Elektron MULTIMIG 200 Operating instructions

Made in Germany

Operation Manual

MULTIMIG 200

MIG / MAG - Welding machine

Item-No: 327 973

Revision: 1.0 - Original

Version: 31.01.2013

Be sure you have read and understood this operating

manual before you carry out any works on and/or with this

equipment!

2

Branch Bremen

Hinterm Sielhof 22

D-28277 Bremen

Germany

Phone: +49 (0)421 / 54 90 6 - 906

Fax: +49 (0)421 / 54 90 6 - 19

E-Mail: vertrieb@elektron-bremen.de

Internet: www.elektron-bremen.de

Release:

BlitzRotary GmbH Branch Bremen

MULTIMIG 200

Table of contents

3

Table of contents

1

Machine elements 4

2

Explanation of symbols 5

2.1

Meaning of the symbols in the operation

manual 5

2.2

Meaning of the symbols on the machine 5

3

Safety precautions 5

4

General regulation of use 6

5

Unit protection 6

6

Noise emission 6

7

Ambient conditions 7

8

UVV inspection 7

9

Electromagnetic compatibility

(EMC) 7

10

Setup and transport 8

11

Brief operating instructions 9

12

Before start-up 10

12.1

Connecting the torch 10

12.2

Connecting the ground cable 10

12.3

Fastening the ground clamp 10

12.4

Insert the welding wire spool 11

12.5

Thread the wire electrode in 11

12.6

Connecting the inert gas cylinder 12

12.7

Changing the wire electrode 12

13

Start-up 14

13.1

Control console MULTIMIG 200 14

13.2

Start-up 15

13.3

Current / voltage display 16

13.4

Torch with remote control 16

13.5

Deactivate operation mode 16

13.6

Characteristic line 17

13.7

Mode Manual 17

13.8

Secondary parameters 17

13.9

Tiptronic 18

13.10

Special functions 21

13.11

Reset setting 21

14

Menu structure 23

15

Messages 25

16

Troubleshooting 26

17

Repair and maintenance 28

17.1

Check regularly 28

17.2

Torch care 28

18

Technical data 29

19

Options and accessories 30

19.1

torch holder 30

20

Disposal 30

21

Service 30

22

Schematic 31

MULTIMIG 200

Machine elements

4

1 Machine elements

Fig. 1: Machine elements

1 Safety chain for gas

2 Hoisting points

3 Mains cable

5 Gas hose

6 Tray area

7 Handle

8 Control panel

9 Main switch

10 Socket for ground cable

11 Central socket

Some depicted or described acces-

sories are not included in the scope

of delivery.

Subject to change.

MULTIMIG 200

Explantion of symbols – Safety precautions

5

2 Explanation of symbols

2.1 Meaning of the symbols in the

operation manual

Danger to life and limb!

If the danger warnings are disre-

garded, this can cause slight or

severe injuries or even death.

Danger of property damage!

Disregarding danger warnings can

cause damage to work pieces,

tools, and equipment.

General note!

Designates useful information

about the product and equipment.

2.2 Meaning of the symbols on the

machine

Danger!

Read the user information in the

operation manual.

Disconnect the mains plug!

Pull out the mains plug before

opening the housing.

3 Safety precautions

Hazard-free working with the ma-

chine is only possible if you read

the operating and safety instruc-

tions completely and strictly ob-

serve them.

Please obtain practical training be-

fore using the machine for the first

time. Follow the accident preven-

tion regulations (UVV

1

)).

Before starting any welding work,

clear away any solvents,

degreasing agents, and other

flammable materials from the

working area. Cover flammable

materials which can not be moved.

Only weld if the ambient air

contains no high con

centrations of

dus

t, acid vapours, gases or

flammable substances. Special

care must be taken during repair

work on pipe systems and tanks

which contain or have con

tained

flammable liquids or gases.

Never touch live parts inside or

outside of the housing. Never

touch wel

ding electrodes or live

welding current parts in a machine

that is on.

Do not expose the machine to

rain, do not spray water on it or

steam blast it.

Always use a welding shield. Warn

other persons in the welding area

about arc-rays.

Please use a suitable extraction

system for gases and cutting

fumes. Always wear breathing

apparatus whenever there is a

risk of inhaling welding or cutting

vapours.

MULTIMIG 200

General regulation of use

6

If the mains cable is damaged or

severed in use, do not touch the

cable but unplug the mains plug

immediately. Never use a

machine if the mains cable is

damaged.

