but is
not fire proof. The fabric will burn if left in continuous contact with any flame source.
The application of any foreign substance to the tent fabric may render the
flame-resistant properties ineffective.
3) This product is designed for leisure use only and is not a shelter against adverse
weather conditions.
4) Gazebo fabric is water resistant, not water proof and may leak during exposure to precipitation.
5) Please keep the parts list, it could be useful to reorder some parts for service if
necessary.
When assembling and using this product, basic safety precautions should always be followed to
reduce the risk of personal injury and damage to equipment. Please read all instructions before
assembly and use
1. Select ideal location. It’s for outdoor use only! Begin assembly not less than 6 feet from any obstruction
such as fence, garage, house, overhanging branches, laundry line or electrical wires. Set out all parts on a
clear and level surface prior to assembly. This gazebo cannot be permanently staked or attached to concrete
floor or platform. Ideally, the gazebo should be set up in its desired location to avoid moving it after assembly.
2. Use caution. During all the process of assembling, especially when lifting heavy or large parts, pay attention
to safety. THIS UNIT IS HEAVY! Some parts may contain sharp edges, wear protective gloves if necessary.
At least two or more people are recommended for safe assembly.
3. Tools and Assistance. Ladder and wrench are self-provided. Whenever possible, assistance is preferred.
4. Check for parts available. Before assembling your gazebo, be sure that you have all parts described in the
Parts List.
5. Check for damaged parts. Before assembling your Pavilion Frame, check for damaged parts, any part
that appear damaged should be carefully checked to determine that it will be operated properly and perform
its intended function. Any part that is damaged should be properly repaired by a qualified technician or ask
for a replacement.
6. Refer to assembly diagram. During assembly, it will be helpful to referring to the assembly diagram.
7. Keep children away. Children must never be allowed in the work area. Do not let them handle parts and
tools. No people will be permitted to enter into work area except who is working. Keep all children and
pets away from assembly area.
8. Caution for paint: Keep paint away from fire and high temperature. Store it in cool and gloomy place.
2. ASSEMBLY INSTRUCTION
2.1 Part list:
No
Part
Photo
Qty
A
Column
4
B
Long Rail
2
C
Short Rail
2
D
Corner Connector (Left)
2
E
Corner Connector (Right)
2
F
Support Connector
4
G
Short Support Pole
4
H
Long Support Pole
4
I
Long Mosquito Net Pole
4
J
Short Mosquito Net Pole
4
K
Top Support Pole
1
L
4-way Fitting
2
M
Middle Connector
1
N
Extreme Top Support
Pole
4
O
Extreme Top Pole
1
P
3-way Fitting
2
Q
Top Arrow
2
R
Bolt M6*35
(TBZ0030635HQ)
4
S
Bolt M6*10
(TBZ0030610HQ)
24
T
Nut M6
(TBZ20106HQ)
4
U
Bolt M6*15
(TBZ0030615HQ)
16
V
Stake
16
W1
Big Canopy
1
W2
Small Canopy
1
X1
Mosquito Net
1
X2
Mosquito Net Hook (40pcs
shall be assembled in
mosquito net X1, 4pcs spare)
44
Y
Wrench
1
Z
Snap (25pcs pre assembled
in G,H,K,N,O; 2pcs spare)
27
Z1
Paint Bottle
1
2.2 Assembly:
(Tools required for assembly: a screwdriver)
Assembly for Frame
Step 1. Connect long rail (B) and corner connector (D or E) by bolt(S) as Fig. 1-1. Connect short rail(C) and the
other one end of corner connector (D or E) by bolt(S) as Fig.1-2; Repeat this procedure to form a 10’ x12’ oblong.
--- Be sure that the pre drilled hole in rail (B, C) have to be upper after assembly.
Step 2. Connect one end of mosquito net pole (I or J) on corner connector (D or E) by bolt (S) as Fig. 2-1.
Connect the other one end of mosquito net pole (I or J), support connector (F) and rail (B or C) by bolt (U) as Fig
2-2.
Step 3. Connect top support pole (K), 4-way fitting (L) and middle connector (M) as Fig.3-1 shown.
