HSM shredstar x10 Operating Instructions Manual

Brand: HSM

Model: shredstar x10

Category: Paper shredders

Type: Operating Instructions Manual

This manual is also suitable for

shredstar X6pro

HSM shredstar x10: Securely shred your confidential documents and data with this high-performance cross-cut shredder. Its P-4 security level ensures your sensitive information is destroyed into tiny pieces, meeting strict data protection standards. With a cutting capacity of up to 7 sheets per pass, it efficiently handles your shredding tasks.

07/2016

OPERATING INSTRUCTIONS

NOTICE D‘UTILISATION

INSTRUCCIONES DE SERVICIO

shredstar X6pro

shredstar X10

2 HSM shredstar 07/2016

english: Paper shredder HSM shredstar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

français: Destructeur de documents HSM shredstar . . . . . . . . . . . . . . . . . . . . . . . . . 9

español: Destructora de documentos HSM shredstar . . . . . . . . . . . . . . . . . . . . . . . 15

07/2016 HSM shredstar 3

english

Risk of combustion!

Do not use cleaning agents or

pressurized air sprays which

contain inﬂ ammable substances,

as they could ignite.

Dangerous for children and

others!

The machine may not be used

by persons (including children

under 14 years of age) with lim-

ited physical, sensory or mental capabilities

or with a lack of experience and knowledge,

unless they are supervised by a responsible

person or are instructed by them on the use

of the machine. Children must be super-

vised to ensure they do not play with the

machine.

Do not leave the document shredder

switched on when it is unattended.

Dangerous mains voltage!

Improper handling of the machine

can lead to an electric shock.

– Check the machine and cable regularly

for damage.

Switch the shredder off if it is

damaged or not working correctly

or before relocating or cleaning it

and disconnect it from the mains.

– Make sure that no water gets into the

shredder. Do not immerse the power

cable or the power plug in water. Never

touch the power plug with wet hands.

– Never pull the plug out of the socket

using the power cable. Always pull out

the plug directly.

Note

indicates information for the effective

operation of the machine without risk of

danger.

NOTICE

alerts you to potential property damage.

Safety instructions

Before using the machine for the

ﬁ rst time, read the operating

manual, and keep it for later use

and to pass on to any subsequent

users.

Observe all safety instructions onto the

machine.

Risk of injury from sharp

blades.

Never reach into the slot of the

paper feed.

Risk of injury from being pulled

in!

Keep long hair, loose articles of

clothing, ties, scarves, jewellery,

etc. away from feed opening.

Material with the tendency to form

loops, e.g. tapes, strapping mate-

rial, etc. must not be shredded.

1 Explanation of symbols and

safety instructions

WARNING

The safety alert sign with the signal

word WARNING and text on a grey back-

ground warns of the risk of serious to

life-threatening injuries.

4 HSM shredstar 07/2016

english

2 Proper use, warranty

The document shredder is intended for

shredding paper and small quantities of CDs/

DVDs and credit cards or store cards.

NOTICE

The paper must not have any large paper

clips attached.

Do not insert envelopes with

windows, padded envelopes, newspapers,

foils, laminated documents, cardboard, plas-

tic, adhesive or hard materials.

The warranty period for the document shred-

der is 2 years. This warranty excludes wear,

damage due to improper handling, natural

depreciation, and actions taken by third par-

ties.

3 Overview

1 Shredded material container

2 Safety instructions

3 Feed opening for paper

4 Operating and display unit

5 Feed opening for CDs/DVDs and cus-

tomer/credit cards

6 Mains switch

7 Type plate on the underside of the cut-

ting head

1 2 3 4 5 6 7

Power

Overload

Overheat

Bin full

Operating and display elements

Operation button

Display option:

Ready for operation

Overload

Motor overheats

Bin full

Reverse button

07/2016 HSM shredstar 5

english

4 Initial start-up 5 Operation

WARNING

Dangerous mains voltage!

Improper handling of the machine can lead

to an electric shock.

• Only use the machine in a dry room

indoors. Never operate the machine in

damp rooms or in the rain.

• Keep the machine, the plug and cable

away from open ﬁ re and hot surfaces.

The ventilation slots must not be blocked

or covered and there must be at least

5 cm space between the shredder and

any wall or furniture.

• Make sure that the power plug is easily

accessible.

• Before you insert the power plug, make

sure that the voltage and frequency

of your power supply comply with the

information on the name plate.

• Set mains switch at rear of paper shredder

to “I”.

• Press the operation button.

 The “Ready for operation” indicator

lights up.

Switching on the shredder

Shredding paper

• Insert the CD container provided into the

bracket on the inside of the shredded

material container.

• Plug the power supply into a properly

installed socket using the adapter.

Note

Do not use both cutting units at the same

time. Destroy paper and CDs/credit cards

separately.

Note

You can increase the service life of your

shredder by removing staples from the

paper.

• Feed the paper into the centre of the

paper slot. The light barrier starts the

cutting unit automatically. Therefore, with

thin paper strips, make sure the light bar-

rier detects them.

 If feed opening is free again, the cut-

ting unit shuts down and the shredder

switches to standby.

6 HSM shredstar 07/2016

english

Shredding CDs / DVDs

LED displays, troubleshooting

• Press the operation button.

 The “Ready for operation” indicator

goes out.

• Set mains switch at rear of paper shredder

to “0”.

Switching off the shredder

WARNING

Danger of injury by splinters!

Depending on the type of mate-

rial, splinters can ﬂ y out of the

cutting unit while shredding CDs

and injure your eyes.

• For this reason, wear protective goggles.

• Insert credit card in centre of the feed

opening. Dispose of the shredded material

and the waste paper separately.

Shredding credit cards and store

cards

• Feed in just one CD/DVD in the middle of

the feed opening.

• Empty the CD container at the latest

after shredding 5 CDs. The separate CD

container is in the shredded material con-

tainer.

Power

Appliance is ready for use.

Overload

Machine is overloaded. You have fed in

too much paper.

 The cutting unit runs in reverse for a few

seconds and pushes the paper back out

again.

• If necessary, press the reverse button “R”

to remove the stack of paper.

• Take half the stack of paper.

• Feed the paper in portions.

Overheat The motor has overheated.

• Let the shredder cool down for approx.

30 mins. before using it again.

Cutting unit runs continuously

- The light barrier in the paper feed is

blocked with paper. Press the paper

through with a thin strong piece of card-

board.

- The light barrier is soiled with paper dust.

Clean the sensor with air pressure, a dry

paintbrush or a cloth.

Bin full

 The cutting unit is switched off.

NOTICE

Empty the cut material container, immedi-

ately because if it is too full, malfunctions

can occur in the cutting system.

There are recessed handles in the housing

top to make it easier for you to lift the cutting

head.

For all other malfunctions, check whether the

cutting head is correctly positioned on the

shredded material container before contact-

ing our customer service.

07/2016 HSM shredstar 7

english

7 Cleaning and maintenance 8 Disposal / Recycling

Electrical and electronic old

devices contain a variety of valu-

able materials, but also hazardous

substances which were required

for function and safety. Incorrect

disposal or handling can be dan-

gerous to your health and the environment.

Never dispose of old devices in the house-

hold waste. Observe the current applicable

regulations and use the collection points for

returning and recycling electric and elec-

tronic devices. Dispose of all the packaging

materials also in an environmentally-respon-

sible way.

9 Scope of delivery

• Paper shredder in carton packing

• Operating instructions

Acces so ries

• Special cutting block oil 250 ml

order No.: 1.235.997.403

See page 24 for our customer service

addresses.

Clean the document shredder only with

a soft cloth and a mild soap-water solu-

tion. However, no water must enter the

equipment.

Oil the cutting unit when

cutting performance

decreases or the device

becomes noisy, or every

time you empty the waste

container. Only use HSM special lubricating

oil for the cutting unit to do this:

• Spray the special cutting unit oil through

the paper feed along the entire width of

the cutting shafts.

• Run the cutting unit backward without

adding paper. To do so, press the R key.

 Paper dust and particles are shaken off.

WARNING

Dangerous mains voltage!

Improper handling of the machine can lead

to an electric shock.

Switch the shredder off before

relocating or cleaning it and

disconnect the mains plug.

Service work which requires the

housing covers to be removed

may only be carried out by HSM

Customer Service and service

technicians of our contractual

partners. See page 24 for our customer

service addresses.

8 HSM shredstar 07/2016

english

This document shredder meets the applicable harmonisation legislation of the European Union:

• Low Voltage directive 2014/35/EU

• EMC directive 2014/30/EU

• RoHS directive 2011/65/EU

The EU declaration of conformity can be requested from the manufacturer.

10 Technical data

* The maximum number of sheets (DIN A4, 70 g/m² or 80 g/m²), fed lengthways, which can be cut in one cycle. The

performance data is determined when the motor is cold and the cutting device is freshly oiled. A weaker mains voltage or

a different mains frequency to the one speciﬁ ed could result in less sheet capacity and increased noise during operation.

The sheet capacity can vary depending on the structure and properties of the paper and on the way it enters.

Type X6pro X10

Cutting type Cross cut

Cut size 2 x 15 mm (1/16 x 5/8“) 4.5 x 30 mm (3/16 x 1 1/8“)

Security level DIN 66399

P-5 / O-1 / T-1 / E-2 P-4 / O-1 / T-1 / E-2

Cutting capacity * (sheets), A4 80 g/m

70 g/m

Cutting speed 42 mm/s

Intake width 220 mm / 8.7“

Power supply 120 V / 60 Hz

Power consumption

with max. number of

sheets

160 W

Weight ?? kg ?? kg

Shredded material container volume 20 l / 5.3 gal

Separate cutting unit for CD/DVD/customer and credit cards

Cutting type Strip cut

Cut size 25 mm

Cutting capacity 1 CD/DVD (max. 1.2 mm thick) or 1 credit card / store card

General data

Operating mode Brief operation

Operating time 7 min

Cooling time 45 min

Ambient conditions in operation:

Temperature

Relative humidity

Height above sea-level (MSL)

-10 °C to +25 °C

max. 90 %, without condensation

max. 2,000 m

Size W x D x H 345 x 245 x 385 mm / 13.6“ x 9.6“ x 15.2“

Sound pressure level emissions

(Idle running/ load)

55 dB(A) / 62 dB(A)

HSM shredstar x10 Operating Instructions Manual

Brand: HSM

Model: shredstar x10

Category: Paper shredders

Type: Operating Instructions Manual

This manual is also suitable for

shredstar X6pro

Download PDF

report

HSM shredstar x10 Operating Instructions Manual

This manual is also suitable for

HSM shredstar x10 Operating Instructions Manual

Related papers

Other documents