Keep a fire extinguisher near the

welding area.

Check the welding area for fire af-

ter welding (see UVV

1

)).

Never try to disassemble the pres-

sure reducer. Replace the defec-

tive one.

The machine must be transported

or set up only on firm, level

surfaces. The maximum

admissible angle of inclination for

setting up or transporting is 10°.



Service and repair work may only be carried

out by a trained electrician.



Ensure that the ground cable has good and

direct contact near the welding location. Do

not allow welding current to pass through

chains, ball bearings, steel cables or

grounding equipment; this may melt them.



Secure yourself and the welding machine

when working in elevated or inclined areas.



The machine may only be connected to a

properly grounded mains supply. (Three-

phase four-wire system with grounded

neutral conductor or single phase-three-wire

system with grounded neutral conductor)

socket and extension cable must have a

functional protective conductor.



Wear correct protective clothing, leather

gloves and leather apron.



Protect the welding area with curtains or

mobile screens.



Do not use this machine to thaw frozen

water pipes or cables.



In closed containers, under cramped con-

ditions, and in high electrical risk areas, only

use machines with the S sign.



Switch off the machine during breaks and

close the valve of the gas cylinder.



Secure the gas cylinder with a chain to

prevent it falling over.



Disconnect the mains plug from the mains

before changing the place of installation or

making repairs to the machine.

Please heed the safety regulations which apply

to your country.

Subject to change.

4 General regulation of use

This unit is for welding of steel, aluminium and

their alloys as well as for brazing with CuSi

wires for commercial as well as for industrial

use.

5 Unit protection

This machine is protected electronically

against overloading. Do not use fuses of higher

amperage than printed on the identification

plate.

Close the side cover before starting any

welding work.

6 Noise emission

The noise level of the unit is less than

70 dB(A), measured under standard load in ac-

cordance with EN 60974-1 in the maximum

working point.

MULTIMIG 200

Electromagnetic compatibility (EMC)

7

7 Ambient conditions

Temperature range of ambient air:

In operation:

-10 °C … +40 °C (+14 °F … +104 °F)

Transport and storage:

-25 °C … +55 °C (-13 °F … +131 °F)

Relative humidity:

up to 50 % at 40 °C (104 °F)

up to 90 % at 20 °C (68 °F)

-25 °C … +55 °C (-13 °F … +131 °F)

Opera

tion, storage and transport

may only be carries out within the

ranges indicated! Use outside of

this range is considered not used

with its intended purpose. The

manufacturer is not liable for dam-

ages cause by misuse.

Ambient air must be free of dust, acids, cor-

rosive gases or other damaging substances!

8 UVV inspection

Operators of commercially-operated welding

systems are obliged to have safety inspections

of the equipment carried out regularly in

accordance with VDE 0544-4. ELEKTRON

recommends inspection intervals of 12 months.

A safety inspection must also be carried out

after alterations or repair of the system.

Improper UVV inspections can

destroy the system.

9 Electromagnetic compatibility

(EMC)

This product is manufactured in conformance

with the current EMC standard. Please note

the following:



The machine is intended for welding in both

commercial and industrial applications

(CISPR 11 class A). Use in other

surroundings (for example in residential

areas) may disturb other electronic devices.



Electromagnetic problems during start-up

can arise in:

• Mains cables, control cables, signal and

telecommunication lines near the welding or

cutting area

• TVs / radios

• Computers and other control equipment

• Protection equipment such as alarm

systems

• Pacemakers and hearing aids

• Equipment for measurement and calibration

• Equipment with too little protection against

disturbances

If other equipment is disturbed it may be

necessary to provide additional shielding.



The affected area can be bigger than your

premises/property. This depends on the

building, etc.

Please use the machine in compliance with the

manufacturer's instructions. The machine

operator is responsible for installation and use

of the machine. Furthermore, the owner is

responsible for eliminating the disturbances

caused by electromagnetic fields.

MULTIMIG 200

Setup and transport

8

10 Set-up and transport

Danger of injury due to the de-

vice falling over and crashing!

When transporting using mechani-

cal lifting equipment (e.g. crane,

etc.), only the hoisting points shown

here may be used. Use suitable

load-carrying equipment.

Each lifting point must be loaded

separately. Do NOT,

for example

put one load strap through both

handles, as this could lead them to

be pulled together and cause

breakage!

Do not use a fork-lift truck or simi

lar

device to lift the machine by its

housing.

Remove the gas cylinder from the

welding machine before transpor-

tation.

The machine must be transported

or set up only on firm, level sur-

faces. The maximum admissible

angle of inclination for

setting up or

transporting is 10°.

Fig. 2: Lifting point for 4-point hoisting

MULTIMIG 200

Brief operating instructions

9

11 Brief operating instructions

A detailed description can be found

in chapter. „Before start-

up“ Page

10 and chapter. „Start-up“ Page 14.

 Place the inert gas cylinder on the unit and

secure it with the chain 1.

 Remove the screw cap from the inert gas

cylinder and open the valve 32 briefly (blow-

out).

 Connect the pressure reducer 13 to the inert

gas cylinder.

 Connect the insert gas hose 5 from the unit

to the pressure reducer and open the

cylinder valve.

 Insert the mains plug in the socket.

 Connect welding return cable to connector

10 and the clamp to the workpiece.

 Insert wire feed rollers 25 into wire feed unit

in accordance with the type of welding wire

selected, set contact pressure to 2.

 Connect the torch to central connector 11

and insert the relevant contact tip to se-

lected welding wire.

 Insert welding wire.

 Keep torch switch pressed and set main

switch 9 ON. Magnetic valve will be ac-

tivated!

 Adjust gas quantity at pressure reducer.

(Rule: wire diameter x 10 = gas quantity).

 Hold down the wire feed switch 29 until the

welding wire projects from the torch neck to

the gas nozzle by approx. 20 mm.

 Mode key 47 for selection of 2-stroke mode.

 Key characteristics 50 and operation knob

52 for adjusting the selected characteristic

line (material-gas-wire-combination).

 Turn knob 45 to set material thickness of

the weldable material.

 Torch switch pressed and held = welding.

 Release the torch switch = welding process

completed.

MULTIMIG 200

Before start-up

10

12 Before start-up

12.1 Connecting the torch

 Connect the central connector 17 of the

torch to the central socket 11.

Fig. 3: Connecting the torch

12.2 Connecting the ground cable

 Connect welding return cable 18 to con-

nector 10 and secure it by turning it clock-

wise.

Fig. 4: Connecting the ground cable

12.3 Fastening the ground clamp

Fig. 5: Correct

 Attach the ground clamp immediately be-

side the welding point so that the welding

current will not try to find its own return path

through machine parts, ball bearings or

electric circuits.

 Connect the ground clamp firmly to the

welding bench or the workpiece.

Fig. 6: Incorrect



Do not place the ground clamp on the

welding machine or the gas cylinder; oth-

erwise the welding current will be carried via

the protective conductors and it will destroy

these.

MULTIMIG 200

Before start-up

11

12.4 Insert the welding wire spool

Danger to life and limb and fire

hazard due to glowing welding

wire or parts!

A protruding piece of wire out of the

wire s

pool can cause short circuits

to the side panel or bottom of the

unit.

When inserting the welding wire

spool, please pay attention to the

correct winding and make sure that

there are no protruding pieces of

wire.

Set the wire brake in such a way

that the wire spool doesn’t con

tinue

running when releasing the torch

key.

 Open side panel and turn the retaining nut

20 off from the wire spool holder 22.

 Place the welding wire reel on the decoiler

mandrel and ensure that the carrier mandrel

23 locks in position.

 For small welding wire reels, use an adaptor

(order number: 420 922).

 Set the wire brake 21 so that, when the

torch switch is released, the welding wire

spool just does not run on.

Fig. 7: Decoiler mandrel

12.5 Thread the wire electrode in

 Unscrew the contact tip of the torch.

 Open side panel.

 The diameter of the wire electrode must

agree with the legible embossed figure on

the wire feed rollers 25.

 Swing the tilt levers 27 to the side and

thread the wire electrode through the inlet

nozzle 26 and central socket 11.

Fig. 8: open 4-roll wire feed

 Swing the lever back 28 and secure in po-

sition with the tilt levers 27.

Fig. 9: close 4-roll feed

 Turn on the machine at mains switch 9.

MULTIMIG 200

Before start-up

12

Fig. 10: Wire feed button

 Press wire feed button 29.

 Adjust the contact pressure using the reg-

ulation screws 27 so that wire feed rollers

25 just slip when the welding wire spool is

stopped. The wire must not be jammed or

deformed.

A B C

Correct

Contact pressure

too high

Wrong wire feed

roller

Fig. 11: Wire feed rollers

Note for wire feed unit with 4 rollers:

 Adjust the contact pressure of the wire feed

rollers 25 on the side of the inlet nozzle 26

to be less than on the side of the central

socket 11 in order to keep the wire

electrode under tension in the wire feed

unit.

 Push the wire feed button 29 until the wire

protrudes from the torch neck by about

20 mm.

 Screw the contact tip matching the wire

thickness into the torch and cut off the

protruding end of the wire.

12.6 Connecting the inert gas cylinder

 Set the insert gas cylinder 14 down on the

carrier plate and secure it with the chain 1.

 Briefly open the gas cylinder valve 32

several times in order to blow out any dirt

particles present.

 Connect the pressure reducer 13 to the inert

gas cylinder 14.

 Screw the inert gas hose 5 to the pressure

reducer.

 Open valve 32 of shielding gas bottle 14.

 Turn the machine off at main switch 9.

 Press torch key and keep it pressed.

 Turn on the machine at mains switch 9.







Solenoid valve will be switched on for 10

seconds.

 Set the gas quantity using adjusting screw

35 of the pressure reducer 13. The gas

quantity will be displayed on the flowmeter

34.

Rule of thumb:

Gas volume = wire diameter x 10 l/min.



The cylinder content is indicated on the

content manometer 33.

Fig. 12: Connecting the inert gas cylinder

12.7 Changing the wire electrode

MULTIMIG 200

Before start-up

13

 Change the wire feed rollers. Select the

most suitable rollers for the application.

Fig. 13: Wire feed rollers

A Steel feed roller

B Aluminium feed roller

C Knurled feed roller (for flux-cored wire)

Fig. 14: Marking of wire feed rollers

 Replace the steel torch with an appropriate

torch, or change the wire feed spiral.

Wire feed spiral: (for steel or flux-cored

wire)

 Remove the existing wire feed spiral or

plastic core and insert the new wire feed

spiral. (Refer to the operating manual for the

torch)

 Insert the guide tube 85 into the central

connection.

Plastic core: (for aluminium, stainless steel

or CuSi wire)

 Remove the existing wire feed spiral or

plastic core and insert the new plastic core.

(Refer to the operating manual for the torch)

 Remove the guide tube 85 from the central

connection.

 Shorten the protruding plastic core so that it

is tight up against the wire feed roller, and

slide the appropriately shortened support

tube over the protruding plastic core for

stabilisation.

All:

 Tighten the torch and thread the wire elec-

trode in.

The order numbers of the replace-

ment parts depend upon the type of

torch used and the diameter of the

wire, and can be obtained from

the

torch spares lists.

Fig. 15: Wire feed

7 Central socket

17 Central connection (torch)

25 Wire feed roller

38 Retaining nipple (=clamp) of the plastic

liner for 4.0 mm and 4.7 mm outside

diameter

39 O-ring

40 Union nut

41 Plastic liner

42 Support tube for plastic cores with 4 mm

OD Support tube not required with OD of

4.7 mm.

43 Guide tube

44 Wire feed spiral

MULTIMIG 200

Start-up

14

13 Start-up

13.1 Control console MULTIMIG 200

Fig. 16: Control console MULTIMIG 200

Fig. 17: Graphic display

MULTIMIG 200

Start-up

15

9 Main switch for turning the welding

machine ON and OFF.

45 Turning knob for setting material

thickness/welding voltage/welding step.

46 Key button secondary parameter to

access the secondary parameter menu.

When within this menu this key serves to

end it.

47 Trigger Mode to select 2-stroke, 4-stroke,

spot welding or interval mode.

48 Key button menu to access the main

menu. Pressing this key will move one

level back.

49 Graphic display displays all information in

clear text.

50 Key Tiptronic/characteristics direct access

to the Tiptronic menu alt. characteristics

menu (if Tiptronic is switched off).

51 Key Secondary parameter access the

secondary parameter directly. Within the

menu press this key to end menu.

52 Operation knob Menu Turning knob wire

feed serves to:

• select menu (turn)

• confirm menu option (press)

• setting wire feed

• setting secondary parameter

55 Display mode displays the selected mode

by symbol.

56 Display characteristics displays the set

characteristic line.

57 Display Tiptronic-Job if the job no. is

followed by an asterisk (*) on the display,

a min. parameter of a saved job has been

changed.