Insert short support pole (G) into 4-way fitting (L) and middle connector (M), and insert long support pole (H) into
4-way fitting (L) as Fig. 3-2 shown. Now, the top frame is got ready.
Then assemble top frame to completed oblong frame in Step. 2.
Insert long support pole (H) to corner connector (D or E) as Fig. 3-3 shown,
And Insert short support pole (G) to support connector (F) as Fig. 3-4 shown.
Put big canopy (W1) over the top frame. --- Do not expand it because it will affect the assembly for extreme top.
Step 4. Inert extreme top support pole (N) and extreme top pole (O) to 3-way fitting (P) as shown in Fig 4-1. Now,
extreme top frame is got ready. Put small canopy (W2) over the extreme top frame. And put the welded bolt on
3-way fitting (P) through into the pre drilled hole in small canopy (W2). Tighten small canopy (W2), fit 4 corners to
the end of extreme top support pole (K). And screw top arrow (Q) to the welded bolt on 3-way fitting (P) <Fig.
4-1>; Then assemble extreme top to big top. Attach extreme top support pole (N) to long support pole (H), fasten
by bolt (R) and nut (T) as Fig. 4-2. Tighten all hardware by screwdriver and wrench (Y). --- Do not overtighten.
Now, the top is got ready.
Step 5. Put big canopy (W1) over the top frame --- Do not tighten. . Raise completed top up. Assemble column
(A) to corner connector (D or E), fasten using bolts (U) as Fig. 5-1. Finally, Tighten big canopy (W1) and fit the
rim surround rail. Tighten all hardware by screwdriver --- Do not overtighten.
Warning: This procedure must ask four helpers (at least 5 adults) to do following procedure together;
do not attempt to assemble it alone.
Step 6. Secure the gazebo to the ground with stake (V) as Fig. 6-1.
Step 7 Assemble mosquito net to gazebo. Expand mosquito net (X1). Long side to long mosquito net pole(I),
short side to short mosquito net pole (J), zipper in middle. Then, hang mosquito net hook(X2) to mosquito net
pole (I, J). Attach mosquito net band to column (A).
Now, your gazebo is ready for use.
IMPORTANT:
MANUFACTURER’S LIMITED WARRANTY: This product is warranted for a period of six (6)
months against manufacturer defects. This warranty is limited to repair or replacement of the
product as deemed necessary by the manufacturer or its agents. No ancillary damages resulting
from such defects are covered by this warranty.
Maintenance
Our iron components for garden accessories and furniture are coated with rust inhibiting paint that
protects it from rusting. However, due to the nature of iron, surface oxidation (rusting) will occur
once these protective coatings are scratched. This is a natural process and is not a defect! To
minimize this condition, we recommend care when assembling & handling the product to prevent
scratching the paint. Should any scratching or damage occur, we recommend immediate touch-up
with rust inhibiting paint, which is included in the package. Surface rust can also be easily removed
with a very light application of common cooking oil. If surface oxidation (rusting) occurs and if no
measure is taken to prevent this, the oxidation may start dripping on to deck or patio and cause
damaging stains, which may be difficult to remove. This can be prevented if measure is taken to
keep the product from oxidizing.
Please do not return this product to the store. For expedited replacement parts order, fax the attached completed
customer service replacement form to 740 283 3549. Or send via e-mail at rona06@sunjoygroup.com . Or for
technical assistance call US toll free at (866) 578-6569 from 8:30am to 5:30pm EST.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Sunjoy G-GZ088PST Owner's manual

Brand
Sunjoy
Model
G-GZ088PST
Type
Owner's manual

Sunjoy G-GZ088PST is a Column Deluxe Gazebo, designed for leisure use and providing shade from the sun. It is not meant to withstand inclement weather, including high winds, rain, and snow. The gazebo's fabric is water-resistant but not waterproof and may leak during precipitation. The gazebo should be set up in an ideal location, at least 6 feet from any obstruction, and on a clear and level surface. It is not recommended to permanently stake or attach the gazebo to a concrete floor or platform. Assembly requires at least two people and some tools, including a ladder and a wrench.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents