Mortara Instrument Quinton Q-Stress 4.5 Installation Instructions Manual

Brand: Mortara Instrument

Model: Quinton Q-Stress 4.5

Type: Installation Instructions Manual

Q-Stress 4.5

System Installation Instructions

REF: 70-00261-02 Rev D1

Contents

3epocS

4snoitcennoc erawdraH

7trac sserts a no noitallatsni metsyS

8thgieh ecafrus pot fo tnemtsujdA

Install the writing surface and paper tray 10

11tnemecalp tnenopmoC

71eciveD esicrexE eht tcennoC

Mortara Instrument, Inc. 7865 North 86th Street, Milwaukee, WI 53224 U.S.A. • Tel: 1.800.231.7437 • Fax: 1.414.354.4760 • Website: www.mortara.com

Technical Support: Tel: 1.888.667.8272 • Email: techsupport@mortara.com

Manufactured By: Mortara Instrument, Inc.

Mortara, Q-Exchange, and Quinton

are trademarks of Mortara Instrument, Inc.

Information in this document is subject to change without notice. Names and data used in

the examples are ﬁctitious unless otherwise noted.

CE Mark Declaration

e CE marking of conformity indicates that the device having this symbol on its

immediate label meets the applicable requirements of the European Medical Device

Directive.

Trademark Information

Quinton, Burdick, HeartCentrix‚ Q-Stress, and HeartStride are trademarks or registered

trademarks of Mortara Instrument, Inc. All other product and company names are trademarks

or registered trademarks of their respective companies.

Scope

is document describes the assembly of a Stress system. It is designed to be used as a

whole for the installation process or in part as a troubleshooting tool for ensuring correct

connection, conﬁguration, and functioning of the Stress system.

Because the Stress system can be purchased in diﬀerent conﬁgurations and with diﬀerent

options, your system’s feature set may be diﬀerent from the feature set shown in this

document.

Read all instructions before you begin the installation process. Follow the instructions in

the order given.

If you have any questions regarding execution of these instructions, contact technical

support at:

1.888.667.8272

techs[email protected]

Q-Stress 4.5 System Installation Instructions

Hardware connections

Caution. The following cautions apply:

The computer, monitor, preamp, and printer must be plugged into the isolation transformer.

The preamp and printer must be plugged into the A outlets and the computer and monitor

(or computer and power strip on units equipped with the optional external hard disk) must

be plugged into the B outlets.

*Connect the optional external hard drive to the Stress system using a power strip. Refer to

the instructions provided with the external hard drive for proper connection.

*Do not plug any other components into the power strip on units equipped with the optional

external hard disk.

The isolation transformer must be plugged into a dedicated circuit.

The treadmill must be plugged into a dedicated circuit.

*You cannot connect both a laser printer and an optional external hard drive on the same

system.

If the preamp is mounted on the treadmill handrail, it should be mounted perpendicular to

the treadmill belt to avoid damaging the unit when the treadmill is inclined.

Use of an uninterruptable power supply (optional)

If you use an uninterruptable power supply (UPS), insert it between the isolation

transformer and the computer and monitor. See the system conﬁguration block diagram

(Figure 1).

WARNING! Electronic interference.

The preamp can be mounted on the treadmill handrail, placed on the oor, or located in

another convenient spot. It should be installed in a location that removes the patient cable

from close proximity to power cords, transformers, or other power lines connected devices

to minimize noise pick-up.

System conguration

e block diagram (Figure 1) shows a typical conﬁguration and suggested locations for

plugging in the various system hardware components. Your system will be similar but may

not be identical to the conﬁguration shown. If you have questions about connecting

components, contact technical support.

WARNING! Electronic interference.

Grounding reliability can be achieved only when equipment is connected to a properly-

grounded receptacle. Ensure that the isolation transformer is connected to this type of

electrical outlet.

Hardware connections

Figure 1: Stress system components

Note: There is a power switch on the front of the computer that must be pressed to boot up

the computer. Turn o the computer by shutting down Windows.

Use the QRS Sync to connect a blood pressure monitor to the system (rather than one of the

Analog Outputs).

Make a note of which ports are used to connect the treadmill, ergometer, and blood pressure

monitor. You will need this information to congure the Stress software.

Attach the service card and plastic sleeve to the video cable using the supplied wire ties.

The HASP® (or dongle) attaches to the computer’s parallel port.

Caution. Improper voltage.

The ergometer exercise device may not be self switching. Refer to the ergometer user guide

for proper voltage adjustment setting.

Computer

Remote

Keypad

(Optional)

Keyboard

Mouse

USB

PS2

Treadmill

USB

RS-232

USB

QRS Synch

Patient

Cable

Power

Data

AC Wall

LCD

Laser Printer

Preamp II

Blood

AC Wall

Outlet Outlet

Pressure

Monitor

Isolation

Transformer

ParallelChart Recorder

USB

COM 1

Preamp II

supply

Power

Uninterruptable

Power Supply

(optional)

Monitor

Caution. Treadmill communication.

Power Management should be disabled for USB ports to prevent USB ports from being

powered down. This is benecial for maintaining communication with the treadmill.

To congure Q-Stress with USB power management disabled, select Power Options, then

Advanced settings, then USB settings and set USB selective suspend setting = Disabled.

Q-Stress 4.5 System Installation Instructions

Computer and Preamp II connections

Port Connect to

1AC Power

2Unused

3Unused

4Keyboard

5Mouse (PS/2)

6USB printer (HP laser printer)

7Parallel printer with HASP (TCR-1000 chart recorder)

8Unused

9COM 1

Blood pressure monitor (optional)

Note: Record connections to COM ports for use in system setup.

10 COM 4 for Preamp II;

11 External hard drive (optional)

12 Network (optional)

13 Monitor

Note: Attach the service card (in plastic sleeve) to video cable.

14 TM-series treadmill

15 Mouse (USB)

16 COM 3

17 QRS Sync

Note: Connect the QRS Sync to the blood pressure monitor, rather

than an Analog Output. See Taking Accurate Blood Pressure

Measurements on page C-1 of the User’s Guide for details.

18 Analog output

19 To computer

20 DC Power

3.4 GHz

Preamp II

16 10

20 17 1819

System installation on a stress cart

The steps below show how to place Stress system components on a Q-Stress cart. If you are

not placing your system on a cart, you can use these steps for instructions on connecting

the different components.

Figure 2: Example of a Q-Stress cart

Caution. Unstable workstation.

For best balance, place the system equipment on the cart as shown in Figure 2.

Q-Stress 4.5 System Installation Instructions

Adjustment of top surface height

Follow the instructions below to change the height of the top surface. Be aware that some

of the screws are located in awkward positions. e pictures below show the top surface

changed from the higher to the lower height.

Step

Remove the monitor mount by

pulling the mount straight up

and then toward you (make sure

you remove the lock bolt rst).

21. Remove the mounting

hardware from the top

surface:

2. Four screws from the monitor

mount

3. Two or three screws

(depending on position of

risers) connecting the risers

to the base (these must be

removed from the inside of

the cart.

Remove the top surface from the

cart

System installation on a stress cart

Turn the top surface over and lay

it on the cart (or a flat area).

Remove the screws connecting

each riser to the top surface

Rotate each riser 90 degrees and

fasten back to the top surface

Turn the top surface so the risers

are on the bottom and lined up

with the holes on top of the cart.

Replace on cart. Reattach the

four screws that hold the

monitor to the cart.

Reattach the screws that hold

the risers to the cart (you will

need to work from under the

cart).

Reattach the monitor holder and

monitor to the cart.

Step

Q-Stress 4.5 System Installation Instructions

Install the writing surface and paper tray

Follow these instructions to install the optional writing surface and chart recorder paper

tray on the Q-Stress cart.

Step

Place the writing surface

brackets into the slots on the

right side of the cart.

Attach the chart recorder paper

tray to the left side of the cart.