58 Display wire feed correction displays the

wire feed as correction value differing from

the characteristic line in %.

59 Display wire feed displays the actual wire

feed speed in m/min.

60 Display welding step displays the selected

welding step.

61 Display material thickness displays the

selected material thickness of the

workpiece in mm.

62 Display welding voltage displays the

selected welding voltage in Volt.

13.2 Start-up

 Select with mode key 47 the 2-stroke mode.

 Press key characteristics 50 to enter menu

characteristics.

 Set matching characteristic line (material-

gas-wire combination) by turning operation

knob 52.

 Confirm the characteristic line by pressing

operation knob 52.

 Press operation knob 52 again to end menu

and return to standard display.

 Set the required material thickness alt.

welding step by using turning knob 45.







The machine is ready for welding.



Use operation knob 52 to correct the wire

feed if needed.

MULTIMIG 200

Start-up

16

13.3 Current / voltage display

The actual values of welding voltage and

welding current are displayed during and after

welding (hold function).

These values can be displayed individually or

together on the graphic display.

Possible display:



Welding voltage and welding current



Welding voltage



Welding current

Fig. 18: Display mode

Change of display modern

 Press menu key 48.

 Select menu option „Display mode“ by

pressing operation knob 52.

 Confirm menu option „Display mode“ by

pressing operation knob 52.

 Set the desired display mode by turning

operation knob 52.

 Confirm the desired display by pressing

operation knob 52.







For about 2 seconds a preview of the dis-

play will be shown if the display mode has

been changed.

13.4 Torch with remote control

Fig. 19: Torch PowerMaster

65

Torch display displays the actual welding

step or wire feed speed in Tiptronic mode.

The current job will be displayed.

66 Torch rocker switch Change welding step

and wire feed speed. Between active jobs

can switched over whilst being in Tiptronic

mode.

67 Torch key „Mode“ By pressing (for at least

2 seconds) changeover between Tiptronic

and regular mode will take place. A quick

press in regular mode change between

wire feed, welding step and material

thickness (at selected characteristics).

13.5 Deactivate operation mode

The operation mode spot welding and interval

can be deactivated in the menu and will no

longer be accessable with mode key 47.

 Press key menu 48.

 Set menu to „options“ by turning operation

knob 52.

 Confirm menu „options“ by pressing op-

eration knob 52.

 Set the menu option „interval welding“ or

„spot welding“ by turning operation knob 52

for deactivation.

 Confirm the menu option by pressing opera-

tion knob 52.

 Select and confirm the menu option „off“ by

using operation knob 52.

MULTIMIG 200

Start-up

17

Fig. 20: Interval-welding deactivated

 Press key 46, 50 or 51 to end menu and

return to standard display.

13.6 Characteristic line

Select characteristic line

 Press key menu 48.

 Set menu option „characteristic line“ by

turning operation knob 52.

 Confirm menu option „characteristic line“ by

pressing operation knob 52.

 Set required characteristic line by turning

operation knob 52.

 Confirm characteristic line by pressing op-

eration knob 52.

Fig. 21: Characteristics

 Press key 46, 50 or 51 to exit menu and

return to standard display.







If the graphic display shows „noP“ (no pro-

gram) for material thickness, the set welding

step is inapplicable for the selected

characteristic line.

Fig. 22: „noP“ (no program)

 Select a suitable welding step with turning

knob 45.

13.7 Mode Manual

Manual welding mode allows welding inde-

pendent of characteristic lines.

 Press key menu 48.

 Select menu option „characteristics“ by

turning operation knob 52.

 Confirm menu option „characteristics“ by

pressing operation knob 52.

 Select menu option „manual“ by turning

operation knob 52.

 Confirm menu option „manual“ by pressing

operation knob 52.

 Press key 46, 50 or 51 to exit menu and

return to standard display.

Fig. 23: Manual mode

13.8 Secondary parameters

MULTIMIG 200

Start-up

18

 Press key secondary parameter 46 or 51 to

open the secondary parameter menu.

 Select the required secondary parameter by

turning operation knob 52.

 Confirm set secondary parameter by

pressing operation knob 52.

 Set parameter value 72 as required by

turning operation knob 52.

Fig. 24: Secondary parameters

70 Symbol secondary parameter

71 Factory setting

72 Parameter value

 Confirm parameter value 72 by pressing

operation knob 52.