Attach the paper tray ush with

the cart for storing.

System installation on a stress cart

Component placement

Follow the instructions below for placement of system equipment.

Note: The equipment for your system may be different from that shown.

Step

Place the strap (found in accessory

box 1) through the holes in the

bottom of the cart.

Place the computer tower through

the strap and on to the cart. Secure

the tower with the strap.

For a laser printer:

On the under side of the printer

place the 4 rubber feet as shown.

Q-Stress 4.5 System Installation Instructions

Place the laser printer or chart

recorder on top of the cart.

Note:Follow printer manufacturer’s

instructions to set up the printer.

Plug the four component AC power

cables into the transformer.

(SeeFigure 1 on page 5 for

appropriate plug placement.)

While holding the four AC cables,

place the transformer on the

bottom of the cart.

7Connect an AC cable to the

transformer.

Connect the third standard length

AC cable to the computer tower.

Connect the longest AC cable to the

pre-amp.

Route the two of the standard

length AC cables to the top of the

cart for the monitor and chart

recorder.

Note:Make sure the preamp is 3

feet or farther away from the

isolation transformer. Electro-

magnetic interference could cause

noisy ECG signals.

Step

System installation on a stress cart

Depending on the type of printer:

•Connect the USB cable and the

power cord to the printer.

•Connect the parallel cable to the

chart recorder.

Route and connect the printer cable

to the upper left USB port on the

computer. Also plug the video

monitor into the video port.

Step

Keyboard

Video

HASP

Mouse

Treadmill

Printer

Blood

monitor

(optional)

pressure

Q-Stress 4.5 System Installation Instructions

Route the mouse and keyboard

cables through the hole on the top

of the cart; through the hole in the

shelf below and plug into the

computer.

Place the monitor face down on a

soft, clean, at surface. Attach the

universal bracket to the rear of the

monitor. Tighten the screws

securely.

Caution! Be careful not to scratch or

damage the LCD screen.

Route the monitor video and power

cables through the monitor post up

through the cable hole.

Step

Attach bracket to back of monitor here

System installation on a stress cart

Place the monitor arm on the cart

and engage the hooks.

Caution! A minimum of 6 arm hooks

should be engaged.

Step

Q-Stress 4.5 System Installation Instructions

Secure the monitor mounting post

by fastening the security bolt in the

hole that lines up with the pen nut

on the cart. Attach the power and

monitor cables to the monitor.

Connect the preamp interface cable

from the preamp to the high speed

serial port on the computer.

Note:Be sure to use the correct

port.

Install the preamp using the

instructions provided with the

preamp.

The hardware assembly and

connection is now complete.

See Connect the Exercise Deviceon

page 17 for directions to attach a

treadmill or ergometer.

Step

Use this port

Connect the Exercise Device

Treadmill

Connect the treadmill to the computer via the USB cable provided. No further

preparation is needed.

Ergometer

Use the instructions that came with your exercise device to connect it to the Stress

computer.

Install Software

See Q-Stress 4.5 Software Installation and Upgrade Instructions (70-00260-02) to install the

Stress application and supporting software and conﬁgure the operating system.

Mortara Instrument, Inc. 7865 North 86th Street, Milwaukee, WI 53224 U.S.A. • Tel: 1.800.231.7437 • Fax: 1.414.354.4760 • Website: www.mortara.com

Technical Support: Tel: 1.888.667.8272 • Email: [email protected]

Manufactured By: Mortara Instrument, Inc.

Mortara, Quinton, and Q-Exchange

are trademarks of Mortara Instrument, Inc.

Mortara Instrument Quinton Q-Stress 4.5 Installation Instructions Manual

Brand: Mortara Instrument

Model: Quinton Q-Stress 4.5

Type: Installation Instructions Manual

Download PDF

report

Mortara Instrument Quinton Q-Stress 4.5 Installation Instructions Manual

Mortara Instrument Quinton Q-Stress 4.5 Installation Instructions Manual

Other documents