 Press key 46, 50 or 51 to exit menu and

return to standard display.

13.9 Tiptronic

The Tiptronic function provides 10 separate

jobs. All settings and adjustments made on the

control panel are stored in each job.

The Tiptronic function also gives the user

certain advantages, e.g. frequently recurring

welding jobs can be assigned to specific job

numbers, or different welders can save their

individual settings in „their“ job.

Factory setting for Tiptronic function is de-

activated.

Activate Tiptronic

 Press key menu 48.

 Select menu option „Tiptronic“ by turning

operation knob 52.

 Confirm menu option „Tiptronic“ by pressing

operation knob 52.

 Set menu option „Tiptronic on/off“ by turning

operation knob 52.

 Confirm menu option „Tiptronic on/off“ by

pressing operation 52.

 Set and confirm option „on“ with operation

knob 52.

Fig. 25: activate Tiptronic

 Press key 46, 50 or 51 to exit menu and

return to standard display.

Save job

 Press key Tiptronic 50.

 Set menu option „Job save“ by turning op-

eration knob 52.

 Confirm menu option „Job save“ by pressing

operation knob 52.

 Select the required saving position

(J00 … J09) by turning operation knob 52.

 Confirm the job by pressing operation knob

52.



If the job to be saved is already existent / al-

located; a safety question before overwriting

appears.

MULTIMIG 200

Start-up

19

Fig. 26: safety question

 Select „YES“ for overwriting the job by

turning operation knob 52.

 Confirm „YES“ by pressing operation knob

52.

Fig. 27: Save job

 If required the job name can be changed.

(see „edit job ext).

 Save the job by pressing key 51.

 Press key 46, 50 or 51 to exit menu and

return to standard display.

Edit Job-text

 Press key Tiptronic 50.

 Set menu option „edit job text“ by turning

operation knob 52.

 Confirm menu option „edit job text“ by

pressing operation knob 52.

 Select the job no. where text must be edited

by turning operation knob 52.

 Confirm the job no. by pressing operation

knob 52.

Fig. 28: edit job text

 Press key mode 47 to edit numbers.

 Press key secondary parameter 46 to edit

letters.

 Repress key secondary parameter to

change between capital and small letters.

 Set the required number or letter by turning

operation knob 52.

 Confirm number or letter by pressing op-

eration knob 52.

 Repeat above procedure for each character.

 Use key Tiptronic 50 to go back stepwise in

order to correct a character.

 Press key secondary parameter 51 to fi-

nalize the saving process.

 Press key 46, 50 or 51 to exit menu and

return to standard display.

Select job

 Press key Tiptronic 50.

 Set menu option „select job“ by turning

operation knob 52.

 Confirm menu option „select job“ by press-

ing operation knob 52.







A listing of all existing jobs will be displayed

in the menu. The currently selected job is

marked with a tick (√) on the right side.

MULTIMIG 200

Start-up

20

Fig. 29: select job

 Set the required job by turning operation

knob 52.

 Confirm the job by pressing operation knob

52.

Active job summary

Tiptronic-Jobs can be set either active or in-

active.

When PowerMaster torch is connected and

Tiptronic function is active, use rocker switch to

switch between active jobs.

 Press key Tiptronic 50.

 Select menu option „Active Jobs“ by turning

operation knob 52.

 Confirm menu option „Active Jobs“ by

pressing operation knob 52.







A listing of all existing jobs will be displayed

in the menu. All active jobs are marked with

a tick (√) on the right side.

Fig. 30: Active job summary

 Select the job to be activated or deactivated

by using operation knob turning knob 52.

 Activate or deactivate the job by pressing

operation knob 52.

 Press key 46, 50 or 51 to exit menu and

return to standard display.

Copying a job

 Press key Tiptronic 50.

 Select menu option „copy job“ by turning

operation knob 52.

 Confirm menu option „copy job“ by pressing

operation knob 52.

 Select the job to be copied by turning op-

eration knob 52.

Fig. 31: Copy job: source

 Confirm the job by pressing operation knob

52.

 Select the job to be overwritten by turning

operation knob 52.

Fig. 32: Copy job: target

 Confirm the job by pressing operation knob

52.







Safety question „copy job?“ appears.

 Select „YES“ to copy by turning operation

knob.

Page is loading ...

Elektron MULTIMIG 200 Operating instructions

Elektron MULTIMIG 200 Operating instructions

Other documents